Search Documents

By E. R. Maize

[In report of Investigations 3452,5/ baling with roof movement in the Crucible mine, reference was made do to the fact tart timber decay was being studied at the time of writing. This roper, written after completion of that study, describes s the work and summarizes the data obtained. When the study of roof movement as begun at Crucible two ideas were advanced on decay Of timber by some of the officials: (1) That timber decay vas unusually rapid in the Crucible mine, and (2) that timber coated with rock dust decayed more rapidly than those teat were not so coated. There yore no records by which these ideas could be tested, and it appeared wise to make a limited; investigation particularly of the effect of rock dusting on decay, as rock dusting is an important means of preventing coal-dust explosions.]

Jan 1, 1940

By R. D. Hagni

Pyrometallurgical products from lime roasting of refractory gold ores, pyrite, and arsenopyrite have been examined for their mineralogy, porosity, permeability, retention of contaminant sulfur and arsenic, and potential effectiveness of gold extraction. Cathodoluminescence microscopy, supplemented by X-ray diffraction and scanning electron microscopy-energy dispersive analysis study, has shown that the products phases have characteristic cathodoluminescence properties as follows: anhydrite (CaS04), deep blue; unreacted portlandite (Ca(OH)2), deep purple; oldhamite (CaS), light yellow to rarely pink or orange; a sulfur-rich, arsenic-poor phase, violet; an arsenic-rich, sulfur-poor phase, non-CL. Within the temperature range examined (400-850°C), hematite exhibits greater porosity and permeability at the intermediate roast temperatures of 600-650°C.

Jan 1, 1993

By Christopher Newman, Andrew Minckley

With underground stone operations developing in deeper and more geologically complex conditions, accurate pillar stability analysis becomes for the evaluation of engineering design. This paper provides engineering-based recommendations for applying LaModel to evaluate multiple-level room-and-pillar stone mines in both shallow and deep cover. It provides practical guidance on model calibration using field observations, selection of input parameters, and interpretation of results to inform design and operational decisions. The analysis demonstrates LaModel’s effectiveness in simulating pillar load transfer, stress redistribution, and failure mechanisms in complex mining geometries where empirical methods may be inadequate.

Feb 22, 2026

The corrosion of aluminosilicate refractories by soda from three different sources has been studied by microscopic methods. Sodium sulphate from oil ash, sodium chloride used in glazing structural clay products, and sodium borate from borax-impregnated wood ash have fundamentally the same effect on the refractories. The soda is the chief medium of reaction and fluxing, the sulphur, chlorine, and boron being volatized as sulphuric, hydrochloric, and boric acids.INTRODUCTIONBecause of their strong fluxing action, alkalis are one of the main causes of corrosion and slagging of refractories.The action of potash and soda on refractories follows somewhat similar lines, although it is common for one alkali to be greatly in excess of the other. The course of the reaction in a number of cases of alkali attack has been studied by microscopic and chemical methods. For example, the action of potash on blast furnace refractories was studied by Kraner (1942) and Rigby and Richardson (1947), who described the occurrence of various potassium aluminium silicates. Its action on cement kiln refractories was described by Brisbane, Segnit, and Weymouth (1957). The action of soda on glass tank refractories has been studied by many people, for example Bisby (1956) and Resch (1954). Clews, Hugill, and Green (1940) made a microscopic examination of the attack by soda on silica bricks from a gas retort.Some recent cases of corrosion of aluminosilicate refractories which were brought to the attention of the Division of Building Research, C.S.I.R.O., illustrate phenomena which occur under conditions different from those...

