Search Documents

By Foster Fraas

MOST commercial electrostatic separators utilize the electrical property of conductivity, but although based on the same principles, they are constructed in a variety of forms, a common one being the simple roll type. Some information obtained during an investigation of that type of separator, and which indirectly is applicable to other types, is presented here. NUMERICAL RELATIONSHIP In Fig. I material discharged from hopper 6 is fed onto grounded rotating roll 2. Electrode 3 is at a high electrical potential with respect to roll 2, and any conductive particle in contact with roll 2 therefore acquires an electrical charge of such polarity that, when present in the electrical field, the force on it is in the direction of electrode 3. A detailed description of the charging by conductance as utilized in electrostatic separators may be found in a previous publication.1 As a result of this force, the path of the projected particle is changed in increasing amounts in the direction toward region C as the magnitude of the charge is increased. With the dividing edge 4 the projected particles may be divided into two fractions -those in region C designated as "deflected" or " deflectant " and those in region B designated as "residue." When material is passed over the roll only once, a complete separation is seldom obtained, therefore most commercial separators contain several roll-separator units in [ ] series, and some practical machines use as many as 12. In this paper a "pass" means the passage of material over a single-roll unit. The procedure is to repass either residue B with a low potential on electrode 3 or deflectant C with a high potential on 3. Most electrostatic separations follow a flowsheet of roughing and cleaning either the concentrate or the tailing, on both. In a specific instance, a dry, heated mixture of wet cleaned chromite and garnet from an

Jan 1, 1942

By D. A. Dahlstrom

In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in [Fig. 4]. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in [Fig. 4]. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensers, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89c/t (81c per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed.

Jan 1, 1984

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By Toshiyuki Kawai

Copper concentrate smelting directly in P-S converters was started at Onahama Smelter in 1983. Thereafter, the tonnage of concentrate smelted through the P-S converters increased, such that by 2002, it equaled the tonnage smelted through the reverberatory furnaces. In 2003, 56% of the total copper concentrates treated at Onahama Smelter were processed directly through the P-S converters. Technical improvements are reviewed and advantages of direct smelting in P-S converters are reported.

Jan 1, 2005

By A. F. Taggart

OLIVER C. RALSTON, Salt Lake City, Utah (communication to, the Secretary*).-This paper has appealed to me as being one of the most lucid, well-connected and complete papers on this subject which has been published. To be sure, the concepts called upon in an explanation of the flotation process by these authors are mostly old ones which have been more or less discussed in previous literature, but they have nevertheless been assembled in a most constructive and suggestive manner. We find a new contribution to flotation theory in the effect of fine particles increasing the viscosity of the interfacial film between a liquid and a gas. This phenomenon has been variously hinted at but never definitely stated in accepted scientific terms. The discussion of "contact angles". is very clear and will doubtless be welcomed by those who have not had the opportunity to investigate the literature on this subject, but it is unfortunate that the "hysteresis of the contact angle," observed by Sulman and reported some years ago, is not mentioned or explained. A few other points need discussion in order to call attention to the fact that, while this paper is the best discussion of the subject which has yet appeared, all of the truth has not yet been told.

Jan 12, 1916

By S. Becker, M. Gruner

"Microstructure stabilized crushed rock salt is a newly developed backfill material for infrastructural openings in HAW repositories. The motivation for this research is based on the fact that the microstructure stabilized crushed rock salt is considered to be superior to the currently used crushed rock salt. The avoiding of settlements with a simultaneous 100% backfilling of openings, early stabilization of the geological barrier and low permeability (< 10-14 m²) are the main improvements. With the newly developed backfill material, the gap between the crushed rock salt and the saliniferous composite backfill materials is closed. Due to the minimized amount of a binding agent, the material will still be easy to handle like a bulk material, yet guarantees close to 100 % backfill success without any settlements. This is accomplished with a long-term stable re-mineralization that is formed by the components of the binding agent. INTRODUCTION The permanent storage of high active waste in underground geological formations (HAW-repository) is the labored method in Germany as well as internationally. Experiences have been made over the last decades, e.g. in the Waste Isolation Pilot Plant (USA) and the mines Morsleben and Asse (Germany). For this purpose salt formations are preferred as host rock due to the adequate heat conductivity, creep capability, and low permeability. In order to maintain the low permeability of the host rock and to avoid any contact of the stored waste with the biosphere, the formation of flow paths has to be prevented. The cavities which have been mined for the purpose of waste storage have to be backfilled with material that is alike to the host rock. Therefore crushed rock salt is considered as an appropriate backfill material. Crushed rock salt is a bulk material that is produced by mining saliniferous formations. This material is mainly used in underground repositories as a dry backfill that is brought into the cavities by the use of mechanical (loading machine, slinger machine or scraper) or pneumatic energy (pneumatic stowing). In Germany it is intended to use dry crushed rock salt with a maximal grain diameter < 64 mm for backfill in a future repository in saliniferous formations. With this method applied, the porosity of the backfill is up to 35 % [1]."

