Search Documents

By M. W. Dumais, E. P. Abrahamson

In a paper by Abrahamson and Alexander concerning a series of correlations between electronic structure and property changes, it was hypothesized that each solute atom in a dilute solution had a characteristic volume of solvent atoms over which some form of electronic interaction occurred. From this description it is possible to picture the solute atoms as occurring in an ordered array for the most efficient arrangement. A recent review article2 has shown that some form of anomaly exists for a whole series of properties when dilute additions of tungsten are made to iron, of. Fig. 1. Any mechanism to fit one property must also be amenable to mechanisms for the other properties. The possibility of some structural change in this region appears to offer the best hope. The system chosen for investigation was the iron tungsten system. Zone-refined iron with zone-leveled tungsten additions were supplied by Materials Research Corp. as 3/8-in.-diam bars. Transmission electron microscopy was used to study the structure. One-quarter inch specimens of each alloy were cold-rolled to 10-mil sheets, cleaned, punched to electron-microscope specimen-holder size, and annealed in vacuum for 2 hr at 800°C and 2 hr at 700°C followed by a furnace cool. The specimens were attached to a platinum wire and the specimen edge and wire were painted prior to thinning in a solution of 10 pct perchloric acid in glacial acetic acid. It was believed that if ordering were present due to electronic interactions the polishing procedure chosen would provide a simultaneous combination of chemical attack and electropolishing to exhibit the ordered structure. The chemical attack would be expected to penetrate those areas equidistant from the tungsten atoms, while the electropolishing would serve to "plane off" the volumes where the chemical attack had taken place. If one of the ordered tungsten planes were parallel to the specimen face at the edge of the thinned hole, a plate or micalike structure would be expected. A typical result of this polishing is shown in Fig. 2. Here a series of plates can be seen lying one upon the other. In several other specimens the plates parallel to the electron beam have been observed, behaving like slices of bread in a loaf. These edge views coupled with moire patterns indicate that the minimum plate thickness is 37 to 42A. This is equivalent to a concentration of 455 at. ppm of W if a simple cubic superlat-tice exists, or one tungsten atom every twelve iron atoms on the ordered plane. It was further noted that the base iron exhibited no signs of platelike structure. As the concentrations increased above 100 at. ppm W the amount of plate material increased. Among the specimens investigated was that shown

Jan 1, 1967

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964

By James L. Coburn

Leaching is defined as a form of extraction in which a valuable constituent is removed from a solid body by mass transfer to a solution which, for the purpose of this discussion, is considered to be an aqueous medium. Historically, leaching has been applied to the recovery and purification of many elements. This paper, however, is directed toward the recovery of copper, uranium, vanadium, and precious metals included in the following systems: 1. The leaching of copper minerals, sulfides and oxides, by acid or by ammoniacal leach solutions with or without an oxidant. 2. The leaching of gold and silver, either native metals or as minerals by an oxygen-containing alkaline cyanide solution. 3. The solubilization of certain uranium and vanadium minerals by oxygen or oxidant-bearing lixiviants. Many other systems of this general type exist, but from a production standpoint, these three systems account for most of the major values recovered by leaching.

Jan 1, 1975

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

By P. Kluge

Mining engineers frequently encounter complex design problems for which the critical components of the design are difficult to quantify or compare. Teams of people typically work on these designs and human perceptions and judgments play a strong role. To assist with this process, the analytical hierarchical process (AHP) as a decisionmaking tool is described in this paper. Although the technique is used in many other disciplines, it is currently not widely used in mining engineering in South Africa. To use the AHP process, the problem should be treated as a hierarchy that defines the goal, the alternatives to reach it, and the criteria for evaluation of these alternatives. Pair wise comparisons are conducted on the criteria of the hierarchy to establish priorities. The value of the technique is that it is simple to test for consistency amongst the pair wise comparisons to ensure that the answer obtained is better than that provided by a random selection. To illustrate the technique, the use of a backfill support system in a platinum mining project was investigated. Ten design parameters, which will be impacted by the use of backfill, were identified and weighted according to their relative importance. The result of the AHP evaluation was that the use of a backfill support system should be preferred to a conventional support system at the mine.

