Search Documents

By David Cornell, D. L. Katz

Procedures for computing turbulent flow of gas in steady state near the well bore and a graphical method for predicting unsteady state laminar flow at distances from the well have been combined to compute pressure gradients in gas reservoirs. Methods are discussed for predicting single and multiple transients at constant flow rate in an infinite reservoir, predicting constant How rate. in a finite reservoir, reproducing and interpreting back pressure test data, and prediction of the behavior of a closed-in gas well. An example of the graphical method is given for a single transient and the results are compared to a published analytical solution. A typical calculation of the pressure gradient in a reservoir and the production of gas is made .starting with data from a hack pressure test. INTRODUCTION The calculation of pressure gradients throughouse a ga-reservoir at any point in its production history is a complex problem involving turbulent flow near the well bore and unsteady state flow of the gas from the reservoir. The problem is complicated further by the variety of boundary conditions that may be imposed upon the flow. Such boundary conditions include finite or infinite reservoirs. constant or variable rates of production, constant or varying bottom hole pressures, complex initial pressure distributions throughout the reservoir, and pressure maintenance through cycling. In addition to these problems there are the practical difficulties associated with natural gas reservoir analysis These might include: (1) variation. in the permeability and porosity throughout the formation. (2) variations in the thickness of the formation, (3) communication of the producing formation with other producing zones. (4) radial variations in permeability due to influx of drilling fluid. acidizing. or the buildup of liquid in the formation around the well, (5) partial penetration of the producing zone. (6) water flood, and many others. These problems will be considered eventually. In the mean- time, it is necessary to present methods of handling the case of radial flow through a homogeneous, regular, producing stratum to a single well uncomplicated by other factors. The idealized case of steady state, radial flow from a natural gas reservoir was studied by Elenbaas and Katz5 and by Mac-Koberts.' An analysis of the unsteady flow of gases through porous media has been made by Aronofsky and Jenkins' for the one dimensional laminar case with the boundary conditions of constant downstream pressure and uniform initial pressure. Solutions for the partial differential equation for unsteady state radial flow of liquids through porous media have been given by Van Everdingen and Hurst" for the constant bottom hole pressure and constant production rate cases for laminar flow in a reservoir initially at a constant pressure. The analogous heat transfer equation has been treated by Perry and Berggren9 for the case of quenching a cylindrical hole in an infinite medium to a constant temperature. The back pressure curve, which involves the variation of the bottom hole pressure as it is determined by the behavior of the reservoir as a whole. has been studied by Rawlins and Schellhardt,10 Binck-lev,' Baumel and Breitung,' and others. No complete. adequate treatment has been given for the unsteady state, radial flow of gases into a cylindrical hole from a porous medium with or without the presence of turbulent flow and for any set of boundary conditions. If one relies only on analytical solutions of the basic equations, a new solution must be obtained for each new boundary condition. Furthermore, the complexity of the mathematical expressions for boundary conditions other than the very simple cases limits the use of analytical solutions. Graphical methods exist, however. that are general in nature, accurate, and readily employed. The analysis of steady and unsteady, laminar and turbulent, radial flow for various boundary conditions with application to specific natural gas well problems by means of graphical procedures forms the content of this paper. STEADY STATE RADIAL FLOW EQUATION FOR LAMINAR AND TURBULENT FLOW A steady state radial flow equation for laminar and turbulent flow through unconsolidated sands has been given by Muskat as discussion of the work by Elenbaas and Katz.5 This equation is based on the properties of unconsolidated

