Search Documents

By L. Yan, N. Damiano, J. Bickson, E. Bauer, D. Yantek, B. Whisner, M. Reyes, J. Srednicki

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35°C (95°F) [1]. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by >5.6°C (10°F) in mines with elevated mine strata and air temperatures. In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35°C (95°F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy. INTRODUCTION The apparent temperature inside an occupied RA could be significantly affected by the surrounding environment’s thermal conditions, such as mine air temperature and mine strata temperature. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and air velocity. It is used to assess the perception of indoor temperatures. Depending on factors such as geographic location and season, mine air temperature, relative humidity, and mine strata, temperatures can vary significantly [2]. RAs located in cold mines may pass the 96-hour 35°C (95°F) AT limit test that poses a challenge for RAs located in hot mines. One solution in these cases is that the occupancy of the RA could be derated (i.e., the RA occupancy could be reduced) to ensure the AT limit is not reached. However, this would require mines to purchase additional RAs to accommodate all personnel in the mine. For mines with high temperatures (above 26.7°C or 80°F), the occupancy might have to be reduced so much that the necessary number of additional RAs would be impractical. In these cases, RA cooling systems could provide a solution.

Jan 1, 2019

By James N. Bayne

An examination and analysis of Landsat digital data in the monitoring of surface mines in selected counties of South Carolina.

Jan 1, 1979

By P. Minkkinen, R. C. A. Minnitt

Particle size distribution analysis is important to many industries for assessing product quality, process efficiency, and compliance with contractual standards, while ensuring sample accuracy, and representativeness. Inaccurate particle size distribution results, arising from fines due to excessive handling can lead to penalties and buyer-seller disputes. A non-representative particle size distribution means samples will not accurately represent the chemical components either. Sampling blasthole cuttings poses challenges due to large material volumes, segregation, and uneven settling of particles in dense gold bearing ores. Commonly used sampling methods, such as spear or sectoral sampling, may lack representativeness. Particle size distribution analysis is crucial for evaluating sampling methods by comparing test sample representativeness against a reference standard derived from multiple particle size distribution analyses. Acceptable samples must fall within the 97.5% confidence intervals of the standard; deviations analyses lying outside these boundaries indicate a strong likelihood of segregation errors. A case study demonstrates this approach by using a 6.005 kg benchmark sample to assess two additional samples (1 kg and 5 kg), highlighting particle size distribution’s role in detecting sampling errors and refining protocols. An example of three test samples collected from reverse circulation drill cuttings compared to a standard reference sample is presented to illustrate a quality assurance/quality control procedure for reverse circulation drilling.

Oct 2, 2025

By Edmund C. Bovey

"AS I begin my remarks this morning, please let me say how honoured and gratified I was to receive your invitation to address you here during your deliberations in historic Quebec City. The high esteem in which your Institute is held is reflected in the respect and deference accorded to it by industry across Canada. I feel privileged to be here with you today.I would like to discuss with you some applications of natural gas in the mining industry and suggest to you, in closing, some possible avenues of future development.Natural gas first became avail-able for industrial purposes in Northern Ontario in late 1958. Acceptance of natural gas, as a source of energy by the industry of that area, has been both widespread and gratifying. The mining industry of Northern Ontario has in-creased its annual use of natural gas by approximately 35 per cent each year since 1958. We believe that this trend will continue, al-though we will probably have to accept a more modest 10 per cent annual gain as the market approaches saturation. I would like to explain how we were able to do this and where all this gas is used. Our first sales were largely a matter of price-and the savings we offered were substantial."

Jan 1, 1966

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of' the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By J. Kenneth Wittle

The DC Graphite Melter has been shown to be capable of processing radioactive waste materials. The process is characterized by its high temperature capability and operation in a closed system. From an environmental perspective, the control of emissions coupled with destruction for hazardous organic materials is mandatory. These same characteristics may be applicable to the minerals processing industry. Under normal operation, the system reaches temperatures for nominal operation of 1600°C, with an arc temperature in the order of 5000°C. The system temperature is determined by the melt temperature of the material being processed. In testing of a 750 lb/hour unit, temperatures of 2200°C were reached. Current focus is on finding waste treatment and metals recovery opportunities in the metals processing industry for his innovative technology.

