Search Documents

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By Honggang Zhong, Wei Du, Qijie Zhai, Junjie Sun, Jingzheng Ye

"Effects of pouring temperature and cooling water flux on solidification structure of ferritic stainless steel are investigated with a thermal simulation setup. The results show that with pouring temperatures 1518° C, 1528° C, 1538° C and 1548° C, both Lmean (the mean length between columnar to equiaxed transition(CET) position and chill surface of the samples) and the mean dimension of equiaxed grains increase. On the other hand, with cooling water flux 400, 800, 1200 and 1600mL/min, Lmean gradually increases, and the mean dimension of equiaxed grains decreases. In addition, low pouring temperature and cooling water flux enlarge the ratio of fine equiaxed grains.IntroductionFerritic stainless steel plays an important role in industry products nowadays. Compared with austenitic stainless steel which contains both chromium and nickel, ferritic stainless steel can obtain good corrosion resistance despite the absence of nickel [ 1]. F erritic stainless steel has been widely applied in automotive exhaust systems [2], electrical equipment, construction and chemical industries and also has broad development prospects. At present, continuous casting technique has developed into an important technology applied in iron and steel making. The solidification structure of continuous casting slab has significant influence on the final properties of stainless steel. The developed columnar grains of ferritic stainless steel would result in negative effects on mechanical property [3]. However, fine and homogeneou& equiaxed grains can improve the comprehensive properties of ferritic stainless steel [4] Therefore, it makes great sense to promote the columnar to equiaxed grain transition (CET). Recently Baosteel has developed a new type of Cr-saved ferritic stainless steel, but the effect of continuous casting conditions on its solidification structure is unknown. It is important to investigate the effects of solidification conditions on solidification structure of this new ferritic stainless steel, which can give guidance for optimizing the production process."

Jan 1, 2014

By Lyon R. J P

The quartz-cassiterite-wolfram veins at the Aberfoyle Tin Mine, north-eastern Tasmania, form a sheeted zone about 200 ft. wide and 1,600 ft. long in slightly contact metamorphosed shales, slates and greywackes, and are associated with a cupola of aplitic granite whose top is about 1,050 ft. below the present surface. Economic mineralization persists from the surface down to a vertical depth of 1,050 ft. to 1,100 ft., dying away in the vicinity of the cupola. Down to the 9-level there is a progressive increase in wolfram content of the veins, and a decline in cassiterite content, with increasing depth.The veins are banded or zoned, with a seivedge of muscovite on the wall. Cassiterite, wolfram and sphalerite occur inside the selvedges, projecting into a core of quartz of varying width. Other sulphides form the central part of some narrow veins, or occur as clots in the quartz. The general sequence of deposition of the ore minerals was: (1) cassiterite, wolfram; (2) arsenopyrite, pyrite, molybdenite; (3) pyrrhotite (in part); (4) blende-group minerals-chalcopyrite, sphalerite, stannite, pyrrhotite (in part)-as solid solutions; (5) galena, tetrahedrite, matildite, native bismuth, scheelite; (6) marcasite and secondary pyrite, magnetite and hematite. The sequence of deposition of the gangue minerals was: (1) fluorine-bearing minerals-muscovite topaz, apatite, triplite, fluorite-more or less contemporaneous with the cassiterite and wolfram;' (2) quartz-contemporaneous with the earlier sulphides; (3) carbonates--contemporaneous with the later sulphides. The stages overlapped somewhat.The composition of the sphalerite and heat treatment experiments with the solid solutions indicate that the blende-group sulphides were deposited at about 6000 C., and cooled rapidly, so that unmixing of the solid solutions was arrested. This accords with the likelihood that the country rock temperature was not above 2000 C. Annealing experiments at between 3500 C. and 6000 C. led to further precipitation from solid solution at the lower temperatures, and to significant segregation by solid diffusion within, a week, indicating that both deposition and cooling of the ore were rapid processes-completed in a matter of days. Since the mineralizing solutions must have lost some heat during...

