Search Documents

By L. A. Roe

Calcium carbonate and talc fillers both find use in a multitude of Industries. Each filler has many commendable properties, and often compete for the same market. Quality controls for various grades are exacting and complicated. A detailed comparison of the physical and chemical properties of these two fillers is tabulated and the mining and processing of the ores is described.

Jan 1, 1980

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By F. Rosenblum, P. Cancilla

The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automatic control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool. A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic¬based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the "wish list" of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight utilizing uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content.

Jan 1, 2002

By Marcus Grossmann

THIS paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, 'the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of Chromium, Per Cent FIG. 1.-IRON-CARBON DIAGRAM. FIG. 2.-IRON-CHROMIUM DIAGRAM. alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron.

Jan 12, 1926

By Junto Nishiwaki, Shinji Kumai

"Mechanical and physical properties of the impact welded dissimilar metal joints are controlled by joint interface morphology. An intermediate layer (IML) is often formed at the joint interface and this deteriorates the interface quality in some metal combinations. Numerical and experimental studies were performed in order to examine the formation mechanism of the wavy interface and intermediate layer for explosive welded Al/Cu dissimilar metal joints. The impact welding process consists of (1) high-speed oblique collision of metal plates, (2) metal jet emission and large deformation and temperature increase at collision point and (3) rapid cooling at the joint interface. Euler-Lagrange coupling method, smooth particle hydrodynamic (SPH) method and modified laplacianFoam (LF) method were linked together to simulate a series of processes from (1) to (3), and the final interface morphology including the formation of IML was reproduced. The wavy morphology (wave-height, wavelength) and the position and composition of IML formed at the joint interface of Al/Cu joints were quantitatively in good agreement with those reproduced by numerical analysis. Our simulation results are useful for the control of the interface morphology, reduction of the amount of IML, and improvement of the mechanical properties of the impact welded dissimilar metal joints.INTRODUCTIONImpact welding is a kind of solid state joining method providing extremely high joint strength for both similar-and dissimilar metal combinations. Explosive welding and magnetic pulse welding are representative methods to achieve the impact welding. By a high-speed oblique collision between two metal plates, a metal jet is emitted from the collision point. The metal jet can remove any oxide films and contaminations on the plates and produce an active refreshed surface. Consequently, good metallurgical bonding can be achieved even for dissimilar metals (Crossland, 1982). Solid metals deform like fluids under the high pressure condition at the collision point and characteristic wavy interface is formed. In addition to the wavy interface, an intermediate layer (IML) is often formed at the joint interface in some metal combinations. Elimination or reduction of the amount of IML at the joint interface is desired since the excessive IML formation along the joint interface causes a large reduction in physical and mechanical properties. Formation of IML is considered to result from characteristic thermal history at the joint interface including partial melting due to the local temperature increase and successive rapid cooling behavior at the joint interface. In order to control the IML formation at the joint interface, it is necessary to reveal both heating and cooling processes at the joint interface. However, it is impossible to observe the phenomenon occurring at the joint interface and also difficult to investigate the temperature change at the joint interface directly during the impact welding. Therefore, simulation or numerical analysis is indispensable to overcome this problem. In the present study, the explosive welded Al/Cu joint, which is prone to form IML at the joint interface, was selected for the research. By using a newly developed numerical analysis method, not only the formation process of wavy interface, but also the local temperature increase and successive temperature decrease at the joint interface were reproduced. The formation process of IML was investigated by using both numerical analytic and experimental results."

Jan 1, 2018

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

During dusk, nighttime and dawn operations, effective illumination is a crucial component of safety for getting on/off mobile surface mining equipment and for preshift inspections. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers examined whether illuminance levels could be improved for ingress/egress systems and preshift walkaround inspections of equipment using light-emitting diode (LED) area luminaires. Illumination and glare were key metrics evaluated. Although headlamps provided adequate illumination, LED area luminaires illuminated a much broader area compared to the narrow spot lighting of the headlamp. Hence, the use of additional area luminaires can increase slip-trip-fall (STF) hazard awareness and detection. Furthermore, a commercially available luminaire demonstrated better results than a custom LED luminaire relative to discomfort and disability glare.