Jan 1, 2015

By Robert L. Somerville

As more phosphate deposits are discovered and new mines are developed, the necessity of critically evaluating various rocks for phosphoric acid production recurs ever more frequently. This need is accentuated by the increasing number of, fertilizer plants being constructed on deep water at various locations to serve world markets and to take advantage of locally-available sulfur or sulfur-bearing ores. A major proportion of all phosphate rock mined is consumed by wet-process plants and this acid in turn is consumed, usually captively, in the manufacture of fertilizer. It is apparent, therefore, that the first question asked by the developer of a new deposit is - How will it work in a wet-process plant? and conversely, when developing a deep water, project, one of the early studies required is - Which of the available rocks shall we use? What is the correct price to pay? How do we compare one rock with another? The economic importance of even minor aspects of these questions

Jan 1, 1966

By Donald G. Foot

The Bureau of Mines, U.S. Department of the Interior, devised a direct flotation method for treating low-grade carnallice (KC1.MgC12. 6H20) and sylvinite (a mixture of KC1 and NaC1) ores characterized by a high content of water-insoluble impurities. The procedure consists of (1) flocculation-depression of the insoluble slimes, (2) decomposition leach (carnallite only), (3) potash rougher, cleaner and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid-phase KC1 from carnallite ore and 79.7% of the KC1 from sylvinite ore in final products containing 60.5% and 60.9% K20, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1981

By Dawei Yu, Kinnor Chattopadhyay

In the nickel industry, molten slags produced from a Pierce-Smith converter contain significant amounts of valuable metals in the forms of oxides and physically entrained matte droplets. A slag cleaning step, which takes places in an electrical slag-cleaning furnace, is therefore required to recover the valuable metals as a common practice. Utilization of a waste material from aluminum industry (i.e. spent potlining) as a flux to improve the slag cleaning in terms of both the metal recovery and the operation efficiency was studied by simulation with FactSage program. Results show that the addition of SPL could substantially reduce the slag viscosity due to its fluoride values, thus accelerating the settling of matte droplets. The carbon value in the SPL could also help increase the metal recovery by reducing the valuable metal oxides followed by settling.

Jan 1, 2015

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By Mo Jadbabaei, Scott Harrison

There is very limited information available regarding the air pressures, flow rate, and velocity profiles in blast hole air drilling applications. Currently, many people are using incompressible flow correlation to calculate the bailing velocity. In this article, air pressure, flow rate, and velocity profiles are calculated using compressible flow theory. The airflow at the bottom of the hole is simulated using the jet flow theory. The concept of choking condition is introduced, and it is concluded that the velocity at the nozzle exit cross section cannot exceed sonic velocity. The minimum pressure required for achieving choked condition at the nozzle cross section is calculated. Choked and overchoked flow conditions at the nozzles are examined, and the maximum achievable cleaning power is correlated to the nozzle size and pressure.