Jan 1, 1957

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By J. Shen

Direct methanol fuel cells have been the subject of considerable research in the last decade. Performance levels realized in cells, stacks, and systems show that this technology is a promising power source for a wide range of portable applications. A direct methanol fuel cell (DMFC) operates directly on a methanol fuel stream typically supplied as a methanol/water vapour or as an aqueous methanol solution in liquid feed DMFCs. The fuel streams in DMFCs are usually recirculated in order to remove carbon dioxide and to re-use the diluent and any unreacted fuel in the depleted fuel stream exiting the DMFC. The concentration of methanol in the fuel circulation loop is an important operating parameter because it determines the electrical performance and efficiency of the direct methanol fuel cell system. The methanol concentration in the circulating fuel stream is usually measured continuously with a suitable sensor, and fresh methanol is admitted in accordance with the signal from the sensor. There are many factors to consider in developing a methanol sensor suitable for DMFCs. These factors include sensitivity, cost, size, simplicity, reliability, longevity, concentration range, and dynamic response. In particular, reliability and low cost should be addressed. Methanol concentration sensors measure methanol concentration by means of detecting the variations of physical/chemical properties of the solution. In this work, methanol concentration sensors based on electrochemistry, electric-capacitance measurement, infrared sensing, ultrasound sensing, and other techniques are reviewed to discuss their advantages and disadvantages.

Jan 1, 2005

I reached New York at the start of my second South American adventure on Jan. 9, 1916. In the Anaconda office I found that we were not to take the steamer for two weeks which gave me time to study reports on Potrerillos and Corocoro. Reno Sales, whom I had met in Butte only casually, was to go with us to South America. Though he was only a little older than I, he was already an unquestioned leader of our profession, and we became and remained good friends. William Braden was in New York and would return to Santiago with us. Tom Hamilton would also be returning from a vacation. Leighton Stewart, a young engineer who was to work for Braden, was going on the steamer with us, taking along his wife. And of course Dr. Ricketts would go along. He had just become engaged to John Greenway's half sister, Kate Greenway, and in order not to be away from her longer than was necessary, he did not reach New York until a day before we sailed. This made eight of us who would be in the party. We were to go to Corocoro first, as Braden had taken an option on the Chilean company there. Development was already under way. As reports came in by mail we tried to get as good an idea of the property as we could before the actual examination. Mr. Thayer "put us up" at India House, one of the best lunch clubs in New York, and Reno and I ate our lunches there almost every day. Thayer, Braden, and Cornelius Kelley, who was to succeed Mr. Ryan as president of Anaconda, joined us when they could. At the lunches they told us about the under- ground war in Butte a few years earlier. When I wrote my chapter on the Butte wars in Romantic Copper more than 15 years later I could not help being biased a bit by my friends, all of whom were on the Anaconda side. But their opponents in the Clark and Heinze camp were just as biased in their comments on my book.

Jan 1, 1976

By Marcel M. Djivre

The paper will outline the destructive test methods and test procedures including the evaluation criteria currently used at the Materials Testing Laboratory (MTL), Sudbury, Ontario, Canada, a laboratory approved by the Ontario Minister of Labour for the purpose of testing or examining mine shaft ropes or other hoisting appliances. For the evaluation of the mechanical properties of rope samples used in "ultra-deep" single-lift shafts, additional discard criteria used in Ontario, Quebec and South Africa shall be presented. Most of the methods and test procedures currently used at MTL can also be found in the current CSA G4-00 Standard, Steel Wire Rope for General Purpose and for Mine Hoisting and Mine Haulage, published in November 2000. In this latest or sixth edition of CSA Standard G4-00, a new Clause 14 has been added outlining the requirements for in-service destructive testing of steel wire ropes for mine hoisting applications. The CSA G4-00 Standard is also intended for the manufacturing of new ropes, and includes requirements for raw materials and construction features for round strand and flattened strand rope, and locked coil rope in bright and galvanized finish. To-date the Ontario Mining Regulations require only that destructive test of new ropes be performed in accordance with CSA Standard G4-00, but does not require conformity to the Standard, and on the other hand the inservice wire ropes are required to be tested in accordance with CSA G4 and thus require conformity. The author recommends that the Ontario Mining Regulations (and regulations of other mining jurisdictions) be improved in order to ensure quality control in the manufacturing of wire ropes destined for mines in Ontario (and Canada). Also, the author recommends the revision of the CSA G4-00 Standard by the technical committee in order to address manufacturer?s concerns with respect to compliance, and harmonize the Standard with Internationally recognized Standards.