By G. Koves

The behavior of case-hardened AISI C-1213 free -machining steel under complex impact-fatigue -wear load conditions was investigated. The inherently poor dynamic properties of the steel are mainly affected by the stress distribution in the case, component shape, and tempering. Cold-riveted components showed unexpectedly high dynamic strength compared to basic parts. A compromise beatment—which provides good dynamic properties, reasonable wear resistance, and fair riveting characteristics—zuas developed. A number of mechanical components in data-processing machines are made of free-machining carbon steel. Although, selected primarily due to manufacturing requirements, components made of these grades frequently undergo complex heat treatment and must sustain impact-fatigue loads. A typical free-machining steel is the AISI C-1213 grade, which is a resulfurized and rephosphorized open-hearth steel. While the undesirable effects of sulfur and phosphorus on the mechanical properties are well-known, data on dynamic properties are scarce.1"3 Rapid rotating or oscillating motion while carry- ing a high cyclic load requires a combination of wear resistance with high endurance limit and impact toughness. The inherently poor dynamic properties of the free-machining steel are further degraded by the machining, which introduces local stress-concentration areas. While the heat treatment (usually case hardening) improves some mechanical properties, it necessarily impairs others. Another problem arises when components, such as studs, must be fastened by riveting. The high crack-sensitivity of the free-machining steel, especially in the presence of a hardened case, makes this operation difficult. In view of the preceding considerations, it is of interest to investigate the behavior of a typical component under complex impact-fatigue-wear loading conditions in order to explore the effects of material, machining, and heat treatment, to obtain specific data on the dynamic characteristics of free-machining steel, and to arrive at a process which would adequately utilize the inherent qualities of this material. EXPERIMENTAL PROCEDURE To simulate actual service conditions, a typical component was selected, based on frequency of application, complexity of load, and processing difficulties. The dimensions and shape of the component—a stud used in many electromechanical document-handling machines—are shown in Fig. 1.

Jan 1, 1964

By Manuela Castaneda, Henry A. Colorado

This paper is about the use and stabilization of iron oxide based powders with arsenic contents coming from the purification of water. Cement paste samples with 0.0, 2.5, 10 and 20wt% of waste were fabricated by mixing mechanically all components. There are two main positive impacts of using this waste, first, this waste is produced in large amounts worldwide, and therefore the stabilization has a significant impact for the environment. Second, the waste can be used as an admixture and filler for cement, and therefore reduce the amount of cement in the concrete, which has a major impact in the CO2 footprint since cement industry produces a lot of this gas. Compressive strength and density tests were tested after 28 days. Microstructure was analyzed with scanning electron microscopy and x-ray diffraction. Results show that compressive strengths greater than 20 MPa were obtained and the samples had calcite, portlandite and ettringite phases.

Mar 1, 2018

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By I. Campbell, P. C. Jones, E. G. Potter, R. P. Taylor

