Search Documents

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By P. J. Lloyd

Society is fully justified in its concern about the environment, but that concern may, at present, be too uncritical It is, for instance, essential to establish that there is a valid environmental impact, and that there is truly a causal link between a human activity and an observed shift in environmental conditions. In establishing these, it inessential to recognize that scientific proof offers consistency, but that it can never provide completeness. Thus, no amount of scientific endeavour can ever prove that mitigation of the effects of human activity will be perfect. Society normally expresses its concern through legislation. The existing legislation in South Africa is reviewed, and it is found that [>legislation regarding water is probably too stringent to be effective, >legislation regarding air and land use is probably too lax, >all the environmental legislation is too fragmented to be efficient, and the Department of Environmental Affairs is hamstrung by inter-departmental rivalry. ] It is accordingly concluded that, if means are to be found for ensuring adequate mitigation of environmental impact in the face of ongoing economic development, it is necessary to establish a Judicial Commission on Environmental Affairs advised by, but given greater powers than, the departments currently active in environmental maters. This Commission should be charged with creating, perhaps over a decade, a body of legislation that would guide development while protecting the environment in its widest sense.

Jan 1, 1994

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By John A. Sievert

Sedimentary deposits contain an appreciable portion of the world's supply of uranium. Predictions of nuclear fuel usage in the United States indicate that these reserves will have to be tapped if the domestic industry is to be the major supplier of fuels for the nuclear reactors. Techniques developed within the petroleum industry are a base on which to build economically attractive fluid mining processes for the recovery of these uranium values. The problems central to the success of such mining processes are the containment, control, and recovery of a narrow band of pregnant leach solution as it progresses from the point of injection to the point of production Given sufficient incentive, suitable solutions to these problems can be found

Jan 1, 1970

If one can embrace the medical analogue, much of the mining industry currently suffers from a massive bacterial infection. When pyrite-bearing or sulfide-bearing rock formations, tailings, or mine wastes are infected by Acidithiobacillus ferro-oxidans, the likelihood of forming acid rock drainage (ARD) is almost guaranteed. The ?pharmacy? of antibiotics available is extensive, ranging from solid alkaline amendments like limestone to liquid ?medicines? such as sodium lauryl sulfate, sodium thiocyanate, waste milk, and bipolar lipids. Unfortunately, the ?geo-medical? teams of geochemists, microbiologists, engineers, and mine managers lack the tools to surgically apply these active ingredients where they are needed most with a minimum of waste. Distribution of fine grained limestone on the surface of an acidic mine waste dump is analogous to applying a bandage soaked in antacid to treat an upset stomach. The implementation of up-to-date best management practices has not healed the patient; an equivalent combination of hypodermic needle, cyber knife, and arthroscopic probe is clearly needed. Using an engineered, flow-able or pumpable foam or pHoam? as the medicinally analogous ?dextrose delivery solution? for solid and/or liquid ?geo-antibiotics?, the authors have combined off-the-shelf technologies that have been previously applied in solving geotechnical problems in the mining industry. A patent for the innovative process is pending. This paper discusses method concepts and the advantages it could provide over conventional BMPs.

Jan 1, 2012

By C. Musingwini

Traditionally, mineral reserves management at most underground mines in Zimbabwe focus on maintaining large mineral reserves so that the time between development and production is as long as possible. Historical data at Shabanie mine, a Zimbabwean sub-level caving underground mining operation, confirms this practice. However, the high cost of underground development means that the luxury of large buffer mineral reserves cannot be justified. Furthermore significant increases in the costs of production, exacerbated by the current unfavourable economic climate, make the wisdom of extending development workings well ahead of use questionable. Poor ground conditions at Shabanie mine, mean that some development ends have to be re-mined two or three times due to partial or complete closure between the time they are mined and the time they are utilized. In order to reduce the inordinately high support costs associated with closure of development ends a new ?just-in-time? (JIT) approach that provides development ends as and when they are needed, has been adopted. Accordingly a model to determine an appropriate ?just-in-time? rate of development has been created. The JIT development model indicated that the mine could reduce development rates from 330 m/month in 2001, to 160 m/month in 2002 and achieve savings of about 50% on annual support costs, but still assure customers of a long-term product supply. The mine accepted the model in November 2001 and began implementing it in 2002. Results of the implementation will be reviewed in 2003.

