Search Documents

By Harrison R. Cooper

INTRODUCTION AND SUMMARY Phosphate matrix beneficiation is the process of providing a mineral product suitable for downstream chemical processing to yield high analysis chemical fertil- zers. Extraneous contaminants, clays and gangue solids, are separated by screening and flotation. Reject materials always carry with them some phosphate mineral values, however. A continuing objective is minimizing phosphate losses discarded with tailings as a principle factor in maintaining beneficiation efficiency. The quest for efficiency, and improved productivity, during beneficiation is hampered by disturbances arising from among the following: o Natural variance of phosphate deposit compositions, o Minimal control over managing ore matrix supply to the plants, o Screening and flotation mechanical upsets and inefficiencies. Production personnel, in recognizing these factors, attempt corrections for changed process conditions. This response usually has limited effect. Efforts of product- ion personnel to correct for upsets of the process may often diminish efficiencies rather than improve them. Lack of prompt data for analysis of process streams is an important contributing cause of inefficient operation. Discussion in this paper examines methods for improved process control in Florida phosphate beneficiation with particular emphasis on use of on-stream analysis to aid gaining productivity. The Florida Institute of Phosphate Research has supported demonstration of on-stream analysis applicable to improved process control. Concurrently, work is proceeding world-wide in the phosphate industry toward practical on-line analysis technology. Table 1 summarizes viable methods for real-time analysis data as result of work by individual companies and research organizations. A recently completed investigation (sponsored by the Florida Institute of Phosphate Research) of beneficiation efficiency was carried out in two Florida beneficiation plants using a newly developed on-stream analyzer for phosphorus (1). BPL measurements were taken at frequent intervals over two to three weeks of routine operation. Grades are expressed in "BPL", with one BPL, or bone phosphate of lime unit, equal to 0.46 P^Y2^YO^Y5^Y. The time series of feed and tailing BPL data were evaluated by statistical procedures. Results show avoidable losses can be five per cent or greater of mineral values in feed. Use of modern process control methods in Florida phosphate mining began several years ago (2, 3). Benefits of stabilizing control used in one of the two plants where data were collected for the investigation, in comparison to manual control in the other, are outlined. Process control technology developments reported from European and South African phosphate mining operations are also noted (4, 5). It is now well accepted that advanced control techniques can increase beneficiation productivity by better management of losses. However, to make advanced control effective, real-time measurements are needed of feed and tailings BPL as well as mass flow rates.

Jan 1, 1993

By Lutz Markworth, Fernando Parra, Wolfram Jaspers

"The worldwide demand of iron ore and the depletion of the high-purity deposits make it necessary to recover ores in increasingly fine size fractions or low Fe content in the feed material. Impurities for Iron ore processing plants are mainly Silica, Al2O3 and Sulfides.There is a copper processing plant in Chile, which has a high content of Fe in its tailings. These tailings will be re-processed to recover the Fe and to produce a pellet feed concentrate. This challenging flotation process was developed by the customer in his own laboratory. Different flotation technologies were tested. The best results were achieved with the PNEUFLOT® (PNEUmatic FLOTation). For a feed capacity of approximately 600 t/h, a flow sheet of two flotation lines with a reverse two-stage Amine-Silica flotation followed by a single stage reverse Xanthate Pyrite flotation was developed.Because of the two impurities the process control is very critical. Not even the reagent dosing has to be flexible for changes in the feed material; also the flotation cell has to be adaptable. Continuous development of the PNEUFLOT® cell with their specific advantages and the elimination of dysfunctions in the PNEUFLOT® cell have led to a growing demand of this type of equipment worldwide for the iron ore industry within the past years.INTRODUCTIONThe worldwide increasing demand of iron ore is mainly caused by China. This has a major impact on all economics worldwide as the metal price indicates. However, not even the iron ore and steel price, but all other commodities prices and the precious metals prices are increasing by a high percentage. Figure 1 shows the iron ore (pellets) price increase for Fe and the import of iron ore by China. Figure 2 shows the imports of iron ore to China."

Jan 1, 2008

By E. P. Polushkin, Henry L. Shuldener

THIS paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. PIPES EXAMINED The pipes were made by different manufacturers and their sizes range from ¾ in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often 100 to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is 100° to 160°F. WATER SUPPLIES The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table I are characterized by relatively low hardness, low alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1944

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, 'pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.' However, the components which are strongest in the recrystallization texture are in this range.'________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,' 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.'~-'~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.' In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2'13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,'~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.' state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By J. A. Bleeck

A discourse on the relationship between industrial minerals and paper production, concentrating on high grade, ultra fine ground calcium carbonate (mean particle size less than 2 microns) and precipitated calcium carbonate. The scope of the paper encompasses four basic areas relevant to the topic: 1. A tutorial overview of the papermaking process with an examination of various industrial mineral components in that process; 2. A discussion of basic technological topics pertinent to the utilization of carbonate in paper with emphasis on the relative aspect. Of natural ground calcium carbonate (GCC) and synthetic precipitated calcium carbonate (PCC); 3. An overview of paper and carbonate market, in both the United State, and Europe with emphasis on (a) current status and future growth trend. Of such market., and (b) discussion of the major influences on growth and development of such market.; and 4. Identification and discussion regarding the principal producers in calcium carbonate markets serving the paper indu.try in Europe and North America.

