Search Documents

By C. R. Johnson, R. A. Greenkorn, G. W. Widner

This paper describes a short, simple well-testing procedure evolved from unsteady-state concepts to appraise wellbore damage in water-input wells. Input rates are changed at specific intervals over a 30-minute period and the wellhead pressure recorded at the end of each interval. From these data, the pressure drop due to the "skin" can be computed. This pressure drop in terms of psi/B/D of input rate is referred to as the "skin factor". Two of these variable-rate tests are required to determine change of wellbore damage and to evaluate well-treatment techniques. There are several advantages to the variable-rate procedure. The necessary data can be obtained with wellhead gauges and meters. There is little interference with normal operations. The short testing period eliminates many interpretative difficulties that come from interference from adjacent wells. The shut-in period required for standard tests before the plot of pressure vs log of time attains a straight line is often 12 hours or more. Such a time period is incronvenient, especially when a well must be tested repeatedly to evaluate change in wellbore characteristics. This variable-rate procedure has been successfully npplied to water-input wells in three fields. For some of the wells, skin factors were calculated from both the standard and the variable-rate tests. These results show good agreement. THEORY OF THE VARIABLE-RATE PROCEDURE In many waterflood input wells, the pressure in the wellbore differs from the pressure in the reservoir immediately adjacent to the well because of the restriction of flow through the skin of the well. If the true pressure of the reservoir at the well, p,, is that pressure which would exist in the well if no skin were present, and p,' is the actual pressure as measured in the well, this difference, is the skin effect. Fig. 1 shows the change in skin effect with change in flow rate. As the flow is reduced, the skin effect is reduced by an amount equal to the change in wellbore pressure minus the change in reservoir pressure. The equation of pressure change without skin using the point-source solution of the diffusivity equation is (after van Everdingen')

By M. D. Hassialis, Arthur F. Taggart

WARK1 observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility=product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith. The experimental work comprised. accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1946

By S. P. Singh

In order to simulate the operation of coal extraction machines, a portable workability instrument has been designed. Initially, the tests were performed with the instrument on modeling material, which were followed by in situ tests on coal in underground mines. The peak and mean cutting resistance and work done to cut a unit length of coal were determined for coal as well as modeling material. In addition, rebound strength and dynamic penetration tests were also performed in situ. On the basis of the cutting characteristics of coal, a "Workability Index" has been developed and its role in the judicious selection of coal cutting machines has been discussed. With reference to prior works and the strength characteristics of coal, it was found that the coal plow may not be suitable for the seams under investigation and the shearer seems to be the only choice. It has been observed that peak cutting resistance and the "Workability Index" in the case of coal as well as modeling material depend upon compressive strength. The peak cutting resistance exhibited certain dependence upon the Schmidt rebound hardness and dynamic penetration strength of coal in situ.

Jan 1, 1984

Thirty mixed cultures of microorganisms from soil, water and mineral samples from the Groote Eylandt Mining Company mine site were approximately three times more effective in biodegrading manganese dioxide (34± 18 mg Mn++/1/day) than sixteen purified strains (11 ± 10 mg Mn++/1/day) isolated from the primary enrichment cultures. Two pure bacterial genera identified as a Pseudomonad and a Bacillus, with an excess MnOz and nutrient, were able to dissolve 106 mg Mn++/litre/day in mixed culture compared with 29 mg Mn++/litre/day when grown separately.

Jan 1, 1983

By M. Brändström, R. Dube, J. Moyo, T. Perkins, G. Bermudez, L. Bartsch, C. Smith, R. Sorensen

The Kennecott Copperton concentrator is currently the bottleneck for the Kennecott operation and several projects have been initiated to increase throughput. This increase in grinding circuit throughput has resulted in a coarser grind size which has impacted flotation circuit recovery. Metso Outotec 300m3 forced air tank flotation cells are currently utilized in the rougher flotation circuit at the Copperton concentrator. Higher overall recoveries have been observed on the newer Outotec tank cells compared to the original 85m3 self-aspirated flotation cells they replaced. However, coarse particle flotation response on these large, forced air cells did not show encouraging results when compared to smaller previously installed cells. This coarse recovery loss has been attributed to the longer froth transport duration and transport distance on large cells (100m3 and larger). Cell manufacturers addressed the risks of additional coarse particle losses in large cells by installing concentric circumferential launders and crowders (also called center launders). These are designed to reduce froth transport time and distance in the last cells in rougher stages where low residual floatable minerals causes a lack of froth mobility. The center launders also increase froth crowding, which also helps to increase froth transport velocity and increases copper and molybdenum recoveries. A trial set of the center launder retrofits were installed on the last three tank cells in one of the parallel rougher flotation rows at Copperton. The launder retrofits were installed at the end of October 2020 and monitored until March 2021. This six-month trial showed statistically significant improvements in copper and molybdenum flotation recoveries through the rougher circuit.