Jan 1, 2003

By Edward H. Robie

IN many ways, the Annual Meeting of the Institute in February was the most successful yet held. Attendance surpassed even that of the 75th Anniversary Meeting in 1947 with its international flavor. The number of technical sessions and the number and quality of papers presented almost certainly set a new record. The banquet was the best attended of any yet held even though the price reached a new high. Despite the demand for almost 1700 tickets to the banquet, some felt that the price-$13.50-was higher than they could afford. There are two points of view: One is that this is the big social event of the year for members and that it is worth from three to five dollars more to have it at the Waldorf and to have a luxury menu, as we did this year, with turtle soup, a fish course, guinea hen for the entree, and wild rice (which we understand is $3.50 per lb) for a vegetable. The other point of view is that a seven or eight dollar banquet of more simple food at the Commodore Hotel would more than make up in appeal, especially to the younger and less well-heeled members, what it would lack in glamour.

Jan 1, 1952

By Darryel Boucher, Raymond Langlois, Neil Rowson, Kristian Waters

The Knelson Concentrator is a centrifugal gravity concentrator composed of a high speed rotating bowl into which a mineral slurry is fed. The rotational motion creates a centrifugal acceleration up to an equivalent of 200 G. Under this acceleration, particles enter fluidised riffles along the side of the bowl, with the fluidisation allowing for the substitution of dense material for less dense. The separation mechanism is not fully understood and questions remain on the optimal residence time, slurry feed parameters and bowl surface profile to achieve a better separation. The positron emission particle tracking (PEPT) technique has been applied to record the motion of a -1700+1180 µm particle of a quartz-gold matrix, labelled with 18F radioisotope while it undergoes concentration inside a 3" laboratory scale Knelson Concentrator (KC-MD3) operated at 60 G. The slurry used was composed of quartz and magnetite. Particle trajectories during the first stage of the concentration process where the heavier particles centrifuge through the increasingly dense slurry towards the riffles of the bowl are shown with respect to time. This work reveals new information on particle motion inside the Knelson Concentrator and the results will be used for validation of developed separation model as well as optimisation of a centrifugal concentrator’s performance.

Jan 1, 2014

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GrG) test procedure at McGill university is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill university has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GrG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill university. as a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GrG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GrG tests were carried out at McGill universityon ores from all over the world. recently, a modi?ed version of the GrG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GrG in a sample; this simpli?ed test has theadvantage of reduced mass, processing time and cost. to recognize and honour the contributions madeby the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GrG test be named after Laplante.

Jan 1, 2010

This paper describes a steam outburst in a metal mine which occurred in December 1992 in Japan, resulting in two fatalities. The outburst occurred just after blasting in a heading face 600 m below surface (SL-50 m), 1664 m from a mouth of the mine. The scale of the outburst was large and the fragments of the outburst spread up to 34 m from the face, the total volume of the outburst was estimated to be 206 m3. The outburst materials were mostly clay originated from the typical surrounding rock of sulfide ore and basalt. The shape of the larger outburst fragments were slabs with a thickness of 10 to 20 cm. The victims were found in a main ventilation air shaft, 175 m and 380 m from the face, respectively. The mine mainly produces copper, lead and zinc. The face was ventilated by a 560 mm diameter duct with a fan and the strata temperature of the rock was estimated to be in the range of 120 to 140¦C. There is a famous hot spring near the mine. A thorough investigation into the unprecedented accident was made including an on-site inspection and investigation of rock characteristics in laboratories.

