Search Documents

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

Macraes Mining Company Limited operates a 2.1 million tonnes per annum gold processing plant at Macraes Flat, Otago. This uses a conventional CIL route to treat oxide ore, and a flotation, grind, CIL route for sulfide ore. This paper describes the design and operation of this process plant.

Jan 1, 1992

By A. J. Phillips, A. A. Smith, J. S. Smart

THE preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in properties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. PREPARATION OF HIGH-PURITY COPPER The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuS04-H2SO4 electrolyte using bagged anodes, low current .density (5 amp. per sq. ft.) and low temperature (25°C. max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe 2(S04)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then refiltered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2S04 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 434 by 43a by I-in anodes cast from high-quality electrolytic wire bar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars-which would result in fouling of the contacts and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By D Brett

The Paper presents the authors thoughts on how the mining industry should be improving the education of site personnel so they can provide a greater level of effective control of tailings dam safety including empowerment to develop their own documentation, monitoring and surveillance systems and to better liaise with specialist external technical staff or consultants.

Jul 1, 2021

By P. James

"INTRODUCTION Control of target stream pH is very important in leach mining and treatment of MIW (mining influenced water). On the production side, solution acidity can impact SX (solvent extraction) effectiveness through PLS (pregnant leach solution) and raffinate pH. Many older operations and legacy mining sites generate ARD (acid rock drainage) that is too weak for profitable metal production by conventional means and faces costly wastewater treatment for mitigation and disposal. For wastewater and environmental treatment, neutralization to precipitate and remove metal contaminants to clean the wastewater is the dominant approach. Traditional lime neutralization and precipitation is most often used but results in large amounts of mixed metal sludge requiring costly disposal. Blue Planet Strategies (BPS); which focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources, has developed a new “reagentless” neutralization process. Electricity is utilized in its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform capability to controllably raise target stream pH. The method offers a simple, low-cost approach yielding cleaner treatment chemistry. It can result in less sludge generation and enables possibilities to selectively recover contaminants as potentially saleable products for new revenue generation to offset further offset treatment costs. DEMET Overview BPS’s patented electrolytic DEMET platform leverages solid scientific and chemistry foundations through its advanced design to achieve capabilities and performance not previously realized. DEMET technology combines separated compartment electrolytic cell functionality with proprietary advanced dynamic electrodes and cell configurations to achieve a variety of chemistries and processing targets.[1-6] DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and more cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells."

Jan 1, 2015

By Herbert Everest

THE idea of economical production is usually associated with large operations, tonnages, and mines, with even larger capital behind them. Nevertheless many small mines operate in the shadow of large competitors and make a good showing on the capital invested despite larger overhead expenses. For the purpose of this discussion I will divide the cost of production into classes, and specify opposite each the approximate percentage expended thereon: 1. Labor, including miners and company men; 60 to 75 per cent. 2: Development, including all necessary yardage, room turning, crosscuts, etc.; 7 to 12 per cent. 3. Deadwork, covering payment to miners for handling falls, drawslate, or faults, rock work, water, and in general, all nonproductive labor; 3 to 7 per cent. 4. Supplies: mine timbers, oil, brattice material, lumber, cement, and repairs to equipment; 2 to 6 per cent. 5. Expense: management, selling, office, taxes, etc.; 1 to 5 per cent. 6. Depreciation of coal reserves and royalties; 6 to 10 per cent. 7. Depreciation of equipment and interest on capital invested; 1 to 3 per cent. 8. Fuel; ½ to 1 ½ per cent. The labor cost for a small mine is relatively much lower than for a large mine, particularly the sum paid to company men. Idle-pay expense is cut to a minimum; the labor item being larger than all the others together, a saving in labor makes a decided showing on the total cost. The development charges in small and large mines are about the same. There should be a small showing on the Beadwork item in favor of the small mine. The unit cost for supplies is usually small in the small mine. The operator of the small mine finds, owing to a limited tonnage, that the expenses of management, selling, etc., are abnormally high.