Jan 1, 1953

By V. J. Driscoll

A method is given for checking pore volume reserve estimates and transient water inflzix factors utilizing early well performance. Principal applications are based on the observation that there is a convenient transient time-range in terms of well spacing in which observed pressure drop will give a good indication of fluid-in-place. Primary quantity determined is a porosity-feet value applicable in the vicinity of an observation well. Checks on porosity or net pay thickness and permeability values also are obtained. These are particularly valuable in improving quality of interpretive factors entering into pore-volume reserve determinations for larger fields. In smaller fields, direct determination of total field reserves and approximate location of boundaries may be made in some cases. Well interference and production data plus a build-up curve on the observation well are needed. The build-up curve may be taken at any time. Field applications are given. The method can be applied with the completion of the second well on a new discovery or to older reservoirs by major changes in withdrawal rates from a local area. Appropriate test length permits results to be obtained with equal accuracy on widely spaced wells. Criteria for optimizing test conditions are given. Provision is made for various boundary and well effects including incomplete observation well build-up. INTRODUCTION Due to low quality data, initial pore volume reserve and water influx estimates may often vary by a factor of two or more from results obtained at a later date. Unfortunately, by conventional methods, more reliable answers from performance usually are not available until after most significant economic decisions have been made. Furthermore, in older reservoirs, uncertainties may still exist as to original oil-in-place, recovery factors and residual oil saturations due to incomplete or inaccurate performance data. This paper outlines situations and appropriate arrangements of basic transient theory whereby well interference data can be utilized to improve the quality of estimates under certain conditions. In addition to production data on offset producers, key information required is a measured pressure drop at an observation well, corrected for any incomplete build-up due to previous production, plus a formation capacity value derived from a conventional pressure build-up plot on the observation well. The method, as outlined, is strictly applicable only to a horizontal single-layered system of uniform rock characteristics containing a homogeneous fluid of low and constant compressibility. However, under the set of test conditions devised, requirements can usually be relaxed so that it should be applicable to most low permeability gas, water and undersaturated oil reservoirs. This is an area where more reliable information is certainly needed. BASIC CONSIDERATIONS A, B, C and F as subscripts or in the text refer to producing Well A, observation Well B, a more remote producing Well C and field boundary F. Combinations such as AB refer to distances and dimensionless times in terms of distances between these points, while single letters refer to distances and dimensionless times in terms of the well-bore or field radius. Equations covering definitions of quantities and complex situations are given in the Appendix. Key equations in practical units are given in Table 2. Transient Pressure Behavior Fig. 1 illustrates pressure drop at Point B with time due to initiation of a constant rate of withdrawal from Point A. This is shown as since a quantitative under-

Various steps, and complete sequences, for the recovery of lead and zinc from a mixed sulphide concentrate, high in silica and pyrite, have been tested.Oxidation steps of roasting in air or in a sulphating atmosphere and use of aqueous acidic, ammoniacal, and near neutral oxidation media were compared. Oxidation roasting or use of acidic media appeared most useful. Procedures for dissolution of zinc from calcines using sulphuric and sulphurous acid to avoid silica gelation problems are compared and a direct leaching procedure with sulphuric 'acid at controlled pH shown to be the most useful.Methods for the removal of germanium, nickel, and magnesium from zinc sulphate solutions prior to zinc electrodeposition were tested. The recoveries of zinc from ammoniacal solutions by electrolysis and distillation are compared.The dissolution of lead compounds from the residue of zinc extraction by amine and ammoniacal ammonium sulphate (AAS) solutions Was tested. Lead, sulphide was precipitated in filtera'ble form from AAS solutions. The reduction of lead sulphate to lead sulphide with sulphur was difficult, but possible. The various steps were used to deveiop five complete processing sequences, of which two were shown to be technically feasible and have potential economic viability.

Jan 1, 1975

By P. Mattar

The geotechnical importance of studying fluid flow through porous media and soils in particular, becomes evident when dealing with groundwater movement in surficial geomaterials that can be initiated by hydraulic gradients that develop during construction activity, groundwater extraction, impounding of reservoirs and groundwater recharge during adverse climatic events. In a geotechnical context, rocks are regarded as virtually impermeable materials, with comparatively greater resistance to flow of water through their pore structure. The importance of the permeability of rocks comes to the forefront when deep geologic formations are used in geoenvironmental activities for disposal of hazardous and toxic materials. The permeability of the rocks encountered is of critical importance to these geoenvironmental activities since the movement or transport of the hazardous materials during their eventual release will be largely governed by the permeability characteristics of the geologic formation. The estimation of the permeability characteristic of geologic formations is a non-trivial exercise since the measure of permeability can be influenced by the scale at which the measurement is made. Regional-scale and borehole-scale estimates of the permeability can be greatly influenced by the inhomogeneities, including fractures, fissures, solution channels and other anomalies that are present in naturally occurring geologic media. These anomalies are considered to be site specific and can only be determined in a reliable fashion by either conducting tests at the appropriate scale or in the regional-scale through inverse analysis of tracer movement patterns in rock masses. The estimation of the permeability of intact units of a geologic medium has important geoenvironmental applications in connection with storage of wastes since the units in which repositories will be located should be sparsely fractured and the sealing of the fractures and fissures are a prerequisite to developing an efficient solution for storage. The intact permeability of geomaterials is therefore regarded as an important property that influences efficiency and reliability of geoenvironmental solutions for deep geologic disposal. The permeability of geomaterials such as concrete and cementitious grouts are also important to many geoenvironmental and infrastructure applications where durability of structural materials in general and cements used for sealing deep boreholes and other access shafts employed in waste management endeavours is influenced by the permeability characteristics of these materials

