Search Documents

Jan 1, 1986

By M. Olper, M. Maccagni

"The crude zinc oxides (CZO) produced in any thennal process dealing with EAF dust also contain lead, cadmium, and a considerable amount of halides (chlorides and fluorides). The high halide contents make these crude zinc oxides less and less attractive, both technically and economically, and a further refining procedure is nece'ssary to meet the zinc and zinc oxide market requirements.Hydrometallurgical techniques commercially used to dehalogenate the crude zinc oxides are not effective enough to upgrade the crude zinc oxides to the required specification for their direct use in the traditional sulphuric electrolysis by primary zinc producers.The EZINEX® PROCESS has solved the problem of the halides contained in the crude zinc oxides. This process is the only proven technology electrowinning zinc from a chloridebased electrolyte in a conventional cell house. This paper discusses the process economics taking the data from feasibility studies of different size commercial plants."

Jan 1, 2000

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

Mine waste and mine reclamation are topics of major interest to the mining industry, the government and the general public. This publication and its companion volume are the proceedings of a conference held in Pittsburgh, April 19-21, 1988. There were nine sessions (50 papers) that dealt with the geochemistry, hydrology and problems of mine waste and mine water, especially acid mine drainage. These comprise Volume 1. The nine sessions (43 papers) that dealt with reclamation and restoration of disturbed lands, as well as related policy issues, are included in volume 2. Volume 2 also contains the ten papers that pertained to control of subsidence and mine fires at abandoned mines. Poster session presentations are, in general, represented by abstracts; these have been placed in the back of both volumes.

Jan 1, 1988

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By Mark W. Booth

THIS paper deals with the subject of inbye power as the mechanical . engineer sees it, and invites discussion, particularly from the electrical engineer. At the outset, it will be necessary to clear the ground a little by some definite statements. In this question of compressed air versus electricity for the transmission of power and driving of machinery in underground workings, we must see that there are definite fields that compressed air on the one hand, and electricity on the other, can fill to much greater advantage than the other, and in which there can be little or no direct competition, at least for the present. It is under conditions where these fields overlap, and as to where the line must be drawn between the two, that the respective merits of each must be considered. Steam was the first means used to transmit power from the surface of a mine to drive underground machinery, and so long as distances were short and means possible to ensure fairly efficient use of the steam, and where the fire hazard was not in evidence, it gave fairly efficient service. I have in mind an instance during my own connection with the mines-a duplex pump at the shaft bottom at Princess colliery, driven by steam, and which used the steam compound and condensing; and, but for the mechanical difficulties, it was a not inefficient proposition. The steam was taken direct from the surface boiler-plant through a line down the shaft, and used directly at the pump, being in effect a straight conversion from coal to steam to work done. It was the mechanical arrangement, and failure of the pump in that direction, that led to its removal and replacement by something better in the way of an electrically driven turbine pump. Given modern mechanical arrangements, such as a steam-turbine drive on a high-speed turbine pump, and all other parts made in accordance with best practice in the art of steam generation and use, a steam-driven unit fully as economical would have been obtained. But the central electric supply station, and all that that means or promises (not always the same), turned the scale against steam.

Jan 1, 1936

By Donald Christofferson

This report documents the program conducted to demonstrate the application of a flywheel-powered propulsion system to underground mining shuttle cars. Such application can replace the present electrical trailing cable common to most shuttle cars and thereby eliminate those safety hazards, maintenance problems, and haulage route limitations inherent in the trailing cable. Described are the activities undertaken to specify and design a flywheel of optimum size, shape, and material; to identify the best concepts of input and output systems; and to achieve installation of the power package into a shuttle car. The resultant Flywheel-Powered Shuttle Car is an FMC Model 6L shuttle car, 6-ton capacity, 20-ton gross vehicle weight, powered by a flywheel system with 4.5-kilowatt-hour usable energy. The completed vehicle was delivered to the Bureau of Mines in Bruceton, Pennsylvania, for testing and evaluation.

Jan 1, 1986

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By D Gagnon, P Bouchard, F Vanier, E Soares de Lima Filho, J El-Haddad, M Sabsabi, G J. Wilkie, A Beauchesne, A Hamel, A Blouin, T Vaillancourt, F Boismenu, A Harhira, A Plugatyr, C Padioleau

Quantitative mineralogy is an established discipline in the geosciences and is aimed at providing mineral grade and texture information for geological and mineral processing applications. The two core technologies underpinning Quantitative Mineralogical Analysis (QMA) are Scanning Electron Microscopy (SEM) in combination with Energy-dispersive X-ray Spectroscopy (EDS). Technologies such as QEMSCAN and MLA are now routinely used to optimise the performance of large-scale mineral processing plants in the base and precious metal sectors. One of the major disadvantages of the QMA methods used today is extensive sample preparation requirements which make application of this technique to real-time mineralogical characterization not feasible. A breakthrough has been achieved by the National Research Council Canada in collaboration with CRC ORE by developing a novel Laser Induced Breakdown Spectroscopy (LIBS) based technology capable of real-time mineralogical characterization of process streams without sample preparation. The potential applications of this technology include, but not limited to, in-pit muck piles, underground draw points, cross-belt analysis as well as slurries. This paper describes the development of the LIBS-based technology from a proof-of-concept (TRL2) to the construction of a prototype sensor and its validation in a simulated environment (TRL5). Future work is being planned to test and further validate the LIBS sensor on a mine-site which will progress the technology to its next readiness level (TRL6).