Jan 1, 1916

By A. C. Fieldner

"INTRODUCTION In a previous report3 prepared for the American Gas Association, the influence of washing coal on coke properties and on gas and by-product yields was discussed on the basis of answers to questionnaires sent to coke-oven superintendents and a review of the literature on the subject. This review indicated that the elimination of free impurities by cleaning coal improved coke quality by (a) reducing ash and sulphur, (b) decreasing clinker trouble in burning the coke, (c) diminishing cross fractures in the coke, resulting in greater resistance to breakage on handling, and less small coke and breeze, and (d) greater uniformity in chemical composition and physical properties of coke. Washing also reduced the sulphur in coke and gas and increased the yield of gas and by-products per ton of dry coal charged.This paper is supplementary to the previous report and presents some experimental data obtained with Pittsburgh bed coal from Pennsylvania and Mary Lee bed coal from Alabama.ACKNOWLEDGMENTSGrateful acknowledgment is made to F. J. Pfluke, of the Rochester Gas and Electric Cc., of Rochester, N. Y., for the plant test data on screened lump and washed coal; and to Ray W. Arms, Manager of the Coal Cleaning Department, of Roberts & Schaefer Co., of Chicago, for the data on effect of air cleaning."

May 1, 1931

By Michael Milstein

Northwest Research Station said as more and more older dams are removed to benefit fish, it’s become clearer that rivers rework themselves quickly.“Where the dam is relatively small, it’s a quick response,” he said. “The river quickly forgets.”

Jan 1, 2010

By Steven J. Schatzel, Kayode M. Ajayi, Bo H. Kim, Zoheir Khademian, Gabriel S. Esterhuizen

The stability of shale gas wells drilled through current and future coal reserves can be compromised by ground deformations due to nearby longwall mining. Depending on the longwall-induced rockmass permeability, the high-pressure explosive gas from the damaged well may reach mine workings and overwhelm the mine ventilation systems. This study uses geomechanical models to estimate the rockmass permeability induced by mining. A two-panel longwall model of a deep, 341-m-cover mining site in southwestern Pennsylvania is constructed in 3DEC to explicitly model the rockmass by a discrete fracture network (DFN) technique. Stress-induced fracture apertures and permeabilities are calculated across the model and are validated against permeability measurements. A fracture flow code (FFC) is developed to use these results to predict potential inflow to the mine should a gas well breach occur. One hundred DFN realizations are simulated, and the results show that for a gas pressure of 2.4 MPa, the average of the predicted inflow rates to this deep-cover mine is 0.006 m3/ s, significantly lower than the average inflow of 0.22 m3/ s for a shallow-cover mine (145-m deep) studied in the previous work (Khademian, et al. 2021). The result can help assess the potential hazards of a shale gas well breach for mine safety and evaluate the ventilation requirements to mitigate the risk.

Jun 19, 2022

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By J. D. Forrester

SINCE the introduction of the first percussion rock drill in about 1850, drilling equipment has undergone a progressive evolution so that a wide range of special classes of machines now are marketed by several manufacturers. Essentially all of the drilling machines presently employed for blasthole drilling are of the hammer-drill type. They are classified as hand-held hammers (jackhammers, sinkers, etc.), drifters (light or heavy), and stopers and are of many sizes; varying in weight and rotative and blowing power. Most makes of drill machines fundamentally are the same in principle of operation as they are designed to strike a blow on the end of a drill rod in the manner of early-day hand drilling. However, beyond this common characteristic, the similarity among different makes ceases. In choosing between similar machines of one make or another, it is important to remember that rock drill manufacturers have not attempted to standardize drill parts, the result being that a mine operator must approach, because of replacement parts, standardization by limiting the makes of machines used. The present-day selection of any particular drilling machine is dependent fundamentally on its inherent ability to make a hole, or series of holes, as speedily and as cheaply as is possible. Two categories of controlling elements become apparent in any analysis devoted to making the choice of a drill, namely: 1-Conditions under which the equipment is to be used, such as mining method practiced, type of labor available, character of rock material. 2-Physical characteristics or features of the given drilling machine. Regardless of the controls of class 1, above, the elements of this category are fixed by several factors. All of them are interrelated and, though some often are more important in one case than in another, an unfavorable variation of any-others being essentially equal-is sufficient to discredit the optimum applicability of the particular drill machine. The relative factors in the selection of a machine are as follows: First cost-This is not generally an important item on a comparative basis as the marketing of drill machines is highly competitive and most makes are priced closely.