Jan 1, 2005

"Chairman: Professor B. W. MacKenzieRapporteur: Professor D. A. PretoriusPapers:Optimum spacing for soil sample traverses by W. A. HodgsonEvaluation of geochemical data by C. J. LenzResearch in oil exploration decision-making by J. W. Harbaugh and A. Prelat A drill hole data bank by M. R. AndertonOre reserve estimation and depletion planning for a beach diamond deposit by M. M. OosterveldIn opening the session, the Chairman indicated that the papers and discussions would revolve about quantitative methods of analysis and optimization of various aspects of exploration planning. The five papers would cover a wide range of topics within a general theme of exploration analysis, and it would be appropriate, therefore, to present the. papers as representing a sequential information-gathering process, namely, (i)geochemical and geophysical types of surveying for the location and identification of anomalous zones, (ii) tren¬ching and drilling of the anomalous zones found, and (iii) further refinement of the data for ore reserve calculations and production planning.The first paper, which was presented by Dr W. A. Hodgson, dealt with the optimum spacing between soil sample traverses conducted during geochemical prospecting. The theme of the paper was that the critical sampling interval should be based on the concept of element continuity, and that this interval could be determined by means of a correlogram. Ensuing discussion concerned the probability of the method, designed for areas where dispersion was high, working in localities where dispersion was either low or virtually non-existent. In the latter eases, specific orientation surveys for varying topographic, climatic and geological conditions would possibly be more useful than the preparation of correlograms. A further suggestion was made that cost versus risk should be taken into consideration when deciding upon the spacing between traverses. A balance could be struck by mathematical optimization. If the exploration budget was fixed, then the variance of risk could be minimized.The second paper was a short contribution by Mr C. J. Lenz. Computer-based plotting and evaluation of geochemical prospecting results were carried out because the low cost of analysis in Rhodesia permitted very large volumes of data to be accumulated in mass-coverage operations. Anomalous areas were demarcated within different environments by selecting probability or population boundary values from frequency distributions. In the short discussion which took place it was debated whether the method should be used only in the early high-risk stages of geochemical exploration and whether the introduction of geological bias could influence the actual results of an exploration program."

Jan 1, 2014

By Scott Ellenbecker

The formation in Newmont Mining?s Phoenix Mine near Battle Mountain, NV contains high levels of abrasive quartzite as well as gold, copper and silver. Newmont started mining operations at Phoenix (formerly Battle Mountain Gold) three years ago and the planners knew they were working with a challenging geological formation. But as it turned out, it was more challenging than anticipated. Mine manager Mark Evatz said, ?Anything that touches Phoenix rock wears fast. The rock fights back here.? To contend with the hard conditions, Newmont uses Atlas Copco?s Pit Viper 271 (PV-271) blasthole drill. Because of the hardness of the rock, drilling at Phoenix requires hammer drilling and the mine uses Atlas Copco TD65 hammers with 171 mm (6.75 in.) bits. The mine?s PV-271?s are outfitted with a single 41 m3/min (1450 cfm), 2.4 MPa (350 psi), oil-flooded air compressor. Phoenix has six Atlas Copco PV-271 drill rigs plus an Atlas Copco DML and a DM45 midrange blasthole rig. The mine?s goal is to keep 3.6 Mt (4 million st) of muck in inventory to stay ahead of the shovels and support needed operational flexibility (ore control related). Drilling efficiency has been a continuous point of improvement since operations began at the mine. The single-pass depth capability of 16.5 m (55 ft) on the PV-271 helped with that. Originally, the plans called for 6-m (20-ft) bench heights, supported by 7-m (23-ft) drill depths, and time spent moving from hole to hole was eating up productivity. Drilling on that plan resulted in drilling an average of 14 m/h (47 ft/hour). When depths were changed to 13-m (44-ft) drill depth, supporting blasting of 12-m (40-ft) benches, they were able to use the single pass capacity of the PV-271. Performance increased to more than 18 m/h (60-ft/hour) an hour. Although the drill depth change largely supported the improvement, other aspects of continuous improvement associated with improved knowledge of the Pit Viper drills helped as well.

