Search Documents

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

By R. W. Fountain, J. F. Libsch

ONSIDERABLE time and effort have been ex- pended recently in research designed to provide a better understanding of the solid state transformations leading to the permanent magnet qualities of many commercial alloys. The knowledge derived from these investigations has resulted in the development of new magnetic materials as well as improvements in some of the older materials. The permanent magnet qualities of the newer alloys having high residual inductions and high coercive force values, have been attributed to the precipitation of a second phase or an order-disorder transformation in a solid solution. The ternary Co-Fe-V alloys provide an interesting group of magnetic materials having a wide range of magnetic properties. The low vanadium alloys' possess soft magnetic properties similar to the binary Co-Fe alloys, while at higher vanadium contents (about 10 pct) interesting permanent magnet properties are obtained.2,3 Previous work by Nesbitt' on the ternary Co-Fe-V permanent magnet materials, resulted in the conclusion that the precipitation of a second phase, ?, was responsible for the permanent magnet qualities of these alloys. However, unlike the conventional precipitation hardening alloys, the ? phase, which is stable at high temperatures, is precipitated in the low temperature a phase upon aging. Recent work by Geisler and Martin"." has established that the order-disorder reaction inherent in the binary Co-Fe alloys is also present in the ternary Co-Fe-V alloys. On the basis of their investigation, it was proposed that ordering of the a phase is also a possible explanation of the mechanical and magnetic hardening in these alloys. Thus, it appears that the Co-Fe-V alloys are rather unique in that two solid state transformations are taking place which may account for the properties of these alloys. In view of these facts, the present investigation was undertaken to study the mechanism of mechanical and magnetic hardening in the 10 pct V-Co-Fe alloy with particular reference to the role of the ? phase; and to correlate the results of this study with other magnetic properties. In addition, the influence of increasing vanadium contents on the transformation of Co-Fe alloys was also undertaken to supplement the main objective of the investigation. Experimental Procedure The Co-Fe-V alloys used for study consisted of: 1—a commercial lot of Vicalloy I, a 10 pct V alloy, and 2—alloys prepared by powder metallurgy and containing 52 pct Co and 0 to 14 pct V, balance iron. The commercial alloy was received in the cast and forged condition and was used primarily for the detailed study of hardness, electrical resistivity, and magnetic properties of the 10 pct V alloy. The powder metallurgy alloys were prepared from electrolytic iron, commercial cobalt, and ferro-vanadium powders. The processing cycle was as follows: 1—Elemental powders were weighed and mechanically mixed for 24 hr. 2—Mixed powders were pressed at 60,000 psi into the form of bars 5/8 x 5/8 x 5 in. 3—Bars were sintered in an atmosphere of purified dry hydrogen for 24 hr at temperatures ranging from 1380" to 1340°C, depending upon the vanadium content. The as-sintered bars were cut in half; and one half was machined to 7/16 in. diam for thermal analysis. The remainder of the bar was hot forged to approximately 0.050 in. for X-ray diffraction analysis. Additional details of sample preparation are presented subsequently according to the type of test performed. Thermal Analysis Measurements One of the simplest and most widely used tools for determining phase relations as they change with temperature and composition is to study the rate of change of temperature of a material as heat is supplied or extracted at a constant rate. The thermal analysis method used in this investigation is the inverse-rate method described by Smith.'

Jan 1, 1954

By Vijia K. Karra

The goal of aggregates producing companies across the United States is to ensure their workers go home safely each day. At the National Institute for Occupational Safety and Health (NIOSH), researchers are pursuing this vision of safety and health through a fact-finding approach for reducing injury illness in various mineral sectors. Surveillance data from Mine Safety and Health Administration (MSHA) has been the source for such analyses. It helps to focus research efforts on key machinery, workers, and their tasks. The second installment of this two-part series follows last month's focus on crushed stone.

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending north-easterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 724 per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrothermal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons.