Mar 2, 2022

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By Joel Ochoa, Miguel A. Montiel

El análisis metalográfico se usa en las industrias como herramienta para ayudar a identificar un metal o aleación, para determinar si una aleación se procesó correctamente, para examinar múltiples fases dentro de un material, para caracterizar imperfecciones tales como poros o impurezas, para observar daños o degradaciones y para hacer análisis de fallas. El método para hacer evaluaciones utilizado en el presente estudio es la microscopía óptica, que al igual que la de barrido electrónico con análisis de rayos X de dispersión de energía (SEM / EDX), logra buenos resultados al efectuar un análisis metalográfico.

Dec 31, 2018

By C. M. Rule

Stirred milling using either horizontal or vertical mills has made a rapid entrance into PGM ore and tailings concentrator flow sheets. Currently there are in excess of 40 units installed in either mainstream, ?MIG? or intermediate concentrate regrind, ?UFG?, applications in PGM, primary ore treatment plants or in tailings scavenging and reclamation treatment plants. This represents a total of approximately 70 MW of installed fine grinding equipment. This paper outlines the reasons why the technology take-up has been rapid and illustrates the advantages of this technology over conventional milling. Keywords PGM, platinum group metals, UG2, Merensky, platreef, stirred milling, MIG?mainstream inert grinding, UFG?ultra fine grindingof intermediate flotation concentrates, IsaMill?, Metso SMD?, Deswik, ceremic grinding media, QEMSEM, MLA.

Jan 1, 2011

By John Wilson

HARRY HINDS: Our first speaker today is Dr. John Wilson. Dr. Wilson is chair and Union Pacific/Rocky Mountain Energy Professor in mining engineering at the University of Missouri-Rolla. He has previously held senior management positions with Trans- African Mining Ltd., Anglo American Corporation, Consolidation Coal Company, Smith International Inc., Adams Resources Inc., and Golder Associates. John started his mining career as a coal miner in the coal fields of northern England. Dr. Wilson received his bachelor of science degree from the University of Durham, his master's degree from the University of Newcastle Upon Tyne, and his doctorate from the University of Witwatersrand, all in mining engineering. Today, Dr. Wilson is going to address the subject "Hiring Recent College Graduates Versus Hiring Experienced Mining Engineers." Please welcome Dr. Wilson. DR. JOHN WILSON: The advantages and disadvantages of hiring engineers directly out of school or those with some experience are often discussed among mining company managers. The choice is essentially dependent on the culture of each company, the company's maturity and strategic direction, and the growth or phaseout plans in vogue at the time of the decision. Generally, major, established mining companies employ entry-level college graduates and train them, introduce them to company culture, include them in a succession plan to replace retirees, fill vacancies, and provide management to direct future growth of the company. However, some large companies take a different approach. During restructuring, down-sizing, etc., some companies do not hire college graduates directly from school. Rather, they tend to recruit from other companies or absorb valuable personnel available following acquisitions or mergers. While this is a logical approach, it seldom provides for the future management and leadership needs of the company. A clear example of this failure is found when reviewing the hiring practices, or lack thereof, in the coal industry of the 1950s.

Jan 1, 1998

By M Akop, G Phillips, L Elliott

An estimation geologist has many tools in their kit and using the correct one for the job is vital for creating a useful model. Reconciliation is a key step to monitor the performance of a resource model and to ensure the correct tools have been selected and appropriate parameters are set. This paper presents an example of refining the estimation methodology for a Channel Iron Deposit (CID), resulting in an improved model. Rio Tinto Iron Ore (RTIO) CIDs are unique iron ore deposits located in the Pilbara region of Western Australia and contribute a significant volume to the world’s seaborne iron ore market. A problematic feature of these deposits is the irregular dispersion of clay pods that cannot be delineated with confidence within the resolution of the exploration drilling. Resource to grade control reconciliation showed an over-prediction of high-grade material in the resource model. A fresh approach was required to improve grade and tonnage predictions. Historically, clay pods were delineated using traditional wireframing techniques and estimated using ordinary kriging with hard boundaries. The new method utilised indicator kriging to estimate the probability of clay. Probabilities generated from the indicator kriging estimate were used as an additional weighting following the ordinary kriging of grades. Results showed indicator kriging improved global high-grade tonnes reconciliation, however, as expected, it did not improve the spatial prediction of clay. Based on improved reconciliation results indicator kriging has now been adopted as a suitable alternative for analogous CIDs at RTIO. These improvements benefit the mine planning process, but do not replace grade control models.