Jan 1, 1964

By J. K. Weglo, M. U. Savich

"The measurement and evaluation of the noise emanating from an ST4A scooptram in an underground stope under a simulated work cycle, and under three conditions of after-treatment systems is covered.These include scooptram without muffler or filler (bare engine), an in-line small filter, compared to a larger-filter, and the larger filter with an in-line muffler in series with fume diluter, which were tested under three engine operating conditions-IDLE, wide open throttle (W. 0. T.), and working condition. This is load, short haul and dump operation.The results showed an attenuation of the scooptram at work of 8 to 15 dBA, 16 cm from the exhaust pipe of the machine, to 4.8 dBA at the operator's ear. Recommendations are made to increase the attenuation at the operator 's ear by additional improvement in design of the fume diluter.IntroductionIn current mining operations, the diesel engine provides a safe, efficient and highly mobile source of power. In the major underground mine s in Canada the most common types of diesel equipment are load-haul-dump (LHD) machines and ore trucks. In general, there is a tendency to use high horsepower, diesel LHD machines in mines to achieve maximum productivity. The increased use of diesel-powered equipment in underground mines has shown no cause pressure levels were measured at the exhaust and outlet pipe. Also, while measuring the octave band and A-weighted sound pressure levels, the operator's position was also measured."

Jan 1, 1986

By M. J. Collins

Direct pressure leaching of zinc sulphide concentrates was started? commercially in October 1980. Continuing research and development studies at Sherritt and feasibility studies for a number of clients have defined various pressure leach configurations for integrattons with existing roast- 1 each operations and for grass roots plants. Existing and potential applications of zinc pressure leaching are discussed.

Jan 1, 1990

By B. F. Naylor

"INTRODUCTION Investigation of the physical properties of electrolytic manganese and its alloys has constituted a part of the program of the Bureau of Mines for several years, and already extensive data have been reported. 3-14/ Heat-content measurements above 25° C. of pure manganese 15/ were completed recently at the Pacific Experiment Station of the Bureau, and the results obtained removed many of the inconsistencies in previously reported data. This paper reports heat-content data of seven manganese-copper alloys, varying in composition from 25 to 90 percent man-ganese. The alloys, obtained from the Salt Lake City Station, 16/ had been quenched from 850° C, and cold-worked. Without further heat treatment, heat-content measurements of each of these alloys were made at 100° or less temperature intervals from 450° to 850º C., as it was considered likely that any abnormal behavior of the specific heat would be found in this temperature range. Also, a portion of each alloy was heat-aged at given temperatures for periods of time thought sufficient to reach phase-equilibrium; then the heat-contents above 25° C. were determined at the aging temperatures. (Heat-aging was done at approximately 450°, 550°, 650°, 750°, and 850° C.)METHOD AND MATERIALSThe heat contents were determined by the ""drop"" method in a previously described apparatus. 17/ The calorimeter was cali-brated with electrical energy, measured in international joules, and the results were converted to the conventional thermochemical calorie by the relation, 1 cal. = 4.1833 int. joules."

Jan 1, 1946

By D. W. Boydell, E. B. Viljoen

A flowsheet incorporating rotary-drum filtration for the solid-liquid separation step, followed by solvent extraction for uranium purification, is used as a standard against which four flowsheets are compared. These flowsheets employ either counter current decantation or belt filtration for solid-liquid separation, and either solvent extraction or continuous ion exchange plus solvent extraction for the purification step. Sales revenue, taxation, capital expenditure, and operating costs are estimated. These factors are taken into account in the calculation of an incremental net present value for each circuit by the discounting of cash flows at 25 per cent per year over a projected life of 15 years. For the material used in these examples, the highest net present value results from the circuit that employs belt filtration followed by continuous ion exchange and solvent extraction.

Jan 1, 1978

To create a successful growth oriented diamond company that succeeds in the practical business of mining and selling rough diamonds, and which pursues an aggressive exploration strategy to seek and develop worldclass diamond mining opportunities in a market that has become increasingly under-supplied.

