Search Documents

By Randal Martin

Recently, questions regarding the influence of atmospheric temperature and humidity levels on airblast levels have arisen at a number of blast sites. Humidity is alleged to have contributed to high levels of disturbance within communities surrounding blasting. In some cases, local regulatory agencies considered adopting guidelines to specify humidity and temperature ranges under which blasting cannot take place. However, it is normal blasting industry practice not to consider humidity or temperature effects, in the absence of inversions, on airblast levels. When blasting is conducted in the vicinity of residential structures, the influence of weather on the propagation and attenuation of airborne noise from the blasting site is always a concern. Sound naturally attenuates in air with distance from the source. A part of this attenuation is attributed to divergence at the airblast wave front, while the remainder of the attenuation is an accumulation of various factors that include temperature and barometric pressure, absorption in air due precipitation and vegetation, wind and temperature gradients, atmospheric turbulence and topography (Beranek, 1971). Wind speed and wind direction, as well as vertical and horizontal temperature gradients can cause airblasts to focus in local regions surrounding blasting operations and may result in air pressures greater than expected. In fact, wind and temperature inversions can actually increase sound levels with distance from the blast site. Close to the blast site, the effects of inversions may be negligible but may exceed 10 dB at 800 m or greater (Davis and Cornwell, 1991).

Jan 1, 2001

By J. Blodget Britton

DURING the last three or four years I have had occasion to examine, chemically, various samples of matter commonly called flue-dust or cinder, found deposited in the flues and hot-blast chambers and under the boilers of blast furnaces, and also in the flues and under the boilers of puddling and boiling furnaces. Recently several of these examinations were made quite in detail, and as the results reveal, I believe, information of no inconsiderable importance, I am induced to communicate them to this Institute. A sample of deposit obtained from the flues of one of the blast furnaces at the works of the Phoenix Iron Company, at Phoenixville, Pa., was found to have the composition given in Column I of the following table

Jan 1, 1877

By X. Wu, W. R. Chen, J-G. Legoux, B. R. Marple, E. Irissou

Cold gas dynamic spray (CGDS) has been considered a potential technique to produce the metallic bond coat for TBC applications, because of its fast deposition rate and low deposition temperature. This paper presents the influence of spray processes for bond coat, including air plasma spray, high velocity oxy-fuel, and in particular CGDS, on the oxidation performance of TBCs with a Co-32Ni-21Cr- 8Al-0.5Y (wt.%) bond coat. Oxidation behaviour of the TBCs was evaluated by examining the coating microstructural evolution, TGO growth behaviour, and crack propagation during thermal exposure at 1050°C. The relationship between the TGO growth and crack propagation will be discussed.

Jan 1, 2010

By Otis E. Perkins

This paper is one of a series being prepared for the United States Bureau of Mines to disseminate technical information retarding the methods used in mining nonmetallic minerals. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. This paper deals particularly with methods and costs of dredging, classifying materials, and transportation at the plant of the Ross Island Sand & Gravel Co. of Portland, Ore. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Harold Blake, general manager of the company, and of A. V. Kramer, cashier in charge of the plant office.

Jan 1, 1933

By John M. McAnerney

In 1955, the U.S. Army started to experiment in Greenland with tunneling in glacial ice and later in frozen glacial moraine. By 1960, long adits and experimental rooms had been successfully excavated. Full mechanization with coal-cutting machinery was most efficient in ice but drilling and blasting were necessary in bouldery moraine. In 1963, the U.S. Army Cold Regions Research and Engineering Laboratory, (USA CRREL; redesignated U.S. Army Terrestrial Sciences Center July 1, 1968) started a tunnel in the frozen silt of central Alaska near Fairbanks. The original adit of 360 ft (109 m) was successfully driven in the permafrost by a twin-rotor tunnel-boring machine, the Alkirk Cycle Miner. The workings were enlarged in 1966 and 1967 by standard mining techniques in which jackhammers, steam points, and augers were compared. A mechanical coal cutter was tried to supplement drilling and blasting. In 1968, airblasting techniques were used successfully for breaking out the frozen silt. All mine products were loaded mechanically and hauled by self-dumping shuttle car. Pneumatic methods of transport were tried for both dust removal and for conveying blast products up to 3-in. maximum size. Studies of the effects of natural winter ventilation through a shaft showed that tunnel closure could be reduced by lowering the adjacent ground temperature. It is concluded that underground openings in frozen ground should be cut and maintained at well below freezing temperatures to hold deformation to a minimum. HISTORICAL BACKGROUND This chapter deals with aspects of tunneling not previously discussed in the conference papers in this book. The chief differences are that the three tunnels lie entirely within frozen material and are relatively small, since they were constructed mainly for research. The primary objectives of the research were to develop underground shelters for military per-