"The Cobalt embayment is a large domain of Paleoproterozoic clastic sedimentary rocks that unconformably overlies the Archean Abitibi greenstone belt. Regionally extensive sills and dikes of Nipissing diabase, emplaced circa 2219 Ma, occur throughout the embayment and are the preferential host to gold-bearing polymetallic vein systems on the Merico-Ethel property, near the northeastern margin of the Cobalt embayment. These gold-bearing, polymetallic veins are predominantly east-west-trending, steeply dipping, discordant calcite- quartz vein systems that formed close to the time of crystallization (within ~15 m.y., based on Pb-Pb ages) of the Nipissing diabase. The ore mineralogy is complex in character, typically comprising sulfides, arsenides, native metals (gold and silver), and specular hematite, preferentially concentrated along the interface between silicate and calcite gangue. A simplified sequence of mineral deposition in the veins is: (1) "Early-stage" pyrite ± chalcopyrite hosted in quartz ± chlorite gangue; (2) "Main-stage" polymetallic (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U) sulfides, arsenides, and native metals hosted in calcite gangue; and (3) "Late-stage" calcite flooding ± galena. Wall-rock alteration in Nipissing diabase is restricted to narrow (<5 cm) haloes of calcite-chloriteepidote- bearing assemblages, whereas a weak alteration halo of specular hematite, calcite, and allanite-epidote has been observed in the surrounding sedimentary rocks. In terms of their age, geology, mineralogy, paragenesis, and morphology, the gold-bearing vein systems at Merico-Ethel closely resemble the silver-sulfarsenide vein deposits of the historic Cobalt and Gowganda mining camps. These observations indicate that the Au-bearing veins are variants of the Ag-vein systems and as such, have a common genesis belt. L’Échancrure de Cobalt est un large domaine de roches sédimentaires clastiques d’âge Paléoprotérozoïque qui reposent en discordance sur la ceinture de roches vertes d’Abitibi d’âge Archéen. La Diabase de Nipissing, mise en place vers 2219 Ma et qui constitue un réseau de sills et de dykes d’importance régionale, est présente dans l’ensemble de l’échancrure et constitue la roche-hôte principale des systèmes de veines aurifères-polymétalliques de la propriété Merico-Ethel, près de la bordure nord-est de l’Échancrure de Cobalt. Ces veines à minéralisation aurifère et polymétallique constituent un système de veines de calcite-quartz sécantes d’orientation principalement est-ouest et à pendage fort qui se sont formées peu de temps après la cristallisation de la Diabase de Nipissing (à ~15 Ma près, d’après les âges Pb-Pb). La minéralogie de la minéralisation est complexe; elle consiste typiquement en sulfures, en arséniures, en métaux natifs (or et argent) et en hématite spéculaire, préférentiellement concentrés à l’interface entre les silicates et la gangue de calcite. La séquence de déposition simplifiée des minéraux dans les veines est : (1) «Stade précoce» pyrite ± chalcopyrite encaissés dans une gangue de quartz ± chlorite; (2) "Stade principal" sulfures polymétalliques (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U), arséniures, et métaux natifs dans une gangue de calcite; et (3) "Stade tardif" calcite massive ± galène. L’altération pénétrative de la Diabase de Nipissing est confinée à des halos étroits (<5 cm) présentant des assemblages marquées par la présence de calcite-chlorite-épidote, tandis qu’un faible halo d’altération en hématite spéculaire, calcite et en allanite-épidote est noté dans les roches sédimentaires environnantes. De par leur âge, leur géologie, leur minéralogie leur paragenèse et leur morphologie, les systèmes de veines aurifères de Merico-Ethel ressemblent beaucoup aux gîtes filoniens d’argent-sulfoarséniures des camps miniers historiques de Cobalt et de Gowganda. Ces observations indiquent que ces veines aurifères constituent une variante des systèmes des veines argentifères et qu’elles partagent"

Jan 1, 2009

By James McKelvey, Larry Drolet, Jason Swartz

INTRODUCTION When divers discovered that sections of a tunnel housing the pipeline that conveys wastewater from the Charleston Peninsula to the Plum Island Wastewater Treatment Facility had caved in, the Charleston Commissioners of Public Works(CPW) moved quickly to determine a long term solution for the city’s collection system, immediately focusing on the Ashley River sewer tunnel along the western boundary of the peninsula. Working with the Charleston community, as well as federal, state, and local officials, CPW developed a fast track yet long life design that can be used as a model for underground construction of tunnels in urban areas. The paper that follows summarizes key aspects of the Ashley River sewer tunnel project. HISTORICAL CHARLESTON Charleston, South Carolina is a culturally significant and historic city that was originally settled in 1670. There are over 100 buildings on the National Register of Historic Places within the Charleston area. Additionally, the first shots of the American Civil War were fired at Fort Sumter in the Charleston Harbor in 1861. As one can imagine, tourism generates significant business for the area with over 1.5 million people visiting Charleston each year. No project, especially one that requires digging, is done within the old city on the Charleston peninsula without careful planning. Many precautions are necessary to prevent damage or disruption to the historical properties. The Ashley River sewer tunnel project is exclusively in the old city. A lot of work was done during the design phase to minimize the impact to historical properties. Some of this work included: an archeological study (where pre-digs were monitored at all shaft sites by an archeologist); a building/structure assessment study (where structures near a shaft site were completely surveyed and cataloged); and an environmental study.

