Search Documents

By J. W. Davis

The storage stability characteristics of a diesel type fuel were determined to evaluate the effect of the polar compounds in the fuel. These compounds, comprising most of the nitrogen and oxygen containing compounds and many sulfur containing compounds, were separated from the fuel with a chromatographic column. This fraction was further separated into three polar extracts by graded elution through the column. Each extract was characterized. A storage program using the depolarized fuel, the fuel as received, and blends of the extracts with both fuels, was conducted. Results showed that the removal of the more polar components stabilized the fuel. Blending the polar extracts with the original fuel and with the depolarized fuel in the same ratio as they existed originally and at two and three times the original ratio increased the amount of gum present before storage, but had little effect on the formation of additional gum during storage. Distillate fuels produced by commercial refining of petroleum contain traces of organic nitrogen, sulfur, and oxygen compounds that are more polar4 than the remainder of the fuel. Recent laboratory studies by the Federal Bureau of Mines (1),6 in which these compounds were removed from a fuel, have shown that they influence its storage stability. The objective of this work was to determine the amount of these compounds present in a fuel and their effect upon its stability in storage. To evaluate the role of these polar compounds, it is necessary to remove them from the distillate fuel. Many can be removed by chemical treatment (2), but such treatment precludes reblending the polar components to approximate the original fuel composition. Solvent extraction is free of some of the criticism of chemical treatment, but it is more difficult because of the complex mixture from which compounds must be removed.

Jan 1, 1961

By D. A. Stanley

Researchers at BCD Technologies and the University of Alabama have applied three statistical techniques to the information contained in a large database of measurements from a phosphate ore processing plant. The rust, Principal Components Analysis (PCA), replaces many measured variables with a few fundamental and un-correlated variables. The second technique, Projection to Latent Structures (PLS), is an extension of PCA that explores the relation between variables identified as either independent or dependent. The third technique, Cluster Analysis (CA), is applied to the results of the PCA or the PLS calculations, and identifies individual data clusters that represent uniform operating conditions in the plant. All three statistical methods can be seen as geometrical operations on the data viewed as points in space. A Viewer gives a corresponding graphical presentation of the data points. This paper describes the use of the above three techniques and the Viewer to explore part of the phosphate flotation database.

Jan 1, 1998

By A. G. Doll

"Multi-stage crushing plants, including high pressure grinding roll (HPGR) circuits, require more materials handling equipment than SAG and ball mill circuits. A temptation exists to neglect the energy consumption of materials handling when doing desktop comparisons of HPGR versus SAG milling circuits because estimation of materials handling power requirements can demand significant general arrangement drafting that is not available when performing preliminary scoping or ""desktop"" studies.The largest component of materials handling power is consumed by conveyors when lifting material between stages of crushing, meaning that a simple potential energy model can be used to evaluate conveying specific power consumption. This potential energy consumption for conveying can then be factored to provide overall materials handling specific energy consumption suitable for desktop studies of HPGR and other multi-stage crushing circuits. The technique also permits different crushing circuit flowsheets to be evaluated, at a preliminary level, by simply counting the number of times a conveyor must ""lift"" ore from ground level up to a bin or other equipment mounted up high.INTRODUCTIONTrade-off studies of multi-stage crushing plants involving high pressure grinding rolls (HPGRs) versus semi-autogenous grinding (SAG) mill circuits typically focus on the operating cost savings of crushing plants versus the capital cost savings of SAG mill plants. Very high-level (or desktop) studies of this type do not include a great deal of engineering work, meaning that the details (and costs) of ancillary systems are often not captured when doing the comparisons. The more complicated nature of the multistage crushing plants means there are more ancillary systems than a SAG mill plant, risking a skewed analysis of the operating costs, benefiting the HPGR option.One of the ancillary systems that may be overlooked is the more complicated conveying systems inherent in multi-stage crushing plants. Due to the mass of material being handled in large mining operations, these conveyors become a significant portion of the operating costs. A simple way to estimate the specific energy consumption of conveying systems without requiring engineering drawings and a site layout would allow high-level studies to capture this operating cost."