Apr 1, 2005

By J. K. E. Douglas

PRESIDENTIAL ADDRESS Given by Mr J. K. E. DOUGLAS, M.Se. (Eng.) (Rand) SYNOPSIS Lime is the most widely used and the cheapest chemical alkali known to man and virtually every product we use or eat has required lime in some phase of its manufacture. Its use goes back to the earliest days of man and many ancient buildings and writings bear testimony to this. The manufacture of lime involves quarrying, crushing and screening of limestone and the burning of the sized stone in kilns of which there are several types. The earliest kilns were of very crude design and only in comparatively recent times have large capacity, automated and scientifically controlled kilns been developed. The history of the South African lime industry is largely that of the three main lime companies and their story is briefly told. No other material used in industry has a greater diversity of uses or more varied functions and lime has applications in most South African industries. The main applications are in the production of gold and uranium, iron, steel and ferrochrome, carbide, sugar and paper and for water treatment, agriculture and building. The Republic is well endowed with high quality limestone and the conclusion is drawn that many other minerals will have been exhausted before we run out of limestone with which to process them. The expansion of the lime industry has in the past kept pace with the requirements of industry and the future demand is expected to grow in parallel with the growth of these industries. Since the war this growth has been phenomenal and with our expanding populations and abundance of raw materials it should continue in the years ahead. Limiting factors are the shortage of skilled labour and the distance from export markets. Confidence is expressed that the challenges of the future will be met and that the lime industry will continue to make an important contribution to the growth and prosperity of South Africa. INTRODUCTION Lime, gentlemen, is known to all of you. Like myself, most of you have undoubtedly found it to be, on the appropriate occasion, a most pleasant flavouring for gin. But this lime, or rather its juice, was in earlier days more than just a flavouring. In the days of sail it was vital to the health of sailors as a deterrant against the scourge of all sea-going men-scurvy. It thus played a small but important role in the opening-up of trade routes around the world on which was based the original wealth of many of today's more advanced nations. I propose to address you on the subject of lime this evening, not the citrus variety I have just mentioned, but the most widely-used and cheapest alkali known to man, which, largely unsung, plays an even more vital part in modern industry than did its namesake in the development of inter-continental trade. In the time at my disposal, I propose to tell you something of the history, geology and technology of lime manufacture. Then I will briefly sketch for you the development of this industry in South Africa and indicate the role it plays in supplying the requirements of many of our important industries. Finally we will attempt to look into the future. The importance of this chemical alkali to our modern civilization is seldom fully appreciated-virtually every product we use or eat has required lime in some phase of its manufacture, either directly or indirectly. It is one of those basic materials, along with iron, coal, sulphur, salt and petroleum without which industry and, in fact, our modern way of living could not exist. Fortunately, nature has endowed the world with a plentiful supply of the limestone from which lime is derived and most countries have deposits adequate for their requirements. As a result, not only has there been little trade in lime products between countries but in the past the widespread occurrences of limestone have set a pattern of numerous small plants each serving a limited area. These plants were generally crude affairs incapable of producing a quality product. It is not surprising that, in an industry comprised of small producers with limited financial resources and in fierce competition with each other, there was little interchange of information. Technological development was therefore slow and the industry tended to be regarded as a backyard operation. Its popularity was not enhanced by the fact that lime is difficult and unpleasant to handle if proper facilities are not provided. In recent years the lime industry has undergone very radical changes to meet the more exacting requirements of today's more sophisticated consumers. Only since the war have the larger companies emerged with proper management, highly mechanized plants and a scientific approach. HISTORY Lime was one of the first chemical reagents used by man and consequently lime burning is one of the oldest of the chemical industries. The use of limestone dates back to the stone age when primitive man used limestone to build fireplaces, construct shelters and make crude tools and weapons. It is probable that lime was first discovered by him when the stone in these fireplaces disintegrated to a white powder which he could use for decorative purposes. The first recorded use of limestone was when huge blocks of limestone were used to build the pyramids of Egypt in 4,000 to 2,000 RC. It was not long after this that the beauty of marble, which is in fact a limestone, came to be appreciated and it found wide application in sculpturing and for decorative wall construction. Originally lime, mixed with sand, was used mainly as a mortar for building purposes, the earliest record of its use for chemical purposes being in 350 B.C. in a report of the wreck near Marseilles of a ship carrying a cargo of linen and lime 'for its bleaching'1. Cato mentioned the burning of lime kilns in 184 B.C. and the Romans made extensive use of both limestone and lime for highway construction. A treatise on architecture by Vitruvius who had an official position in the rebuilding of Rome under the Emperor Augustus remained for nearly two thousand