Jan 1, 1999

By Arthur A. Cole

Although the metal silver has been known and prized from very ancient times, it is in the New World that the greatest silver camps have been found. This is shown in the following comparison: [] For the last few years, the World's annual production of silver has averaged about 240 million ounces troy. Of this total, the North American Continent contributes approximately three quarters, Mexico leading with 38 per cent, followed by the United States with 27 per cent, and Canada with nearly 9 per cent.[] Of the largest silver producers in Canada, the Sullivan takes first place. Although primarily famous as a lead and zinc mine, it produced, in 1926, more than 4.5 million ounces of silver. The Premier mine, in northern British Columbia, produced more than 3 million ounces. In Ontario, the largest producers in 1926 were the Nipissing mine, .with 1.9 million ounces, and the Keeley mine, with 1. 7 million ounces. The Mining Corporation produced 1.1 million ounces from mines in the Cobalt district proper, and an equal amount in South Lorrain; while from the Castle-Trethewey mine, in Gowganda, there was an output of slightly less than one million ounces.

Jan 1, 1927

By Norman L. Kotraba

In Electric Arc Furnace (EAF) steelmaking, dust emissions are collected in a baghouse to prevent their escape to the Environment. This fine dust, predominantly iron oxide, also contains oxides of various other metals introduced into the EAF from the scrap charge. For example, mixed or galvanized scrap brings with it zinc, lead, and small quantities of cadmium which preferentially accumulate in the collected off-gas dust. Stainless steel scrap brings chromium into the charge, some of which also makes its way into the baghouse dust as hexavalent chromium-containing oxides. Because many of the contained heavy metal oxides are water-leachable, the U. S. Environmental Protection Agency has listed EAF dust as a hazardous waste which, as of August 8, 1988, cannot be 1andfi11ed without first being treated. Moreover, beginning August 8, 1991, all dusts with zinc concentrations of 15% or greater will be required to undergo high temperature thermal treatment to remove the heavy metals prior to any further disposal. This deadline represents several EPA-granted time extensions to the original requirements; extensions which were granted to allow for further development of process technologies.

Jan 1, 1991

By AIME

IN the parlance of Hollywood, it was a super-colossal meeting. In the more restrained language of engineers, the Institute's 75th Anniversary Celebration attracted the largest crowd ever; was the longest Annual Meeting ever held, occupying a full week; had more important papers, more important people, more of an international flavor, and more glamour than ever before. And in the minds of those who came to the big city from the wide open spaces, one other record should be mentioned: for those not on an expense account, it was the most expensive affair ever staged by the Institute! To state the attendance down to the last digit for a meeting such as this is impossible. The total names registered on cards, plus those who attended the Annual Banquet but were not otherwise registered, came to 3149. But a few were registered twice, and probably a still larger few did not register at all, but just dropped in for a session or two in which they were interested. It would appear that 3200 would be about as close an estimate of attendance as could be made, and that is some 300 more than came to the biggest Annual Meeting of the past-in 1944. A considerable number of members brought their wives, but most were delegates at large.

Jan 1, 1947

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996

By Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

The possibility to develop an efficient recovery and reuse of concrete materials from Demolition Waste (DW) represents one of the main targets applied to end-of-life constructions dismantling/recycling. The need to recycle end-of life concrete materials is strongly increasing in these last years for several reasons: i) the decrease of steady supplies of good quality natural aggregates, ii) the need to secure ample supplies of concrete aggregates to the construction industry and, finally, iii) the environmental constraints limiting the DW wastes disposal. The fulfilment of these goals produces several benefits, that is: i) a reduction of new resources consumption, ii) a strong reduction of the costs linked to transport and energy production, iii) the possibility to utilize materials, otherwise lost (e.g. land filled), iv) land preservation and, finally, v) the reduction of the environmental impact of new exploitation activities. A lot of efforts have been addressed to develop, set-up and apply innovative technologies to maximize DW conversion into useful secondary raw materials. The possibility to utilize efficient, reliable and low cost analytical tools to perform detection/control actions: i) to assess concrete characteristics, before demolition, and ii) to detect the presence of contaminants in coarse aggregates (e.g. bricks, gypsum, steel, glass, plastics, wood, etc.) represent the key issues to fulfil in order to develop innovative process/control actions/procedures inside the DW sector. In this paper a new technology, based on HyperSpectral Imaging (HSI) sensors is investigated to develop suitable and low cost strategies finalised to define and implement innovative smart detection engines for sorting and/or DW flow stream quality control, addressed to perform recovered materials and/or products certification. The proposed sensing architecture is fast, accurate, affordable and it can strongly contribute to bring down the economic threshold above which recycling is cost efficient.