Jan 1, 2009

By W. B. Dancy, A. Adams

Laboratory test work on heavy liquid separation of sylvite from halite is reported. Numerous tests were run on sylvite ore sized in the ranges of 4x20 mesh, 10x65 mesh, 8x100 mesh, -8 mesh and -10 mesh with heavy liquids in the range of 2.05 to 2.15 sp gr. From the test results, it was concluded that, with the type of ore under study and a size in the range of -8 mesh, a recovery as high as 90% could be achieved with a product grade of 70% KCl. However, a final product at an acceptable recovery cannot be made with one pass, and the float must either be further processed with heavy liquids or dried and sent to a conventional froth flotation circuit. Potash ores occurring in this country consist essentially of sylvite and halite plus minor amounts of magnesium sulfate salts and montmoril-lonite-type clays. Recovery of potash minerals from evaporite ores in the North American potash fields is accomplished almost exclusively by use of amine flotation. European practice involves froth flotation as well as solution-crystallization processes. Laboratory and pilot plant test work has been reported in Europe and the U. S. on the application of heavy media separation to potash ore beneficiation. Work was probably discontinued because of lack of ore with the required very coarse liberation characteristics (1/8 to 1/2 in. liberation size). Sylvite, with a gravity of 1.99, and halite, with a gravity of 2.17, appear to be ideal for separation by heavy liquids, which are now available in gravities from 1.59 to 2.95. This paper reviews preliminary results obtained from laboratory test work on heavy liquid separation of sylvite from halite. TEST WORK The heavy liquids used in the tests under discussion were chlorobromethane, with a specific gravity of 1.923, and dibromethane, with a gravity of 2.490. These liquids, completely miscible, were combined in the proportions needed to give a mixture having the desired specific gravity. Feed for the laboratory tests was mine-run ore screened to the desired mesh sizes. In conducting the tests, the sample was fed at a constant rate into a stream of heavy liquid and the mixture directed into a small separatory vessel. The float overflowed into a collecting pan while the sink collected in the bottom of the separatory vessel and was removed at the end of the test. Approximately 500 g of feed constituted a charge. Pulp density of the feed was kept low to prevent particle to particle interference in separation. With feed in the range of 8x100 mesh, a pulp density of under 10% solids by weight was found advisable. With coarser feed the pulp density could be carried as high as 15% solids. Time of separation was very rapid. In the case of 4x20-mesh material, separation was effected in 15 to 30 sec; with -10-mesh feed, separation required about 1 to 2 min. SPECIAL EQUIPMENT Since heavy liquids are toxic to varying degrees, all separatory work was carried out in a standard laboratory fume hood. It was noted that complete removal of fumes was not being effected; therefore the hood construction was modified, resulting in a completely satisfactory arrangement for heavy liquid test work. In the interest of safety, details of this fume hood are reported here. Unlike most fumes, heavy liquid fumes tend to settle and flow like water, rather than to rise like a gas. Working on this assumption, a standard water drain was installed in the hood. Across the front of the hood a 1-in. barrier was constructed. In the rear of the hood a false back was installed, with an adjustable sliding door on both the bottom and top of this panel. As shown in Fig. 1, the exhaust fan pulled a vacuum behind the barrier, sucking the heavy fumes from the bottom of the hood. Another addition was the drying box, shown to the right of the hood. This is simply a box covered on top with hardware cloth and connected by a 6-in. inlet to the hood. Sample trays made of fine mesh wire filter screens were found ideal for drying samples. With this arrangement, air flowed completely through the sample and all fumes were drawn into the hood. In use, it was found effective to cover with a

