Search Documents

By L. F. Elkins

Water coming into wells with bottom water present in the Fosterton field, when their oil recovery was only 0.1 to 1.5 per cent of oil in place below the lowest perforation, confirms lack of shale barriers to vertical flow which also are not apparent in cores and electric logy. Low contrast of vertical and horizontal permeability, high mobility ratio betweerz oil and water zone and pos.rible rate effects due to gravity Combine to prevent easy analysis of water invasion pattern and efficiency by analogy or intuition. Theoretical analysis of performance including these factors using a new direct nurnerical .solution of potential distribution in a network led to unanticapted indications that water would under-run the entire oil reservoir with low volumetric coverage if supplied through natural influx or peripheral water injecfion below the oil-water contact. An unusual pattern of water injection is to he adopted in this recently unitized pool to provide more uniform water flooding in that two-thirds of the oil reservoir not underlain by bottom wafer. INTRODUCTION The Fosterton field, Southwestern Saskatchewan, Canada, was discovered in Jan., 1952. It produces at a depth of 3,100 ft from a pinch-out of the Roseray sand at the Lower Cretaceous-Jurassic unconformity. The field, covering 2,500 acres, contains 54 wells on 40-acre spacing. Development was essentially complete in June, 1954, but significant production did not start until May, 1955, when a pipeline outlet became available. Within one year rapid in- creases in gas-oil ratio and early encroachment of water created operating problems in the down-structure eastern half of the field and raised serious questions about reservoir performance and ultimate recovery. This paper describes the unusual behavior of water encroachment—on both well and reservoir bases—and the analyses made to interpret it. The field was unitized July 1, 1958, for water flooding. A somewhat unconventional

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By C. J. Newman, K. Molnar, A. G. Storey, G. Macfarlane

"The Kidd Creek copper smelter started operation in June 1981 using the Mitsubishi Continuous Smelting Process. A steady increase in plant production rates has been demonstrated, and the annual tonnage of concentrate smelted is now double the original design rate. This paper summarizes recent modifications made to increase concentrate feed rates, increase on-line time, reduce copper losses and control the impurity level in anode copper. It includes improvements made to furnace design, improvements to reduce downtime f or boiler cleaning, and improvements made to the acid plant to allow handling of increased gas flowrates and higher gas strengths while maintaining low acid plant emission rates. IntroductionThe Kidd Creek Division of Fal conbridge Limited operates a base-metal mining and metallurgical complex, located in Timmins, Ontario, which includes an underground mine, a 13 500 tonne/day concentrator, a 130000 tonne/year zinc plant and a copper smelter and refinery, The copper smelter and refinery were commissioned in 1981, with an installed capacity of 59 000 tonnes/ year of cathode. The smelter, utilizing the continuous smelting technology of the Mitsubishi Process, has subsequently been expanded in production capacity, and in 1991 produced 113 500 tonnes of blister copper The capacity of the refinery, which uses Onahama No. 3 tankhouse technology, has been increased to 96 000 tonnes/year of cathode. The capacity increase at the smelter has been realized through the input of additional oxygen to both the smelting and converting furnaces, without increasing the process off-gas flowrate through the associated waste heat boilers.In this paper, a brief review of smelter operation and modifications in the period 1982 to 1987 is presented, together with a more detailed discussion of operation during 1988 to 1991, and a discussion of future planned improvements."

Jan 1, 1992

By Georgy Cherkashov, Svetlana Babaeva, Tamara Stepanova, Firstova. Anna

Seafloor massive sulfides (SMS) study in the Russian Exploration Area at the northern equatorial Mid Atlantic Ridge began after signing the contract with International Seabed Authority in 2012. In order to evaluate the SMS resources in the course of exploration the major and rare metals with economic value should be determined. The evaluation is based on geochemistry and mineralogy and particularly on the type of rare metals occurrence in the SMS. As a case study research of the Semyenov cluster of SMS deposits have been conducted.