Jan 1, 1955

By Alexander L. Field

In the light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and Egan,l it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550" C., when concentrations of carbon and FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant—a circumstance which might have been predicted from theoretical considerations. At 1550" C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550" C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020 = 2.3 per cent. effective 0.0086 FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930

By William Lodding

Muscovite was the crystalline material used in the experiments discussed in this paper. It was both wet and dry ground for various periods of time. The effects (physical and chemical changes) produced in grinding are analyzed by use of thermal analysis. That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Mackenziel and Bartha2 reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding and, on the other hand, existing strain may be released by the same process, as shown by Holt, et a1.3 All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze, by the use of thermal analysis, some effects produced in grinding. In differential thermal analysis (DTA) one measures the sum of all thermal changes occurring in a substance during heating or cooling; e.g., chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and thermal conductivity, strain release, etc. By thermogravimetric analysis (TGA), on the other hand, only chemical changes involving weight loss or gain are recorded. Similarly, gas evolution analysis (GEA) will register only reactions involving gas evolution. By performing two or all three of these methods of thermal analysis simultaneously and on the same specimen, one can separate the different effects registered and, by difference, evaluate their magnitude. The results of TGA are usually plotted as percent weight against furnace temp. When one differentiates weight against furnace temp, a rate of weight-change curve is obtained, and the resulting differential thermogravimetric (DTG) plots are similar in appearance to DTA thermograms for the same reaction. While the integrated area under a DTA peak represents enthalpy and can be expressed in calories per gram the area under the corresponding DTG peak represents the weight change which took place during a reaction. The similarity of DTA and DTG thermograms obtained from one material can be seen in Figs. 1 and 2. EXPERIMENTAL A Fisher mortar grinder and a porcelain mill with burundum balls were used for both dry and wet grinding. Muscovite was first carefully hand-filed and screened on 20 and 100 mesh. The middle fraction was considered essentially unaltered muscovite.

Jan 1, 1968

By Ferry Belisario Benique

A empresa Aceros Arequipa S.A. no seu complexo siderúrgico situado na cidade de Pisco, no Perú, está reutilizando os finos das pelotas de minério de ferro na fabricação de aglomerados (briquetes) para uso no processo de redução direta em forno rotativo na fabricação de ferro esponja (DRI). Dessa forma, testes no laboratório foram realizados com o objetivo de encontrar um ligante ou mistura de ligantes que proporcione um aglomerado com boa resistência à compressão a frio e boas propriedades mecânicas a quente que garantam sua integridade dentro do forno durante o processo de redução. No presente trabalho apresenta-se a metodologia desenvolvida e os resultados obtidos na fabricação dos briquetes em laboratório e na planta piloto de briquetagem de finos. Adicionalmente, resultados dos briquetes após redução no forno rotativo a escala industrial também são apresentados.

Aug 1, 2018

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009

By L. S. Castleman, H. A. Froot

A study was made of the growth kinetics of B-brass layers in a-brass us y-brass diffusion couples in which both phases were saturated in the 6 phase. It was found that useful estimates can be made of the difhsion coefficients at the ß-phase interfaces from interface displacement data, which are relatively easy to measure experimentally; also, a useful estimate can be made of the mean heat of activation for diffusion from layer growth data. The effects of pressure on layer growth kinetics were explored and found to be consistent with a vacancy model for diffusion in 6 brass in both the disordered and ordered temperature range. 1 HE study of multiphase diffusion receives relatively little attention in comparison with that devoted to diffusion in homogeneous materials. Of the hundred or so papers on diffusion written each year,' only a few are devoted to the subject, and it is the rare review article2,3 that devotes any space to multiphase diffusional phenomena. This is unfortunate, since the metallurgist frequently encounters practical situations involving cementation processes such as cladding, protective coating of metals, and so forth in which he needs guidance of a fundamental nature. The investigation of multiphase diffusion phenomena is complicated by the fact that one must consider reactions at phase interfaces as well as the migration of atoms within the individual phases; these reactions cause the interfaces to be displaced within the diffusion zone. The relative displacement of two adjacent interfaces corresponds to the growth of an intermetallic layer, and it is not difficult to determine experimentally the kinetics of layer growth. In the past few years it has been pointed out4,5 that valuable fundamental information may be gained about diffusion coefficients and the concentrations at interfaces through a study of their motion. Accordingly, it is the purpose of this paper to report the results of an investigation of interface motion in a simple multiphase binary system. In the work reported herein, attention was focussed on the growth of a 6 -brass layer in a diffusion couple prepared from a- and y-brass compositions saturated with respect to the 6 phase. This particular system was chosen for a number of reasons. First, the bcc ß-brass phase is disordered for all compositions at temperatures above 468°C and becomes increasingly long-range ordered for all compositions at temperatures below 454° C;6,7 thus, the effects of a variation in order on interface displacement could be determined. Second, diffusion coefficients have already been obtained as a function of temperature in the ß phase both in the ordered and disordered Re- and a theoretical picture of the mechanism of diffusion in this and other ordered solutions is emerging.11'12 Third, some thermodynamic data are available for the a-, ß-, and ?-brass phases,13,4 and these data could be used to gain insight into questions of phase equilibria and concentrations at phase interfaces.