Jan 1, 2014

By G J. A Dewar

The Australian Corporations Law generally requires Independent Expert Reports to be presented in support of capital raising or in defence of mergers and takeovers. The introduction of the VALMIN Code in 1995 (and its recent revision issued as the VALMIN Code, 1998) made Assessment and Valuation Reports in these circumstances much more comprehensible than before because of its key requirements for transparency and materiality. By forcing the Independent Valuer to provide an explanation of the reasoning behind the estimation of a particular resource asset, VALMIN allows the reader to clearly see any error or illogicality in the valuation methodology used and to seriously question or even reject the resulting value. Even though many elements of resource asset valuation practice are undeniably subjective, there must be some basis of objective rationality to it. Independent resource asset Valuers are the essential link between mineral explorers/miners on the one hand and brokers/analysts/fund managers/investors on the other. The minerals and financial industries both expect them to not use inappropriate or invalid valuation methods and illogical steps within these methods. This paper examines some of the less sensible ways in which some of the main techniques that Valuers commonly use to assess the fair market value of mineral properties have been applied in recent instances. The authors hope to discourage the adoption or perpetration of the æWhat-number-did-you-have-in-mind?' approach. It is MINVALÆs view that as many methods as possible should be used in any resource asset valuation. If any of the resulting estimates are in approximate agreement (particularly if they were derived using the less subjective of the available methods), ie if they cluster, they are probably more persuasive as being the Preferred Value of the asset than outlier values within the Valuation Range.

Jan 1, 1999

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter's Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all 'hot-metal' basis.

Jan 1, 1938

By E. Neumann

With fuel costs unstable but escalating, solid fuels are playing an increasingly larger part in industrial concerns. Coal, petroleum coke and wood are examined from a burner system design viewpoint and from operational experience in kilns, hot gas generators, etc. The burner of today must also handle multi-fuel tasks and allow immediate, painless switching from one fuel to the next as well as the simultaneous burning of two or mope fuels. The paper discusses the principle of burning alternate pulverized fuels as well as the practice both in the United States and around the world.

Jan 1, 1983

By Michael Tenenbaum

A REVIEW of process metallurgy of iron and steel during 1944 in many ways reflects the political and military developments of the year. Early in 1944 the tremendous wartime emergency expansion program was virtually completed and the industry directed its efforts to maintaining maximum production wherever needed. The vigorous production programs inaugurated to support the Normandy invasions did not persist as Allied armies approached Germany. General public apathy which developed with the prospect of an early ending of the European fighting was reflected in a general relaxation in armament programs. Toward the end of the year, as the prospect of a prolonged war became real, the entire program revived considerably and the need for steel became acute. Between January 1940 and October 1944 more than 12,400,000 tons had been added to the nation's steelmaking capacities, and over 12,700,000 tons added to the blast-furnace facilities. The total cost of this enormous program was more than two billion dollars. By July 1, 1944, total steelmaking capacity had exceeded 94,000,000 tons, with blast-furnace capacity rated at 68,400,000. Annual steel production, which was 88,900,000 tons in 1943, increased slightly during the past year and was estimated at 89,500,000. Production of pig iron also increased somewhat from 61,800,000 tons in 1943 to an estimated output of 62,500,000 in 1944. This review deals with a few of the numerous factors involved in maintaining the wartime iron and steel program at the level necessary to accomplish this enormous output.

Jan 1, 1945

By K. C. Sole, G. Robinson, M. S. Moats, W. G. Davenport, S. Sandoval

Global practice in hydrometallurgical production of copper cathode by electrowinning is reviewed, based on individual plant operating data for 2018. Data from 29 plants were collected, representing 38% of world cathode copper production. Similar surveys were carried out in 1997, 1999, 2003, 2007, and 2013. This survey includes analysis of historical and current data. Evolving trends in operating conditions and performance, as well as equipment design and process technology choices, are analysed and differences in operating practices with location are assessed. Examples of recent technology and operational choices to increase productivity, improve copper quality, and decrease electrical energy consumption are discussed. Significant project expansions, particularly in Africa, and the consolidation of numerous small Chinese operations are also presented. INTRODUCTION Global trends and operating practices in copper electrowinning (EW) in 2018 are reviewed and evaluated. Similar world and African surveys were carried out in 1997, 1999, 2001, 2002, 2003, 2007, and 2013 (Robinson, Davenport, & Jenkins, 1997; Jenkins, Davenport, Kennedy, & Robinson, 1999; Davenport, Jenkins, Robinson, & Karcas, 2001; Robinson, Garbutt, & Davenport, 2002; Robinson, Davenport, Jenkins, King, & Rasmussen, 2003; Robinson, Davenport, Moats, Karcas, & Demetrio, 2007; Robinson, Sole, Sandoval, Moats, Siegmund, & Davenport, 2013). Contributing operations included sites from the USA and Mexico (9), Chile and Peru (6), Laos (1), Kazakhstan (1), and Africa (9). Despite fewer contributions compared with past experience, this survey nevertheless represents 2018 copper EW cathode production of 1.76 Mt, or about 38% of world production of 4.64 Mt (International Copper Study Group, 2017). This drop in permission to contribute is attributed to the more competitive nature of the industry and unprecedented production pressures; furthermore, several operations in Australia have shut down, while large operations that are currently commissioning or ramping up to full production in Africa and Asia declined to participate. Of the Chinese operations, which represent an increasingly important proportion of global electrowon cathode copper, particularly in Africa, only Tenke Fungurume (Democratic Republic of Congo; DRC) participated in this survey.