Sep 1, 2014

By W. Laird

For years, the coal industry has been confronted with face ventilation problems, ignitions, dust, and their effect on productivity. To improve face ventilation, minimize face ignitions, and control dust in the face areas, studies have been conducted over the past 30 odd years by coal companies, federal government research programs and others. These studies included brattice curtains, water spray nozzles, water pressures, highly efficient water filtration systems, auxiliary fans, differ fans, various dust collection systems and the recently developed "Spray Fan" ventilation system. This system consists of spray banks strategically placed on continuous miners to ventilate immediate face area.

Jan 1, 1984

By P. Thareja, V. Prasad, S. P. Mehrotra

In recent times, the transportation of minerals and their tailings has become a major concern across the world. There exists a huge demand of efficient and cost effective transportation system which poses minimum environmental damage. One of the economically and environmentally viable techniques which potentially offer a solution to the above problem includes transportation of minerals and their tailings in the slurry form through pipelines. Slurry transportation through pipelines is reported to be more beneficial in terms of cost, environmental impact, maintenance and safety when compared with other conventional modes of bulk transportation such as train, truck, barge and conveyors. The main challange associated with hydraulic transportation of slurries is to obtain a non-settled slurry and to design a pipeline system which results in the optimum energy requirement for transporting a large throughput to longer distances at a lower cost. The feasibility of hydraulic transportation of slurries through pipes mainly depends upon slurry properties and flow conditions in the pipe. Results from rheological studies exhibit the presence of shear thinning flow behaviour of minerals and their tailings in water. The flow behaviour index (n) and consistency coefficient (k) obtained from the rheological analysis are further used for the specific energy consumption and energy losses during transportation. The cost of transportation in USD per ton per 100 km and transport capacity in tons per day are calculated from the specific energy consumption to transport these slurries. The results demonstrate that the slurries can be transported to long distances (say, 100 km or more) corresponding to optimum energy consumption and dissipation rate at a substantially cheaper cost than the existing rail and road transport in India. Although we have carried out transportation studies with coal fly ash (CFA), lignite & bauxite slurries, for paucity of space, the results reported here are essentially for CFA slurries. Details of our investigations with lignite coal & bauxite will be reported seperately.

Jan 1, 2018

By D. W. Morgan, K. W. Downes

"OVER half a million tons of chromite ore is used annually on the North American continent, all of which is imported from overseas. Chromite is essential in the manufacture of stainless steel, armour plate, and tool steel, to mention only three important uses. It is, therefore, a strategic mineral, and every effort should be made to discover a means of utilizing our domestic supplies.Both Canada and the United States possess deposits of chromite, but they are low grade with respect both to their chromium content and to the ratio of chromium to iron. Mechanical concentration can improve the chromium content •by rejecting gangue, but chromium concentrate produced is still lower in chromium than imported chromite and, more important, the ratio of chromium to iron is only about half that in the imported material. At present, a chromium to iron ratio •of 3:1 is desired by industry. To obtain this .ratio in the case of domestic ores, a chemical attack on the chromi'e is necessary."

