Search Documents

By Andrew Torok, Thomas D. Thompson

Research efforts have not developed techniques for the complete desulfurization of coal that is needed to reduce air pollution caused by burning coal and to reduce the sulfur in metallurgical coke. Sulfur in coal occurs in three forms and of these, the pyritic sulfur occurs as discrete mineral particles and, at least theoretically, should be subject to physical rejection. Pyrite occurring in hard rock mining is concentrated by froth flotation; therefore, the possibility of removal of pyrite from coal by flotation does exist. With this possibility in mind, the flotation and adsorption characteristics of ore and coal-pyrite were compared while using potassium ethyl xanthate as the collector.

Jan 1, 1973

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By Tony P. Suckling

This paper describes an investigation into the bleeding behaviour of bentonite slurry observed on a trial diaphragm wall panel. The bleeding is thought to be due to the bentonite experiencing a chemical reaction leading to settlement of the solids within the fluid, possibly as a self-weight consolidation process. The trial panel was constructed in a busy airport environment where many different chemical products are used for de-icing the aeroplanes, runways, apron areas, vehicle access and pedestrian routes. The relationships between slurry contamination, bleeding, bentonite hydration time and filter loss behaviour were examined as no relevant published literature could be found. The results show that the amount of bleed strongly depends on both the degree of contamination and the hydration time. It is concluded that bentonite fluids should be allowed to sit in the storage tank for at least 24 hours after mixing, and that the filter loss test is a quick and effective method to determine the potential for bleeding of contaminated slurries.

Jan 1, 2011

By I. W. van der Merwe

Recently, a new kind of filtration has emerged, namely nano-filtration (NF). It is a membrane-based process which exhibits totally unique separation characteristics for dissolved salts as well as for many non-charged species. By exploiting the particular separation characteristics of this new membrane type, many unique and novel separations have been made possible. The basis for separation by nanofiltration is the negative surface charge of the membrane. This results in rejection of multivalent anions, whilst associated cations are also rejected to maintain electro-neutrality. This peculiar property enables separation of dissolved ions such as sulphate and copper from acid, whilst the acid may be purified for reuse. This paper aims at providing an overview of the principles of nanofiltration, illustrated by particular examples.

Jan 1, 1998

The New Broken Hill Consolidated Airshaft is the first major undertaking in the development of New Broken Hill Consolidated Ltd's. property, which adjoins that of The Zinc Corporation Ltd. on the latter's southern boundary.The Zinc Corporation ore-body has a southerly pitch. The Zinc Corporation's New Main Shaft is 1000 ft. north of the common boundary, and the general plan of development of the New Broken Hill Consolidated property is by driving south from this shaft on the lower levels. No downcast airway from the surface was available south of the Zinc Corporation's New Main Shaft; this shaft acts as the main downcast to the bottom of the Zinc Corporation mine, the general air flow then being northward and upward to the upcast shaft at the extreme north end of the Zinc Corporation property.Rock temperature is 920 F. at 2000 ft., increasing by 10 Fahr. each 72 ft., the rock temperature at 3000 ft. being estimated at 1060 Fahr. With the general air flow northward from the Zinc Corporation's New Main Shaft, adequate ventilation under these temperature conditions would not be practicable for any great distance south of this shaft without another main airway from the surface. Accordingly the New Broken Hill Consolidated Airshaft is being sunk at a point 1000 ft. south of the common boundary, i.e., 2000 ft. south of the Zinc Corporation's New Main Shaft, to ventilate future New Broken Hill Consolidated workings and that part of the Zinc Corporation mine between the boundary and the New Main Shaft.

Jan 1, 1940

By Michael Tenenbaum, C. C. Brown

Numerous investigatiolls have been carried out to determine the total oxygen present in the basic open-hearth bath and the results of these studies have clearly defined the factors controlling the bath oxidation during the period prior to deoxidation. On the other hand, very little is known concerning any changes in total oxygen content that may occur during deoxidation, tapping and teeming. The need for such additional data is continually becoming more apparent, since there is no strict technical basis for selecting any particular deoxidation practice. Many steels are made for the same purposes and to the same chemical analyses by widely differing practices. Apparently, each practice is satisfactory. However, it would be desirable to establish more definitely the effects and relative merits of the individual practices. Such information could be used to give a definite foundation for evaluating various types of deoxidation. In order to approach this problem, a study was made of the changes effected in the total oxygen content of several grades of steel by representative open-hearth deoxidation practices. To carry out such studies, it was necessary that a reliable testing procedure for determining the oxygen content of the steel bath and the ingot mold be established. Before entering on any extensive testing program, consideration was given to the available methods of obtaining steel samples and analyzing for oxygen. Testing Procedures It has been shown5-9 that in solidified steel oxygen may ekist in combination with iron, manganese, silicon, aluminum, titanium, chromium and carbon, depending upon the amount of these elements in the sample. In molten steel, however, there has been no direct distinction of the various oxides. Accordingly, the total active oxygen in the molten steel bath is designated by the symbol 0. During deoxidation, various oxides may be present either in solution in the molten steel or as solid or liquid inclusions. Any sample taken from the molten steel for oxygen analysis will include both the dissolved and the mechanically included oxygen. Similarly, samples of the solid steel product will also include the two forms of Oxygen' Methods of Samplirzg the Molten Steel Bath In order to obtain a true oxygen analysis from liquid steel, this element must be completely retained in the solidified sample. Several methods have been proposed whereby this stabilization can be effected. As early as 1915, Kichlinelo proposed a method for testing molten steel, in which the oxygen combined with some added aluminum. The concentration of the resultant aluminum oxide was determined by chemical analysis. This method was