Jan 1, 2005

By N. Thorp, S. J. Bluhm

It has long been recognized that the provision of an acceptable thermal environment minimizes the danger and the adverse effect of heat stress, which is directly linked to decreased productivity, increased accident rates, and excessive physiological strain in workmen. Refrigeration in one form or another helps to provide this acceptable thermal environment. This paper outlines the problems encountered in a working area, and the steps taken to alleviate environmental conditions in some stopes with the introduction of selective cooling employing small water-chilling units in conjunction with specially designed stope coolers. Performance figures are given for plant and stope coolers, and the effectiveness of the system is assessed from an evaluation of the improvement achieved in the environmental conditions.

Jan 1, 1986

By W. C. Ellis, E. S. Greiner, M. E. Fine

Discontinuous changes of Young&apos;s modulus, internal friction, coefficient of expansion, electrical resistivity, and thermoelectric power are evidence for a transition in chromium near 37OC. Although the X-ray diffraction pattern gives no clue, a difference between the thermal expansivity and the temperature dependence of the lattice parameter suggests a crystal-lographic change. Young&apos;s modulus data disclosed another transition near THE thermal dependence of a number of proper- ties of chromium indicates a transition occurring over a temperature range near room temperature. Bridgman&apos; noted this first from a minimum in the electrical resistivity near 12°C. In a sample of greater purity, Sochtig&apos; observed the minimum at 41 °C. Erfling3 reported an inflection in the thermal expansivity curve at 36°C. These temperature-dependence curves are reversible with no hysteresis being detected. No discontinuity or inflection has been observed in the heat capacity&apos; or the paramagnetic susceptibility.&apos; Likewise, no one has noted a change in crystal symmetry. In the present investigation Young&apos;s modulus, internal friction, coefficient of expansion, electrical resistivity, illustrated in Fig. 1, lattice constant, Fig. 2, thermal electromotive force, Fig. 3, and paramagnetic susceptibility, Fig. 4, were measured over an extended temperature range. The samples were prepared in two ways: (1) By cold pressing a sintered electrolytic powder compact,&apos; and (2) by electroforming from an aqueous solution. The electroformed samples were prepared by R. A. Ehrhardt and G. Bittrich by plating on copper or nickel tubes from an aqueous solution according to the method of Brenner, Burkhead, and Jennings.&apos; The pressed powder samples (method 1) were finally annealed at 1400°C in purified helium: the electroformed samples, packed in powdered chromium, were vacuum-annealed at 1000°C. From the composition of the original powder&apos; the purity of the pressed powder samples is estimated to be 99.8 pct Cr. Spectrochemical analysis furnished by E. K. Jaycox, revealed only slight traces of impurities in the electroformed sample (less than 0.001 pct), neither iron nor nickel being detected. Chromium deposited by this method is reported to contain approximately 0.05 pct 0.- Methods and Data Young&apos;s Modulus: For measurement of Young&apos;s modulus, an annealed, pressed powder sample, 0.114 x0.237x1.845 in., and an electroformed sample, 0.10 in. od, 0.01 in. id, and 1.86 in. long, were prepared. The resonant frequencies of the rod samples in forced longitudinal vibration were measured at a series of temperatures from —192" to 200°C by a method previously de~cribed.6,7 Because the samples were nonferromagnetic, iron- silicon or molybdenum permalloy tips (0.013 in. thick) were soldered to the ends. The softening temperature of the solder limited the temperature of measurement. Young&apos;s modulus, E,, of chromium at temperature, T, may be calculated from the resonant frequency of the composite rod, f,; the thickness of the tips, t; the length of the chromium sample at 25°C, l,.; the density of chromium at 25°C, pc (7.20 g per cc);5 and the thermal expansivity, Al/l25. Modulus differences for two temperatures, ET and E, are accurate to +0.002x10" dynes per cm2. ET = 4PAlc+2tyf Young&apos;s modulus at 25°C, Fig. la, is 28.2~10" dynes per cm&apos; (40.8xlO" si) in wrought chromium (upper curve). The modulus of the electroformed sample is apparently lower due to cracks. From the modulus measurements two transitions were observed: one with a critical temperature at 37°C, the other at —152°C. Internal Friction: The internal friction, 1/Q, was determined from the width, Af, of the strain amplitude-frequency curve at 0.707 times the strain amplitude at resonance;&apos; the internal friction, 1/Q, then equals Af/f. Fig. lb shows a sharp peak in internal friction at 38°C. The internal friction of the electroformed sample had a similar maximum. Thermal Expansion: The expansivity measurements, shown in Fig. 2, covering the temperature range —195" to +400°C were made by D. MacNair in an interferometric dilatometer8 sing a sample consisting of three pyramids 0.25 in. high prepared from wrought electrolytic chromium. Below —120°C the experimental points deviated up to ±2x10 from the drawn expansivity curve in Fig. 2 because of decreased precision of the quartz wedge thermometer at low temperatures. Near 38°C the thermal expansivity curve, Fig. 2, goes through an inflection corresponding to a minimum in the coefficient of expansion, Fig. ld, and a relative volume decrease on heating. Electrical Resistivity: The variation of electrical resistivity with temperature measured by the po-tentiometric method is also shown in Fig. l. The resistivity of the wrought chromium (upper curve) at 20°C is 13.6 microhm-cm; of electroformed chromium (lower curve) 12.8 microhm-cm. The lower value reflects higher purity and agrees closely with a published value." A minimum at 40°C occurs in the resistivity curves of both samples. No conclusive evidence for a transition near — 150°C was observed, but the points, Fig. 1, appear to deviate from a smooth curve between —120" and —160°C.