Jan 1, 1963

By Janine Pierce, Robert Larson, Christine Raasch

The vibration and impact environment for crew members on locomotives has been investigated in a series of studies conducted by Exponent Failure Analysis Associates (Exponent) beginning in 1990. Locomotive cab vibration and impact levels were measured on a variety of locomotive models operating over many different track sections across the Union Pacific, Burlington Northern Santa Fe, CSX, Norfolk Southern, and CONRAIL systems. The comfort and health implications of exposure to the measured locomotive vibration levels were evaluated by comparison with the human vibration exposure boundaries given in the International Standards Organization (ISO) standard 2631-1:1997, the British Standard 6841:1987, European Union (EU) Directive 2002/44/EC, measurements made by Exponent on various commercial and recreational vehicles, and vibration exposure measurement data found in the literature. Methods Initially, vibration levels experienced by locomotive crews were measured and recorded at incremental speeds covering the range of normal train operation. In 2003, a method of measuring the vibration exposure continuously by means of a digital recorder was developed, allowing the vibration level over the entire run or crew shift to be analyzed. For each seating location measured, acceleration was recorded on the seat surface beneath the ischial tuberosities (pelvis) of the seated crew member and on the cab floor directly under the seat. At each of the locations, triaxial accelerometers were used to measure the vibration along the longitudinal, lateral, and vertical axes. Since the vibration environment varies throughout the route, and locomotive vibration levels have been found to be primarily speed dependent, a speed sensor was used to continuously measure the speed of the train. To evaluate the recorded vibrations levels, the data was divided into two-minute segments, which were each processed per the 1997 ISO standard for weighted RMS vibration levels and Vibration Dose Values (VDV). Additionally, PSDs and 1/3 Octave RMS values were calculated to determine the frequency content of the vibration. For each two-minute segment, the average speed of the locomotive was calculated to allow for correlation with the recorded vibration exposure values. The resulting exposure values for the entire run were calculated by combining the data from all of the two-minute segments. Since introducing the continuous method of recording acceleration, 23 seating locations have been recorded on 11 locomotives traveling 11 different routes across various parts of the United States. One of the routes was a shift of ‘yard work’, traveling back and forth in a rail yard coupling train cars together. Results A guide to interpreting weighted acceleration values with respect to health is given in Annex B of the 1997 ISO standard. A health guidance caution zone is defined to indicate the