Jan 1, 1952

By N. S. Stoloff, R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-Co and Fe- V alloys containing up to 25 pct solute have been studied in the temperature range 25° to - 196°C. The microyield stress is independent of temperature for all alloys studied, while the temperature dependence of the ordinary yield stress is large and comparable to that for unalloyed iron. An alloy-softening phenomenon is observed for many alloys relative to unalloyed iron, and appears to be a consequence of removal of inter-stitials from solution and their subsequent agglomeration. The ductile to brittle transition temperature is increased markedly by both cobalt and vanadium. Transmission electron microscopy observations reveal that cross slip and cell formation are restricted with increasing solute, which can account for many aspects of yielding and fracture behavior. IRON and other metals of bcc structure slip on many planes of the (111) zone at moderate and elevated temperatures, giving rise to wavy glide. At low temperatures, however, there is a tendency for slip to be restricted to planes of only one or two crystallographic types; in the case of Fe-Si alloys for example, (110) glide predominates, giving rise to planar slip bands."' Restriction of cross slip at low temperatures in iron has been linked by Brown and Ekvall3 to increased strain hardening in the preyield microstrain region, leading to an apparently large temperature dependence of the yield stress. Support for this view has been provided by Lawley and Gaigher4 from a transmission electron microscope study of molybdenum. They concluded that dislocations at lower temperatures, by virtue of their inability to change planes readily, are unable to interact and annihilate, leading to an increase in internal stress and work-hardening capacity. Restriction of cross slip at low temperatures has also been suggested to be an important factor in determining the ductile to brittle transition of single-phase solids, including metals of bcc structure.5 It is pertinent to note that most solute elements tend to raise the ductile to brittle transition temperature of poly crystalline ferrite,6,7 although in some cases, e.g., Fe-Cr7 and Fe-Al,8 the dilute alloys may actually yield at lower stresses than unalloyed iron. It appears, therefore, that solute elements may have an effect analogous to lowering the test temperature with regard to restricting cross glide. Such an effect has indeed been observed in the ionic alloy system KCl-KBr,9 in which bromine atoms, although causing little misfit and consequently little effect on the yield stress of KC1, have a pronounced effect in restricting wavy glide and inducing brittleness. The purpose of the present investigation was to determine the effects of selected solute atoms on the yield stress and fracture behavior of iron, and to elucidate in turn how the slip character was related to these properties. Since it is known that interstitial atoms exert a strong influence on the mechanical behavior of iron, the solute elements chosen for study were vanadium, which reacts strong with interstitials,10 and cobalt, which does not form highly stable interstitial compounds." EXPERIMENTAL PROCEDURE Four-pound ingots of each of the following alloys were vacuum-melted in zirconia crucibles: Fe-1, 5, 10, 25 at. pct Co, and Fe-1, 4, 10, 20 at. pct V. An ingot of unalloyed iron from the same original stock as that used for the alloy was remelted under similar conditions to eliminate variations in interstitial content arising from differing thermal histories. Chemical analyses of the iron, cobalt, and vanadium melt stock are listed in Table I. All ingots were rolled and swaged, commencing at 850°C, to 1/4-in.-diameter bar. The bars were then annealed at 850°C for 1 hr (except that the 10 and 20 pct V alloys were heated for 2 hr) to give a uniform equiaxed grain size of about 0.05 mm. Tensile samples of 0.125 in. diameter by 0.8 in. gage length were utilized for studies of the ductile to brittle transition. A second set of tensile samples were utilized for microstrain experiments in which strain sensitivity of 1 x 10"6 was achieved by a capacitance method.3 Cylindrical compression samples 0.250 in. diameter by 0.4 in. long also were prepared to study the influence of composition on the macroscopic yield stress, and for metallographic analyses of defor-

Jan 1, 1965

By A. Rahimi

The smelting plant at Sarcheshmeh Copper complex commenced working with two reverbatory furnaces, four pierce smith converters, two anode furnace and one holding furnace having a known capacity of 420 metric tons of anodic copper according to the initial design in 1982 (1361 Iranian calendar). During the period from the commencement date up until now, the smelting plant has undergone changes for improvement and enhanced production by substituting holding furnace with another anode furnace, installing the fifth converter and utilizing oxyfuel burners on the ceiling of the reverberatory furnaces. According to the different operational processes in reverberatory, converter and anode furnaces different types of corrosion mechanisms and degradation can be observed in the refractories of copper smelting furnaces. In the case of reverberatory furnaces, the corrosion and degradation of refractories may be factors such as hot corrosion by melt, corrosion attack by the constituents of burning fuel, degradation of sidewalk exposed to mechanical stresses of the feed charge and the hydrostatic pressure exerted by the melt inside the furnace, all of which are due to the unique operational condition governing the reverberatory furnaces environment, i.e. burning fuel atmosphere, charge concentration and combination, furnace temperature, calm melt condition, etc. In the case of converter furnaces, the most likely corrosion and degradation of refractories may be due to the chemical reaction between the melt and degradation of tuyere zones due to sever movement of the melt and mechanical strikes of the punch rod. Also the most essential corrosion reaction occurs around the mouth of the converter because of the mechanical strikes by the cleaning device and thermal heat shock. Other parts inside the furnace are corroded due to the reactions between the fayalite slag and the furnace refractory. In anode furnaces the degradation mechanism is mostly related to the gaseous corrosion (penetration of natural gas or liquid gas inside the refractory structure due to the long period of reduction processes and refining stages. Finally another important factor responsible for destruction of refractories in these furnaces is the copper oxide slag together with the fume constituents of burning fuels.