May 1, 2009

By Hideki Minoura

"Two novel electrochemical techniques for the preparation of highly crystallized CdS film have been presented. One is cathodization of a conductive substrate in an acidic chemical bath containing cadmium salt and thioacetamide, where electroreduction of proton at small current densities induces a growth of highly crystallized CdS thin films, whose growth is not disturbed by the reactions in the solution phase. The other technique is electoreduction of aqueous Cd2+— SCN complex. An advantage of this technique lies in no formation of solid particles in the bulk, of the bath.IntroductionIn recent years much attention has been paid to materials preparation by solution processing because of its advantages in lowering the cost as well as the stress to the environment, as compared to the conventional gas phase techniques which unavoidably require high temperature and/or vacuum. We have been trying to explore novel techniques for preparing functionalized compound semiconductors by aqueous solution process. Semiconductors which we have been mainly focusing on are CdS and ZnO, which are important semiconductors finding applications in various devices. In the present paper, some of the techniques that we have recently established for the preparation of highly crystallized CdS will be presented.Methods of the CdS film processing in solution phase (wet process), which have been reported so far can be divided into two major groups; one is chemical bath deposition (CBD) in alkaline solution containing Cd2+ and thiourea 1)4) and the other is electrodeposition (ED) in acidic solution containing Cd2+ and thiosulfate ions - 5)-8) or organic solutions containing dissolved sulfur 9)-11)."

Jan 1, 2000

By M Khanal, J Qin, B Shen, Y Duan, X Luo

Gaining confidence in interpreting rock and strata properties of the coalmine roof is necessary for design, maintenance, modelling and optimisation of roadways supports. One of the key causes of roadway instabilities experienced in underground coalmines is an extreme variable nature (thickness, competence, discontinuities etc) of the coalmine roof. Normally, the thickness and strength of the roof are characterised with the geotechnical and geological data gathered from exploration boreholes, which are drilled often at considerable distances apart. This limited data cannot capture localised geological variations in the coalmine roof. With this background, this paper explores feasibility of using measurement while drilling concept to perform geotechnical characterisation of the coalmine roof. The parameters, for example, penetration rate, rotary speed, torque, sound, vibration, obtained during the drilling process can provide valuable insights into geotechnical properties. The paper describes the progress of the experimental work conducted at the laboratory on synthesized concrete samples representing various rock strata using a field-scale drilling machine. The samples with and without interfaces have been tested to replicate various underground roof strata. The signals returned from the drill machine, as the drill bit passes through the layers, have been analysed and interpreted to characterise whether the drill response data can differentiate various strengths associated with the rock layers. The initial laboratory results are promising as they show distinct responses of the various sample blocks in a controlled environment. The drilling data can differentiate the synthesized rock samples and detect ‘signatures’ of the roof strength variability and delineation of lithological interfaces (transitions). The weight and torque on the bit vary and show dependency on the strength of the blocks.

Nov 29, 2022

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

By J. W. Stickney

"On July 1, 1977 Hudson Bay Mining and Smelting Company Limited announced the commencement of construction of a 3800 ton per day concentrator at Snow Lake, Manitoba. Snow Lake, a community of 2200 people, is located 130 road miles from the main metallurgical plants at Flin Flon.The design, detailed engineering and equipment selection for the project was awarded to Wright Engineers Limited of Vancouver, B.C., who would be working in close liason with Hudson Bay Mining personnel throughout the project.The feasibility of constructing a metallurgical plant in the Snow Lake area, in addition to the concentrator at Flin Flon, had been under study since 1964 with plants of varying capacities and designs being considered. Each successive study recommended a plant of increased capacity and sophistication and finally upon an in-depth study in 1976 of ore reserves, freight rates and operational benefits, the construction of a 3800 ton per day copper-lead-zinc concentrator appeared highly benificial."