By James J. Scott

In the fall of 1976 the author started test work with Friction Rock Stabilizers in uranium mines of the West, principally in the Ambrosia Lake and Churchrock districts of New Mexico. Tests were also conducted in other uranium mines in the Rocky Mountains area. These mines are plagues with problems in ground control due to the weak formations in which mineralization occurs, mudstones, siltstones, weak sand, etc. For this reason, it is extremely difficult to obtain good anchorage for long periods of time with conventional mechanical roof bolts. Resin bolts give good anchorage but are expensive and, because of hole erosion and difficulties in installation due to inadequate equipment for mixing the resin and placing the rebar, they are not widely used. Field testing was also carried out in trona, limestones and hard and soft shale formations. The mechanism of the Friction Rock Stabi1izer support is discussed and pull test data presented for various rock types.

Jan 1, 1977

By W. S. (Steve) Vaughan

The Origins of Joint Ventures in Canada?s Mining Industry ? Among the most important financing structures used in our mineral industry today ? Virtually unheard of in the Canadian industry prior to the 1970s ? Borrowed from the U.S. oil and gas sector where it came into prominence in the late 1930s ? The Securities Acts of 1933 and 1934 in effect killed the sale of (equity) shares for financing oil and gas wells and start up mining companies

May 1, 2013

By Oswald J. Heinrich

THE great improvements which have been made in late years in the different systems and instruments used to perforate the crust of the earth for purposes of testing and exploring for mineral resources or for other reasons, by means of bore-holes of greater or less diameter and to greater or less depths, are manifold. It may therefore be of interest to make an impartial comparison of them, or of such as are most commonly used. Being well aware of the difficulties which are encountered in such a task, a reasonable allowance must be made in such a comparison. It is a rare instance when even two decidedly different systems or instruments have been used in the same locality, penetrating identically the same strata to the same depth. The diameter of a borehole as well as its greater or less depth must also be considered in regard to its cost per foot, etc. But for practical purposes, for ex¬ploration at least, we may assert this rule Any borehole, of whatever diameter, which allows the means of examining the strata most carefully and completely, will be sufficient for this purpose, but that one which will do it most economically and in the least space of time, must be considered the best for it. It will, therefore, partially depend upon circumstances, what system, in spite of other superiorities, may be the best in each case, and the following remarks may aid in deciding this question. To make the attempt here to review all that has been published upon the different systems and means of boring would be out of place. Reference can be had to the able publications treating upon this subject. A difference in this respect exists in regard to the use of the hollow rods in connection with the diamond drill, used for that purpose. The great future, which appears to be evident for this instrument, will be warrant enough for any one, who has had the opportunity to test it, to give his experience to the public. Only in this way can we bring this system to such perfection, as it seems to deserve and * The drawings illustrating this paper are one-half the size of the tools represented, with the exception of the instrument used to reverse the current in the bore-hole (Fig. 17), which is one-third the actual size.

Jan 1, 1874

By R. R. Templeton

THE year 1924 was particularly notable in the petroleum industry of California as it was a period in which extensive town-lot drilling, with attendant overproduction and allied problems, virtually ceased and the industry returned to a nearly normal condition. Nearly all major field operations were conducted by large operating and marketing companies; in contrast to 1922 and 1923 field operations, when small promotion companies set the pace and forced the large companies to follow. The outstanding features of petroleum development were: 1. The three major fields of 1923, namely Huntington Beach, Long Beach, and Santa Fe Springs, declined from a production of 13,042,939 bbl., in January, to 6,764,417 bbl., in December, a drop of nearly 52 per cent: During this period, Huntington Beach declined 35 per cent., Long Beach 42 per cent., and Santa Fe Springs 63 per cent. 2. Methods of pumping deep wells were improved in some particulars; this contributed toward sustaining the productions of these three famous fields above what was predicted. 3. Of the fields producing previous to 1924, only three increased in production to any appreciable degree, during the year, as the result of bringing in new wells. These fields are Dominguez, Torrance, and Wheeler Ridge. Dominguez, discovered in September, 1923, produced 56,851 bbl. in January and increased regularly to a production of 1,641,042 bbl. in December. Torrance increased from a production of 972,261 bbl. in January, to 1,783,670 bbl., in May, and then declined to 1,393,215 bbl. in December. Wheeler Ridge, discovered in January, 1923, produced 23,254 bbl., in January, 1924, increased to a high of 33,678 bbl., in September, and declined to 27,430 bbl. in December. 4. Nearly all the production that had been shut-in during 1923 was opened in 1924, except some wells chiefly in Coalinga, Fullerton, and Santa Maria districts. The opening up of this shut-in production, combined with the increased productions from Dominguez and Torrance, were the chief factors that held the rate of decline for the state to a gentle slope.

