Search Documents

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By Lynn B. Hales

Unfortunately, the term "control" has a negative connotation in the minds of many of our operating plant personnel. Whereas the opposite is true of those associated with research and technical centers in our industry. The magnitude of this difference in opinion and actual experience has often proved to be a major factor influencing the success or failure of process control applications. Through the years, many plant people have endured a number of unsuccessful attempts by "outside" people to "optimize" their plants; and these experiences have proved to have had quite a callousing effect on them. On the other hand, in many plants, successful process control efforts have made firm allies of the operating personnel, and have increased the number of metallurgical people who are well qualified and experienced in process control. The instrumentation industry, computer industry, and the mining industry's ability to quantify what is really happening in our processes have grown and developed rapidly since the first control efforts were made in the 1930's (1). Because of this-,: new control opportunities are becoming increasingly more feasible and older well established ones are becoming even more practical and necessary with regard to the economic s of our industry.

Jan 1, 1979

Getting it right is a very profitable outcome. Shareholders would ideally like to see their directors get it right all the time on the major economic decisions. But it is very difficult for mining directors to get it right all the time in such an uncertain environment. Primary decision-makers of companies with significant stakes in the mining industry should get it right much more frequently. The legal measures of evidence (beyond reasonable doubt and on the balance of probabilities) can be used to determine whether grade estimates (a key revenue variable) are realistic. The application of this approach can be far reaching. More frequently correct decision-making would result in more effective allocation of limited resources (capital and labour). In turn, this would result in higher financial returns and a more extensive mining industry.

Jan 1, 1994

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By Donald J. MacNeil

THE opinion, based upon geological knowledge, that certain areas within the Province of Nova Scotia might yield commercial quantities of petroleum, is not new. It dates back to at least 1864, when the Pioneer Oil and Salt Company drilled some shallow holes in search of oil near lake Ainslie, Cape Breton. As a matter of fact, several companies were engaged in oil exploratory work near lake Ainslie at about that time; included among them were the Inverness Oil and Mining Company, the Victoria Oil Company, the American Oil Company, and the Cape Breton Oil and Mining Company. Oil exploration by these and other companies was conducted sporadically on Cape Breton island until 1914. In several instances, the depth of the test holes exceeded 1,000 feet; the deepest was carried to 3,260 feet. The Lake Ainslie area was selected because oil seepages were present along certain sections of the lake shore, but the tests that were drilled to tap the oil-bearing zone failed to yield anything of commercial value. Currently, there are three areas in Nova Scotia wherein active exploratory work is being conducted, namely, at Pugsley Siding close to Amherst; at Kennetcook, Hants county; and near Mabou, Inverness county. The Pugsley Siding test is being drilled by the Sun Oil Company, of Philadelphia; the work at Kennetcook is under the direction of the Nova Scotia Oil and Gas Company; two relatively deep holes were drilled by the Lion Oil Refining Company in 1944 near Mabou, and, as a result of the additional geological information derived therefrom, another test probably will be drilled by this Company in the same area. Aside from these activities in the search for petroleum, the oil possibilities of several other sections of the Province are being studied by means of surface geological mapping.

Jan 1, 1945

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By David S. Holmes

An overview of existing biological technologies for the recovery of copper and uranium is presented. Engineering and biological challenges and opportunities in these areas. are discussed. New opportunities for the biooxidation of refractory gold ore are described. Techniques for the development of new strains of microorganisms. for commercial metal recovery applications are discussed with special reference to the genetic manipulation for bacterial strain improvement.