Jan 1, 1952

By Brian T. Brady

The year 1992 recorded unimpressive economic growth and uncertainties over what changes would occur for the financial market. Falling interest rates in the United States and elsewhere tended to exert a number of positive influences on financial markets and, indirectly, the mining and quarrying industry. The interest rate declines during 1992 were no exception. Lower rates prompted many investors to turn their attention to long-term investments such as stocks that offer potentially greater rates of return, causing large cash inflows into the equity market. Lower rates made it easier for businesses to finance growth and for consumers to finance the purchase of products businesses made. Also the rates enabled many companies to increase their health and profitability by refinancing their existing loans at lower rates. Falling interest rates were not confined to the United States. With Japan and Western Europe in the midst of economic slumps, marketing authorities in many countries overseas lowered rates in an effort to stimulate business activity. True to form, that contributed to stock market rallies abroad. Stabilizing inflation and lower interests stimulated the industry during 1992 and will likely influence favorably the industry for the next few years.

Jan 1, 1992

Whilst the fossil fuel-based power industry moves towards carbon capture and storage (CCS) or so-called &apos;geosequestration&apos;, the minerals industry should adapt to reap the benefits of the new technology. If CCS becomes viable, the door is open to potential key developments in mineral processing. For example, truly continuous steelmaking could at last be realised using natural or manufactured gas combined with generic melt circulation. Iron ore fines would form a thin molten layer moving countercurrent to the gaseous reductant on one side of a melt circulation loop with efficient post-combustion without deleterious effects of slag accumulation on the other. This eliminates oxygen steelmaking because carbon has no access to the circulating molten iron. Steelmaking merely requires addition of the appropriate low level of carbon and in-line impurities removal to meet product specification. Concerning non-ferrous smelting, nothing short of virtually zero gas emission will be acceptable in the future. For dolomite-hosted Zn/Pb sulfide ores, typified by those in the Carpentaria region of Northern Australia, the way forward proposed is sulfur fixation at the mine site employing the highly exothermic reaction of SO2 with dolomite, followed by encapsulation of sulfated dolomite in fused ore slag. This releases enough energy for direct ore smelting to individual metal products. However, without CCS the strategy would be unacceptable because of greenhouse gas emissions. The scheme is advocated for direct ore smelting at McArthur River. As a result, the environmental problems of disposal of flotation tailings are avoided. Also, highly energy intensive ultra-fine grinding is eliminated, as indeed froth flotation itself, with overall very significant energy savings and exceptionally high increases in metals recovery. Zinc and lead recoveries approaching 99&nbsp;per cent are predicted to be entirely feasible.