May 1, 2008

By P. D. Rao, H. B. Charmbury, D. R. Mitchell

As a result of a changing market pattern for anthracite, there is now an increasing demand for steam size and a decreasing demand for domestic sizes. To help the producer meet this new demand, the authors present the technical aspects of the problem of crushing domestic sizes to steam fineness and size. The market pattern for anthracite coal has changed considerably in recent years. The demand for domestic sizes has been gradually decreasing and the demand for the steam sizes has been increasing. The companies however aim for a maximum production of domestic sizes, since these sizes command premium prices. To meet the market demands, particularly in certain periods of the year, further size reduction of the coarse clean coal is necessary. The present practice of multistage crushing in toothed rolls leads to complicated flow arrangements and is high in cost. Data presented herein indicate that crushers with high reduction ratios could be used with a resulting simplification of crushing flows and an appreciable reduction of capital and operating costs. The different types of crushing equipment investigated included the rotary-type breaker, the jaw crusher, the impactor-type crusher, and the Aerofall mill. CURRENT PRACTICE The standard sizes of anthracite are presented in Table I and market specifications require that any given size be maintained with only a limited amount of oversize and undersize material. The 1958 prices of the various sizes also are presented, so it may be seen that size reduction is only performed when dictated by market demands. At the present time the general practice of crushing anthracite consists of removing the top size and crushing it in a toothed double roll crusher to the next largest size. Consequently, to reduce the domestic egg, stove, and nut sizes to steam sizes of pea, buck, rice, and barley, the original material must be screened to produce the three top sizes and each size must be crushed in three separate rolls to the next largest size. Each crushed product must then be rescreened to remove the oversize for re crush ing. Thus a typical operation would consist of scalping the egg size from a mixture, crushing it to stove size, and rescreening the product. This same cycle would be repeated for the stove and nut sizes requiring three screens and three crushers as well as conveying equipment to handle the crushed products. This results in an expensive series of operations to make a product which sells for a lower price. If the three top sizes are crushed in one operation to the smaller sizes then the yield of steam sizes is low and the production of Nos. 4 and 5 sizes is large. These sizes sell for lower prices than the steam sizes. A typical operation is presented in Fig. 1. From the figure it may be seen that the original cleaned anthracite contains 67.4 pet domestic sizes, 26.4 pct steam sizes, and 6.2 pct fines. After multistage crushing of the domestic to steam sizes the composition of the product is 0.6 pct domestic sizes, 89.6 pct steam sizes, and 9.8 pct fines. From a technical standpoint these results are reasonable but the handling and crushing costs are

Jan 1, 1961

By L. B. Herring, Harold Decker

The area under discussion includes districts 2 and 4, so designated by the Texas Railroad Commission,‡ and comprises the following 26 counties: Bee, Brooks, Calhoun, Cameron, De Witt, Duval, Goliad, Gonzales, Hidalgo, Jackson, Jim Hogg, Jim Wells, Karnes, Kenedy, Kleburg, Lavaca, Live Oak, Nueces, Refu-gio, San Patricia, Starr, Victoria, Webb, Willacy, Wilson and Zapata. Drilling and Production The total number of wells drilled in this district during 1944 is shown in Table 5. This indicates a 41 per cent increase in all drilling over 1943. In spite of every handicap created by the war, the oil industry more than met the crisis in its drilling program in this district. Last year we thought it would be impossible to add to the total number of wells drilled in the previous yea;, but in spite of the lack of manpower and materials this large increase was shown. During 1944 this district produced 124,201,978 bbl. of oil from 11,607 producing wells, whereas in 1943 it produced 88,421,693 bbl. from 11,211 producing wells. This is an increase of 35,780,285 bbl. of oil. Some decline has been shown in the older fields arid undoubtedly the majority of wells in the district are producing at too high a rate. However, this district has been able to meet any demands made on it by the Petroleum Administration for War for increased production. Discoveries and Extensions There was a slight decline over the preceding year in the number of wildcats drilled, but the number of discoveries increased. In most instances subsequent development has not been sufficient to arrive at preliminary valuations but it appears that the over-all oil discoveries were below normal and that the gas discovcrics were relatively more important. The Canolis and Tijerina pools, Jim Wells County, and the Dan Sullivan pool, Brooks County, appear to be the outstanding oil discoveries of the year. No important oil reserve was discovered or developed in the Wilcox horizons, although considerable wildcatting was done. Important extensions were made at Agua Dulce and Stratton in Nueces and Teleberg Counties. Production was increased appreciably at Willimar, Willacy County, and Seeligson, Jim Wells County, in sands and areas which were apparently productive at the beginning of the year. Refining Most of the major work in the changing and completing of refineries was finished this past year. Some of the most modern refineries in the industry are now located in the Corpus Christi area. Gas and Condensate No new recycling projects were commenced during the year, nor were there any important additions to the old operations. No major gas reserve was developed, although several new discoveries suggest potentid possibilities.