Jan 1, 2015

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

By Eugene Guccione

FOREWORD-In an interview published in the May 1975 issue of MINING ENGINEERING, one of the world's most respected scientists, nuclear physicist Hans Bethe discussed the reliability of nuclear power plants and their unmatched safety record. The Nobel laureate also refuted the anti-nuclear lobby's claims that nuclear plants emit harmful radioactive effluents. When asked whether the US has sufficient uranium resources, Dr. Bethe replied that "it depends on the time of introduction of the commercial and advanced breeder reactors which, in effect, can generate more nuclear fuel than they consume." The United States has enough U3O8 to last until the breeders can take over in 1995, said Dr. Bethe. But lie warned that extensive environmental damage would be caused if "environmentalists" succeed in delaying the development of the breeder. Any such delays, he noted, would vastly increase the demand for U3O8 in conventional reactors; this, in turn, would impose an immense burden on the US uranium mining industry, which would then have no alternative but to mine the low-grade Chattanooga deposits.

Jan 4, 1977

By Kan Xing

This paper introduces common detrimental consequences to the environment from mining in the Beijing West Mining Area. For example, ongoing mining operations can cause the following environmental deterioration: rock burst, roof rises, roof falls and inrush (Pit dash for ward water). Post-closure, after minerals resources are exhausted, the following environmental issues may remain: landslides (collapse, and mud-rock flow), dropping or exhausted water tables, water pollution, desertification and soil erosion, water accumulation, Slay endanger, ground subsidence, and causal factors in seismic activity. This paper analyzes this wide range of environmental consequences of mining, and offers a theoretical foundation to underpin a corresponding management scheme.

Aug 1, 2013

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

To counter depressed world nickel prices, a continuing effort is being made at Kalgoorlie Nickel Smelter to reduce unit production costs. One major area in which production costs can be reduced is the substitution of coal for fuel oil. Two areas where this has been achieved to bring about a saving are, the addition of coal to flash furnace flux to reduce supplementary fuel oil requirements in flash smelting and the replacement of two oil-fired air preheaters with a coal-fired unit. These actions have resulted in coal replacing 67% of the current fuel oil requirement in flash smelting at the Kalgoorlie .Lckel Smelter.

Jan 1, 1987

By Frederick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production Co., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenandoah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1-An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2-Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3-Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1952

By Gordon R. S. Smith

This paper is in two parts. The first part describes Membrane Back-Pulse Filtration and the effects of very short filter downtimes on cycle filtration rates. Part II describes the use of Membrane Back-Pulse Filtration for combined thickening and polishing soda ash thickener feed material followed by a description of computer modeling of CCD circuits by Iterative solver.

Jan 1, 1991

By K. J. Miller

A laboratory electrophoresis column was designed to separate pyrite from fine coal by utilizing an observed difference in the electrophoretic mobilities of the two materials in water. The apparatus worked well when tested with synthetic mixtures of coal and pyrite, but some modifications in design and procedure were necessary to provide a sharper separation. After these changes were made, the column was tested with a high-pyritic-sulfur raw coal sample. The column successfully fractionated the sample, removing not only the pyritic refuse, but a siliceous refuse as well. The invest ion demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis.

Jan 1, 1970

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By Felipe Farage David

A laminação de tiras a quente de bobinas de aço apresenta alta relevância devido a possibilidade de obtenção de diversos produtos para diferentes aplicações, tais como: construção civil, industria automotiva e implementos agrícolas. O controle das variáveis de processo, tais como temperatura de reaquecimento de placa, velocidade de resfriamento e temperatura de bobinamento, é determinante para obtenção da microestrutura e, por conseguinte, das propriedades mecânicas do material. O propósito desse trabalho é estudar o comportamento da microestrutura e das propriedades mecânicas com a variação da composição química (adição de microligas de nióbio e titânio), mantendo uma rota de laminação termomecânica similar na laminação de bobinas a quente. Os aços aplicados neste estudo foram o aço microligado ao nióbio e titânio equivalente ao ASTM A1018 HSLAS 50 Classe 1 e o aço carbono comum equivalente ao ASTM A1018 SS36 Tipo 2. Apesar do aço carbono comum apresentar carbono equivalente superior ao aço microligado, foi verificado maior limite de escoamento (se) no aço microligado ao nióbio e titânio. Dessa forma, aplicando tratamento termomecânico adequado no aço microligado é possível conseguir propriedades mecânicas melhoradas principalmente devido ao refino de grão e ao endurecimento da ferrita.