Jan 1, 2019

By E. W. Engelmann

RAPID progress has been made during the past year in the copper mills throughout the country. Particular efforts have been made to increase the fine-grinding efficiency by the installation of larger classifying units operating in closed circuit with ball mills, such as the 78-in. high-weir Akins installation at the Phelps Dodge plant at Ajo, Ariz.; also the Type "FX" Dorr classifiers of Nevada Consolidated at McGill. Nev. and the "FX" Dorr bowl classifier of the Braden Copper Co. in Chile. Some of the copper milling plants in the Southwest, such as Chino in New Mexico and Ray Con. in Arizona, have replaced rolls operating wet in their fine-grinding circuit by rod mills. At Hollinger primary rod mills were formerly used in open circuit followed by pebble mills in closed circuit with classifiers. They now have primary ball mills in closed circuit with large extra heavy classifiers and no secondary mills. This new installation is producing the same grinding on 5000 tons per day with a reduction in cost of nearly 4c. per ton. At the Braden plant, in Chile, short-head Symons crushers have replaced 54-in. rolls, thereby in- creasing crushing capacity with some saving in maintenance cost.

Jan 1, 1939

By Xie Hao

According to its raw materials orthogonal test scheme is designed and a large number of systemic experiments were carried out in order to study the sintering characteristics of three types of fine ores in Kunming Iron&Steel Co.Ltd(KISC). The effects of carbon mixture ratio and basicity on sintering time, agglomeration ratio, physical properties and utilize coefficient were researched via single factor analysis and range analysis. The experimental results show the best mixture ratio of each fine ore. Analysis found that the influence of the carbon mixture ratio is more significant than which of the basicity on the sintering process except agglomeration ratio of foreign ore.

Jan 1, 2009

By L. Deininger

The QSL plant in the existing "Betzelius" Stolberg GmbH lead smelter in StolberglGermany was commissioned in August, 1990. Following some modifications to the process and equipment which had become necessary in line with the implementation of this new techno- logy, conclusive operating results are now available. These will be reported together with a short description of the plant design. In May 1992, raw material feeding to the QSL reactor in the new lead smelter of Korea Zinc Co. in OnsanlKorea was started. As all the experience gained up to that point in time in the Stolberg plant had already been incorporated in this plant prior to start-up, it reached stable, satisfactory operating conditions in a short period of time. After an introductory description of the plant important operating results will be reported. The operating experience gained in the two plants fully confirms the correctness of the in- ventors' creative ideas in the 70s. The QSL process meets all demands made on modern, ecologically compatible and energy-saving lead production technology. The paper ends with suggestions on how the QSL process will be optimized further in the future.

Jan 1, 1994

By G Dunstan

The Ridgeway gold mine has been an enigma of the international underground hard rock community for nearly 20 years. It nearly didn’t eventuate as it was more than 500 m below a farmer’s paddock in Central New South Wales when the exploration team, looking for open pit deposits, got a sniff on its last attempt and then drilled the high-grade discovery hole. It took separate studies to find an economic mining approach. Newcrest, then a mid-tier mining company, took the venture that set it on a path of growth and built what was to become the backbone of the company for the next 15 years.The initial mining method was sublevel caving (SLC) for the upper 300 m of the orebody. The nameplate production rate for the SLC was 4 Mt/a, which was reached in June 2002 shortly after the commissioning of the materials handling system. The ultimate production rate was subsequently lifted to around 6 Mt/a through a series of innovative and efficiency initiatives. In June 2007, approval was granted for the development of a block cave (BC) operation to extract the ore reserve situated immediately below the existing SLC operations, Ridgeway Deeps. The BC was designed at approximately 6 Mt/a to match the concentrator and a systematic improvement process through the entire underground system again saw delivery rates consistently around 10 Mt/a.In line with the production rate increases, Newcrest was also committed to advancing caving knowledge through a number of targeted research and development experiments and new processes. These were primarily related to improving cave ore recovery through systematic draw marker trials, cave propagation through preconditioning techniques with associated monitoring systems. New technologies were also developed to improve the safety and efficiency of the mine through data collection, cave establishment techniques, production dispatching and autonomous loading.CITATION:Dunstan, G, 2016. The truth is stranger than fiction – the story of Ridgeway gold mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 19–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016