Jan 1, 2011

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

By Baohua Li, Yanhui Liu, Shengping Li, Xuewei Lv, Yun Chen

There are almost ten billion tons of vanadium-bearing titanomagnetite in Panzhihua-Xichang area. However, iron ores in Hongge, which has the most abundant reserves in the four mine areas in Panzhihua, have not been utilized sufficiently so far. The reason behind this is the relatively high Cr2O3 in the ores (0.49 %~0.82 %), that due to its high melting temperature will negatively influence the blast furnace reduction and slagging process. Therefore, in the blast furnace process, Cr is hope to be reduced into molten iron, which can reduce slag viscosity problems. Slag iron reduction experiments were conducted to quantify the Cr reduction. Experimental results shows that with the increase of TiO2, the content of Cr in the hot metal is decreased when balanced. And during the initial stage of the reduction reaction, the reaction kinetic model is a first-order reaction.

Jan 1, 2016

By W.C Ellis, Earle E. Schumacher

Nonferrous alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,' nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By Earle E. Schumacher, W. C. Ellis

Nonferrous alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,' nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

The revival of the mining industry at Captain's Flat after a long period of years of inactivity has attracted attention to the importance of the ore-deposits of that field as potential sources of supply of lead and zinc. Mindful of the necessity for taking stock of the State's mineral resources, the Department of Mines of New South Wales as part of its programme of geological investigation, carried out a survey of the oredeposits and associated country rocks during 1938 and 1940.Surface geology was mapped in detail and all available exposures were examined and logged. Unfortunately, and this condition militates against the formulation of conclusions because of insufficiem.t data, some of the older workings, notably in Keating's Section, were inaccessible and the logging of levels and stopes is by no means as complete as could be desired. However, with the progress of development and exploration, further information of geological value will come to hand for incorporation in supplementary reports. It may be expected that, under such circumstances, modification of certain statements herein expressed may be necessary but it is not anticipated that any vital alteration will be occasioned.Within the State of, New South Wales, Captain's Flat ranks second to Broken Hill as a pqtem.tial producer of lead and zinc. In addition, large quantities of iron pyrites are available for the manufacture of sulphuric acid which finds application in the superphosphate industry.The mines are now controlled by an operating company known as Lake George Mines, Ltd., incorporated in New South Wales, the parent organisation being the Lake George Mining Gorporation Ltd., registered in London.Over £600,000 has been spent by the Company in exploration, mine development, surface plant, housing and water 'conservation, while the State' Government constructed a branch railway from Bungendore at a cost of £200,000. The various activities consequent upon these development and construction programmes and the prospect of employment in the industry has led to a rapid increase in the population of the township.The State, generally, has benefited to the extent of a substantial contribution to the relief of the unemployment problem, and it is hoped that reasonable permanency will be assured to some hundreds of workers for many years.

Jan 1, 1941

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch' have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

By Antonio Peralta

Mining activity in Mexico began in the 16th century when the Spanish realized the mining potential of the new territory. Since that time, mining has evolved into a strong and vital industry for the country. Good professionals in the mining-related fields are fundamental to the growth and improvement of this industry. Since the end of the 18th century, formal education in mining has been available at the University of Guanajuato, in Guanajuato, Mexico. This school created one of the first schools of mines on the North American continent in 1828. In recent times, some other programs have been created at other universities. Universities offering mining related programs Listed here are the seven universities in Mexico that offer mining related degrees. They are the University of Guanajuato, UNAM, the University of Zacatecas, the University of Chihuahua, the University of Sonora, the University of Coahuila and the University of San Luis Potosi. The University of Guanajuato is the only Mexican university that offers graduate studies at the master's level. No PhD programs in mining engineering are offered at any Mexican university. Programs at each university are of different duration. They are: • University of Guanajuato-Five-and-a-half years, divided into five years of classroom instruction and six months in the working place. • University of Zacatecas - Five years of classroom instruction.

