Search Documents

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By Soorkty Elarabi

The aim of this paper is to discuss the impact of end bearing plate on the capacity of micropile. Preliminary studies have been made in Sudan in specific area of cohesive soil. Experimental works were carried on a number of micropiles with and without end bearing plate. Same diameters, lengths and techniques of placing cement grout are considered, there after the axial load test applied to find out the capacities of micropiles in both cases. Deduced results in each case show that the end bearing plate has no positive impact on micropile capacity.

Oct 1, 2022

By Dachun Liu, Lei Shi, Yongnian Dai, Bin Yang, Yang Tian, Tao Qu

The carbonthermal reduction of high Mg–Si nickel laterite was studied under vacuum. The effects of adding calcium oxide and the reducing agent on the reduction of silicon in residue were studied at pressures of 10–200 Pa and different temperatures, with varying proportions of carbon and CaO. The analysis of the residue was performed using X-ray diffraction and chemical composition analysis. The results show the following: At 1350 °C with a C/O ratio of 1.5:1, the recovery of Si reached a maximum 71.09%. Under these conditions, Si exists mainly in the forms of Fe3Si, Fe2Si, FeSi and SiC. The recovery of Si was above 80% when the temperature was 1450 °C, the C/O ratio 1:1, and 15% addition of CaO. When CaO addition was 22.61%, all of the solid phase was Ca2SiO4.

Mar 1, 2017

By International geochemical

During the production of the Geochemical Atlas of Finland till samples were collected throughout Finland at a density of one sample per 300 km2. The material studied was the fine fraction of till (less than 0.06 mm). The geochemical mapping has shown that elements that are locally enriched in bedrock in the form of ore mineralisation are also enriched in a wide area of the surrounding till. These anomalous enrichments of ore elements take the form of rectangular or curvilinear zones that are some tens of kilometres wide and hundreds of kilometres long. The mineralised zones host ore deposits of different genetic types and can be termed "ore provinces". They stand out prominently on the geochemical maps and can be divided into sub-units of different chemical composition.

Jan 12, 1992

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

The paper describes the process of collecting detailed accounts of near-miss incidents and turning them into impactful visual stories using graphic simulation. The aim is to create high-quality training materials to reduce haul-truck-related accidents and fatalities in mining.

Sep 1, 2023

By R. Kumar, A. K. Verma

"In this paper, an anisotropic shear behavior of rock joints is investigated under constant normal load condition (CNL). The natural rock joint roughness is transferred to artificial rock samples using room temperature vulcanizing (RTV) silicon rubber. Artificial cylindrical rock joint samples (90 mm diameter and 50 mm height) are made by mixture of cement, sand, and water in the ratio of 1:1.5:0.45 (by weight). Direct shear tests are conducted on these samples in twelve directions at 30º apart at four different normal stresses (250kPa, 500kPa, 1000kPa, and 1500kPa). Thus, 48 samples are tested in laboratory. Test results shows that the peak shear strength (?) of rock joints is anisotropic in nature due to change in morphological features in particular shearing direction. Joint roughness coefficient (JRC) is determined in each shearing direction by trial and error method using Barton’s model (1973). Further, cohesion ( c) and angle of friction ( ? )of joint surface in each direction is determined. Finally, a relationship between angle of friction ( ? ) and joint roughness coefficient (JRC) is developed. Experimental shear strength and Barton’s shear strength is compared and it is found that effect of anisotropic decreases with increasing normal stress. INTRODUCTIONRock mass is generally composed of discontinuity which refers collectively to joints, faults, bedding plane and folds etc. ISRM (1978) defined joint as a line of break of geological origin along which there is no visible displacement. Joint is three dimensional discontinuity which composed of two matched/mismatched surfaces. The presence of joints in rock mass plays an important role to define its overall shear strength, deformability behavior, in-situ stresses and hydro-geological properties. The shear strength of rock joints is important in the design of near surface/ deep geotechnical works (mining excavation, dam foundation, power plants, underground caverns, and slopes).In last 40 years, many constitutive models are developed to predict shear strength of rock joints under CNL conditions (Patton 1966; Landanyi and Archambault 1969; Barton 1973; Goodman 1976; Barton and Choubey 1977; Plesha 1987; Desai ad Fishman 1991; Amadei and Saeb 1992; Maksimovic 1992; Wibowo et al. 1993; Huang et al. 1993; Amadei et al. 1998; Indraratna 2000; Homand et al. 2001; Wang et. al. 2003; Samadhiya et. al. 2008; Asadollahi and Tonon 2010; Ghazvinian et al. 2012). These constitutive models have limitations to predict shear strength of rock joints in one direction. Till date, among all constitutive models, Barton (1973) model is widely used in practice due its simplicity. It includes parameters such as joint roughness and joint compressive strength (JCS) to quantify joint surfaces."