Jan 1, 1952

By Carl E. Swartz

For many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011

By C. D. Rowe, H. S. Mitri, J. Malki, I. Vennes

Ore extraction at great depths creates high stresses around mine openings, which can result in violent rock failure in one of various forms of strainburst. This is especially true with strong and brittle rocks, which can store a large amount of strain energy that is suddenly released at failure. The strength and brittleness of rocks have been extensively investigated in the past. The most widely accepted method for the determination of rock burstability is the strain energy storage index obtained from a non-destructive uniaxial load–unload test. However, the results of this method are not always conclusive, showing less repeatability when the target test load is changed. This study concerns itself with the introduction of microscopic analysis as a tool to help validate the strain energy index results when burstability cannot be warranted based on mechanical property tests alone. In this study, two types of rocks, namely, basaltic komatiite (BK) and felsic norite (FNOR) obtained from Canadian underground mines are examined. The selection is based on the premise that felsic norite is known to be burstable from the mine experience, whereas basaltic komatiite is not necessarily burstable. A total of 60 mechanical properties tests were conducted including uniaxial compressive strength, Brazilian tensile strength, and load-unload tests. Laboratory tests on FNOR consistently exhibit high burstability; however, the results for the BK tests are not conclusive. To seek explanations for the mechanical rock behavior, 18 thin sections were examined with optical microscopy and image analysis. The findings show the tested BK specimens are dominated by alteration products, and all primary igneous minerals are lost. There is minor quartz, garnet, carbonate minerals, talc, and serpentine, which give the rock its ductile properties. The FNOR specimens are found to be relatively fresh and supported by a strong network of plagioclase with minor pyroxene, biotite, and secondary micas, explaining the higher stiffness. This study demonstrates how optical microscopy can complement mechanical property tests to evaluate burstability of rocks.

May 4, 2025

By Rasool Hejazi

The feed to Chadurmalu iron ore concentrator plant is a mixture of magnetite and haematite iron ore with a Fe/FeO ratio of about 8. The feed to plant, after grinding via wet SAG mill, is pre-separated by wet low intensity magnetic separator. Magnetic product is conducted to magnetite processing circuit for producing magnetite concentrate, and nonmagnetic product is directed to haematite processing circuit. Due to surface oxidization of magnetite particles and a decrease in magnetic attraction properties, significant amount of these particles are misled to tailing which results in decreasing the efficiency of haematite processing circuit. This problem can be remedied by using magnetic drum separator with more magnetic intensity and/or gradient. In this paper, the replacement of LIMS separators with wet medium intensity magnetic separators with a field intensity of 3800 gauss on drum surface (MIMS) have been suggested and considered as the most suitable solution to prevent the loss of magnetite particles. The results of carried out investigations with replacement of drum separators in industrial scale, showed that utilizing MIMS in magnetite processing circuit resulted in increasing final concentrate weight recovery on average by 2.59%, without any adverse effect on the concentrate quality; decreasing the magnetite content in the feed to high gradient magnetic separator (HGMS) by about 3.5%; decreasing the feed to floatation part by about 7% and consequently decreasing consumption of chemical reagents; increasing Fe/FeO ratio of the feed to plant. Keywords: iron ore, medium intensity magnetic separator, haematite, Chadurmalu

Sep 1, 2012

By A. V. Tarasov

A flow-sheet for waste-less processing of spent lead batteries comprises mechanized separation of batteries, smelting of the metallic fraction in a kettle, electrothermal smelting of oxysulfate fraction, refining of crude lead and processing of reverts to produce commercial products. Smelting of lead-containing fraction is performed in an electrothermal furnace using a processing technology developed in the Gintsvetmet Institute and differing from conventional processes by the fact that it does not require any fluxing agent (soda); no matte is formed in the process and the amount of slag produced is minimal, because its formation depends only on the ash content of coke and the quality of battery scrap separation. The process has been patented. It has been introduced on a commercial scale in 1.8 MVA furnaces at the plant of A0 "RyazTsvetmet" (Ryazan, Russia). The process has the following main advantages as compared with conventional shaft-furnace smelting and smelting in a short-drum furnace: the process does not require technical-grade oxygen, the amount of process gas generated is minimized ensuring a decrease in lead-containing dust and sulfur dioxide emissions by 3 to 5 times per unit of lead recovered; a decrease in dust entrainment resulting in lower amounts of recycled dust; lower slag yield (a decrease from 20-25% to 3-5%); lower coke requirement (a decrease from 10-14% to 3-4%). Refining of crude lead is performed using conventional technology but there are several unique features for which know-how is available. Processing of by-products of electrothermal smelting and secondary lead refining (slag, drosses, skimmings) and ebonite fraction (crushed battery casings) is performed in a slag-fuming furnace.