Jan 7, 1925

By R. C. Kadyk, C. J. Bise

High-voltage cable couplers are convenient and widely used accessories in modern coal-mine power distribution systems to help extend and retract power-feeder cables throughout a mine. Coupler design has tried to keep pace with the industry's desire to move to higher distribution levels, but the increase in recorded failures of 15-kV class couplers, which serve the 12.47-kV and above distribution levels, has inhibited this transition. Problems associated with the effects of partial discharge on high-voltage cable couplers are analyzed. The phenomenon of partial discharge is discussed, a testing standard is developed, and various coupler designs are subjected to its requirements. An analysis of test results and results based on field applications are provided.

Jan 1, 1985

By T. K. Dichmann, J. A. Finch

"Microflotation, laboratory batch, and in-plant minicell continuous tests were conducted to determine if copper ions not only activate sphalerite but also depress pyrite when the minerals are together. Microflotation tests showed that pyrite recovery increased with addition of copper ions in the pH range of 5-10 when alone, but decreased when sphalerite was also present. Batch flotation tests (Red Dog ore) showed that upon addition of copper, pyrite recovery decreased significantly. The continuous tests (Louvicourt Mine) confirmed this and indicated that with excess copper pyrite recovery can increase. The results suggest there is competition for copper and xanthate in favour of sphalerite. To take advantage of this competition it may be necessary to control the sequence and rate of copper, collector, and lime addition. INTRODUCTIONFlotation, in common with all physical separations, is an imperfect process that results in misplacement of minerals. One source of this imperfection is accidental activation by contaminating metal ions. An important practical example is the misplacement of pyrite to zinc concentrates. Flotation of sphalerite generally requires activation by copper ions, added as copper sulphate. Copper ions are also used to activate pyrite [l] hence there is the suspicion that accidental activation contributes to the recovery of pyrite (Py) with the sphalerite (Sp). However, recent literature has shown that copper ions may make Py less floatable if Sp is also present. Xu et al. [2] conducted continuous minicell tests in-plant at Kidd Creek Operations (division of Falconbridge Ltd.) and showed that while the addition of copper sulphate improved zinc/iron selectivity, it did so as much by reducing the recovery of pyrite as increasing zinc recovery (Figure 1)."

Jan 1, 2000

By Mauricio Coto

Three bidirectional static load tests (BDSLT) were executed on bored concrete piles, as part of the permanent foundations for two buildings sites located at the Sabana, San Jose, Costa Rica, separated at a relatively short distance of about 1 km. Unit skin friction values obtained for both sites, principally for the “Lahar” layer show that in general, friction pile capacity from the tests is higher than anticipated per static calculations from soil borings geotechnical parameters correlations. Results from the tests were also compared with dynamic load tests (DLT) executed at other two sites in the surrounding area, and with a Finite Element (FE) Analysis that model soil-pile interaction for one of the projects. On the other side, some construction issues were detected on one of the sites, which negatively affected the end bearing capacity, but being that pile friction was higher than anticipated, the required overall pile capacity was accomplished. The BDSLTs results of these tests help to better understand the geotechnical behavior of the soil layers in the Sabana. Moreover, they also show that is possible to optimize the design and construction of other bored pile supported buildings and structures on the zone.