Jan 1, 2015

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Grazyna Zakrzewska-Trznadel

The paper outlines the main objectives of the project that concern the evaluation of the possibility of uranium production from indigenous resources since Poland enters the nuclear program. The best available technologies are considered for uranium extraction and obtaining the yellow cake - U3O8. Liquid-liquid extraction with novel extracting agents, as well as membrane processes for separation of by-products will be tested in course of the project. The technological part will be completed with techno-economical analysis. Acknowledgement The studies were supported by the POIG project, No 01.01.02-14-094-09-00 ?Analysis of the possibility of uranium supply from domestic resources?.

Aug 1, 2010

By Alessandra Souza Martins

O aço inoxidável super duplex vem apresentando um desempenho satisfatório em ambientes de maior agressividade. Esse tipo de aço possui boas propriedades de resistência mecânica, resistência à corrosão e tenacidade ao impacto. Entretanto, mesmo apresentando desempenho satisfatório, esses aços podem apresentar problemas de corrosão quando sofrem algum tratamento térmico, devido à precipitação de uma fase deletéria chamada de alfa linha (?’), a qual precipita em temperaturas entre 300°C e 550°C e pode ocasionar uma diminuição da resistência à corrosão e tenacidade do material. Portanto, o objetivo deste trabalho é avaliar a resistência à corrosão dos aços inoxidáveis super duplex de grau 5A e 6A após sofrerem tratamento térmico a 475oC. A diferença entre os aços de grau 5A e 6A ocorre na presença de cobre e tungstênio na composição química do aço com grau 6A. A resistência à corrosão dos corpos de prova foi avaliada por meio das seguintes técnicas eletroquímicas: polarização anódica, espectroscopia de impedância eletroquímica e temperatura crítica de pite. A resistência mecânica dos corpos de prova foi avaliada por meio da técnica de dureza Brinell. Foi realizada também a caraterização microestrutural e a quantificação das fases do material. Os resultados mostraram um aumento da dureza do material, indicando um aumento da presença da fase ?’ com 10 horas de tratamento térmico apresentaram maior resistência à corrosão.

Aug 8, 2018

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By Markus Thewes, Mario Galli

"INTRODUCTIONProject-related studies showed that lab tests are a helpful tool for the planning of EPB tunneling and soil conditioning in cohesionless soils. This type of ground commonly represents the extended application range for EPB shields, which demands for a treatment with additives. Considering soil conditioning with foam, so far, approaches exist for the investigation of the foam quality and of the conditioning behavior of soils (e.g. (EFNARC GUIDELINES 2001 2003)), but not any standards for testing procedures related to soil conditioning. State-of-the-art research on the topic is and was conducted for example in Bochum (Germany) cf. (Budach 2012; Maidl 1995), in Lyon (France) cf. (Quebaud et al. 1998), in Oxford and Cambridge (Great Britain) cf. (Borghi 2006; Peña Duarte 2007), in Delft (Netherlands) cf. (Bezuijen and Schaminée 2001), in Turin (Italy) cf. (Borio 2010; Peila et al. 2013; Vinai 2006), and in Aachen (Germany) cf. (Vennekötter 2012). Additionally, applied science is reported by the tunneling practice and suppliers of conditioning agents. Although the research focus in all these and further studies varied, similar test methods and test series were applied. A standardization of essential properties and testing methods (setup and procedures) however did not take place. The results from laboratory testing can only function as index values for practice because in the studies, production and application of the conditioning agents mainly takes place under atmospheric conditions. Nevertheless, the tests enable basic understanding of feasibility as well as processes and interactions going on during soil conditioning. For recommendations for standardized and reproducible testing see (Budach 2012; Budach and Thewes 2015).The most extensive investigations on the flow behavior of soil-foam mixtures have been performed by using the slump test from concrete engineering, cf. (DIN EN 12350-2 2009-08), which originally is applied on evaluating the workability of fresh concrete. Although this test does not describe the actual flow behavior, it rather represents an index on the workability, very much experience exists with this test method. Besides others, the workability – or flow behavior – of the EPB support medium certainly is a major factor of influence on the properties of the material in the excavation chamber and thus, for effective tunneling with EPB shields, cf. (Galli and Thewes 2014). For a summary of various investigations on the workability of conditioned soils using the slump test and resulting recommended slump ranges see (Budach 2012; Vinai 2006). Thereof, slumps between 10 and 20 cm have been reported as suitable workability for EPB applications. However, there is actually not much known about the real flow behavior of soil-foam mixtures related to rheological properties such as the viscosity (?) or potential yield stresses (t0). These physical values are necessary for a realistic determination of face pressure, for the design of required torques, and for an evaluation of the material flow at different locations in the excavation chamber, in the screw conveyor or on the conveyor belt. To generate a linear pressure distribution at the tunnel face, as it is assumed a priori, a low-viscosity fluid is favorable, whereas in the screw conveyor, a high-viscous fluid is needed for a controlled pressure decrease. On the conveyor belt, yield stress plays an important role preventing deliquescence and spilling from the belt. Attempts in characterizing the actual flowing of soil-foam mixtures have so far only been made by few researchers, the application of rheometry is rare."