Jan 1, 1945

By F. H. Callaway, W. O. Keller

The various theories as to the well spacing-recovery relationship are reviewed in considerable detail and these theories analyzed in terms of their consistency with modern reservoir engineering concepts. It is concluded that the well spacing problem must be analyzed in terms of recovery efficiency and that a positive answer to the relation between well density and recovery efficiency is not available from direct comparisons of the production histories of wells and fields. The results of an engineering analysis designed to permit approximate calculation of recovery efficiencies as a function of well spacing in a depletion type reservoir from basic reservoir data is presented. Results of this type analysis indicate that the effect of well spacing on recovery efficiency in depletion type reservoirs can be expected to be very small. Limitations of this approach are pointed out, particularly with respect to its application in lenticular reservoirs. Testing techniques are outlined which should indicate whether or not a reservoir is continuous between wells and whether or not satisfactory drainage is being obtained with present spacings. A mass of data of this type indicates continuity to exist in most fields. INTRODUCTION The purpose of this paper is to review critically the engineering aspects of the well spacing problem, both from the standpoint of certain concepts and from the standpoint of reservoir mechanics. The well spacing problem is primarily an economic problem in which the optimum well density for a particular field is that density which will yield the greatest oil recovery consistent with justifiable development costs. The well spacing answer in terms of economic conditions, however, is extremely sensitive to the variation in recovery efficiency with well density. The variation in recovery efficiency with 'References given at end of paper. Manuscript received at the office of the Petroleum Branch October 2, 1949. Paper presented at the Petroleum Branch Meeting in San Antonio. Texas, October 5-7. 1949. well density is properly an engineering problem. Different opinions as to the correct answer to this engineering problem is the basis for most of the wide difference in opinion among various members of the industry as to optimum well spacing. This paper will be confined to the engineering problem of the relation between well density and ultimate oil recovery; economic considerations necessary for the evaluation of optimum well density for any particular field will not be discussed. The paper can be logically divided into two parts. The first part deals with a critical examination of the background and logic of the Cutler Rule and of similar studies by other authors and of related well spacing concepts. It is indicated that the variations in recoveries with well density* observed by Cutler and. others can be logically attributed to regional migration. Theoretical justification of the Cutler type relation wherein observed variations in recovery with well density in the same field is attributed to variations in recovery effiiency, in terms of energy relations, is refuted. The second part consists of a review of concepts of reservoir mechanics with regard to the well density-recovery relation. It is indicated that little variation of recovery efficiency with well density can be expected in a depletion type reservoir, unless lenticular conditions prevent communication between wells. The significance of field test data with regard to the existence or non-existence of lenticular conditions is pointed out. THE CUTLER RULE The first published article concerning the engineering aspects of the well spacing problem to receive wide attention was the work of W. W. Cutler' of the U. S. Bureau of Mines, published in 1924. In a study of decline curves from a large *The expression "well density" as utilized herein refers to the number of acres attributed to each well in a uniform well pattern, and is expressed in acres per well. The term "well spacing" Is utilized to denote the average distance between adjacent wells in a uniform well pattern. †Although the Cutler rule is treated critically in this discussion the authors intend no personal criticism of W. W. Cutler or of his hark The currently accepted concepts of reservoir mechanics were no": existent at the time of Cutler's work, as were even the moat basic tools (such as the bottom hole pressure bomb) for observing reservoir behavior.