Jan 1, 1991

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By Alton G. Woody

Like so many installations of its type approaching middle age, the ore processing and shipping facilities in Puerto Ordaz, Venezuela, have taken a lot of twists and turns in their lifetime. The object of this paper is to lead you through these twists and turns and some of the reasoning for them. The need for additional sources of iron are in the United States became evident during the time of the second world war. An exploration team from U. S. Steel located further high quality direct shipping iron are in commercial quantities near Ciudad Bolivar, Venezuela in 1947. Basic decisions were made to develop these reserves for export via the Orinoco River through a new shipping port to be built at the confluence of the Orinoco and Caroni Rivers. The basic concept was for the ore to be loaded directly to ocean going vessels. This was something of a gamble since the basic economics depended upon successfully opening up the main channel of the Orinoco River to deepwater vessels, and the Bethlehem Steel mine in the same area was already working with shallow draft river boats and a transfer station on the coast. Always, the basic philosophy has tended to be to plan with expansion in mind. The original conveyor systems were 1.52 m (60 inches) wide with 200 idlers, whereas 1.07 m (42 inches) or 1.22 m (48 inches) wide conveyors could have carried any production foreseen at the time of installation. Stockpiles have been located and designed with room for expansion. Basic designs have had dotted line future expansion blocked in.

Jan 1, 1978

By M. Zamalloa, P. J. Mackey, P. Coursol, Y. Prévost

"Over the last decade or so, the availability of commercial thermodynamic modelling packages, such as FactSageTM, have been utilized to help the plant optimize slag chemistry and to minimize slag handling issues that can arise, such as those due to a process upset, for example, by undue feed variability. This paper illustrates an extension of the application of this software in examining a large range of NCV operating parameters, such as the %Fe/SiO2 ratio in the slag and the level of minor gangue components in the slag including CaO, Al2O3, ZnO, MgO, and PbO. The conditions influencing the slag liquidus range of NCV slag are discussed with respect to the overall process chemistry.Given that a sufficiently low %Fe/SiO2 ratio is used in NCV slag, most components such as CaO-ZnOPbO- Al2O3-MgO, in small concentration, all contribute to lowering the NCV slag liquidus. Considering the present level of these minor components, the NCV can operate consistently at 1200°C if the %Fe/SiO2 is between 0.6 and 0.8 in the slag. Using the type of phase diagrams presented in this paper, it is possible to develop different Noranda reactor/Noranda converter operating strategies adapted to the feedstocks available at Xstrata mines/plants or from other sources. The NCV is unique in that a fayalite-based slag is employed for high-efficiency continuous converting with excellent operating results."

Jan 1, 2007

By R. J. Gunderman

Explosionproof electrical enclosures for coal mine face equipment have been of the same basic design for many years without significant change. Characteristics for potential improvement were investigated through interviews, visits to mines and studies. Improved safety, health and productivity were the goals. Areas identified for improvement included rapid venting of pressure build-up due to an internal explosion, quick and easy entry or removal of cable entrances, and a quick and easy cover removal for rapid component access. Concepts were identified and evaluated, and the more promising devices were fabricated and tested. Encouraging results from initial tests led to further design refinement and establishment of design guidelines. These design guidelines for a pressure vent and for an elastomeric grommet type cable entry are described along with the testing used. An application for an experimental permit was requested from MSHA. After test and evaluation experimental permit #396 for evaluation in an underground coal mine was granted.

Jan 1, 1980

By Fernando Machuca Pérez

"La minería genera una gran cantidad de desechos de material como lastre, ripios y escorias, que son depositados en un área sin considerar el impacto ambiental que estos producen. En ese sentido, el diseño de escombreras no considera las condiciones ambientales en la industria chilena, y por ello se privilegió el costo mínimo en depositar este lastre sin un diseño que considere esta variable. Por tal motivo, el objetivo general del texto es diseñar los algoritmos de secuencia de llenado de escombreras, considerando las siguientes variables forma, altura, talud y orientación, condiciones meteorológicas y económicas en su diseño, de tal manera que se produzca el menor impacto ambiental por la emisión de material particulado. "