Jan 1, 2002

By Albert A. Munsch

The Munsch National First-Aid Instructors Association had its inception during the teaching of a Federal Bureau of Mines first-aid instructors' class at McPherson, Kans., under a cooperative plan of first-aid training. Upon completion of- the course on July 1, 1938 members of the class organized the charter chapter of the association under the name of McPherson (Kans.) District Charter Chapter No. 1. On July 1, 1941, 3 years after the founding of the association, there were 15 chapters in the national council -7 in Kansas, 3 in Oklahoma, 2 in Texas, 2 in New Mexico, and 1 in Arkansas. Although the pioneer work of the association was done in the petroleum industry, the plan will be of even greater benefit to a district in which there are various types of plants, mince, and operations of the mineral and allied industries. ACKNOWLEDGMENTS The writer appreciates the cooperation and assistance of the following persons: S. P. Redfearn, safety engineer, Globe Oil & Refining Co. and affiliated companies, Wichita, Kans., and H. (Chief) Moore supervisor of safety meetings, Shell Oil Co., Inc., McPherson, Kans., for their untiring efforts and enthusiasm in organizing an- attending the first class, organizing three other classes, and helping to plan the work of the association

Jan 1, 1942

By Adriana A. S. Felix, Julio C. Afonso, Luiz C. Bertolino, Bruna L. Novo, Fernanda A. N. G. Silva, Karla M. A. Simões

Palygorskite (Mg,Al)5Si8O20(OH)2(OH2)4.4H2O, is a lamellar mineral with a fibrous morphology. The micropores and canals in the structure give a high specific surface and sorption capacity of various kinds of species. Guadalupe’s palygorskite (Piauí/Brazil) run of mine (ROM) was prepared (PA) and characterized by XRD and XRF. PA is composed by palygorskite, kaolinite, quartz and goethite and has 15.8, 58.0, 4.2 and 7.6% of SiO2, Al2O3, MgO and Fe2O3, respectively. Wet magnetic separation tests were conducted with PA obtaining the magnetic and non-magnetic fractions (PAM and PANM, respectively). PANM was characterized by XRD and XRF and the results of the XRF indicated that the iron content in the PA decreased 8.0% in the non-magnetic product. A new wet sieving was conducted with PANM to obtain a purer fraction (−20 μm) (PANMP) which was characterized by XRD, XRF, CEC, Zeta potential, SEM, TG/DTG. The result showed that this mineral could be used as adsorbent of heavy metals.

Mar 1, 2017

By T. O. Massalski, J. D. Ayers

A massive transformation, 0 —am, takes place in a number of copper-based systems where the ß phase field at high temperatures extends to compositions that are slightly less solute-rich than the limits of the a phase field that exists at lower temperatures. Consequently a solid-state transformation becomes possible that does not involve a change of composition. Within this narrow range of composition the massive am phase can be usually produced in two ways: by a fast quench from the ß phase through the a phase field, or by pulse heating into the a phase field of an undecomposed ß phase retained at room temperature by a prior quench. In the Cu-Ga system the occurrence of a massive am phase has been also observed in alloys whose composition falls outside the equilibrium a phase field1 but not in the Cu-Zn system.2 We have recently observed the occurrence of the ß — am transformation also in two silver-based systems, Ag-Zn and Ag-Cd. The a and 0 phase fields in these systems again slightly "overlap" in a narrow composition range. In the Ag-Zn system this range falls between 36.7 and 40.2 at. pct Zn, and in the Ag-Cd system between approximately 41 and 42.5 at. pct Cd. Alloys were prepared from high-purity materials and cast in quartz tubes under inert atmosphere. No significant change of composition occurred during casting. After homogenizing in the 0 phase field, small pieces of each alloy were reheated at the homogenizing temperatures for a few minutes and quenched into various media. There were examined metallographic-ally after removal of surface layers that may have suffered from contamination or from the loss of the solute element. In the Ag-Zn system extensive areas of the am phase (identified by selective etching, observation of the slip trace variants, and occurrence of twinning) were observed in a comparatively low-zinc alloy (37.8 at. pct Zn) for all quenching media employed: iced

Jan 1, 1969

In 1955 the annual production of steel at Australian Iron and Steel Pty. Ltd., Port Kembla was 1.2 million tonne and over the following two decades this had progressively increased to the present capacity of 5.4 million tonne per annum. This increase in productivity has also been accompanied by important developments in steelmaking technology and these are explained in the chronological order in which they have taken place. Reference is made to the use of oxygen in open hearth furnaces, the B.O.S. process, the Argon-Oxygen decarburisation process for stainless steel, vacuum degassing and continuous casting. When the vacuum degassing and continuous casting units are commissioned, the Port Kembla Works will have achieved a standard of steelmaking technology equal to any in the world.

Jan 1, 1976