Jan 1, 1945

By Melvin A. Jennings

Ion-exchange technology for precious metals recovery is at a turning point. Some very exciting technology has been developed in the past five years which should lead to commercialization of the process. Ion-exchange will allow not only for the recovery of gold and silver, but also will allow for the recovery of cyanide form plant tailings. This process may soon be competitive with Merrill-Crowe for silver and once this occurs, it will become the process of choice.

Jan 1, 1991

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010

By Patrick M. Eduafo, Brajendra Mishra, Mark L. Strauss

Direct acid leaching of rare earth metals (REMs) from waste lamp phosphors is non-selective, leading to co-dissolution of impurities mainly calcium, phosphorus, silicon, iron and zinc. Calcining the phosphor powder at different temperatures followed by leaching with HCl isn’t efficient for the extraction of all the chief rare earths especially cerium (Ce), lanthanum (La) and terbium (Tb). Therefore, multi-stage leaching operations are required for the separation of the REMs in phosphor dust. This paper will outline a new process for extracting Ce, La, Tb, Eu and Y from waste fluorescent lamps using a three-stage leaching and separation process. A flowsheet has been developed which shows this process is selective and efficient.

Jan 1, 2015

By Peter Zhang

Room and pillar mining under shallow depth is usually conducted with a high extraction ratio, which leaves small pillars with a low safety factor in some old workings in abandoned mines. Pillar sloughage, squeezing or even collapse may have occurred in those old workings with small pillars, either at the time of mining or later. The conditions of the pillars in abandoned mines can affect mining above them. Subsidence fractures and abutment pressure are indications of multi-seam interaction caused by squeezing or collapse of small pillars. To mine over areas with potentially unstable small pillars, the panel layout in the upper seam should be such that multi-seam interaction can be minimized and proper roof and rib support should be installed in the influence zones. This case study presents an example of multi-seam mining above small pillars under a shallow depth of cover. Though the interburden is relatively thick and competent, interaction is still present over the influence zones. Pillar stability and multi-seam interaction analysis, numerical modeling and in-situ monitoring are presented to demonstrate how the upper seam can be mined safely over the small pillars.

Jan 1, 2014

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By E. S. Shaw

Utah continues as a very unimportant factor in oil and gas production. During the year 1933 there were no developments of noteworthy significance. There were no completions of either producers or dry holes during the year. The only commercial production in Utah has been from the five fields listed in Table 1 and mentioned briefly in the following paragraphs. Virgin Field.—Oil was first discovered in 1907 in a well drilled in sec. 13, T.41S., R.12W. Of the first 15 wells drilled, all but three were failures. In 1920 production from four wells from 550 to 600 ft. deep was about 20 bbl. per day. San Juan Field.—The majority of drilling in this area was done during the years 1908 to 1911. Probably the first commercial well in the field was that drilled in NW.$i sec. 6, T.42S1 R.l9E., in 1909. Farnham Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1923. A number of years later a second well was drilled by The Carbon Dioxice a mica1 Co., the present operator, which markets the gas in the manufacture of "dry ice" and allied products. The eslimated production, as indicated in Table 1, includes 500 million cubic feet estimated to have been lost while drilling the discovery well. Cisco Dome.—The discovery well was drilled by The Utah Oil Refining Co. in November, 1924. The Crystal Carbon Co. markets the gas in the manufacture of carbon black. Ashley Valley Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1925. The Uintah Gas Co. markets the gas in Vernal, Utah, for fuel. Woodside Structure.—In February, 1924, gas was discovered in a well drilled by Utah Oil Refining Co. in sec. 12, T.l9S., R.l3N., on the Woodside structure. This gas is reported to contain an appreciable amount of helium. It is being held as a helium reserve by the United States Government. Salt Valley Structure.—The test of the Utah Southern Oil Co. in sec. 31, T.23S., R.21E., on the Salt Valley structure has been shut down for some time at 6120 ft. This test has passed through more than 5000 ft.