Jan 1, 1970

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Roger Lafrance

"This paper discusses various aspects affected by the use of large-diameter boreholes in underground mines. Topics covered consist of noxious fumes, vibrations, post-blast effects, various types of explosives, the cordine system in production blasts, the slider primer system and wall-control methods. In general, the paper is an overview of this important fact of underground mining.IntroductionWith economical factors leading the way, many reasons motivated drilling equipment companies to develop equipment that can drill holes up to eight inches in diameter and even larger for underground applications. One of these other reasons is the fact that many orebodies were considered marginal, given the high costs of conventional mining methods utilizing small diameter boreholes. With these criteria in mind, accelerated programs were put in motion to develop equipment that would reduce both-development and production costs in underground mines. Change s in any basic program often affect other areas down the line. This is particularly true with the ad vent of large-diameter boreholes underground.C-I-L Inc. is certainly no stranger to this phenomena. Whether production headings increase in size and tonnage or whether production increases due to lower costs, one fact remains unchanged and that is the fact that all development and production holes are loaded and blasted whether they be of small or large diameter. Due to this fact, C-I-L Inc., as a leading explosives manufacturer, initiated a program to examine blasting methods in use in surface work with the intent of revising these method s for underground applications. Research facilities were also oriented toward developing appropriate products. This was a task that was accepted with anticipation, with the result that many new blasting systems and methods were brought forward, thanks to the collective efforts of both the consumers and manufacturers."

Jan 1, 1984

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By Lei Pan, Roe-Hoan Yoon

"Direct force measurement for bubble-particle interaction has been difficult due to bubble deformation, which makes it difficult to know the separation distances between the two macroscopic surfaces. In the present work, we have developed a method of monitoring the deformation accurately, while directly measuring the interaction forces. In effect, we can ‘see’ bubbles interacting with mineral surfaces under different hydrodynamic and chemical conditions and determine both the hydrodynamic and surface forces involved. In the present work, a high-speed camera has been used to record the optical interference fringes of a thin liquid film (TLF) of water formed on a mineral surface. The recorded fringes are then used to reconstruct the spatiotemporal profiles, from which one can determine the hydrodynamic pressure using the Reynolds lubrications theory. From the forces directly measured in the present work and the hydrodynamic pressures obtained from the fringes, we have determined the disjoining pressure. The results show that air bubbles interacting with hydrophilic surfaces form stable TLFs with zero contact angles. The TLF formed on a hydrophobic surface thins fast, form a ‘pimpled’ film, and ruptures to form a finite contact angle. The new information obtained in the present work may be useful to better understand the role of hydrodynamic and surface forces affecting bubble-particle interactions."