Nov 10, 2020

The purpose of this study was to examine the problems of underground coal mining in the United States, and to develop recommendations for an integrated Research and Development Program aimed at resolving these problems. Specific objectives of the study were as follows: ? To identify the existing inadequacies that have adverse effect on Health, Safety, External Environment, and Productivity. ? To identify opportunities for technological advance s to correct these inadequacies. ? To develop an integrated Research and Development Program designed to accomplish the advances identified. Many of the recommended tasks are dearly long range; this is especially true of those for study of future mining systems. However, funding recommendations in this Report are presented for a 5 -year period, since the developments accomplished during this period will undoubtedly be a factor in the formulation of the follow on tasks. Where applicable, the recommended Research and :Development could include development and test of pilot model equipment.

Jan 1, 1970

By C. M. Acuna, M. Sherrington

In high temperature processes thermodynamic equilibrium is assumed and therefore chemical potential of elements, among the condensed phases, have to be the same. In such situation impurities distribute accordingly and their fractional distributions are affected by the masses of the coexisting phases. It has been claimed Teniente Converters perform quite well for smelting high impurity concentrates, especially in respect to volatilization and/or slagging. Production of high matte grade near white metal composition, requiring moderate oxygen enrichment in the process air, results in a huge mass of gas and therefore a high fraction of impurities report to it. Similarly, by recycling different sources of slag, flue dust or other materials, the mass of the final slag is increased and so do the masses of impurities reporting to the slag. Nevertheless, above a certain level the recycling of smelter byproducts is no longer feasible and the cycle has to be halted, unless higher impurity mattes are accepted. Although the process might be continued during converting and refining, lengthy and expensive measures have to be taken if suitable anode copper for electrolytic refining is to be achieved. In the present study samples of high arsenic matte grade and slag were obtained on a pilot scale. The matte samples, on the order 75%Cu, were equilibrated with slag at varying ratios in magnesia crucibles under CO/C02 atmospheres at 1523 K. After 24 hours equilibrium matte and slag were rapidly solidified and analyzed by copper, sulfur, iron and arsenic. Furthermore, industrial samples of matte and slag, in the order 75%Cu at 1523 K, were obtained via a special quenching sampling device to determine the association of copper and suspension of matte and copper in slag. Based on the results, the distribution coefficient of arsenic between slag and matte was evaluated along with copper species in slag and the fractional distribution of arsenic, in the coexisting phases, was determined as a function of the ratio mass of slag to mass of matte.

Jan 1, 2007

By BUREAU OF MINES

In 1948 the United States became a net importer of oil. Coupled with an unpre- cedented domestic production of 5,900,000 barrels daily, imports approximating 500,000 barrels made available a total supply of 6,400,000 barrels a day. Thus, by herculean effort, the oil industry was able to meet an extraordinary demand at home and, in addition, to ship abroad almost 400,00 barrels daily of petroleum and products. The country's oil position now differs greatly from that prevailing at the be- ginning of World War II. Then, actual oil production averaged about 4 million bar- rels a day, and productive capacity probably was greater than 5 million barrels a day. As the demand of the military and industrial machine grew with the rising tempo of the drive toward victory, the United States not only met its own needs but pro- duced about two-thirds of the total oil requirements of the Allied Nations, excluding Russia. As a people, we can be deeply grateful that the Nation's petroleum resources were adequate and sufficiently developed to support such a tremendous effort. Even in those critical hours when immediate needs were the paramount issues, a prudent Congress paused to contemplate the importance of an assured long-term supply of liquid fuels. From these deliberations came the Synthetic Liquid Fuels Act of 1944, which authorized research and development work on new sources of oil coal, oil shale, and agricultural and forestry products. ce World War II, a civilian demand for 6 million barrels of petroleum prod- ucts has become the order of the day every day. By drilling as many as 39,000 new wells a year, the production rate has been increased enough to meet domestic require- ments by a bare margin. Some imports were necessary, however, to fill both domestic and foreign demands, and these doubtless will increase. Is this policy of exploration within the United States and the development of oil in foreign countries adequate insurance for the fulfillment of our future national needs? This question has two aspects one purely civilian and economic in character and the other significant from the standpoint of our national defense. There are now approximately 4,000 producing oil fields in this country. At first thought, it would appear that production could decline in a considerable number of these fields without materially affecting the over-all daily output. However, 48 percent of the oil comes from only 111 major fields which contain 50 percent of the total proved domestic reserves. It is apparent, then, that the flow from large fields - having proved reserves of 100 million barrels or more each must be sustained if daily production is to be kept at the present levels. Essentially, this means that new major fields must be discovered about as rapidly or perhaps more rapidly than the older ones lose productive capacity. From 1940 through 1947, only eight major fields with estimated reserves of more than 100 million barrels each, were discovered and proved - an average of one such field a year. The total estimated reserve of these eight fields was less than 1 year's supply at the present rate of use. As drilling continues, some existing fields ultimately will prove reserves larger than those now known. Without a pronounced increase in the num- ber of major discoveries, however, the prospects for increasing our present productive level are not encouraging. Any gap that appears between domestic productive capacity and demand could be filled with supplies from proved oil resources abroad. Assuming cheap pipe-line and tanker transportation to the United States, freedom from exorbitant taxes and charges