Jan 1, 2016

By NIM REPORTS

Notices CONFRRENCE ON COMPUTRRS IN ENGINEERING The above Conference, which is being organized by the Electrical and Electronics Board of the Institution of Engineer!!, Australia, ill to be held in Sydney on 16th and 17th May, 1974. It is being planned in conjunction with the Sixth Australian Computer Conference and will be held during the week immediately preceding the latter. NIM REPORTS Report No. 1495 A method for the determination of ekmental sulphur on the surface of sulphide minerals. Report No. 1500 The chromatographic separation and determination of nobk metals in matte-leach residues. Report No. 1505 The production of the refractory aluminium saicates, with special refererence to South Africa. Report No. 1517 Computer-controlled flotation plants in Canada and Finland. Report No. 1526 Heat of solution as a control of aqueous-ammonia concentration. Report No. 1529 South African costs of equipment for the metallurgical industry (197).

Jan 9, 1973

By George Ross Green

[In discussion of the paper of Mr. J. C. Bayles, read at the New York meeting of September, 1890, Trans., xix., p. 18.1 It is often so difficult to locate the causes of failures of machinery and apparatus which can be examined and studied at leisure, that it is not surprising that the causes of explosions should escape detection. Usually the explosion is the first evidence that anything is amiss, and the time for observing the conditions is necessarily brief. An incident in a welding-works near Essen, Germany, might be cited as exemplifying what trifling causes may lead to disaster, and how difficult, under the most favorable conditions, it may be to discover them. A blowing-engine was arranged with two suction-pipes at each end of the blowing-cylinder—one leading to the air, and the other to the gas-holder. Each pipe was provided with a valve, and all were so adjusted that the cylinder drew in gas and air in the proportions found most advantageous. The gases from the cylinder were carried directly to the furnace through suitable pipes, and while the cylinder was provided with relief-valves, every effort was made to prevent explosions, principally by compressing the gases to a point where the rate of efflux of the mixture was greater than the velocity of combustion, if the expression is here allowable. It was found that the apparatus would work satisfactorily for some time, and then the relative proportions of the mixture would change, and an explosion might have been the result. Experiments consuming days were made to discover a method of averting this danger, but they were unsuccessful, until it was observed that the change in the composition of the mixture of gas and air took place when the gasometer began to rise or fall—the back-pressure due to friction when the holder was rising or its absence when falling being sufficient to change the conditions. As soon as this was discovered,

Jan 1, 1892

By Vaughan R. Voller

"Numerical methods for dealing with a temperature dependent conductivity are discussed. An approach based on a local application of a Kirchhoff transformation at the discrete level is presented. The application of this transformation - that does not require any inversion- is demonstrated on solving a two-dimensional test problem.IntroductionMuch is said in the recent literature on the modeling necessity of obtaining appropriate thermo-physical properties; in particular the requirement to account for properties that are ""strong"" functions of the depended variables, e.g., Temperature. Of course obtaining appropriate thermo-physical properties serves no purpose unless they can be accurately integrated into a discrete numerical calculation. The purpose of this paper is to examine how temperature dependent conductivities that exhibit discontinuities or rapid changes can be handled in a numerical code.The discussion will be made in the context of a control volume finite element method [1]. After a brief outline of control volume finite element fundamentals basic methods of dealing with discontinuous or rapidly changing thermal conductivity are discussed. This is followed by the presentation of the recently proposed local Kirchhoff method [2,3], The paper concludes with an investigation of the performance of the various conductivity schemes in solving two dimensional problems. This testing clearly shows the advantages (accuracy and implementation) in using the local Kirchhoff method."