Jan 1, 1993

The paper discusses the special mixing requirements for Metallurgical Plant Design and outlines the problems associated with the agitation in Mineral Processing Industry today. It also covers new applications such as state of the art large leach tanks and backfill for deep mining.

Jan 1, 2004

By Peter A. Rona

The recent discovery of the first black smoker-type hydrothermal venting and massive sulfide mineral deposits at a site in the rift valley of the slow-spreading Mid-Atlantic Ridge near latitude 26°N, longitude 45°W (Rona et al., 1986, Nature, 321: 33-37), demonstrates that a complete series of hydrothermal mineral deposit types exists at slow-spreading oceanic ridges (half-rate = 2 cm/y), similar to the series previously known at faster-spreading oceanic ridges (half-rate > 2 cm/y). The largest hydrothermal mineral deposit known at a seafloor spreading center is a stratiform massive sulfide body with bulk dry weight of about 100 x 106 metric tons in the Atlantis II Deep at the slow-spreading axis of the Red Sea. This observation invalidates the concept that size of a hydrothermal deposit is directly proportional to rate of seafloor spreading. Instead, the occurrence, grade and size of a hydrothermal deposit formed at a seafloor spreading center is controlled by anomalous chemical and physical conditions which may occur at extremely localized sites at the full range of spreading rates. The basic hydrothermal process involving subseafloor hydrothermal convection driven by magmatic heat sources appears to be similar at slow- and faster-spreading centers. However, differences exist in the periodicity of magmatic cycles that energize hydrothermal circulation (104 y at slow-spreading centers; 103 y at faster-spreading centers); in the distribution of hydrothermal sites along a spreading axis (estimated 100 km along slow-spreading centers; 10 km along faster-spreading centers); and in residence time

Jan 1, 1986

By E. P. Youngman

Except possibly by individual natives and Liberians (small specters), is now being carried on in Liberia, according to a late report. definite information is obtainable with respect to the mineral resources of e country, except that iron ores are said to be abundant. Tin, copper, zinc, site, corundum, lead, bitumen or li nite, and diamonds have all been re- parte, but no commercial Geposits are known to have, been found. Gold has been duce, but not in significant amounts, as may be inferred from the customs - rt for Liberia recording the exportation of gold to the value of $4.80 Germany from the port of Cape Mount in 1925. It is not uncommon for atives to come into towns with African gold and valuable minerals, but they e reluctant to sive information concerning then. Some years ago the Liberian Government was seeing a loan in return for oil concessions, but apparently no drilling bea boon don

Jun 1, 1932

By Yoshinori Kurumada, Masaya Watanabe, Kenji Sasa

"The Port of Yokohama is strengthening its international competitiveness as a strategic container port in order to respond appropriately to global exchange and shipping demands. Thus, the Minami Honmoku main Pier is currently being developed. The high-standard container terminals MC-1 and MC-2 have already started their service, and the development of the container terminals MC-3 and MC-4 is currently in progress.Because the South Honmoku Pier plays an important role in waste disposal management of Yokohama, a final waste disposal site (controlled final landfill site) is being developed in Block 5 to provide long-term and stable reception of waste that will be generated in the city. For this project, a revetment with water-blocking properties and an extension approximately 1.7 km in length is being built in order to prevent water from leaking from the disposal site. The base part of the revetment will be subjected to foundation improvement using the Cement Deep Mixing (CDM) method in order to secure water shielding of the soft sediment underneath the water, prevent slipping of the seawall, reduce the amount of subsidence, and increase the foundation support force.This report presents a preliminary study on using CDM on reclaimed soil and the construction process of the development project of the disposal site in Block 5 of the Minami Honmoku Pier, which has been underway since 2007.ABOUT MINAMI HONMOKU PIERThe development of the Minami Honmoku Pier started in 1990. It was designed to develop high-standard berths with greater water depths in order to handle the increasing volume of foreign container cargo and growing size of vessels. Figure 1 shows the layout of Minami Honmoku Pier. In April 2001, the Phase 1 (MC-1 and MC-2) began services. This is the newest pier in Port of Yokohama.This pier has one of Japan’s largest terminal areas (40 ha) and is equipped with 22 row-type mega gantry cranes capable of handling the newest ultralarge container ships. The pier has a quay with a water depth of 16 m, which is the first in Japan. The pier is equipped with advanced facilities and equipment to let Port of Yokohama be internationally competitive and function as an international commercial hub. An innovative system for high-efficiency transport is currently being introduced; it includes the installation of waiting vehicle lanes and a reservation-based loading and unloading system.Since the fiscal year 2007, a new container terminal (MC-3) with a -20m deep quay capable of handling the increased size of container ships and the diversification of port logistics has been under construction and is nearly completed."

