Search Documents

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

By E. V. Mezentseva, S. M. Okunev

"In the article there is set forth a development experience of JSC LEBEDINSKY GOK Beneficiation Plant concerning the plan of increase in the production volumes of the iron ore concentrate with Fe content more than 69.5%. There are considered the issues regarding implementation of the updated process scheme of the concentrate beneficiation using fine screening operation, its industrial tests have shown an exploitability of this development direction. There are described the issues relating to the ceramic filters for dehydration of the additionally-beneficiated concentrate, there are given the production and process figures achieved during the exploitation. The methods of the research. In the paper there have been used the following scientific research methods: the methods of system analysis, mathematical statistics, classification, comparison, modelling, observance, experiment. INTRODUCTION JSC LEBEDINSKY GOK is the largest leading enterprise for iron ore beneficiation and the unique RF producer of the merchant hot briquetted sponge iron (HBI) highly demanded by the consumers. Raw materials for hot briquetted iron production are fluxed pellets produced from iron ore concentrate with Fe content more than 69.5% (additionally-beneficiated concentrate). Strategic program of the plant’s development foresees expansion of production of the highly demanded products that imposes a necessity of expending capacity of the enterprise and implementation in production of modern processes and equipment having low resource intensity and ensuring in addition a high efficiency. Construction of the third stage of the HBI Plant became one of directions for the strategic development of JSC LEBEDINSKY GOK implemented in 2017 that caused a demand in the production volumes and filtration of the iron ore concentrate with Fe content more than 69.5%. Purpose of the work – to develop and to provide a rationalization for efficiency of the production process and filtration of the iron ore concentrate with Fe content more than 69.5% ensuring increase of production volumes and its prime cost."

Jan 1, 2018

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

[A discussion suggested by the paper of Mr. James Gsyley on " The Development of American Blast-Furnaces," read at the New York meeting of the Iron and Steel Institute, October, 1890, and reprinted from the Journal of that Society in Bans. A. I. M. E., xix., 932.1 (Cleveland Meeting, June, 1891.) [Kote by the SecretaRy.—The three following contributions to this discussion were communicated by letter to the Secretary of the Iron and Steel Institute, and were received by me too late for insertion in vol. xix. of the Transactions.] FRed. W. Gordon, Philadelphia, Pa.: Mr. Gayley's paper calls our attention to the very expensive blunder hitherto made in blowing too much wind in a given size of furnace. It was quite evident from an analysis of blast-furnace operations that the work we are doing in America is anything but creditable. We were consuming fully 1000 pounds of coke more than is necessary for each ton of iron made, and were hammering the linings of our furnaces out in a very short time, and nothing but the very high price of pig-iron would stand the drain. It had long been my pet scheme to gradually reduce the quantity of air, at the same time increasing the burden to the maximum and decreasing the limestone, and determining, if possible, the fuel economy which might be reached consistently with the maximum production of the furnace. After the success of the Isabella furnace at Pittsburgh, which was remodelled in 1880, the North Chicago Rolling Mill Company had

Jan 1, 1892

By AIME

Cores must be cut in half to secure workable samples for saturation, porosity, and permeability tests. They come from the field labeled as to the type of core, well, and depth from which they came.

Jan 1, 1948

By W. E. Cobb

The financial implications of environmental liabilities are becoming staggering, particularly for mining companies. The Environmental Protection Agency's (EPA) Record of Decision (ROD) list for Superfund mining sites has some pretty hefty financial commitments, such as the $10 million operable unit remedy for the Yak Tunnel at California Gulch (in Colorado) or the $40 to 60 million remediation at Bunker Hill (in Idaho). These costs are driven by the large volume and areal extent associated with historical waste management practices at mining sites. (It's difficult to have a low-cost remedy for a 20-square-mile site.) Unfortunately, there are other ways of generating environmental liabilities besides Superfund, such as non-compliance with Clean Air Act provisions, stormwater permits, or National Pollutant Discharge Elimination System (NPDES) permits. In the last 2 years, EPA has increased enforcement in its regulatory programs, which has resulted in increased fines and criminal actions. Leaders in other industries (primarily the chemical and manufacturing industries) are viewing environmental liabilities as a strong motivator to select engineering approaches carefully based on technical, legal, economic, and philosophical perspectives. Industry interest in waste minimization programs comes from the concept that it is economically advantageous not to create waste in the first place. Waste minimization programs typically balance increased front-end capital investment with the minimization of potential long-term environmental liabilities as a way to achieve the lowest total-or life-cycle-cost. A side benefit of waste minimization programs is that they tend to improve overall regulatory compliance. Waste management practices are also becoming philosophical, as evidenced by a May 11, 1992, Business Week article: Companies that incorporate innovative thinking on sustainable development will do more than clean up or prevent their own pollution. They'll make and distribute a product more efficiently than ever, worry about its lifelong environmental impact, plan for recycling, and get their suppliers on the bandwagon. This type of approach will require a new mind-set, new tools, and adjustments throughout the organization. A key aspect of waste minimization or life-cycle waste management programs is the incorporation of environmental costs into economic analyses that compare various waste management alternatives. However, the incorporation of environmental costs into an economic analysis can be more difficult than initially thought. As noted above, new tools-or even a new toolbag-are needed, such as new accounting methods that track and assign the true lifetime environmental costs of a particular product. One piece of the new toolbag is life-cycle cost analysis, which is discussed in this paper. To simplify the discussion, this paper looks at the total costs associated with a given mining site. The concepts presented in this paper, however, can be applied to any mine waste management decision. The ultimate extension of life-cycle costing, as presented in the Business Week article, is to include the potential environmental costs throughout the life of a metal. At this point, I am perplexed on why, let alone how, to include the potential downstream environmental costs (i.e., the costs associated with smelting, manufacturing, use, and recycle or disposal) throughout the life cycle of mined copper, lead, or zinc.