Jan 1, 1950

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

By D. Mraz

"In certain instances, rocks around underground excavations behave as a plastic mass. This paper offers several solutions to predicting the mode of plastic flow around cavities and designing mining pillars where plastic conditions exist.IntroductionWhen stresses around underground cavities exceed yield limits of the host rock, the material often behaves as a plastic mass. The best example of this phenomenon is the behaviour of salt rocks in deep salt and potash deposits (more than 500 m deep).However, many other soft rocks exhibit similar properties. For example, Jeremic(1) described certain types of coal yielding plastically under high pressure. Alder suggested that granulated rock behaves plastically.The object of this paper is to propose a de sign procedure for mining pillars exhibiting plastic flow due to the combination of rock properties and in-situ stresses.Prandtl(3) mathematically defined a concept of a generalized, perfectly plastic substance, not possessing the property of strain hardening (Fig. I). He had in mind, a solid with a quasi quasi-isotropic , polycrystalline structure having a well defined yield point, and he postulated that its material elements start and continue to deform plastically when the maximum shearing stress ""'MAX"" reaches a sharp limit, dependent on the mean value of the sum of the major and minor principal stresses:"

Jan 1, 1984

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By Alfredo Valdivia, Jesus Schabib, Vojtech Gall, William Cao, Curt Cicileo, Andrew J. Thompson

"The East Side Access Project (ESA) involves the construction of geometrically complex underground structures including a large number of caverns and bifurcations. Initially conceived as dual lined structures with either traditional concrete or shotcrete final linings (SFL), construction economy, advances in concrete placement technology and scheduling among others led to a wide use of what is referred to as freeform or pneumatically applied concrete (PAC) for the construction of tunnel final linings. PAC is a method of applying concrete without using formwork, where a wet mix concrete is pneumatically installed to encase reinforcement to full lining thickness. PAC has been widely adopted at ESA well beyond initial expectations. The paper addresses the design and construction aspects of the PAC method and contrasts it to traditional SFL lining placement. The experience made provides guidance for future PAC and SFL applications. THE EAST SIDE ACCESS PROJECT AND USE OF FREEFORM CONCRETE The Long Island Rail Road (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodates New Jersey Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the New York City Transit (NYCT) Subway System and Metro North Rail Road. The construction includes mining and lining of new tunnels and facilities under Manhattan and Queens. The tunnels run from Queen’s Sunny Side Yard through the existing 63rd St. Tunnel, underneath Manhattan’s Park Avenue until termination at 37th Street. Differing types of tunneling methods and final lining systems are being used depending on the ground conditions, geometry and size of the excavation, site constraints and functional requirements. Mining of the Queens segment of the ESA Project involved soft ground tunneling by pressurized face tunnel boring machines, cut and cover construction, and conventional tunneling. The Manhattan segment of the ESA Project involves mining in hard rock by tunnel boring machines, drill and blast, and road header."