Jan 1, 2015

By H. T. Mercer, A. C. Paulson

The composition of steel and the theory of its heat treatment have been so ably discussed elsewhere that it is unnecessary to go into the subject here. The purpose of this paper is to describe briefly the method of treating drill steel at the Copper Range mines, giving some of the troubles encountered and the manner in which they were overcome or corrected. To study the matter properly, it was necessary to devise a system of records that would show the actual underground performance of the drills. To illustrate this system, the records of the Champion mine are used, as it is at this mine that most of the work along these lines has been done. Reports from each drill machine are made daily by the shop and mine, and tables compiled from these reports show the footage drilled, steel broken, drills received and sent out at the shop, drills sharpened, and bits cut off. These data show what each machine or party is doing and whether the miners' supply of drills is kept up to date. There have been times when the supply of drills has been short and time lost by the miner in looking for drills. The daily records show the number and condition of drills on hand at all times. Under the old method of sharpening, the drills were heated in a coke furnace, the proper degree of heat being judged by color. Then they were sharpened in a machine, reheated in a second coke furnace where the proper heat was again determined by color, and quenched in water. While this method was fairly successful in the hands of a careful workman and for the solid steel used in the old piston drill machine, the introduction of the faster water machine, using hollow steel, produced changes both underground and in the shop. Much more was expected of the hollow-steel and hammer-type machine, with its improved method of rotation, but troubles due to breakage, burnt bits, uneven tempering, etc., at once appeared.

Jan 1, 1922

By H. T. Mercer

THE composition of steel and the theory of its heat treatment have been so ably discussed elsewhere that it is unnecessary to go into the subject here. The purpose of this paper is to describe briefly the method of treating drill steel at the Copper Range mines, giving some of the troubles encountered and the manner in which they were overcome or corrected. To study the matter properly, it was necessary to devise a system of records that would show the actual underground performance of the drills. To illustrate this system, the records of the Champion mine are used, as it is at this mine that most of the work along these lines has been done. Reports from each drill machine are made daily by the shop and mine, and tables compiled from these reports show the footage drilled, steel broken, drills received and sent out at the shop, drills sharpened, and bits cut off. These data show what each machine or party is doing and whether the miners' supply of drills is kept up to date. There have been times when the supply of drills has been short and time lost by the miner in looking for drills. The daily records show the number and condition of drills on hand at all times. Under the old method of sharpening, the drills were heated in a coke furnace, the proper degree of heat being judged by color. Then they were sharpened in a word drill-sharpening machine, reheated in a second coke furnace where the proper heat was again determined by color, and quenched in water. While this method was fairly successful in the hands of a careful workman and for the solid steel used in the old piston drill machine, the introduction of the faster water machine, using hollow steel, produced changes both underground and in the shop. Much more was expected of the hollow-steel and' hammer-type machine, with its improved method of rotation, but troubles due to breakage, burnt bits, uneven tempering, etc., at once began to appear.

Jan 8, 1920

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By R. M. Whyte

The Konkola Deep Mining Project (KDMP) seeks to exploit the deep level potential of the Konkola Deeps orebody, producing high grade copper concentrates for treatment at the Nkana Smelter and Refinery. As an alternative to smelting, Konkola Copper Mines (KCM) has examined a processing route involving pressure leaching of the Konkola concentrates at Nchanga, with the leach liquor being treated by solvent extraction and electrowinning to produce high purity copper cathode. The solvent extraction circuit would be operated to achieve a high ?delta? copper, thereby providing a strong acid raffinate which can be used in the existing Tailings Leach Plant (TLP) to treat Nchanga oxide copper materials. The main focus of the hydrometallurgical option is to capitalize upon the synergy that exists between the treatment of sulphide copper concentrates (acid producing) and oxide copper ores (acid consuming). The paper discusses the key features of a comprehensive piloting campaign carried out at Anglo American Research Laboratories, which involved the co-treatment of Konkola copper concentrates and Chingola refractory ore in a fully integrated pilot plant circuit.

Jan 1, 2001

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By Yoichi Takeda

Copper solubility in Si02-CaO-FeOx slag equilibrated with copper matte in 10% S02 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag. A classical thermodynamic model postulating CUOO.5 and CuSo.; molecules assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated Si02-FeOx binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeOx-SiOrCaO ternary slag saturated with 2CaOSi02 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003