Jan 1, 1981

By Alberto Bruce

El objetivo del estudio repara sobre el equipo, las condiciones del subsuelo necesarias, y la performance obtenida tras perforar con un medio gaseoso un posible yacimiento de petróleo en la costa Norte Peruana. Como consecuencia de dicho proceso, se muestra que la técnica de perforación es superior a la técnica de perforación con lodo, puesto que logra beneficios como una mayor velocidad de penetración, mayor avance por broca, eliminación de costo de materiales por lodo, etc.

Jul 20, 1955

By R. M. Scafe

Although hydrogen has been intensively studied in its relation to steel quality, the methods of sampling and determinations are still open to question. It is true that various procedures have been proposed but actually there has not been sufficient agreement to establish a common base from which to work. As a result, it is difficult, to say the least, to correlate the reported results of some of the investigators in this field. The present symposium, premised on methods rather than effects, should prove of considerable value. For the purpose of this discussion two methods of sampling and analysis will be considered. First, sampling of molten steel in the ingot mold by use of an evacuated tube and cylinder using conventional methods of analysis for the gases collected; second, analysis by vacuum extraction involving the use of heating equipment and the determination of the amount of hydrogen evolved from solid steel samples by measurement at reduced pressures. Both methods have been used at Duquesne Steel Works and it is believed that either may be used with considerable benefit if the limitations of each method are recognized. Evacuated Tube and Cylinder Sampling devices for gases in molten steel suggested by various investigators range from very cumbersome and complicated devices to the relatively simple evacuated tube and cylinder used by Soler for deter- mining the CO content of the bath. This latter device was adopted (Fig. I) and modified to meet conditions at Duquesne Works. The principal modifications were in placing the cylinder at the side of the tube and the use of a sleeve on the immersion end of the tube. The first modification was made so that the cylinder could be readily detached and taken to the laboratory; the second, because of the difficulty encountered in obtaining an airtight seal after sampling and because of our practice of re-using the tube. Rigid control of the method of sampling and of the handling of the sample according to plan are of primary importance in hydrogen determinations. This applies to both the sampling of molten steel and the determination of the hydrogen content of cold steel samples. Except for a few preliminary samples taken from spoons, all work on molten steels using the evacuated tube was confined to the sampling and analysis of molten steel during the pour. As mentioned, uniformity of sampling was a basic consideration. As a result, every effort was made to follow definite sampling techniques and procedures. These included control of the depth below the surface from which the sample was taken, the timing between the shutoff and taking of the sample, as well as maintenance and care of the equipment. The distance below the surface at which the sample was taken was readily controlled bv means of a crosspiece and centering device attached to the tube. The steel was poured into the mold to the hot-top junction, the tube was then lowered into the 75

Jan 1, 1945

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facility to research on the fundamental tats of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, out Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing edit has an advantage over en active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin September 1935, with a crew of four laborers under a resident engineer. The laborers were recruited from, nearby farms, and. although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

0PINION was general that this year's meeting of the Institute of Metals Division was one of the best in its history. In addition to its full and exceptionally fine program of professional papers, there were several other features of general interest-an in-spiring annual lecture by Dr. Cecil H. Desch which appears in abstract elsewhere in this issue, Mr. Sing-master's talk on the zinc industry at the annual dinner, and the presentation of the James Douglas Medal to one of the members of the Division, Dr. Zay Jeffries. Four technical sessions of the Division were held, dealing respectively with zinc, copper, aluminum, and general metallography, and in addition there was a joint session with the Non-ferrous Metallurgical Committee of the Institute. All of the papers presented were at-tended with much interest and followed by considerable discussion. The papers on plastic deformation of zinc by Messrs. Mathewson and Phillips, Romig, and Hoyt were of particular interest and awakened an extended discus-sion. They well illustrated the progress which is being -made today in the understanding of the mechanism of flow of metals, and the ingenuity of the authors in their crystallographic method of attack of this difficult problem was quite generally admired. A very old subject was treated in a modern way by Messrs. Corson and Bain in two papers on the harden-ing of copper and copper alloys. There has always existed a myth that the ancient Egyptians were masters of an art not possessed by ourselves; viz., that of hard-ening copper. This myth must have been quite defi-nitely dispelled in the minds of all those who listened to this admirable paper. Mr. Corson has applied the modern art of precipitation hardening to this old prob-lem with substantial success, employing small amounts of chromium, nickel, silicon, and cobalt for this purpose. The commercial application of these very important .developments of Mr. Corson is being actively investi-gated at the present time.

