Search Documents

By G. Bulut

The aim of this study is to produce desiccant clay from a well known Ca-bentonite deposit in Turkey. Towards this aim, bentonite samples were first procured and then subjected to some characterization tests. Various methods were applied to enhance the moisture adsorption capacity of bentonites to a desirable level. These methods include utilization of some additives namely calcium chloride and heat treatment at various temperatures. It is shown that the moisture adsorption capacity Ca-bentonites without any additive are between 14%~17 % (w/w) upon by heat treatment whereas the addition of calcium chloride significantly, raised the moisture adsorption capacities.

Jan 1, 2014

By F. N. Bender

Percolation leaching of wad-type manganese ores was investigated, using a novel system of alternate upward passage of sulfur dioxide gas through moistened ore and downward percolation of wash solutions to extract solubilized manganese. Bench and large-scale tests designed to simulate vat and heap leaching were made on four wad ores from Arizona and Nevada and on a pailomelane ore from Arizona. Three of the wad ores required prebaking at 500° to 600° C. to produce a permeable agglomerate that would not slake during percolation washing. The hard-type ore and one of the wad ores that contained a large amount of granular gangue did not require prior roasting. The deportment of the different ores toward leaching and percolation was studied with particular reference to the influence of the sulfur dioxide - oxygen ratio and the effect of gas dilution on the rate of manganese dissolution, dithionate formation, and acid production. Crushed charges of the ores, as coarse as 1 inch and as fine as 1/4 inch, were treated for periods of 5 to 11 days. Percolation of the gas and leach solutions through the charges was achieved without difficulty. The manganese extractions varied between 78 and 97 percent and depended upon the size and type of ore leached. The average quantity of sulfur dioxide required in the larger scale tests was about 2.6 pounds per pound of manganese recovered. The dithionate formation varied from 0.35 to 0.9 pound per pound of manganese extracted depending upon the strength of leaching gas.

Jan 1, 1957

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of the cell at temperatures between 800 and 1100 K was measured. While the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03 V were found. It was difficult to determine temperature dependence of the Emf. The Gibbs energy change for the reaction, 113 Li3N (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be !'J.Go, (LiMgN) = -13.2 (±2.9) kJ/mol. Using thermodynamic information on the binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be !'J.Go f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of the stability region of the LiMgN phase. The diagram was found to be in good agreement with the isothermal phase diagram determined by the alloy equilibration method. Although the obtained data includes large uncertainties, the results provide a better understanding of the thermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By John D. Morgan

The United States is the world's most productive nation and its citizens enjoy one of the highest material standards of living of any people in the world. Materials and energy are the lifeblood of any industrialized economy. Annually the United States uses over 4 billion tons of mineral materials and fuels, or 40,000 pounds per person as detailed in Figure 1. Domestic processed materials of mineral origin and energy are valued at more than $150 billion annually, and they are derived largely from domestic sources, supplemented by imports, as detailed in Figure 2. In recent years the superior productivity of the United States has also enabled it to give food and manufactured articles to many other less fortunate nations and peoples of the earth. What then is our concern with materials at this time? Seeing the burgeoning increases in our mineral demand: from 2 billion tons in 1950, to over 4 billion tons today, and projected to 11 billion tons by 2000 - we are getting questions concerning our ability to continue to increase production sufficiently for the future.

Jan 1, 1974

By R. L. Kloberdanz

Compania Minera Disputada de las Condes S.A. (Disputada) is proactively implementing closure and reclamation planning activities at its mining and beneficiation facilities (mining facilities) in Chile where regulations governing mine reclamation are not yet fully in place. These activities are being implemented to improve currently employed measures to protect human health and the environment and to enhance reclamation and facilitate future closure with regard to these areas when mining is completed. As part of this process, Disputada, with the assistance of Shepherd Miller, Inc., developed recommendations and guidelines for future closure and reclamation of the Disputada sites. These recommendations and guidance incorporate planning and operational and post-operational design considerations and practices, and standards used by the mining industry and regulatory agencies around the world. The criteria presented in the guidance are based on achieving conditions that will be suitable for the anticipated post-mining land use. This paper discusses the process and approach taken, and the results.