Jan 1, 2004

By J. H. Adkins

The goal of this program was to produce a set of baseline health and safety training materials that could be used by the metal/nonmetal mining industry to reduce injuries and to comply with federal training requirements. The materials developed are arranged in a two level outline format. The first level provides the title, course goals, background and topical outline while the second level provides a detailed outline of the course content. Visuals, designed to portray miners in a positive, attractive fashion, were done in simple line drawing so they would reproduce for handouts without loss of quality. Each of the required units in the Baseline Guides have one or more self-checks. These are designed to be suggestive of evaluation techniques the users can develop for themselves. An instructors guide and a mining terms glossary are included. In a second phase the program developed performance based training guides for Annual Retraining and Experienced New Hires in the Underground Salt Industry.

Jan 1, 1983

By R. W. Sayers

The Duval Corporation porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an economic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex copper-gold-silver ore is treated in a 4,000 tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamorphism and hydrothermal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes further altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle Formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony Formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls.

Jan 1, 1968

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

By A. M. Guadin

Direct quantitative comparison of the results of concentrating operations on different ores is frequently desired but almost impossible to obtain if comparison has to be made by means of two quantities for each ore, as must be done at present. This paper represents the outgrowth of attempts to arrive at a single-number quantitative measure of the segregation between minerals or metals as the result of concentrating operations. The usual practice in estimating the effectiveness of concentrating operations, particularly those of ore dressing, has been to determine the recovery of the metal or mineral of interest and the grade of the concentrate. The difficulty in quantifying the effectiveness of concentration by the usual criteria may be illustrated by a few examples. Consider, for instance, two lead ores which yield by flotation the same recovery of lead, say 92 per cent., and the same grade of concentrate, say 60 per cent. Pb. If a substantial difference in the grade of the feed had existed, say if one ore contained 5 per cent. Pb and the other 10 per cent., it is clear that the concentrating operation was more effective in the case of the lower grade ore. It is difficult, however, in the light of these data to state how much more effective was the concentration of the lower grade ore. Consider again two lead ores containing 5 and 10 per cent. Pb and yielding concentrates containing 60 and 72 per cent. Pb respectively, with recoveries of 93 and 92 per cent. respectively; it is well-nigh impossiblc to tell from these figures which results represent the best separation of the minerals. It may be noted that in the usual method of estimating the effectiveness of the segregation of mineral values, no consideration is given to the rejection of the unwanted substances from the concentrate, except in the very indirect manner in which it enters into the grade of the concentrate. Consideration of the rejection of gangue from the concentrate, adequately weighted with recovery of the desired mineral in the concentrate, should supply an adequate criterion of concentration effectiveness.

Jan 1, 1930

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923

By Charles P. Berkey, Joseph H. Sinclair

This paper describes the results of a visit to the Santa Elena Peninsula, Ecuador, in January and February, 1921. On account of the complicated folding and faulting of the rocks and the peculiar occurrence of petroleum, field work was possible on only a few of the many geological problems and the results here published are only a contribution to the solution of the general problem. We know of nothing published on the geology of the district, except one account, in Spanish and German, by Theodor Wolf. The Santa Elena peninsula, the most important headland of the coast of Ecuador, lies two degrees south of the equator. The chief town, Santa Elena, is about 75 miles west of Guayaquil, the main seaport of Ecuador. The nearest developed oil field is the Zorritos of northern Peru, 120 miles south across the Gulf of Guayaquil. If newspaper reports are true, viz. that the Anglo-Ecuadorian Oilfields, Ltd., has recently brought in a 700-bbl. well on the coast of the peninsula near Ancon, the district may become important in the production of petroleum. At the time of our visit, the best way to reach the peninsula was by a steamer of the Pacific Steam Navigation Go., southward from Panama and northward from Guayaquil. About once a week, one of these steamers anchored 1/2 mile off shore near the village of Salinas, an important cable station. An alternative route, in the dry season, is by automobile from Guayaquil. In February, 1921, a railway bed had been graded part way between Guayaquil and Salinas, but this was detcriorating rapidly because of lack of funds to continue construction or to keep in repair that portion already completed.