Jan 3, 1927

By Alan Morris

IMPINGEMENT attack, as one of the types of corrosion suffered by condenser tubes, has been given a prominent place in corrosion literature of recent years. It has been reproduced and studied in carefully controlled laboratory tests. Much has been learned of its mechanism, and of the effects of variables such as temperature, amount of air, size of bubble and water velocity. Incidentally the technical public has been given comparisons between the behavior of some few metals under various conditions of impingement attack. The tests recorded here were undertaken in an effort to find at least some sort of qualitative answer to questions which arose occasionally as to the relative resistance of various alloys to impingement attack, and which could not be answered by reference to the literature. The final decision to start work on the problem was influenced in large measure by the nature of the water available in this particular place. The mill of the Bridgeport Brass Co. is located on the Pequonnock River at Bridgeport, Conn., within two miles of its mouth. The water is much like many other estuarine sources which are used in condensers, and which cause particularly severe corrosion. It seemed a most suitable water to use in such tests. As the work progressed an important seasonal variation was noted. The purpose of this note is to record this seasonal effect. The results of individual tests are given only incidentally.

Jan 1, 1931

By W. C. Brice

Minnesota contains a major copper-nickel resource. In anticipation of requests by industry to develop this resource, the Minnesota Department Of Natural Resources has developed a computerized resource inventory and analysis system, MINESITE This extensive database is available to regulatory agencies as they evaluate mining proposals as required by law. The Resource Analysis phase of the project allows state mining policy decisions to be evaluated in terms of long-range effects on Minnesota's mining industry and environmental and land use impacts. The analysis also allows for comparison of proposed mine facility sites to a representative range of sites in terms of engineering, site characteristics, and land use and environmental impacts.

Jan 1, 1980

By E. H. Jr. Dix

THE success of the Charpy impact test in the steel industry has led those interested in aluminum alloys to investigate the possible applica¬tion of this test to aluminum and its alloys. In this paper are set forth the results of a few preliminary tests made at the Lynite Laboratories of the Aluminum Manufactures, Inc. In order to study more thor-oughly the significance of the Charpy test, slow-bending tests have been made duplicating the arrangement of the impact machine. Tests have been made on both notched and unnotched specimens of a series of copper-aluminum alloys. APPARATUS The standard American-made Charpy impact machine delivering a blow of over 200 ft.-lb. was- much too large to test aluminum-alloy specimens of the same type used for steel, so that it was necessary either to adopt a larger specimen or to have a special light-weight hammer made. Since there is no known relation between specimens of different sizes, even though geometrically similar, it was decided to adhere to the 10 by 10 mm. specimen. Accordingly, Sauveur and Boylston, the American makers of the machine, were asked to construct a special light-weight pendulum adapted to their standard machine, this pendulum to have one-tenth the capacity of the standard. The writer wishes here to acknowledge his indebtedness to Mr. H. M. Boylston for the personal interest and care exercised in constructing this pendulum. The machine with, the light-weight hammer in place is shown in Fig. 1. It is mounted on a concrete foundation with the concrete covering the flange on the base of the machine. Vibration is further prevented by four 5/8 -in. (15.8 mm.) foundation bolts. The large standard hammer shown against the wall was also used for some of the unnotched bars that requited more than 20 ft.-lb. to rupture.