Jan 1, 2014

By T. M. Kegley, J. H. Frye, D. L. McElroy, M. L. Picklesimer, E. E. Stansbury

Measurements of rate of growth, thermodymmic quantities, and partitioning of Mn are reported for high-purity eutectoid Fe-C and Fe-C-Mn steels for the auistenite-pearlite reaction. Evaluztion of the cotnstants of a derived-rate equation with these data indicate that Mn additions cause the decrease observed by increasivg the activation energy and apparent activation entropy or the movenment of complexes at the interface. A diffusion-controlled mechanism is not required. Appreciable partitioning of Mn to cementite occurs entirely behind the austenite-pearlite interface for more than 30°C of subcooling. ThE growth of pearlite from austenite has been extensively studied over a period of years. but the rate-controlling step in the process is not known nor is the mechanisrn of the effect of alloying elements understood. A comprehensive review of the subject has been given by Mehl and Hagel. The present study has been concerned with further considerations of the effects of alloying elements on the rate of growth of pearlite. Analytical relatioriships for the rate of growth of pearlite have been considered by Zener.2 Turnbull,3 Machlin,4 Cahn.5 Frye,6 and Frye et a1.7 The derived expressions in each case involve the free energy of the transformation. the interlamellar spacing. and some rate term of the nature of the diffusion coefficient. mobility or frequency of occurrence of some rate-determining step. The treatments. of course. differ in detail. Further consideration is given in the present paper to the equation of Frye, Stansbury. and McElroy which was derived from modified absolute rate theory without in any way specifying the mechanism of the reaction. This equation is r=c ? T ? F exp -?E*/RT [1] where r = rate of growth in mm/sec c = a constant AT = equilibrium transformation temperature minus actual transformation temperature "C ?F = free energy per mol of austenite minus that of pearlite ?E* = activation energy R= gas constant ?F in Eq. [1] is computed from the following: ?F=?H?T/To - ?T' dT' ?T' ?CdT"/T" [2] To To where AH is the enthalpy per mol of austenite minus that of pearlite at the equilibrium temperature, To, and AC is the difference in specific heat between austenite and pearlite per mol. Subsequently, Darken, Fisher, and Galligan8 have reported that a layer of ferrite separates pearlite from austenite at the growing interface (i,e., the advancing face of Fe3C is in contact with ferrite, not austenite) and the ratio of the thickness of this layer to the spacing of the pearlite has not been found to vary with alloy content or transformation temperature. This observation does not require any alteration in the above equation: however, it may require that a different significance be attached to the factor, AT. The AT term appears in Eq. [I] as a consequence of a factor for the amount of growth per complex transformed at the interface.* It is based *This is not the sole reason for expecting such a relationship. See Ref. 7._______________________________________________________ on a l/2 ?T dependence of the interlamellar spacing. Zener2 has developed a theory which leads to Soa 1/?V where So = the pearlite interlamellar spacing. This relation is as consistent with the data on interlamellar spacing as other relationships, although, as pointed out by Mehl and Hagel,1 the data are not sufficiently precise to consider the relationship as confirmed. The work of Darken, Fisher, and Galligan8 requires that the above be written where f = the thickness of ferrite layer between austenite and pearlite. The present paper is concerned with iron-carbon-manganese eutectoid alloys and reports experimental measurements of the following kinds: 1) the effect of

Jan 1, 1961

By Albert Brokaw

THE so-called ?paraffin dirt" of the Gulf Coast oil fields has been con¬sidered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described' as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist.

Jan 4, 1918

[ ] ST. JOSEPH Lead Co., is entering the oil business. Andrew Fletcher, St. Joseph president, stated that plans call for a contract with the Continental Oil Co., to drill 11 exploratory wells. Six will be in Texas, one in southern Louisiana, one in northern Louisiana, and one each in California, Oklahoma, and Montana. St. Joseph is also negotiating a contract with the Zephyr Drilling Co., for wells in Wyoming and Colorado. St. Joseph is planning to drill another well on a 6000 acre plot in southern Illinois. Proxies issued before a special meeting of the board, said the new venture is not intended to change the general character of the company's business, or to involve a significant part of its resources. If gas, oil, or minerals are discovered in paying quantities, the company will develop and operate the deposits and dispose of the products for the joint account of Continental Oil and St. Joseph Lead. The mining company will contribute a proportionate share of the cost, but will have definite limitation of its obligation. The amendment to St. Joseph's certificate of corporation, passed by the board meeting, also extended the power of the company to include mining operations of all kinds.

Jan 1, 1952

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

Active avalanche control is the intentional triggering of avalanches while people are kept out of the hazard area. Explosives are frequently the most effective tool for triggering avalances. In a highway setting an avalanche control program will reduce total highway closure time, while providing greater safety to motorists and maintenance personnel. Avalanche control with explosives is effective when the snow is somewhat unstable and almost ready to slide naturally. Forecasting this condition involves having a network of local meteorological stations, examining snow structure, using mountain weather forecasts, doing snow strength tests, and having the results of ski and explosive tests. The method of delivery of explosives to an avalanche starting zone is governed by the accessibility of the starting zone. Common methods include; hand placing or throwing charges, remote delivery cableways, or "trams", surplus military weapons, and a compressed gas charge launcher, or "Avalauncher". Charges dropped from helicopters are also occasionally use. We have increased the effectiveness of our program by use of large elevated charges. Efforts are being made around the world to develop and utilize better methods for the safe, remote initiation, but procedures have varied dramatically between individual control programs. There is now a movement to review and standardize operational guidelines for avalanche control. Highway avalanche control is often done at night, during winter mountain storms. Heavy rain or snow, high winds, and high avalanche hazard, are common work site conditions. Commercial and economic pressures are increading, so methods that redice highway closure time are important. There are also many safety issues to be addressed in avalanche control work.