Jan 6, 2006

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

By Antonio de Ita, Isaias Hilerio, Miguel Barron

"The influence of an unconventional lance with a central nozzle on the multiphase fluid flow in a steelmaking converter is studied in this work by means of computer simulations. The lance has four peripheral supersonic nozzles and a vertical central nozzle. Besides, the oxygen flow in the central nozzle is considered independent from the main oxygen supply. Transient two-dimensional numerical simulations were carried out considering just molten steel and gaseous oxygen as the existing phases. Numerical results show that bath agitation and droplet generation are enhanced as a result of the central nozzle. However, the performance of this lance strongly depends on the distance of the lance tip to the molten steel surface and the velocity of the oxygen jet.IntroductionCurrently, two thirds of the world crude steel is produced through the steelmaking oxygen converter [1]. Given the unquestionable economic importance of this technology, any improvement or optimization proposal is welcome. In the majority of current oxygen converters a top oxygen supersonic jet is blown onto the molten steel through a water-cooled lance to eliminate by oxidation some impurities such as carbon and phosphorus. Conventional lances have inclined peripheral nozzles whose number depends on the converter capacity. During the process, a large amount of gases evolves, forming metal droplets and a metal-slag-gas emulsion [2]. The droplets and the resultant emulsion increase the reaction interfacial area, promoting in this way carbon removal and dephosphorization of the molten steel bath [3]. However, during the blowing stage, the emulsion rises towards the lance and converter mouth and frequently forms layers which accumulate in the lance, reducing the life of the lance tip [4, 5]. It is possible that some freezing of the molten metal occurs due to the low oxygen injection temperature, however there are no reports on this. Besides, frequently undesirable operating phenomena such as spitting and slopping may arise as a result of inappropriate blowing practices or bad lance design. In the oxygen steelmaking industry, novel lances design are needed in order to enhance the decaburization rate and the slag formation and, at the same time, preventing operating practices that decrease productivity and move away the shop from safety standards."

Jan 1, 2012

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surface disposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash."

Jan 1, 1980

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By Tracey Brommer, Britt Elin Gihleengen, Elsa Olivetti, Randolph Kirchain

"Increased demand resulting from the economic and environmental advantages of recycling secondary materials has constrained secondary material supply. As a result of constrained supply, the conventional strategy to maximize recycled content in an individual aluminum alloy must be expanded to maximizing total recycled content in a given production period. This work compares the performance over a two week period of an actual remelter for two strategies; a sequential charge-by-charge optimization framework and an integrated approach that explicitly incorporates the production schedule. Optimizing across the entire two week production is found to increase recycled content and minimize primary and alloying material additions. It is expected that as the scrap material market continues to be constrained by high demand, longer term batch planning strategies that can optimize material allocation will deliver improved performance.IntroductionIntensifying economic and environmental pressure to incorporate secondary aluminum into products is pushing remelters to explore additional strategies and tools to increase recycled content. Aluminum remelters are exploring alternative sources of secondary materials because of constrained secondary material supply and relatively high primary and secondary material cost [1]. Computational models, such as blending models are a tool that could help industrial remelters mitigate supply and cost challenges and thereby increase recycled content. In particular, computational tools can help manage the incorporation of new raw materials of variable quality. Blending models find many industrial applications and have been explored for over sixty years originating with the classic nut-mix problem dating back to 1950’s [2]. Blending models optimize the raw material input to make a desired product subject to a series of constraints such as product specifications and material availability. Deterministic and linear blending model formulations are presently implemented in some industrial aluminum remelters [3]. The primary reluctance of aluminum remelters against computational model implementation is the incapability of their blending models to reflect the intricacy of industrial remelting conditions [4]. For example, to reduce calculation time, industrial aluminum blending models usually optimize a batch plan for a single alloy and are not formulated to optimize several products simultaneously. Since such a model does not include knowledge of subsequent charges in the optimized batch plan, the resulting batch plans tend to deplete the “cleanest” secondary materials leaving the more uncertain and compositionally challenging materials for later charges. As a result, a remelter may override the calculated batch plan or leave certain scrap materials out of the material input to conserve these materials for alternative products scheduled for later production. This work explores an alternative aluminum charge planning tool that can optimize across an extended production schedule and compares it to a heuristic sequential optimization strategy reflecting an industrial remelter."

Jan 1, 2012

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

By G. J. Trezek

The use of polysilicates for treating heavy metals in soils and mining sludges is discussed. Results of the treatment are given for soil contaminated in a metal scrap yard operation and for copper mining processing sludges. The types of metals of concern are arsenic, lead, copper, nickel, cadmium, and zinc. The application of the treatment is predicated on the mixture and relative concentrations of the metals as well as the material matrix. Reductions in soluble concentrations (STLC or TCLP) of one to two orders of magnitude can be achieved with relatively small additions of silicates and cementitious materials.

Jan 1, 1992