Jan 1, 2016

By Walter Miller

With returning prosperous conditions in all industries, oil-refinery engineering has found opportunity for the more extensive application of improvements developed during the several years of depression. The year has brought out little of an entirely new nature, but much in wider application of previous worth-while developments. The greatest volume of work done has been in modernizing the distillation and cracking units of existing refineries, particularly by substitution of combination skimming and cracking units for older equipment, and the installation of cracking plants in smaller refineries where formerly only skimming was practiced. A number of entirely new refineries were installed during the year, two of the most important being the 20,000-bbl. refinery by the Atlantic Refining Co., at Atreco, Tex., and a 12,000-bbl. plant by the Wilshire Oil Co., at Norwalk, Calif., these two embodying some of the latest developments in cracking and treating. Total refining capacity for the United States is now reported as being something over 4,000,000 bbl. per day, but a movement is on foot looking to a complete revision of these figures, as experience has indicated not only some overstatement of capacity of equipment but that considerable equipment is included which because of obsolescence and location will probably never be run again. The 3,000,000-bbl. figure which the industry reached during the year's high consuming period required the operation of probably 95 per cent of the country's efficiently usable capacity. Cracking and Polymerization There were no new outstanding developments in the cracking field, progress being made largely in the further refinement of known principles. Improvements in furnace design and operation have been largely in permitting closer control of the heating curve through the cracking-tube system, assisting in more uniform yield and in the lessening of coke deposition, and permitting longer trouble-free operating time as well as reduction in furnace-maintenance cost. Actual operating polymerization capacity has been increased little during the year, but a number of projects have been started, some nearing completion, the production from which will be available during 1937.

Jan 1, 1937

By Lin Li

A reliability based analysis method for a drilled shaft stabilized slope system is presented in this paper. In the past effort, a deterministic method using the limiting equilibrium method of slices for determining the global factor of safety of a slope reinforced by a row of drilled shafts was developed using the soil arching concept. The drilled shaft stabilization mechanisms for the slope were treated as the drilled shaft induced soil arching, which reduces the driving forces on the down slope side of the drilled shaft. The effect of drilled shafts induced soil arching on the reduction of the driving stresses in the limiting equilibrium slope stability analysis was quantified by the load transfer factor through extensive finite element simulation studies. A semi-empirical equation was also developed for expressing the load transfer factor as a function of the soil properties, including strength parameters and unit weight as well as the slope geometry and soil profile, the location and spacing of the drilled shaft, and the dimension of the drilled shaft. However, due to the inherent uncertainties of the soil properties and the model error of the semi-empirical load transfer equation, a modification of the deterministic method into a probabilistic method is developed in this paper. The Monte Carlo statistical method is used to generate random variables for the soil strength parameters based on the prescribed probability characteristics, including mean, COV, and the probability distribution function. In addition, the modeling error of the load transfer factor is also treated as a random variable in the Monte Carlo simulation method, in which the mean, COV, and probability distribution function for the bias of the semi-empirical equation are used. The developed theories were coded into a computer program for analyzing complex slope geometry and slope profile conditions. Two examples are shown in the paper to illustrate the analysis results of the developed probability approach for determining the reliability of a drilled shaft stabilized slope system.

By D. Hatfield

"Flotation plants typically aim to maximise recovery at or above a target grade. As the ore from the mine varies, operators increase or decrease the mass pull in different flotation banks by adjusting air and level set points in order to achieve target concentrate grade. A methodology has been developed to maximise overall recovery at target grade by determining the optimal mass pull for each bank. However, the approach of targeting equal grade for each ore type in the deposit leads to sub-optimal overall recovery. This is because some ore types sacrifice a large amount of recovery to reach target grade while others easily achieve target grade and can be processed at higher than target grade for little or no loss in recovery. Processing different ore types at different grades and blending the concentrates therefore gives a higher overall recovery.This paper presents a case study where an 80 year production forecast was made for a large Chilean copper concentrator in feasibility stage. A circuit model was created using SGS’s Integrated Geometallurgical Simulator (IGS) for the different ore types to be processed. The model was calibrated from standard rougher flotation tests (MFT), cleaner tests and from the results of plant surveys of similar operations. The pull rates for each bank in the circuit were determined to achieve an optimal graderecovery curve for each ore type. These curves were combined at different concentrate grades for each ore type to obtain the mathematically optimal overall recovery at target grade. The paper shows a methodology for obtaining an optimal combination of operating conditions for each ore type to maximise overall recovery at a set combined concentrate grade."

Jan 1, 2013