Search Documents

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By Harry V. Warren

THE Dolly Varden Mine is situated in the Kitsault River valley, eighteen miles from the head of Alice arm, in the Nass River mining division of British Columbia. During the years 1919-21 it was operated by the Taylor Engineering Company, Limited, and produced 1,300,000 oz. silver from about 36,000 tons of ore. The ore was transported by narrow-gauge railway to Alice arm, and shipped to the smelter at Anyox for treatment. During recent years, a small quantity of high-grade ore has been extracted by leasers and shipped to the smelter at Tacoma, Wash. Unfortunately, the bonanza ores which occurred near the surface did nor persist to depth, and two hundred feet below the exposures only rare and unimportant patches of ridi ore have been found. Two opinions exist as to the origin of this rich silver ore. One, advanced by V. Delmage (1, 2), is that the ores are hypogene, and the other, by G. Hanson(3, 4, S), is that the ores are the result of supergene enrichment. It is true that Dolmage first advanced his view that the ores are primary because they appeared to be analagous to Premier ore, which he had studied in detail and which he considered to be primary. The present authors have had access to excellent suites of material from both mines and consider the comparison well taken, the only essential mineralogical difference being the presence at the Premier mine, in addition to the silver minerals, of gold and electrum. Although the arguments put forward by Delmage have, in the opinion of the authors, never been refuted, nevertheless R. P. D. Graham(6), in a reference to the mine published in 1924, describes the ore as of supergene origin, and since then nobody appears to have challenged this statement. Indeed, in 1935, Hanson re-affirmed his earlier conclusion(5).

Jan 1, 1942

By A. F. Daily

Free World consumption of diamonds of all types closely follows the fluctuations of the business cycles in the large industrialized countries, particularly the U.S. Sustained purchasing by this country for stockpiling purposes has been a major factor in Free World demand for crushing bort and industrial diamonds, and it has been for this reason that investments in larger plants have been made by all major diamond mining companies during the past few years. For the purposes of this study, the diamonds produced in the Congo and elsewhere in the Free World are divided into three types:

Jan 5, 1961

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By H. V. W. Donohoo

Exploration in 1955 was marked by a trend toward large-scale programs using a number of geophysical techniques. These programs were initiated both to locate new mineral districts and to bring individual prospects into production. All 14 companies replying to the author's questionnaire include geophysics in the general exploration routine whenever it is applicable, and five companies carry on extensive geophysical programs. Nearly all report that company personnel perform the surveys. In addition to these firms there are the many smaller operators who contract much of their geophysical work. There are indications that the volume of such contracting is sizable.

Feb 1, 1956

By W. C. Ellis

For the purpose of developing combinations of higher strength and conductivity than are obtainable by heat treatment alone in the age-hardening copper alloys, an investigation has been made of the effects of combinations of heat treatment and strain hardening on the properties in question. The investigation was limited to a study of the alloys containing nickel and silicon; nickel, silicon and cadmium; and cobalt and silicon. The experiments made in the course of the study are described in this paper in three groups: 1. The effect of hard drawing subsequent to heat treatment on the mechanical and electrical properties of the alloys. 2. The effect of low-temperature aging on the properties of heat-treated and hard-drawn alloys. 3. The effect of strain on the rate of aging of quenched nickel-silicon-copper alloys.

Jan 1, 1931

By George D. Roberts

INTRODUCTION CIVIL engineers are primarily interested in maximum core recovery. This is even more important in foundation work than in mining investigations where sludge samples are of some value. The soft materials, such as clay, gouge, or partially decomposed seams that are most readily ground up or washed away, are the materials that usually have the greatest influence on foundation and leakage conditions. Undisturbed samples of such materials should be obtained for detailed geological examination and laboratory tests. Therefore the attainable goal of sampling in connection with foundation investigations is the recovery of 99.9 pct of undisturbed core. FACTORS CAUSING CORE LOSSES The principal factors contributing to core losses are: (I) coring badly fractured or very soft material; (2) use of improperly designed coring equipment, including the use of bits of too small a diameter; (3) lack of the proper training and attitude on the part of the drillers and pertinent technical information on the part of the supervising personnel. Little can be done about the character of the material being cored but the other two factors contributing to unsatisfactory performance can be corrected. Although the title of this paper is the improvement and standardization of core barrels, it is believed that the drillers' shortcomings and the lack of pertinent technical literature are more detrimental to good core recovery than either of the other factors. USES FOR LARGE DIAMETER CORE BARRELS It is well known that the use of larger diameter bits and core barrels generally produce better cores, particularly when sampling soft or broken material. The use of larger and larger bit diameters and the insistence on better core recovery is well demonstrated by the change in practices of the various districts of the Corps of Engineers. Today NX core is the smallest diameter commonly permitted for investigational work and the more active districts are using coring bits up to 6 in. in diameter, as well as 36 and 40-in. calyx rigs. The latter size has proved to be just as economical because it provides more room for core removal and cleanup operations. The use of large diameter cores to replace the driving and jacking methods of obtaining soil samples is also increasing. The 5 7/8-in. Denison sampler, developed by H. L. Johnson to obtain samples from soft formations, is one example. The principal uses for bits larger than NX are: sampling soils and semi-consolidated rock; sampling decomposed rock or rock with soft seams; sampling concrete; obtaining samples for laboratory tests; drilling drainage holes, and other miscellaneous work. CORE DRILLING PRACTICES OF SEVERAL ENGINEER DISTRICTS Little Rock District The writer was employed in the Little Rock District from 1938 until 1942. Prior