Jan 1, 1923

By G Gibson

Realising that current roadway development performance levels were unlikely to sustain new generation high-capacity (15 Mt/a) longwall mines then being planned, the Australian Coal Association Research Program (ACARP) established a Roadway Development Task Group (RDTG) in 2005 to develop a research strategy targeted at improving roadway development performance in Australian longwall mines. The initial phase of the project identified a number of factors that differentiated best practice mines from others, and proposed a multi-faceted research strategy encompassing both short- and long-term research initiatives, including:conducting regular benchmarking studies across the industry to identify factors contributing to improved performance and to monitor performance trends,conducting regular industry roadway development operatorsÆ workshops to facilitate the transfer of successful roadway development improvement initiatives throughout the industry and facilitate networking between development practitioners,development of alternative skin reinforcement and containment measures that would eliminate the use of steel mesh and enable face support systems to be fully automated,development of automated bolting and mesh handling systems that would enable operators to be removed from the immediate face area,development of a body of knowledge of industry roadway development practice,development of a web-based information management system to capture and transfer emerging developments in roadway development practice and technology,reviewing the Australian civil tunnelling and underground metalliferous mining sectors to identify practices and technologies that could potentially be utilised to improve roadway development performance, anddeveloping a new generation high-capacity mining system capable of +10 metres per operating hour for 20 or more hours per day (CM2010). The paper reports on the progress of the above initiatives and outlines strategies to continue the pursuit for improved roadway development performance.