Sep 1, 2015

By Bertha R. Klahold

"In response to numerous inquiries regarding tests and analyses of minerals and related inorganic materials; Bureau of Mines Information Circular 6999, ""Laboratories That Make Fire Assays, Analyses, and Tests on Ores, Minerals, Metals and Other Inorganic Substances,"" by C. W. Davis and M. W. von Bernewitz, was published .in 1938 and revised in 1939 (I. C. 6999R). In this paper on analytical and testing laboratories, the original text has been rewritten and expanded, and a table has been added, in which are listed laboratories prepared to offer a number of special testing services in addition to ordinary assays and chemical analyses. The arrangement of laboratories on, a geographical basis has been maintained.This circular is compiled as a public service, and none of the laboratories listed herein is recommended over any other,These lists were compiled from questionnaires sent to organizations whose work is connected with mineral and metallurgical testing. The response in general was very satisfactory, and the author takes this opportunity to express her appreciation to the officers of the listed laboratories for their cooperation.Acknowledgment is also made of the valuable assistance of the members of the technical staff particularly Morris Slaving/ of the Eastern Experiment Station of the Bureau of Mines at College Park, Md., in the preparation of the questionnaire and technical descriptions.Many mineral samples are sent to government agencies in the National Capital with the request that they be assayed or chemically analyzed. It should be emphasized that there is no place in Washington D. C. where assays and quantitative analyses are made for the public b the Federal Government.Virtually all of the States maintain a bureau of mines, a geological survey, or some similar organization, frequently at the State University, where minerals found by residents of the State will be identified free of charge. Usually, a charge is made for assays. Specific tests, as on clays, are made by some of these offices.The Federal Bureau of Mines, although it attempts to avoid duplication of services rendered by State Bureaus, is always glad to give advice as to prospective markets. It does not compete with private assayers and chemists, but with respect to samples sent to its field laboratories, it does offer to identify them as far as this can be done by inspection and simple optical and chemical tests. This examination is usually sufficient to indicate whether the material has commercial value, or at least if the expense of an assay would be warranted. Except in connection with its own technical investigations, no assays or other special tests are made by the Bureau of Mines.The Federal Geological Survey and the National Museum also make simple tests of specimens as a public service. Neither of these bureaus nor the Bureau of Mines, however, can afford to render such services on long suites of specimens submitted by mineral dealers, well drillers, or others, when such work can be done regularly by commercial concerns."

Oct 1, 1949

By Frank E. Cash, Max S. Petersen

The use of safe equipment, safeguards, and safe practices in the mining and allied industries should reduce injuries and improve accident experience. The object of this report is to give to the mining industry, especially metal mining, a graphic pictorial description of some of the safeguards, equipment, and practices used and followed in the iron-ore mines of the Lake Superior district. Some of the subject material has been in use or has been established for many years, and some is relatively new. Some of the equipment was purchased commercially, and some was designed by the company employees and constructed in the mine shops. The photographs were taken by the personnel of the Health and Safety Division of the United States Bureau of Mines, primarily for use in the Metal-Mine Accident-Prevention Course of the Bureau of Mines. In general, they are arranged under the following headings or subjects: 1. Accident statistics. 2. Support of ground. 3. Hoisting and haulage. 4. Explosives. 5. Fires, gases, and ventilation.

Oct 1, 1948

By E. Steiakakis, A. Athousaki

Nowadays, stakeholders have a strong say to the enforcement of best practices by mining and quarrying companies. In most cases there is a direct relationship between sustainable development principles and best practices. Mining companies try to apply best practices in order to sustain their operation without lost time and effort to litigation, and other obstacles. However, when and where there is a lack of state or regional mineral policy, or when the mineral policy is fragmented and touching on conflicting laws, mining operations may be subject to additional administrative hassles, and, thus, operators feel threatened and tend to apply best practices loosely. This paper argues that the only way that mining and minerals operations can be a source of development is to ensure that they are working within the framework of sustainable development. Furthermore, in order to follow the paradigm of sustainable development they would need to be guided by a regional, national or even transnational (i.e. European) minerals policy.

Jan 1, 2011

By William F. Hahn

This project focused effort on three separate areas: demonstration of a low seam longwall illumination system, design of illumination systems for low coal auger miners, and an assessment of machine lighting systems for machinery used to mine low seam coal. Results indicated illumination systems can be purchased by the mine operators of low coal seams. These systems can be supplied with the equipment as a factory integrated system or can be retrofitted to the machine or longwall equipment.

Jan 1, 1982