Jan 1, 1947

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325. As part of this giant effort, the smelter planning team and supervisory staff considered that new, well organized, highly flexible, readily available maintenance information was essential to assist the maintenance personnel in the performance of their duties.

Jan 1, 1979

By Gauti Asbjörnsson

Material handling is an essential part of the aggregate and mining industries. Mixing and blending of granular material can affect the grading and particle size distribution of the material leaving the system. Segregation and variability can cause problems in the downstream process while insufficient capacity will disturb upstream processes. Process plants utilize surge bins for handling recycle streams of material and act as a buffer for the process. The flow through the surge bin is usually controlled by a simple PID controller or PID controller in combinations with a plant-wide controller. Even though the surge bins play an important role of smoothening out the plant and creating a steady operating condition they are seldom included in plant simulations. This can lead to a number of problems in the form of decreased plant capacity, plant lockdown, and even operation units malfunctioning. The main objective of this study is to investigate the dynamic behavior in surge bins and develop a model more suitable for representing this behavior, which can occur during operation, for dynamic simulations. The proposed model adopts vertical layers which allow for flows between segments depending on the level of neighboring segments. This enables both the representing of segregation within the system and gives an indication on the effects from different inlet- and outlet placements. The proposed model was developed in MATLAB/Simulink and validated against an actual bin with the total capacity of 660 m3 in platinum ore application. With the new bin model significantly higher fidelity and more accurate dynamic, simulation results were achieved. Keywords: dynamic simulation, modeling, segregation, material handling, MATLAB/Simulink

Sep 1, 2012

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

By Robin Adams

After nearly five years of economic hardship, the world copper industry is, in our opinion, about to enter a period of considerable strength. This opinion is based on three main propositions, namely: 1) there are a number of reasons, both general-economic and industry-specific why copper demand is likely to perform significantly, more strongly in the 1980's than in the 1970's; 2) the virtual cessation of investment in new facilities, especially at the mine level, over the past years makes it physically impossible for capacity to expand as fast as demand in the mid-1980's; and 3) there is much less "excess" inventory available than most analysts believe. If we are correct in these assumptions, then the implication is that copper prices will climb up to, and possibly beyond, the cost-justified price level. Combined with general inflation, this suggests a price in excess of $2/pound by 1985 or roughly treble the 1978 average.

Jan 1, 1979

By D. Van Dooren

The final goal of the research project is to develop a 3D FEM model that is able to predict the kinetics and micro-structural evolution during the bainitic transformation. The input parameters consist of thermodynamic and atomic mobility data obtained from the ThermoCalc and mCTRA databases combined with structural mechanics data extracted from the stress-strain curves of the fcc and bee phases. In this paper the general principles of the model are outlined and some interesting preliminary results are shown and commented. The full implementation of the model has presently not been achieved yet. In the model the bainitic transformation is considered as a sequence of martensitic (re)nucleation and growth of a ferritic subunit followed by the carbon rejection into the surrounding austenite. The (re)nucleation of the subunits will be described through a non-classical martensitic nucleation criterion. Once a nucleus has been activated at a specific location in the material, a full-sized subunit is instantaneously formed through a displacive mechanism. The stress state in the system that arises due to the transformation strain can be calculated by a 3D FEM programming code. Immediately after the formation of the subunit, another 3D FEM programming code calculates the carbon diffusion from the supersaturated ferrite into the surrounding austenite. The resulting stress state and carbon profiles will be used to determine where and when a new subunit will nucleate based on a renucleation criterion. Keywords: Bainitic Transformation, Modeling, Eshelby, Carbon Diffusion

Jan 1, 2003

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By F. Leclerc, V. Rebeyrolle, M. Revil-Baudard, A. Jardy, M. Založnik, H. Combeau