Mar 22, 2022

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural gas through high-pressure pipe lines. This report deals with that part of the study involving the design off pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By J. R. P. Aguirre

Minerales Monclova, S.A. de C.V. (MIMOSA) is owned by Grupo Acerero Del Norte (GAN). This company has 4 underground coal mines and 1 open pit to feed it?s steelmaking facilities located in the city of Monclova in the North of México in the state of Coahuila. The current underground mines are Mine 3, 5, 6 and 7 and the future projects are Mines 8 and 9. In the last years Mines 2 and 4 have been closed because they finished their coal resources. The remaining mines have bigger production and developments requirements in order to accomplish the goals of the company. The mines have been working in deeper and gassier areas. These conditions have required improvements in the ventilation design and methane control systems for all the mines. In some cases the ventilation of some of the MIMOSA?S mines has been increased 80%, and besides this, an intensive methane drainage program has been applied using horizontal in-seam boreholes and gob wells. The short-term ventilation plan includes the construction of 3 new vertical shafts with 5 and 6 meters diameter for Mines 5, 6 and 7 and the purchasing of bigger new main and backup fans for each one of these mines. One of these vertical shafts and the purchasing of the first 2 fans is already in process. This paper will explain the evolution and results of the ventilation and methane drainage systems in MIMOSA and the ventilation planning for the future years.

Jan 1, 2009

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By F. K. Mulenga, M. Lusambo

"Geometallurgical models are a strategic tool used primarily in planning, diagnosis, and process optimisation. This paper discusses the development of a predictive model for flotation recovery at Kansanshi concentrator in Zambia as a function of key operational parameters. Daily data for milling and flotation from the circuit processing the copper sulphide ore was analysed. This data, recorded over a period of one year of production, was collected from diverse sensors measuring semi-autogenous milling and flotation parameters. Statistical analysis showed that copper head grade, acid-insoluble, and acid-soluble copper, SAG mill throughput, ball mill load, and tonnage of feed material to the SAG mill in the -125 +63 mm size fraction contributed to the prediction power of the proposed empirical model by as much as 90%. Finally, a proposal was made for the development of a simulation model under MODSIM®, a flexible tool for mineral processing applications. This was to test the limitations of the empirical model for future refinement. IntroductionKansanshi is the largest copper mine in Africa and the world’s eighth largest copper producer, with a total of 253 272 t of copper produced in 2016 (Newall, 2017). It is located approximately 10 km north of Solwezi, the capital and administrative headquarters of the North Western Province, Republic of Zambia. The ore deposit consists predominantly of chalcopyrite and malachite with variable amounts of chalcocite, bornite, chrysocolla, and azurite. Because of the varying proportions of sulphide and oxide copper minerals, the ore is classified into three distinct categories: sulphide, mixed, and oxide ores. As such, three separate processing circuits are used to mill the ore down to a standard targeted grind size of 80% passing 150 µm before froth flotation and leaching.A lot of research and development has been done to improve the performance of the sulphide ore circuit at Kansanshi. Despite the research efforts and subsequent operation, the sulphide ore circuit did not attain the target recovery and grade for 2016, primarily because of the complexity of the orebody.The constant drive to achieve the set production target of recovery and concentration grade after froth flotation motivated the development of a tool for the prediction of recovery. The anticipated benefit is not only to enable the plant to apply corrective actions when needed, but also to make a tool available for the quick assessment of the plant performance of the. For that purpose, data spanning June 2016 to May 2017 was analysed, cleaned up and curvefitted to an empirical model. In doing so, key parameters were determined and calibrated to represent the behaviour of the plant."

Nov 1, 2018

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By I. M. MacGregor

This paper discusses the possible use of petrological data and proximate analyses in the prediction of cutting forces for coal. It is restricted to the development of univariate predictors based on data from thirteen collieries in five major Transvaal and Orange Free State coalfields and three coal provinces. The aim of the work was the identification and development of the best predictors of mean peak cutting force and Hardgrove grindability index from among the independent variables evaluated. The data, which were obtained by use of the penetrometer developed by the Chamber of Mines Research Organization, were processed according to the SPSS computer package. The analysis revealed reasonable correlations between the Hardgrove grindability index and (1) the volatiles and vitrinite content in the Vereeniging-Sasolburg and South Rand Coalfields, (2) the contents of vitrinite, vitrinite plus exinite, and minerals plus inertinite in the Eastern Transvaal Coalfield.

Jan 1, 1985