Jan 1, 2008

By E. Miller, J. M. Eldridge, K. L. Komarek

Aclivilies of magnesium in liquid Alg-Si alloys have been delermined between 5 and 60 at. pcl Si, close to the melling point of Mg2Si, by an improved isopieslic melhod. Silicon specinrens, held in alumina crucibles and graplrile conlainevs of special design, were healed in a letrlpevalure gvadient and equilibrated with mag-nesilcrrl rapor in a closed lilanium system. The ther-madynamic Junctions were calculated and compared with the thermodyuamic properties of the other three mg- Gvoup IVB systems. Lattice paramelers of three Mg2X compounds were measured. The bonding in the Mg2X compounds is largely covalent with small and uarying amounts of metallic and ionic conlvibutions. The Mg-Si phase diagram1 has one congruent melting compound, Mg2Si, of essentially stoichiometric composition, two eutectics, and very limited terminal solid solubilities. Little information is available on the thermodynamic properties of this system. The free energy of formation of Mg2Si has been determined by the Knudsen cell technique2 in the range 572" to 680oC, by the transportation method3 between 858" and 950oC, and by the electromotive-force method4 in the range 400o to 600°C. Kubaschewski and villa5 and caulfield6 have measured the heat of formation of Mg2Si. An electromotive-force study of magnesium-rich liquid alloys was recently published by Sryvalin el al.7 The present investigation was undertaken to complete a general survey of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,a9,Mg-Sn,10,11 mg-Ge,12and Mg-Si. An isopiestic technique, previously developed for similar measurements on liquid Mg-sn11 and Mg-Ge alloys,12 was modified for the Mg-Si system. Specimens of the nonvolatile component, silicon, were contained in dense alumina crucibles placed inside covered graphite crucibles which were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure. The alumina crucibles prevented contact between the highly corrosive liquid Mg-Si alloys and graphite. The graphite cruci- bles effectively preserved the high-temperature equilibrium composition of the liquid alloys containing highly volatile magnesium on termination of the experiments during the quench to room temperature. EXPERIMENTAL PROCEDURE Silicon of semiconductor-grade purity (E. I. du Pont de Nemours and Co., Brevard, N.C.) and 99.99+ pct Mg (Dominion Magnesium Ltd., Toronto, Canada) were used. Graphite crucibles with press-fitted lids were machined from high-density (1.92 g per cu cm) rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The alumina crucibles had a purity of 99.7+ pct (Triangle RR grade, Morganite, Inc., Long Island City, N.Y.). In preliminary runs the liquid alloys were contained in graphite crucibles following the exact procedure developed for the Mg-Ge system.'2 These runs failed due to appreciable reaction between the molten Mg-Si alloys and graphite, and the results have been discarded. The procedure was then modified and the Mg-Si alloys were subsequently held in alumina crucibles. For most of the runs alumina crucibles of known weight and approximately 6.3 mm ID, 12.5 mm height, 1.0 mm wall thickness were loaded with weighed amounts of silicon and encapsuled in tightly covered weighed graphite crucibles 5/16 in. ID, 2 in. helght, 3/32 in. wall thickness). The graphite crucibles were machined from rods which were 85 pct of the theoretical density. These crucibles were therefore sufficiently porous so as to permit magnesium vapor to effuse through the silicon under the experimental conditions of approximately 970O to 1220°C and 1 day equilibration time. However, negligible magnesium was lost from the crucible during the quench due to the slow effusion rate through the pores of the graphite. The inner alumina crucible prevented the liquid alloys from contacting the graphite, and the very tightly fitting graphite crucible lids served to retain any magnesium vaporizing from the alloys inside the crucibles during the quenching step.12 The loaded silicon-alumina-graphite cells were positioned, one above another, on a 16-in.-long titanium thermocouple well and tied securely to the titanium tube with thin molybdenum wires held in grooves around the circumference of the graphite crucibles. A thin (0.005-in.) molybdenum strip prevented contact between the graphite crucibles and the titanium. This assembly was lowered into a titanium reaction tube (la in. ID, 16 in. long, $ in. wall thickness) closed on one end which contained a 11/2-in.-long cylinder of magnesium at the bottom. The inner titanium thermocouple well was positioned eccentrically in the large tube because of the eccentric mounting of the cells on the well. Appropriate modifications of the titanium cap"'12 were made to join the inner and outer titanium

Jan 1, 1968

By Wei Wei

Mining induced ground movement and/or stress redistribution could cause ground instability issues. This is particularly true when the extraction of large stopes is done with one or two large production blasts. Often enough, it is the nearby mine development like haulage drifts and cross cuts that are influenced the most by production blasts. Proper and timely mitigation of ground control issues due to stress redistribution is required. This is usually done by drift rehabilitation involving the installation of secondary support system in the affected areas of the mine development which include; slashing, wire mesh, and in some cases the use of shotcrete liners. It is imperative that such rehabilitation be implemented to the mine infrastructure in a timely manner in order to avoid aggravated ground control problems and production delays. If the real time performance of the support system is captured, it would be possible to determine the timing for rehabilitation job. Birchtree Mine in Thompson, at the Vale Manitoba Operation, has begun mining the 84 Deep Orebody. One of the identified risks is the stability of the crusher room under mining induced stress redistribution. It is proposed to use the U-Cell technology to monitor the primary support system performance (rebar bolts and extension bolts) and monitor the real time performances of the bolt axial loads. The U-Cell technology is a 7-inch long, coupler load cell that is screwed onto the threaded portion of a rock bolt prior to installation. Rehabilitation in the vicinity of the crusher area where U-Cells are installed is recommended when the bolts have reached 70% of their yielding capacity. Catastrophic ground failure can be avoided by adding secondary support in a timely fashion. This paper presents a case study at Birchtree Mine in Thompson Manitoba, where the performance of primary ground support system is monitored and recorded during production.

Jun 1, 2012

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979