"Since the quality of Vacuum Arc Remelted ingots is linked to their chemical homogeneity and metallurgical structure, a modeling study of the solidification during VAR has been undertaken. It is based on the solution of the coupled transient heat, momentum and solute transport equations during the remelting of a cylindrical ingot. Solidification mechanisms implemented in the model include a full coupling between energy and solute transport in the mushy zone, and accounting for nucleation and finite diffusion of solutes at the microscopic scale, in both solid and liquid phases. This modeling can be applied to actual multi-component alloys. In this paper, the macrosegregation in Zircaloy 4 ingots is investigated. To validate the model, one single melt of a homogeneous electrode has been specifically performed. The comparison between the predicted macrosegregation and the experimental results shows the importance of accounting for solutal convection to forecast properly the macrosegregation in remelted ingots.IntroductionVacuum Arc Remelting of zirconium alloy ingots is a key step in the manufacturing process of fuel assembly components in nuclear reactors. The control of the chemical homogeneity is indeed fundamental to ensure the quality and the in-reactor performance of the final products. Despite the use of electromagnetic stirring to homogenize the liquid melt composition, chemical heterogeneities develop in the mushy zone during the solidification stage. One of the main challenges for zirconium producers, as well as titanium producers, is to master the VAR process in order to control the macrosegregation in remelted ingots. Macrosegregation results from the association of microsegregation and transport phenomena. The latter are primarily due to the flow in the liquid and mushy parts. It is now well established [1-4] that the hydrodynamics of the melt pool in a VAR ingot depends on the combined action of the followings: thermal and solutal buoyancy, self-induced electromagnetic force and the periodic centrifugal force caused by the angular movement generated by the stirring. However, for zirconium alloy ingots, the effects of thermal and solutal buoyancy forces on macrosegregation through their influence on the flow in the mushy zone have not been clearly identified."

Jan 1, 2012

By Y. Q. Lu

Efficient flotation of fine phosphate minerals from a deslimed waste phosphate stream (-74 microns) has been achieved by both bench-scale flotation and by flotation with a 2-inch air-sparged hydrocyclone (ASH) unit. A sample was collected from the waste phosphate slime stream at the SF Phosphate Limited Operations near Vernal, Utah, for flotation experiments at University of Utah laboratories. The collector used was a mixture of fatty acid, petroleum sulfonate and kerosene. Bench-scale flotation test results show that the minus 15-micron particles have a significant adverse effect on phosphate flotation. When the minus 15-micron material was removed by a classifying hydrocyclone, improved flotation recovery and concentrate grade were realized. A bench-scale flotation recovery of 86 % with a concentrate grade of 16% P2O5 was obtained from classified waste slime (74 x 15 microns) feed material containing 11.3% P2O5 In contrast, a 90% P2O5 recovery was achieved with a concentrate grade of 16-18% P2O5 by single-stage ASH flotation. With a second stage of ASH flotation, a concentrate containing 23% P2O5 was realized at an overall recovery of 75%. These results indicate that the industrial application of ASH flotation technology for phosphate recovery from waste slimes is promising.

Jan 1, 1995

By K. H. B. Wenzl

"Since the autumn of 1973, the world's attention was captured by the startling revelation that conventional energy supplies were not inexhaustible but were in fact quickly dwindling with future shortages imminent until lagging exploration and technology yielded additional energy sources to catch up with the spiralling increase in demand. This situation was precipitated by the Arab Oil Embargo and the resulting soaring cost of world crude oil.During the past few years there has been tremendous activity in the energy field which has had a direct impact on the Inca Metals Company Ontario Division operations. The company's reaction has been to establish an energy management program which will be described later in the paper. First, a brief description of the Inca Metals Company and the primary energy resources which are utilized will assist in putting the program into perspective.The Inca Metals Company, a unit of Inca Limited, is responsible for the production and sale of primary metals products worldwide. The company's operations in the Sudbury District include mines, ore concentrating plants, a Smelter, Nickel and Copper Refineries and an Iron Ore Recovery Plant. The Ontario Division also has a mine and concentrating plant in Shebandowan near Thunder Bay, and a metals refinery at Port Colborne. Inca is the largest producer of nickel in the non-communist world and is also a major producer of copper and platnium group metals."

Jan 1, 1978

This paper discusses the impacts that advances in metallurgy and process engineering have on minerals project execution. Ausenco's business is focused on integrating minerals processing technology and the delivery of cost effective processing plants that exceed client performance expectations. The metallurgical development is a small but critical part of this process. Metallurgical development and innovation outcomes need to be transformed into an engineered solution and that solution converted into an operating plant in a cost conscious and competitive environment. Including new or innovative processes in a project flow sheet increases a project's technical and commercial risk. However, it also gives the project, and/or the engineering company, a potential advantage over projects using mainline practices. Managing the balance between risk and opportunity has been a cornerstone of Ausenco's success in recent years. Some advances in "technology" that are discussed in the paper include: larger capacity equipment new flow sheet concepts simplification of process interfaces, and more effective project strategies The common theme is that having a new idea can be the easy bit, putting it into operation effectively involves numerous people, many interfaces and strong project management.

Sep 13, 2010

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019