Aug 16, 2017

Inco Limited has been evaluating options for streamlining the overall flowsheet at its Sudbury, Ontario operations to improve productivity and to minimize the cost of at¬mospheric emissions reduction. Some of the flowsheets being considered include vari¬ous levels of copper/nickel separation at the Clarabelle Mill where all Inco's Sudbury Basin ores are processed. This paper reports on the laboratory and miniplant studies car¬ried out during the flowsheet development for a commercial Cu/Ni separation plant. There are two potential feed streams for Cu/Ni separation. It was determined that Cu/Ni separation from the rougher concentrate requires no regrind, and a very clean copper concentrate is produced, but the recovery of copper is limited to about 70% from ore. Cu/Ni separation is more difficult from the bulk concentrate because of the presence of excess flotation reagents in the slurry and due to locked particles. By replacing the slurry water with clean process water, and by addition of some hydrogen peroxide, entrainment is minimized and excess reagents are removed from the surface, providing a satisfactory separation of copper from nickel. Fine regrinding is required to increase liberation of the locked particles and to obtain 85% copper recovery with minimal nickel contamination of the concentrate.

Jan 1, 2005

By A. J. Basu

Rock mass properties testing for determining strength parameters is an integral part of geomechanics. These tests are performed either in a laboratory environment or in a field (in-situ). The authors share their experience in using numerical modelling in simulating the laboratory test procedures. This approach helps studying the rock breakage and failure mechanism more efficiently and provides a high degree of visualization. Moreover, imperfections and discontinuities can be easily incorporated in these models. This capability of providing arbitrary fractures and discontinuities facilitates in building a large knowledgebase of rock strength and failure mechanisms. This knowledgebase may then be used to generate heuristics for determining rock strengths for rock mass with fractures and discontinuities.

Jan 1, 1997

By L. T. Isaacs, W. H. Traves

A numerical model for analysing the drainage of fill in mine stopes has been described. The model can be used to analyse the process of fill drainage in existing and proposed mine stopes. The validity and potential value of the model have been established by experience with a simpler, 2-dimensional numerical model and by testing the new model against the earlier model. The new model is more useful than the 2-dimensional model because it allows for heterogeneity of fill material within the stope - a factor that has been demonstrated to affect drainage characteristics significantly. The 3-dimensional model is also capable of predicting pore pressures and drainage rates at specific locations in the stope without the need to resort to 2-dimensional generalisations. Such information, integrated with relevant field data as they become available, will provide valuable mine planning information for the scheduling of filling operations and design of fill mixes

May 1, 1991

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have b en available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on King available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have been available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on [king] available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By Yi Luo, FENGLIANG WU

Mine gob has long been a safety concern in the coal industry due to the air flowing through the gob area. Therefore, knowledge of the airflow distribution and locations of hazard zones in longwall gob is important to prevent and control these hazards. Due to the inaccessibility of mine gob, many numerical studies have been performed to simulate gob air leakage using computational fluid dynamics (CFD) programs, but most of the studies isolated the gob from the mine ventilation network (MVN) with only predefined pressure boundary conditions. The MVN is, in fact, not static in a dynamic longwall mining process, and it consequently changes the boundary conditions and the gob flow field (GFF). Therefore, the MVN should be incorporated in the CFD model to prescribe the transient boundaries. However, it is very challenging to couple the 1D MVN and the 2D/3D GFF to make the mine ventilation simulation realistic. This research uses a proposed novel finite tube method (FTM) to couple the MVN and GFF. In the FTM, the GFF is discretized into a finite number of flow tubes, each of which is formed by two adjacent streamlines. These tubes connect the MVN into a new coupling network. Based on the FTM, a model for gas migration in gob is established for delineating the hazard zones of explosive methane concentration and spontaneous combustion.

By W. L. Heidenreich

This report describes the methods and results of field investigations conducted by the Bureau of Mines between December 1956 and December 1957 on seven deposits of nickel-cobalt-iron-bearing laterite and weathered serpentine near the west coast of Puerto Rico east and south of Mayaguez. These deposits were named, for purposes of identification, Guanajibo, Punta Guanajibo, Las Mesas, north and south deposits of the Rosario Southeast group, and the west and east deposits of the Maricao Southwest group. In addition, the lower 17 miles of the Guanajibo River Valley was tested at widely spaced intervals for possible concentrations of magnetite and chromite in the alluvial sands. The objective of the investigations was to appraise, by drilling and sampling, the two largest deposits--the Guanajibo and Las Mesas. Testing of the smaller deposits was much more restricted. Field investigations consisted of mapping, drilling with power auger, sampling drill-hole sections, and pre-paring samples for chemical analyses, mineralogical studies, and metallurgical tests. The work was financed jointly under a cooperative agreement by the Bureau of Mines and the Economic Development Administration, an agency of the Puerto Rican Commonwealth.

Jan 1, 1959