Jan 1, 1949

By D. Farnell

Large semi-autogenous (SAG) or autogenous grinding mills have become the work-horse of the modern high volume concentrator. They typify the economy of scale - fewer, larger machines doing more work, more economically. With fewer machines, equipment reliability becomes of paramount importance. Realizing this, companies installing new or modernizing existing facilities have placed extraordinary emphasis on purchasing a reliable mill. This, in turn, has had a significant impact on mill design. Kennecott And Codelco - Two Different Approaches Last year, two of the world&apos;s largest copper producers, Codelco and Kennecott, undertook the modernization of their main grinding facilities at Chuquicamata and the Utah Copper Division (UCD) respectively. Both selected semi-autogenous milling and both, recognized the importance of the reliability of the primary mills. Each, however, decided on a different approach to optimizing reliability. Codelco placed the emphasis on technical innovation in design and opted for a gearless driven mill. Kennecott chose the more conservative approach of active participation and exceptional quality assurance in mill design and manufacture.

Jan 1, 1987

By The Staff

BEFORE going into detail on the subject to be presented, a brief outline of the Company&apos;s earl y history would not be out of place. Prospecting and mining on a small scale was started in 1876 on the site of the present open pit at Thetford Mines. The property was purchased from the Crown in 1878 and Johnson&apos;s Company was incorporated in 1885. It is owned and operated today by descendants of the original shareholders. Many employees, through their fathers and grandfathers, have service records dating back three generations. The principal asbestos deposit at Thetford Mines is pear-shaped, with surface dimensions of about 2,200 feet in length by 1,300 feet in maximum . width. Its long axis strikes northeast and the dip is nearly vertical, but irregular in detail. It is known to extend to a depth 1,200 feet below the original surface, but its area at that depth has not been determined. Ownership of this deposit is divided among three active Companies: the Asbestos Corporation, Limited; Bell Asbestos Mines, Limited; and John-son&apos;s Company. Johnson&apos;s Company owns a section about 1,000 feet in length and 500 feet in width, bounded on the northeast by the King mine of the Asbestos Corporation and on the northwest by the Bell pit. On Johnson ground, there was originally a large outcrop o~ asbestos rock which dipped toward the south below overburden. This was mined until recently by open pit, the overburden being stripped off as far southward from the original outcrop as was economically possible. As the. pit was deepened, within side walls maintained at a maximum safe slope, its floor area, of course, became progressively smaller, and eventually the pit would have wedged out against the Bell property line. It became necessary, there-fore, to introduce some other method of mining before production became seriously curtailed by a shrinkage of the pit area.

Jan 1, 1941

By Sean Peterfreund, Grant Finn, Ty Jahn

For urban underground development involving tieback anchors for excavation support, authorities having jurisdiction typically require tiebacks to be de-tensioned before project completion. This paper updates “A Proactive Approach to Tieback Anchor De-tensioning” (by Peterfreund and Finn, published in the 2017 RETC Proceedings), which discussed a new method employed in a cut-and-cover transit station project. Since publication of that paper, 237 tiebacks were successfully and rapidly detensioned from using a small-diameter drill to cut strands from the surface. To the authors’ knowledge, this was the first intentional large-scale use of a drilling method for this purpose.

Jun 13, 2023

By R. E. Grant

THE Cerro de Pasco Railway Co., owned and operated by the Corporation, is a common carrier whose chief functions are transportation of ore and concentrates from the mines at Cerro de Pasco to the smelter in Oroya, and haulage of coal from the coal mines at Goyllarisquisga to the coal washery at Fundicion. Connecting with the Peruvian Central Railway at Oroya, the C. de P. Railway maintains joint, daily freight and passenger service from Lima and the port of Callao to Cerro de Pasco, terminal of the C. de P. main line and gateway to the Huanuco Valley. Extending from Oroya to Cerro de Pasco the main line is a standard-gauge roadbed of 70-lb. rail, 132 km. long with a maximum compensated grade of 2.25 per cent and a curvature of 16°, climbing from an elevation of 12,272 ft. above sea level at Oroya, lowest station on the line, to 14,208 ft. at Cerro de Pasco. The highest point reached by the C. de P. is on the coal branch at Alcacocha where the rails are 14,385 ft. above the sea.

Jan 1, 1945

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016