Jan 1, 1992

By H. C. Voges

An account is given of the tests being conducted by Iscor on the following processes for the beneficiation of coal fines: froth flotation, gravity separation, heavy-medium separation, and pneumatic and column flotation. The coals used in the tests came from the Durnacol, Tshikondeni, Grootegeluk, and Hlobane collieries. The problems involved in the dewatering of fine products are stressed. From a theoretical study of the efficiencies that should be possible for a hypothetical South African coal, it is concluded that future fines-beneficiation plants in South Africa may use standard heavy-medium cyclones for coal down to 1 mm in size, fines heavy-medium separation for the 1 mm to 450 µm fraction, and column or pneumatic flotation for the minus 450 µm fines.

Jan 1, 1991

INTRODUCTION This paper was originally presented at the Platinum Adding Value Conference, held at Sun City from the 4th to 6th October 2004. Narrow reef mining may not be applicable to the base metal operations in Zambia, however, it is considered that the methodology used is equally appropriate to the development of technology and mining methods in mining environments other than narrow reef mining. The purpose of this paper is to explore the integration of technology and stoping systems. For the last hundred years the South African narrow reef mining industry has battled to control working costs in a labour intensive industry. It is only through the application of appropriate technology that change will occur. Stoping systems, because it is the stoping method and methodology that is at the heart of the mining system. Introduce a different technology that results in a more efficient stoping system and the mining system will look after itself. The technology applied to stoping in narrow reef mining, over the last 100 years, can be categorised as follows: ? The introduction of pneumatic rockdrills early this century. The cumbersome rig mounted units being replaced by smaller, lighter, hand held units that were then made easier to use with the addition of an air leg. (The so called Swedish method of mining.) As late as the early 1970s some drilling was still being carried out without the assistance of an air leg. ? Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s. ? Hydraulic props installed close to the face and capable of applying force against the hangingwall as well as yielding in a controlled manner under dynamic load arrived in the 1960s. In many instances these have now been replaced by yielding elongates fitted with water hydraulic tensioning devices. ? Some people argue that the introduction of tungsten carbide inserts, to improve drilling, was equally important.

Jan 1, 2005

By V. I. Lakshmanan, I. G. McColl

"Heap leaching of gold ores in permafrost conditions is feasible provided certain criteria are met. These criteria include relatively short heap leach residence time and the availability of waste heat.This paper describes the conceptual design of such a system for a mining operation in the North West Territories of Canada. The design includes the concept of continuous countercurrent leaching in enclosed ore heaps.Indicative capital and operating costs are given.INTRODUCTIONIn April 1984, Acres Davy McKee Engineering Inc. (ADM Eng.) in association with Ontario Research Foundation (ORF), was invited to carry out a preliminary design, cost estimate and financial analysis to assess the viability of gold heap leaching in a permafrost region in North West Territories, Canada.An orebody was being explored which could, by nature of its mineralogy, be upgraded substantially by crushing and screening in the size range of 1/4 in. to 3/4 in. It was proposed to process the screen undersize through an existing gold mill on site and to treat the oversize material in a heap leach facility to be constructed adjacent to the existing mill.Despite the formidable challenges imposed by isolation, permafrost and harsh winter conditions, the heap leach project was considered worthy of examination because of the relatively high grade of the heap leach material (> 0.1 oz/ton), very short leach times (in the range of 1 to 4 days) and the availability of substantial quantities of waste heat from the diesel generating station on site.Design challenges included the necessity to maintain the permafrost in frozen condition, to prevent freezing of ore and leach solution, to limit size of construction materials to that which could be carried in a Hercules freight plane and to contain water usage at an absolute minimum level."