The Autogenous Fine Grinding Kelsey Axial Displacement (KAD) Mill The marginal improvements which continue to be made to fine grinding practices have exposed the limits of conventional technologies and highlighted the need for a radically new approach. The patented autogenous Kelsey Axial Displacement (KAD) Mill design consists of a rotating spherical grinding chamber, which shares the same spherical centre as the shaft-mounted counter-rotating disc assembly. The axis of the disc assembly can be inclined to the axis of the spherical grinding chamber by pivoting the disc shaft about the common spherical centre. The inter-particle energy transfer required for breakage results from particle velocity differentials created by the discs intercepting the rotating mass. Particle size reduction is concentrated in high shear zones, which envelop the outer surface and periphery of the discs. This paper traces the development of the KAD Mill from pilot to commercial scale. Pilot work covers a range of minerals including magnetite, calcite, dolomite, barite, limestone and talc. Test results include open and closed circuit operation in wet and dry modes. Conventional milling constraints and energy consumption issues are addressed while new dimensions are added to the feed size range acceptable for wet and dry grinding to fine and ultra-fine sizes.

Sep 13, 2010

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By Hollis Peacock

THE Bingham area in the West Mountain mining district on the eastern slope of the Oquirrh range, some 28 miles southwest of Salt Lake City, has been the most consistent producer for the United States Smelting Refining and Mining Company, production having been continuous, except for minor interruptions, since the organization of the United States Mining Co. in 1899. This production has come from fissures and mantos largely within limestone members aggregating something less than 10 per cent of a thick quartzite sequence of Pennsylvanian age which has been warped into an open syncline plunging northwesterly. Bedding on the easterly limb dips 10°-45° but steep-ens to 90° and even overturns on the westerly limb. Ore bodies cluster about the more northerly of two elongate interconnecting stocks of monzonite which have risen in an axial position within this syncline. Largely within the more northerly of these stocks is the low-grade copper ore body exploited in the Utah Copper open cut of the Kennecott Copper Corp. The values, in seams, minute fracture fillings, and disseminations of pyrite and silica, pervade not only the stock but adjacent sediments, and form a nebulous, sprawling mass which both mineralogically and geographically is the center of the district. The more southerly of the twin stocks appears to be comparatively inert and without obvious relation to mineralization. which

Jan 1, 1948

By G. D. Monk, W. C. Krumbein

The relation between permeability and the size parameters of unconsolidated sand is approached by considering sands as logarithmic frequency distributions having the basic parameters mean size and standard deviation. Sieve separates were mixed in accordance with the normal logarithmic probability law, so that the mean and standard deviation could be varied at will. Experiments were conducted in which one parameter was kept fixed and the other varied; in this manner the dependence of permeability on the individual parameters was evaluated. It was found that permeability can he expressed as the product of a power function of the mean size and an exponential function of the standard deviation. Earlier studies of the effect of size of particles on the permeability of uncon-solidated sand have shown that the permeability varies with the square of some average diameter. This was first pointed out by Hazenl in 1892 and verified by Slichter2 in 1898. Hazen's mean size was defined as the 10 percentile of the cumulative curve (i.e., size that is smaller than 90 pel cent of the distribution and larger than 10 per cent). Slichter's effective size, on the other hand, was found by Wilsey3,4 to agree with the 31 percentile. Fair and Hatch6 found that the geometric mean size of sieve separates yielded the same power function; Hulbert and Feben6 found that the permeability of sieve separates varied as the 1.89 power of the median diameter (i.e., the size associated with the 50 percentile of the cumulative curve). Relatively few studies included the effect of the "sorting" of the sediment on the permeability. It was recognized that the nature of the size distribution, in terms of the spread of the particles about the mean, affects the permeability, but no systematic investigations of this effect are known to the writers. Cloud7 demonstrated that the effect of the grain-size distribution on permeability is definitely measurable. In the present paper the authors investigate this relation analytically, and show that the effects of the size parameters on permeability may be predicted for at least a restricted set of conditions. Properties OF Sediments Recent investigations have shown that essentially all the geologically important characteristics of sediments may be expressed in terms of six measurable quanti-tities possessed by each clastic sedimentary particle. These attributes are: (I) size, (2) shape (sphericity), (3) roundness (angularity) , (4) mineralogical composition (density), (5) surface texture, (6) orientation. Each of these characteristics may be defined in several manners. Size may be expressed in terms of sieve mesh, settling velocity, volume, etc. Sphericity is a shape concept introduced by Wadell;8 it is essentially a measure of the ratio of the surface area of an equivalent sphere to the surface area of the particle. The same

Jan 1, 1943