Jan 4, 1920

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006

By H. J. Ramey

Conventional calculation of total system isothermal compressibility for a system containing a free gas phase involves, among other things, evaluation of the change of oil and gas formation volume factors and the gas in solution with pressure. Preferably, this information should be obtained from laboratory measurements made with particular oils and gases. Often, experimental measurements are not available. In this case, it is necessary to obtain pressure-volume-temperature relationships from general correlations such as those of Standing' for California oils. In order to speed estimates of compressibility, generalized plots have been prepared of the change of both oil formation volume factors and gas in solution, with pressure from Standing's correlations. A generalized plot for estimating the change in the two-phase (oil and gas) formation volume factor with pressure is also presented. Usually, the effect of gas dissolved in reservoir water upon the total system compressibility is neglected for gas saturated systems, due to the low solubility of gas in water. Results of this study indicate that the increase in total system compressibility caused by solution of gas in water is often as large as the compressibility of wafer, and can be magnitudes larger for low pressure systems. Generalized results for estimating the change of gas in solution in water with pressure are presented in tabular and graphical form. INTRODUCTION During the past decade, pressure build-up and drawdown techniques have gained an important place in reservoir engineering. Build-up and drawdown analyses are only two special applications of the broad field of transient fluid-flow theory. All solutions of transient fluid-flow problems contain a parameter called the total system isothermal compressibility. This property of fluids and porous rock is a measure of the change in volume of the fluid content of porous rock with a change in pressure, and it may vary considerably with pressure. Evaluation of total system isothermal compressibility is not difficult, but it is tedious and time-consuming. Often compressibilities are estimated roughly, or transient flow methods are neglected completely. The benefits of using accurate system compressibility in properly-executed build-up or drawdown analyses are: 1. Better planning of pressure build-ups may be achieved to avoid unnecessary loss of revenue due to excessively long shut-in periods, or to shut-in periods too short to yield useable data. 2. Better and more reliable estimates of static formation pressures for reserves estimates and rate performance estimates. 3. Reliable information for evaluation of well completion effectiveness, and planning and interpretation of well stimulation efforts. The purpose of this paper is to clarify the nature of the total system isothermal compressibility, and to present useful methods for estimation of compressibility, particularly for systems containing a gas phase. DEVELOPMENT Numerous publications have presented solutions to transient single-phase flow of slightly compressible fluids, stressing pressure build-up applications. In transient flow, a compressibility* term arises to permit volume content of fluids in porous rock to change as pressure changes. The basic nature of the compressibility term is usually taken for granted. Problems arise in practical applications of transient fluid theory because most published works consider only one flowing fluid—in an ideal porous system containing only one fluid. In 1956, Perrine2 presented an intuitive extension of single-phase flow pressure build-up methods to multiphase flow conditions. Later, Martin- established conditions under which Perrine's multiphase build-up method had a theoretical foundation. Perrine has shown that improper use of single-phase build-up analysis in certain multiphase flow situations can lead to gross errors in estimated static formation pressure, permeability and well condition. It is likely that, much pressure build-up data for oil wells should be analyzed on the basis of multiphase flow. For both single-phase and multiphase build-up analysis, the isothermal compressibility term in dimensionless time groups often should be interpreted as the total system compressibility. All real reservoirs contain one or more compressible fluid phases. In addition, rock compressibility can contribute in an important way to the total system compressibility. The proper total system compressibility expression may contain terms for compressibility of oil, gas, water, reservoir rock and terms for the change of solubility of gas in liquid phases.

Jan 1, 1965

THE 125th meeting of the Institute was held in New York, Feb. 20-23, 1922, inclusive, and was the most successful annual meeting of the Institute ever held; there was a larger registration, there were more sessions of importance, and a greater number of sessions, than in any previous year. The total registration was 1331, comprising 351 New York members, 393 visiting members and 587 guests. At the annual business meeting of the Institute, held on Tuesday, Feb. 21, with President Ludlow presiding, there was a much larger attendance than usual. The report of the tellers was read and the following officers were declared elected: Arthur S. Dwight, Director and President-District 0 J. V. W. Reynders, Director and Vice-president-District 0 A. R. Ledoux, Director and Vice-president-District 0 Charles F. Rand. Director-District 0 George D. Barron, Director-District 0 William H. Bassett, Director-District 1 Thomas B. Stearns, Director-District 8 William Kelly, Director-District 5

Jan 3, 1922