Jan 1, 2001

By R. W. Bowers

In order to hoist the ore according to grades, stope samples are taken. Three equidistant grooves are picked across the breast at right angles to the dip of the ore, the part removed being caught in the hand and then put into a small bag. When there is broken ore in the breast, the lines are continued down the pile and a small amount taken at intervals of the length of the sampler's pick handle. The quantity of sample from each breast will be between 2 and 3 Ib. If there are two grades of ore, bessemer and non-bessemer, there are two sets of brass checks for each chute, each check stamped with the number of the chute; one set of checks has the word "bessemer" and the other "non-bessemer." Before any ore is removed from the chutes, it is the duty of one man to see that the proper set of checks is at each chute in the mine. As each motor car is loaded, a check is attached to it. When the train reaches the shaft, the sample man removes the check on the first car, notes the grade, and directs the motorman to spot it over the proper pocket. The check is then hung on a hook with the number corresponding to the chute from which the ore came. The sample man throws a short rope with a knot in the end over the car and at the point where the knot falls a standard scoopful is taken. This is placed in a large bag that hangs directly under the hook containing the checks for that particular chute. These chute samples represent a check on the grading of the various contracts and by counting the tags a check is obtained on the miner's tally of the ore going into each chute; the total of the checks represents the hoist. During the stocking season, a standard scoopful is taken from each top tram car. This sample is taken in the same way as the chute samples at the plats underground. Top-of-car Samples These samples are taken by using a rope, preferably a clothesline, knotted each 18 in. of its length, and a hammer and a scoop. The standard scoop measures 31/2 by 21/4 by 11/4 in. and holds about 1/2 Ib. of ore. The rope, as applied to the usual railroad cars at the mine, is knotted into fifteen sections. It is placed diagonally over the car from

Jan 1, 1925

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By J. L. W. Birkinbine

This paper is a discussion of a part of the mineral wealth of the States of Oaxaca and Paebla, Mexico. It does not refer to the precious metals, sonie mines of which, in these States, are said to have been worked before the advent of the Spanish conquistadores in the sixteenth century, as my purpose is to invite attention to the exploration of deposits of coal and iron-ores in the Mixteca region. The prominence given to coal is warranted by the great effect of the scarcity of fuel upon the industrial development of Mexico. Under the progressive administration of President Porfirio Diaz, the Republic has made wonderful advances in the past three decades; and this progress would have been greater but for the limitations imposed by expensive fuel. In the spring of 1906 I was detailed by the Birkinbine Engineering Offices, of Philadelphia, to accompany A. B. Adams, of New York, in a reconnoissance of reported deposits of iron-ores in the State of Oaxaca. The result of this expedition was the formation, in 1907, of the Oaxaca Iron & Coal Co., of which Mr. Adams became, and has remained, President and General Manager, and I have spent the past three years as Chief Engineer of this company in Mexico, principally in western Oaxaca, where field-headquarters were established. GEOGRAPHY AND POPULATION. Although the geographical and topographical features of the Republic of Mexico are well known, few realize that the majority of its population is domiciled in the States which immediately surround the capital city of Mexico, including the Federal District, Mexico, Tlaxcala, Morelos, Puebla,

Jan 1, 1911

By V. (“Viv”) R. Forbes

[ ] INTRODUCTION "The Liberal Party believes that the State's mineral resources belong to the people of Queensland and therefore it is essential that the state, on their behalf, obtains maximum benefit from the development of those resources." (Liberal Party, 1980 "Mineral Resources Policy" p.2). "Unless sound policies are implemented.... increased production of minerals will benefit only the already wealthy and the lucky few... A resources tax is essential to ensure that above normal profits are shared by the whole community.... Labor policies on taxation must ensure an adequate return from mining developments to the Australian people." (Labor Party Policy Paper, May 1982 "National Issues relating to rapid expansion of mineral production during the eighties". p.1, 37, 47). Judging from these statements, key political parties in Australia believe that mining profits are lightly taxed and that shareholders get most of the benefits. THE REALITY The Government Share of Income statement in Table 1 attempts to measure the government share of the income generated by the "Big Five" Australian mining companies - Broken Hill Pty Ltd. (BHP), CRA Limited, Utah International, MIM Holdings Ltd., and Western Mining Corporation ("WMC"). These companies control over 70% of Australia's mining industry including all the most profitable mining operations. They dominate the mining and processing of iron and steel, aluminum, manganese, coal, oil and gas, copper, lead, zinc, silver, nickel, gold, ferro-alloys and salt in Australia. They are also major world exporters of most of these products. They are thus a representative sample of the profit-earning side of the Australian mining industry. In their two most recent financial years these five companies had income before tax of A$6,980 million. The Government share of this income was A$6,285 million or 90%. The total market capitalisation of the Big Five is about A$8,480 million. (December, 1982). Governments thus consumed the equivalent of 82% of their total value in just two years. This was taking place while the politicians drafted the above statements calling for an "adequate" share for the people.

Jan 1, 1985

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970