Jan 1, 1987

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By M. A. Usman, E. I. Akpan, S. O. Adeosun

Preliminary studies on the extraction and characterisation of biodegradable lignin from palm oil fruitbunch (POFB) for carbon fibre production has been conducted. Centra lComposite Design was used to determine the optimum operating conditions for maximum yield and properties of the extracted lignin. Soda concentration (1–3 wt/vol%), temperature (50–90 °C) and reaction time (20–30 min) were analysed using Rcore software. Experimental results show that using reaction temperature of 90 °C, time of 30 min and 3 wt/vol% soda concentration yields 3.3 g of lignin from 30 g of the POFB. The path of steepest ascent from ridge analysis shows that with temperature of 130 °C, time of 40 min. and soda concentration of 3. wt/vol%, 8.7 g of lignin can be extracted from 30 g of POFB. Analysis of FTIR and SEM show that the lignin has the same structure in all cases with minimal impurities.

Mar 1, 2017

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By Frederick M. Becket, Russell Franks

WideSpread experimentation has been conducted in recent years to devise a means of preventing intergranular corrosion in austenitic chromium-nickel steels of the 18 per cent chromium-8 per cent nickel type. Additions of titanium to these steels have been used commercially to overcome this dificulty, as advocated by Krupp of Germany, and the latest literature reference concerning improved details of this method is the article by Bain, Aborn and Rutherford.' Extensive work by the present authors has shown columbium also to be a particularly valuable agent for inhibiting intergranular corrosion. This paper does not deal with steels that are largely or wholly austenitic; it is limited to a discussion of the results obtained through the use of titanium and columbium in plain high-chromium steels. For many years titanium has been used commercially by some steelmakers as a cleanser, and to a lesser extent as a hardener, but then in greater percentages. The results of the work to be described disclose that titanium and columbium in proper Proportions act as effective softeners in the high-chromium steels. It is well known that chromium intensifies the hardening effect of carbon in steel; it imparts pronounced air-hardening properties within a rather wide range of chromium content; it provides increased ductility in steels of given strength and hardness; and it enhances resistance to corrosion and oxidation at elevated temperatures to a marked degree. However, in applications requiring a combination of some of these valuable properties great hardness is frequently a detriment rather than a merit. When the objective is a soft and ductile steel having optimurn corrosion resistance, the producer strives for a carbon content as low as commercially practicable. Despite these efforts some of the commercial high-chromium steels low in carbon present considerable difficulties during production, owing to their air-hardening properties, and in consequence the economic result is not favorable. A good example is found in the 5 to 6 per cent chromium steels employed chiefly in the oil-cracking industry. Sleels

Jan 1, 1934

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for disposal of transuranic waste and is operated by the US Department of Energy. The repository is located at a depth of 655 min the Permian age salt beds of the Salado Formation. The exhaust air from the facility is independently monitored by the Environmental Evaluation Group to verify compliance with regulatory release limits for radioactive materials. A May 1995 video inspection of the exhaust shaft identified fluid migration into the uppermost 25 m of the shaft. Since then, water has been observed flowing in from cracks in the shaft lining between 16and 25 m below surface level at an estimated rate of between 5 and15 m3/d. This water inflow has not only negatively impacted the equipment in the shaft, associated duct-work and monitoring equipment located at the top of the shaft, but also challenged efforts to verify compliance at the WIPP. This paper provides an analysis of these effects.

Jan 1, 2004

By G. Trusler, P. Dama, C. Buckley, C. Jänisch

In the 1990s, Cleaner Production (CP) approaches were successfully introduced to a number of industrial sectors in South Africa. Building on this success, the South African Water Research Commission has commissioned a 3-year study to investigate the use of CP and its related set of environmental assessment and management tools in the mining industry. A scoping study is being carried out on the current knowledge of CP approaches being used in the industry, as well as the proactive and preventative measures being undertaken. One of the significant findings of the scoping study is that distinct differences exist between the larger global companies and the smaller local companies. Being a water research project a key focus area of the project is to reduce the impacts related to mining on the South African water resources. Some of the significant water related threats identified include acid mine drainage, the shortage of the resource and the effects of inter-mine flow.