Jan 1, 2002

Morning Star Gold aims to enter the ranks of Australia's gold producers, revitalising the Eastern Victorian Goldfi elds in the second half of 2010 - the fi rst gold production in around 50 years from the Morning Star Gold mine, which was once Australia's largest under WMC. This presentation will outline the redevelopment of the Morning Star Gold Mine from exploration to production. Morning Star Gold NL's (MCO) key project area is centred at the historic mining town of Woods Point and nearby Matlock (to the southeast) and Gaffney's Creek (to the northwest), all of which are located in the lower part of the Victorian Alps roughly 60 kms south of Mansfield. Morning Star has literally numerous historic mines and gold bearing 'dykes' on its tenements, many with a rich production history of high-grade gold from quartz reefs and alluvial sources. The area encompassing the Woods Point goldfi eld and the multiple high-grade gold bearing dyke structures located north towards Jamieson and south towards Walhalla formed one of the most significant mining fields in Australian history. Historical gold production was at least 155 t or around six million ounces of over a century of mining with an average production grade exceeding 27 g per tonne. The bulk of this recorded production came from just a handful of mines and of those only three were mined to any great depth. One of the key historical production hubs in this area was the famous 'Morning Star' mine, which is situated adjacent to Woods Point township. The Morning Star mine produced almost one million ounces at 27 grams per tonne, operating fairly continuously between 1861 and 1959 with a break after Jan 1939 due to the devastating 'Black Friday' bush fi res across eastern Victoria. During the early 1940s, the Morning Star was Australia's biggest gold mine. The Morning Star mine along with Walhalla ensured that this goldfield was third behind Bendigo and Ballarat as Victoria's biggest hardrock gold production centre. Morning Star Gold has rebuilt its 100 per cent owned 'Morning Star' mine with a view to producing gold in the second half of 2010. Morning Star is exploring its regional dykes in order to estimate an overall gold endowment and rank local production sources to feed its proposed mill at the Morning Star mine site. Key initial targets (all within 11 kms of the Morning Star mine) are the Waverly, All Nations, Rose of Denmark, Hunts, Wallaby and Loch Fyne dykes, all of which historically produced high grade gold, much of it gained from only shallow workings above the water table in the weathered zone of rocks. Historically the Morning Star mine was developed over 24 levels to a depth of 940 m via one large vertical shaft and a smaller, deeper inclined shaft at the 1900 feet level underground. At present MCO has dewatered and completely refurbished all infrastructure to the ten level (~310 m below surface). MCO knows there are a number of substantially under-explored and undeveloped or partially developed but not stoped areas within the Morning Star mine. As a result, MCO has been carrying out extensive channel sampling and an underground diamond drilling program targeting areas of the mine that were largely unexplored and undeveloped by the last operators of the mine - Western Mining Corp Ltd (Gold Mines of Australia). Four thousand, fi ve hundred pages of archival WMC records have helped the cause significantly. The shaft refurbishment and reconstruction stage is complete. This has been a program that originally commenced back in 1993 and has cost around $22 M. This refurbishment paved the way for the extensive underground resource focused diamond drilling program, which MCO completed in 2008 with two company-owned and operated drill rigs from drill cuddies on level 9 (900 feet underground) of the mine. This drilling, which encountered some stunning grades intersections and multiple visible gold hits, has outlined further production opportunities including 0.4 m @ 1392 g/t Au (MS 410). Metallurgical testing conducted by Gekko Systems of samples obtained from the exploration program found gravity concentration and a leach circuit gave recoveries of ~95 per cent to 99 per cent, or ~92 per cent from gravity alone at a coarse crush (300 ¦m). Currently, the plan is to use gravity to fi rstly produce dore bars on-site from the free milling gold and secondly a saleable concentrate for CIL processing off-site. A purpose built 10 t/h (~80 000 t/a) gravity treatment plant was subsequently ordered from Gekko and is expected to be installed onsite and commissioned in the Q3 2010. The plant features fi ne crushing with a vertical shaft impactor, followed by gold concentration by inline pressure jig, inline spinner and Wilfley table. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By J. Michael Howard

Holes cored through the Prairie Creek lamproite volcanic complex at the Crater of Diamonds State Park by companies interested in the site's commercial diamond potential give an opportunity to redefine the size and shape of the Prairie Creek pipe. Relationships of cored rock sequences and the discovery of a previously unrecognized major rock type allow a reinterpretation of the sequence and type of intrusive activity. Trench sampling of diamondiferous rock units yielded a diamond content far below what was anticipated based on an estimate from historical records. Inadequacies of shallow bulk-testing methods for a diamondiferous pipe are examined.

Jan 1, 1999

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021