Jan 1, 1934

By R. Taggart, J. W. Barton, G. R. Purdy, J. G. Parr

The constitution and mechanical properties of heat-treated alloys containing up to 10 pct* Ni in Ti have been investigated. The effects of quenching and of various isothermal treatments ale described, and C-curves are presented. The production of the precipitated and the martensitic hexagonal phases on quenching is discussed. MARGOLIN, Ence, and Nielsenl have determined the titanium-nickel phase diagram. A study of the transformations in gas-quenched and tempered powder specimens was made by Polonis and Parr.' Some isothermal transformation work was carried out by Margolin and ~unshah, who determined transformation curves for 4 and 6 wt pct alloys, while Robinson et al.investigated the formation of the w phase in a quenched and tempered alloy, Margolin and Bunshah showed that while a martensitic transformation could be obtained on quench- ing thin sections of a 4 wt pct alloy, a 6 wt pct alloy precipitated a nonmartensitic phase. The present investigation was undertaken to obtain more information on the transformations in quenched, quenched and tempered, and isothermally transformed lump specimens of alloys containing up to 10 pct Ni. Isothermal transformation curves have been determined for 7 and 10 pct alloys and cooling curves have been obtained for quenched alloys containing up to 7 pct Ni. The mechanical properties of 2, 5, and 10 pct alloys were studied, with the object of relating properties to microstructures. EXPERIMENTAL METHODS Alloys containing up to 10 pct Ni were prepared from sponge titanium and spectrographic standard nickel by levitation-melting and chill-casting in a split copper mold. The 5 and 10 pet alloys were prepared from sponge Ti having an as-melted hardness of 115 Vpn. The other alloys were made from a sec-

Jan 1, 1961

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth's surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex's findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983

By F. A. Champion

The work described in this paper was carried out in the Research Laboratories of the British Aluminium Company Ltd., under the general direction of A. G. C. Gwyer, Scientific Manager of the Company. In considering the effect of stress?corrosion conditions on metals, or the failure of metal through stress corrosion, it is evidently advisable to adopt a clear definition of the meaning of those phrases. There appears to be general agreement that stress-corrosion conditions may be defined as the continuous application of static stress to a metal while it is exposed to corrosive conditions, but recognition of the occurrence of true stress-corrosion in a metal is often a difficult matter giving rise to some confusion. For the purpose of this paper stress corrosion in a metal is defined as the acceleration of corrosion by the application of static stress. On this view it is necessary to test a metal not merely under stress-corrosion conditions, but also under the same corrosion conditions without the simultaneous application of stress, if the liability of the metal to stress corrosion is to be assessed. Failure of a metal under stress-corrosion conditions is sometimes quoted as evidence of stress corrosion (for example, by Althof(1)2), but this evidence is totally inadequate if the above definition is

Jan 1, 1945

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By F. Calizaya

This paper explains and discusses a computer program developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain project, Nevada.

Jan 1, 1994

By Paul Foote

The temperature of a material may be ascertained by measurement of the intensity of the radiant energy it emits. This measurement may refer to the radiation of all wave lengths emitted by the material, or, if the material is glowing, the measurement may refer to the visible light emitted, or to the radiation in n very restricted portion of the visible spectrum. In general, the intensity of radiation depends not alone upon the temperature of the source, but, also upon its nature. Thus, glowing carbon appears to the eye about three times as bright as glowing platinum, at the same temperature. This is technically expressed by saying that the emissive power or emissivity of carbon is about three times that of platinum. A material having the highest theoretically possible emissivity is known as a "black body;" it is customary to assign a numerical value of 1 to the emissivity of a black body. A black body is experimentally realized by uniformly heating a hollow enclosure and observing the radiation coming from a small opening in the wall. The intensity of radiation emitted from this opening depends only on the temperature of the walls, and not on the material of which they are constructed. If E is the emissivity of any non-transparent material and R is its reflection coefficient, it can be shown that E + R, = 1. If a material having an emissivity of, say, 0.40, and hence a reflection coefficient of 0.60, is placed inside a black body it becomes indistinguishable from its Surroundings, because the total intensity of radiation leaving the material is the same as that emitted by the black body. While the material actually emits only 40 per cent of the intensity of a black body at the same temperature, 60 per cent. of the radiation falling upon it from the walls of the enclosure is reflected. However, if the material is removed from the black body and placed in the open air, the reflected intensity is no longer present and the object appears but 40 per cent. as bright as a black body at the same temperature.

Jan 8, 1919

By J. J. Bodmer

THE four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following : 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

Jan 1, 1874