Jan 1, 1963

Maximising margins in today's competitive international commodity markets demands superior productivity. This requires more than simply selecting the best equipment. It requires efficient production and commercial processes together with management systems recognised as international best practice. This paper introduces an integrated way of working that includes management systems for successfully changing work practices and attitudes, developing managers and increasing accountability. It provides an improvement methodology that includes systematic involvement of people in true continuous improvement of processes for maximising productivity and safety while minimising costs. Even though the principles are proven in all industry sectors worldwide, they are not always used correctly. This paper provides examples of traditional performance measurement systems to show how managers miss opportunities to control and improve both production and supporting service processes. It also describes the basic methodology for correct use of the principles and provides examples of correct implementation of modem systems in mining. The charts from actual mining case studies will be elaborated upon in the conference presentation. This paper's main aim is to provide background material for the presentation by introducing integrated principles for building best practice management systems for superior productivity and safety - for higher margins.

Jan 1, 1996

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. We are referring here, of course, to properties inherent in the just solidified ingot and are not considering variations in properties caused by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. In plain carbon steels these elements are ordinarily not more than five: carbon, manganese, silicon, phosphorus, and sulphur. In alloy steels the special alloying elements also are specified and. determined. It might be thought that variations in properties due to such variations in ordinary chemical composition are to be expected, well understood, and hence not in need of discussion in this chapter. It will be considered here, however, that this phase of the subject is not always wholly clear. Furthermore, it certainly seems profitable to seek the explanation of anomalous properties in the ordinary chemical composition of the steel before looking into less well understood variables of open-hearth practice. It is sometimes surprising to learn that some puzzling variation in properties is caused merely by a variation in the ordinary analysis of the steel. This surprise is apt to be due not to general lack of knowledge of the effects of the composition of steel upon its properties but rather to the fact that we do not happen to have been previously much concerned with the particular property under consideration. For example, if we are accustomed to using S.A.E. 1035 bars for applications which depend chiefly on the stiffness, strength, and toughness of the steel in the as-rolled condition, we might quite logically develop the conclusion that variations in carbon content from 0.30 to 0.40 per cent are not significant. Then if we later have occasion to make heat-treated bolts of the same grade of steel, we may be surprised to

Jan 1, 1944

By Owen Collins

In surface mining, designing patterns to reduce the probability of flyrock and optimizing fragmentation through powder factor calculations are important for safe, efficient blasts. The designed powder factor is established for the blast once parameters such as burden, spacing, stemming, and powder column height are determined. In practice, these parameters are usually constant throughout a production blast with row-to-row burden and spacing. However, challenges can arise with the introduction of an open face. Many variables could necessitate the adjustment of the face row to optimize blast results. Variables include drill accessibility, challenges with toes, overhangs, and geology. The approach is often, but not exclusively, determining how to keep a consistent powder factor from the open face through the body of the blast. However, the solutions used vary case-by-case and rarely are two blasts the same. Technology has improved the ability to deal with challenging face conditions. 3D modeling with the aid of drones allows the application of angled holes to be more effective and simpler. This is just one instance where technology has improved blast results. This paper will present solutions to challenging face conditions. Thoroughly analyzing instances where challenging open-face variables were met with an effective blast solution could help provide insight as to what yields consistent blast results.

Jan 26, 2026

By Saulo Brinco Diniz

O alumínio e suas ligas por apresentarem uma série de vantagens, são largamente utilizados em diversas aplicações. O que mais reduz o campo de sua aplicação é sua baixa resistência mecânica, porém esta pode ser modificada através da adição de determinados elementos de liga e de processamentos termomecânicos adequados. Este trabalho teve como objetivo estudar a evolução microestrutural de uma liga de alumínio 7475-T7351 processada por laminação cruzada, e posteriormente submetida ao tratamento térmico de recozimento a 500ºC para recristalização, com tempos de encharque de 15, 30, 60 e 120 minutos. De acordo com os resultados apresentados, pode-se observar que a completa recristalização ocorreu entre os tempos de 30 a 60 minutos de encharque no tratamento térmico.