Sep 13, 2010

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By W. K. Pincock

Accident prevention can be portrayed as a science that deals with facts and natural phenomena and must be dealt with in the same manner as any other operating problem. Safety at the Copper Queen Branch dates back to 1913 when a Safety Organization was started and rules formulated for underground mining. Since then the mining industry has made substantial progress in the elimination of accidents and when the Lavender Pit was started in 1951, it adopted the general plan in use at all Phelps Dodge properties. Following is a brief description of the Pit Operations:

Jan 1, 1959

By C. D. Thompson, D. C. Violetta, C. A. Czako

The mechanics of the continuous sintering process are briefly reviewed and the application of this process for the beneficiation of principal minerals used in making cement is shown. Pilot plant tests using pyrobeneficiation techniques were conducted with mixtures of limestone and shale in various ratios. Results are illustrated and show the percentage removal of carbon, carbonates, sulfur, alkalies, and volatiles as a function of the limestone-shale ratio. Tests with varying quantities of solid fwls, added to mixtures containing limestone and shale in a 4 to 1 ratio, were made to attain optimum elimination of the volatile constituents. Experimental results show that 90 pct of these constituents were removed during the calcination sintem&apos;ng process. The advantages of using the beneficiated material for making cement are discussed with regard to prepam&apos;ng, handling, and clinkering operations. A sintering process for treating raw materials or kiln waste products which contain high amounts of alkaline materials is described. Tests were performed with a high alkaline waste dust mixed in a 1 to 1 ratio with raw cement meal. The data from these tests and others using different halides for aiding alkali removal are evaluated by the alkali content of the cement clinker. Test results showed that the Dwight-Lloyd process could be applied with facility in beneficiating raw materials for cement making. Substantial quantities of deleterious volutile constituents were removed by calcining and sintering techniques. The continuous sintering process has been applied for a number of years as a means of beneficiating minerals for subsequent conversion to merchantable products. The process was developed and first used for nonferrous metallurgical applicatfons. However, it has risen to prominence for ferrous metallurgical applications where last year in the U.S. and Canada nearly 40 million tons of iron ore were treated by grate firing processes. Through the years of process development many investigators have realized the versatility of the sintering process and have directed experiments toward the use of it for applications with nonmetallic minerals. These have included calcining limestone, carbonizing coal, expanding shale, and burning cement raw meal. Today commercial sintering plants produce cement clinker from mixtures of limestone and shale, lightweight aggregate from shale or clay, and calcined products from phosphate shale. The mechanics of the downdraft sintering process have been presented by many authors. In general practice the materials to be agglomated are mixed as moistened fines with a solid fuel and this mixture is spread uniformly on the grates of the sintering machine. The charge is then momentarily directed under an ignition furnace. After ignition a continuous downdraft of air promotes combustion of the fuel and through heat transfer particles become partially fused into a coherent mass. This is cooled from continued draft induced after combustion. Many investigators have shown that distinct zones are formed during the process of sintering iron ores. At the midway point of the sintering process these are prominent and are, respectively, from the top of the bed to the bottom, comprised of a cooling zone of sintered material, a combustion zone of sinter formation, a calcination zone, a drying zone, and a zone of unreacted materials. Completion of sintering occurs near the discharge end of the machine where the firing zone approaches either the grates or grate dressing material called hearth layer. Here the peak draft temperature usually can be noted in the windboxes. The zonal pattern has been illustrated with the use of graphs which show thermal gradients as they progress through the bed of materials during sintering. Fig. 1 shows, in simplified form, thermal gradients existing when clinkering cement on a sintering machine. The thermal gradients illustrated are for periods of initiation, midway and completion of the clinkering process. The occurrence of these zones has importance for the beneficiation of cement raw materials. A research program was performed at the Dwight-

Jan 1, 1961

By M. C. Ruiz, M. E. Godoy, J. B. Rivarola, M. W. Ojeda

The amount of Pd recovered from an exhausted olefin hydrogenation catalyst was found to depend on mixing technique, particle size, carbon percentage, chlorine flow, reaction time and temperature. Pd extraction was total when a sample in the 125-175 micrometre particle size range was chlorinated for 60 min at 723 K with 20 cm3 Cl2/min, for 60 min at 748 K with 30 cm3 Cl2/min and for 30 min at 773 K with 30 cm3 Cl2/min. No C addition was needed; the initial C content of the catalyst was sufficient for total recovery. Pd extraction was also affected by heat treatment in different atmospheres before chlorination. Treatment with O2, N2 and N2 with traces of O2 led to different degrees of oxidation of C and permitted the formation of oxidised Pd species. Thermal pretreatment in N2 with traces of O2 was most conducive to Pd extraction

Jun 21, 1905