Jan 1, 1994

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019

By Y. P. Chugh

This is the final report of a study done by IIT Research Institute for the Bureau of Mines to identify the problem areas and technological inadequacies in noncoal (metal, nonmetal, stone, and sand and gravel) mining and processing systems that are the primary causes of death, injury and occupational disease, and to make recommendations to improve safety and health in these operations. The findings and recommendations presented in the report are based on: (1) analyses of MESA injury and employment data for the period 1961-70, MESA fatality reports for underground noncoal mines (1968-72) and lost time accident data for 1970-72 obtained from mining and processing operation: (2) visits to a variety of noncoa1 mines and mills throughout the country to observe the operations and to study the safety organization and practices used in the industry and (3) interviews with industry and government representatives knowledgeable in the field of noncoa1 mining and processing safety and health. The report provides a comprehensive overview of safety and health problems.

Jan 1, 1974

By Walter Barnum

AS a member of the Institute and as the president of the National Coal Association, I come before you today in a dual role. As an Institute mem-ber I welcome the opportunity to make complimentary reference to the growing support which bituminous coal operators are giving to programs looking to the advancement of the engineering profession, and to suggest plans whereby these programs may be enlarged to mutual advantage. As a representative of the bitu-minous industry, it gives me special pleasure to express the appreciation of the industry for the services ren-dered to it by members of your profession. Needless to say, there is a close relationship between the engineer and the coal operator. With increasing frequency and in the interests of the industry, the engineer is becoming more of a factor in the business of producing coal. I need look no further for an out-standing example of this encouraging trend than to Samuel A. Taylor, who not only is a bituminous coal producer but also has risen to such eminence in the engineering profession as to have been chosen the head of this great body of technical men, the American Institute of Mining and Metallurgical Engineers. There are many coal operators whom I might mention as having achieved distinction in the engineering world, such as Howard. N. Eavenson, chairman of the .Coal and Coke Committee. And I would be guilty of a serious .oversight if I failed to make reference to Eckley B. Coxe, one of the founders of the Institute in 1871, a prominent anthracite operator and credited with several important inventions. While it is true that a. considerable number of execu-tives of coal-producing companies in this country came up through the engineering ranks. the proportion of mine executives in England, France, and Germany who are graduate engineers is much larger than it is in the United States. In France all members of the staff are engineers and such is the case in Germany up to the owner of the mine. In Germany the owner is not so frequently an engineer as is the rule in France.

Jan 3, 1927

By K. Huessener

Discussion of the paper of K. HUESSENER, presented at the New York. meeting, February, .1916, and printed in Bulletin No. -110, February, 1916, pp. 443 to 474. KARL NIBECKER, Youngstown, O.-It has been contended that the method of measuring the operation of a blast-furnace boiler plant by means of the amount of steam generated per pound of coke used in the blast furnace is not of any value and even that it is quite misleading. It has been found, in the plant with which I am connected, that, in general, a blast furnace will operate during a month so close to average. conditions that the average monthly measure of the plant efficiency is indicated by the number of pounds of steam made per pound of coke put into the furnace, neglecting the amount of iron made and the amount of gas used for heating the stoves. For some time, it has been our custom to keep a record of this figure and use it as a general indicator of the operating practice. In comparing this figure from two different plants we have found some difficulty, due to differing conditions. It is conceivable but not altogether probable that a slight difference in burden, kind of ore or coke, would account for this difference. The method of using the gas, whether washed or unwashed, and the plant arrangement, may affect this number. For several plants on which we have worked up this number, we have found that most of the ordinary running irregularities are eliminated during a run of a month or more and that the number is, therefore, satisfactory. In connection with a plot of the number of pounds of steam generated per pound of coke, we are also plotting the production of the furnaces and the pounds of coke used per ton of production. With these three curves plotted on the same sheet, we believe that the operating man has sufficient information to judge of the efficiency of his plant' for any month.

Jan 5, 1916

By Irving M. Symonds

COMPA[N]IA Minera de Penoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Pe[n]oles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torréon, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005