Jan 1, 2005

By Corby G. Anderson

"Laboratory testing, plant optimization, and the interpretation and application of metallurgical technologies can be tedious, time consuming and costly. This paper outlines the use of proven statistical design of experimentation software for rapid laboratory testing and optimization of operating plants with limited representative sample utilization. This results in less costly required testing, a more thorough understanding of results and the ability to simultaneously optimize several variables and outcomes at once. At the Center for Advanced Mineral and Metallurgical Processing (CAMP), this testing methodology has been used successfully in many metallurgical development and plant optimization projects thereby confirming its real world utility and application. Accordingly, several applied examples in flotation and hydrometallurgy will be outlined in this paper. This will include flotation testing of a copper gold ore, flotation testing of a copper, cobalt and gold ore, optimization of an industrial hydrometallurgical jarosite circuit and optimization of industrial nitrogen species catalyzed pressure leaching of a copper enargite concentrate.INTRODUCTIONWhile flotation technology is now 100 years old, the testing, interpretation and application of lab results can be tedious, costly and time consuming requiring extensive sample collection and preparation. In addition, recent applications like hydrometallurgical pressure leaching and associated unit operations, such as precipitation, still remain more of an art than a quantifiable science. This paper will elucidate the application of STAT-EASE Design-Expert software to minimize required laboratory testing while rapidly optimizing multiple results and outcomes in a statistically valid manner. The STAT-EASE program is based on proven design of experiment fundamentals. In this paper, the real world application of this methodology for lab testing, plant optimization and process development will be elucidated."

Jan 1, 2006

By Lanre Oshinowo

The trend in process engineering is to design compact, more efficient processes, there is the paramount requirement to get the job done right the first time going from the drawing board to full-scale commercial operation. To accomplish this goal, there is also the need for tools beyond the traditional engineering toolkit to evaluate designs through virtual prototyping, thereby reducing the risks associated with making design decisions. One of the most important tools that has recently come to the forefront of process design and development is Computational Fluid Dynamics (CFD). CFD has been used at HATCH to address the key process parameters that drive the design of hydrometallurgical unit operations. This paper will detail the role of CFD at HATCH in achieving a superior level of confidence in the process design of autoclave circuits. Specifically, the optimum application of multiphase modeling including hydrodynamic, heat and mass transfer to hydrometallurgy operations, the impact of non-Newtonian slurry rheology on autoclave performance, and the challenges of optimizing the mixing of key reactants into slurries in autoclave reactors, is discussed.

Jan 1, 2003

On Feb. 16, 2012, the Polish coal mining company Lubelski Wegiel Bogdanka S.A. set the world record for daily production from a plow-equipped longwall, with an output of 24.4 kt (26,900 st) of coal from a single face. The company commissioned the first Cat longwall system at its Bogdanka Mine, near Lublin in eastern Poland, in March 2010 and within six months had raised the bar to nearly 17 kt/d (18,700 stpd) of cut coal. Since then, Bogdanka has continued to increase its daily output with a plow face that began mining in the new 7/VII/385 panel last October, taking the world record to new levels. In addition to the record output achievement, the plow face advanced more than 27 m (89 ft) at a 1.63-m- (5.3-ft-) cutting height. ?We thought this achievement would be impossible for any shearer in seam heights as low as this,? said Zbigniew Stopa, vice president of Bogdanka.

Jan 1, 2012

By D. Turk, P. Lefebvre, J. Sargent, K. Major

"Stillwater Mining Company recovers platinum and palladium from their Nye Montana operations. Mining first commenced at Nye in 1987 at a milling rate of 455 t/d (500 stpd). The plant was expanded in 1995 with the replacement of the ball mill and the addition of flotation capacity to increase mill throughput to 1820 t/d (2000 stpd). The applications for platinum and palladium have increased in recent years particularly in the automotive industry and the supply of the metals has remained fairly constant with prices for both platinum and palladium increasing and remaining very stable. In 1997 Stillwater initiated the expansion of their operations to increase production of platinum and palladium. Projects were initiated to expand production at the Nye operations, increase smelter and refining capacities at the Columbus facilities and to develop the extension of the orebody at the East Boulder site. This paper will discuss the changes at the Nye concentrator which were completed to increase production from 1820 t/d (2000 stpd) to 2730 t/d (3000 stpd) and eliminate some of the process bottlenecks.IntroductionStillwater Mining Company is mining the only significant primary source of PGMs outside of South Africa. The J-M Reef is an extensive mineralized zone containing PGMs that has been traced over a strike length of about 43 km (27 miles) in the southwest region of Montana. Stillwater controls the entire PGM mineralized zone.Johns-Manville geologists discovered palladium and platinum in the early 1970’s. In 1979, a Manville subsidiary entered into a partnership with Chevron, USA to develop the project. In 1 987, operations at the Stillwater property near Nye, Montana commenced."

Jan 1, 2000