Oct 30, 2017

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

The Raub Gold Mines are situated approximately in the centre of the Malayan Peninsula in the State of Penang. Part of the area, now known as "Raubhole," was opencut some 800 years ago by the Mon Khmers, a Cambodian people, whose vestiges mark numerous outcrops in South Eastern Asia. With their decline and extinction the work was abondoned, leaving a large pond in a dense thicket of Beluka (secondary growth).From the year 1885 onwards the history of Raubhole and the water therein records a chain sale starting from an enterprising local "Rajah," who had "assumed" authority, to an equally wakeful Singapore Arab; thence through the agency of a "down-and-out" beachcomber to a hopeful Australian company in the "goldbrick" days. Subsequent catastrophe on a depleted stringer was followed by reconstruction; the deserved reward of a long mining life, and an output of nearly 800,000 ounces of gold. Owing to the loss of notes and data stored in Singapore, this paper is not as complete as it should be, especially in respect to its metallurgical phases. Apologies are therefore tendered in advance for any deficiencies which may be noted.The necessary regional geological data have been taken largely from the admirable investigation of the Raub area by J. A. Richardson, A.R.C.S., B.Sc., F.G.S., of the Malayan Geological Survey*, and, throughout the paper, months represent lunar periods of 28 days and money is expressed in sterling.MINING SECTIONSAs shown hereunder the reef system has been divided by nature into seven isolated sections, which have been of necessity worked as seven separate small mines. From north to south these are:-(a) Sungei Agas consisting of very shallow workings to the south of, and adjacent to, a granite-porphyry mass known as Bukit (hill) Kajang. This area has not been worked for many years.(b) Bukit Malaka which is also shallow.(c) Bukit Jalis.(d) Bukit Koman which, with (c) and (e), consitutes the main workings and which has possibly been determined in depth.(e) Anderson Section.(I) Raubhole Section.(g) The workings under Raub Village.

Jan 1, 1945

By Sanjeeva Latchireddi

The effective utilization of the energy in comminution devices depend on how efficiently the broken particles leave the breakage field as soon as they reach product size. In crushers the transport of broken particles smaller than CSS is done by gravity (vertical) thus allowing the energy to be applied to new particles. However, in AG/SAG mills, gravity becomes the energy field and the transport of particles is horizontal which needs a suitable discharge mechanism and has been found to have significant effect on grinding efficiency. The material transport in AG/SAG mills depend on how efficiently the discharge system (grate and pulp lifters) operates. Material transport plays a significant role on efficiency of horizontal grinding mills ? AG/SAG/Ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a Greenfield milling operation at Mirabela Mineração?s SantaRita Nickel operation located in northeastern part of Bahia in Brazil. This grinding circuit was commissioned in October 2009, which was designed as a typical SABC circuit to grind 4.6 mtpa (575tph) to produce a P80 of 125um with 10-12% ball charge in SAG mill. However, it has been operating as ABC circuit without any grinding media in SAG mill. The nameplate design capacity has been achieved in few days and has gradually increased to an average of +800 tph and still it is operating in ABC mode. The milling circuit commissioning resulted in small and relatively simple measures to rectify, which was reflected in the rapid commissioning of the milling circuit and it achieved the nameplate capacity within days. The Santa Rita grinding circuit consists of one 30?x 15.4? 8.5MW SAG Mill fitted with Outotec patented Turbo Pulp Lifters (TPL TM ) in close circuit with HP400 short head pebble crusher and one 20? x 28.4? 5.5MW Ball Mill in closed circuit with Warman cyclone cluster fitted with 10 x 26? CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimization, and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed. Keywords: Autogenous Grate (AG), Semi-Autogenous Grate (SAG, Turbo Pulp Lifter (TPL)

Sep 1, 2012