Jan 1, 1999

By Floyd B. Bowen

Pumping methods are used, almost exclusively, to transport materials in the mining, beneficiation and chemical processing of phosphate rock in the Florida phosphate pebble field. Matrix pumping systems capable of pumping 15,000 g.p.m., transporting 15,000 long tons (dry) per hour, are now in use. They utilize 16-by 48 Yz -in. pumps, driven by 1.250-h.p. motors, discharging into pipelines 20 inches .in diameter .and sometimes several miles in length. As an average, it is necessary to pump 3 tons of matrix to the beneficiation plants, and to dispose of 2 tons of sand tailings and clay as waste, in order to produce 1 ton of shipping-grade rock. The washers and flotation plants, where the clay and phosphate and silica particles are separated, require the movement of large volumes of slurries with densities ranging from 2-3 per cent to 45 per cent solids, by weight. Extensive waste disposal systems require the pumping of dilute clay slurries in quantities of up to 50,000 g.p.m.,

Jan 1, 1963

By E. L. Garton

Bureau of Mines routine crude-oil analyses of 88 samples from 60 fields are presented in this report. Similar analyses from other fields in California have been published in previous reports listed in the appendix, page 52. Yearly production of crude oil in California and the percentage of United States production represented by California production for 1948-54 are given in table 1. [ ] Analyses in this report are of samples from the fields listed in table 2, with production data for 1953, cumulative production through 1953, and year of discovery of each field. Information regarding the source and general characteristics of the samples is included in table 3 with a summary of analytical and computed data.

Jan 1, 1956

By Carlos Carnurri

A characterization of mechanical properties of fire refined copper has been done in order to link ductility with oxygen content. The results show four different copper mechanical behaviours as temperature increases, where the oxygen con- tent, as Cu20 segregated, has a deleterious effect on ductility. It is concluded that until 500 ppm oxygen content, the fire refined copper could be rolled without remelting for deoxidation. Also a subsequent cold rolling could be done without intermediate annealing.

Jan 1, 1994

By C R. Stanley, D Lawie

The measurement of error in assays collected as part of a mineral exploration program or mining operation, including errors introduced during sampling, sample preparation, or geochemical analysis, historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation. CITATION:Lawie, D and Stanley, C R, 2012. Average relative error in geochemical determinations - Clarification, calculation and a plea for consistency, in Proceedings Sampling 2012 , pp 181-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

By S. K. Gilman, V. E. Hugo

A common problem encountered in the mineral sands industry is that the mineralogical measurements used in defining the resource are not readily converted to metallurgical recoveries, which are used to predict the quantity of the final products. The problem stems from the different objectives of the exploration and metallurgical assessment programmes, and is often compounded by the use of different laboratory techniques and mineral definitions. Common mistakes include the misapplication of routine analysis, incorrect interpretation of mineral recovery, the confusion of mineral recovery with product yield and inconsistent definition of the same mineral. Experience has shown that unless these potential mistakes are identified, the measurement techniques used during exploration and metallurgical assessment are not compatible, often resulting in large errors in the prediction of mineral production. There are no easy solutions to the problem, as there is no universal assay technique which can cost effectively characterize all the mineral sands resources. The recommended course of action will therefore require several iterations to optimize the assay technique to suit the resource. Fundamental to the success of the measurement technique is the understanding of the mineralogy, its behaviour during mineral processing and the quality requirements for the final products.

Jan 1, 2003

By H. R. Weischedel

The art of wire rope inspection has advanced rapidly over the past decade. Present electromagnetic (EM) wire rope inspection instruments provide an important and often vital element of wire rope inspection. Some instruments are easy to operate and offer simple and clear data interpretation. Simultaneously, wire rope inspection and retirement standards are becoming simpler and more lucid. Future guidelines will he easy for inspectors to apply and for rope operators to fulfill. The thrust of evolving regulations is clearly toward periodic EM inspections supported by visual inspections. These development sallow even moderately skilled personnel to perform EM inspections of wire ropes. Therefore, it is now possible and cost effective for wire rope users to have EM and visual inspections performed by in-house personnel. In-house EM inspections have many advantages and offer an excellent return on the initial investment. Since EM inspections can detect rope deterioration in its beginning stage, wire rope users recognize that they are an effective preventive maintenance tool. For instance, the early detection of wear or corrosion allows immediate corrective action. This can easily double, or even triple or quadruple, the service life of a rope.

Jan 1, 1991