Jan 1, 1999

By S. M. Graham, G. Mellis

"The determination of the oxidation state(s) of an element present in a solid sample may be required for a number of reasons, including the assessment of the degree of reduction which has taken place during a multi-step production of a metal. In addition, possible flaws in a metal may result from small amounts of oxides included in the solid. The analyte of interest may be present as a major component of a sample of interest, or as a minor impurity - beneficial or requiring removal - in another matrix.Numerous methods have been established for the analysis of species in solution samples - for example, Fe2+ and Fe3+ by titration, Cr6+ by colourimetric means, etc. With appropriate knowledge of the solution being analysed, many of these methods are fairly straightforward, extremely reproducible and accurate. In those instances where the analyte in a solution is known to be in only one form, the analysis is even more straightforward, since it can be achieved instrumentally (by AAS, rCP-OES or rCP-MS, for example).However, the situation with respect to the analysis of solids is not as simple. Various techniques - such as X-ray diffraction - are routinely used by our mineralogists to obtain information about the various minerals present in solid samples, and thus about the oxidation states of the analyte elements present. However, these techniques usually give results that are qualitative, or semi-quantitative at best. They are also usually time-consuming and expensive. One of our colleagues at Mintek, Deshenthree Chetty, has done extensive work in developing a method for the quantification of manganese species in solids using mineralogical methods, and this is no small achievement."

Jan 1, 2014

By T van Niel, M Trefry, B Baker, I Rea, A Hawdon, D McJannet, D Boadle, R Fandrich, A Littleboy

Many open cut mines extend to depths well below the natural water table level with constant dewatering required to maintain operations. When mining activities cease the groundwater starts to fill the void and pit lakes form. The resultant pit lake is directly connected to the surrounding water table and understanding the hydrological and chemical evolution of these lakes is important for minimising environmental impacts. In Western Australia alone there are currently 1800 mine voids and more than 150 mines operating below the water table (Johnson and Wright, 2003). In conjunction with BHP Billiton Iron Ore, CSIRO has been undertaking research to measure and model rates of evaporation from pit lakes in the Pilbara region of Western Australia. Extreme high temperatures and low humidity ensures that this region experiences the highest evaporation rates in Australia.CITATION:McJannet, D, Hawdon, A, Boadle, D, Baker, B, van Neil, T, Littleboy, A, Trefry, M, Rea, I and Fandrich, R, 2016. Measurements and modelling of evaporation from abandoned mine pit lakes, in Proceedings Life-of-Mine 2016 Conference, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By T. Ahokainen, J. Pitkälä, J. L. Xia, A. Jokilaakso, J. Vaamo

"The aim of the present paper is to use the two CFD codes to model the two phase flow in a water model ladle with central gas injection. The codes examined are CFX and Phoenics. An Eulerian two phase model is used and predictions are compared against the experimental data available. The results show that the codes can reasonably well predict the gas-liquid plume in the ladle, and predictions are generally in a good agreement with experimental data. However, differences do exist in predicting the gas volume fraction and velocity profiles. The results should be interpreted most carefully and cautiously, because they are very sensitive to the boundary conditions and dependent on the models for the physical phenomena involved. IntroductionSubmerged gas injection has widely been used in the metallurgical industry for more than a century. At the present, the use of gas is most effective in steelmaking industry where the advantages of the gas injection have already been long well understood. Effective mixing, large contact area between reactants, easy modifications and flexibility of the processes are the most important advantages. Disadvantages include refractory wear, blocking in the tuyeres, and splashing. These disadvantages can be reduced and advantages further improved by studying the flow phenomenon in process vessels. However, it is difficult to study flow in a real vessel because of the high temperatures and physical and mathematical modelling is therefore increasingly used in the process development work."

Jan 1, 1999

By E. V. Konopleva, H. J. McQueen

"The isothermal bainite transformation kinetics of low- and medium-carbon alloy steels after hot deformation and the rmocycling treatment (TC) has been studied by the magneto - metric method. Deformation was produced by rolling at 800°C-1000°C. TC included three cycles of rapid (30°C/s) electro-heating up to 900°C-1000°C followed by quenching.Hot deformation retards bainite transformation in the lower part of bainite range (<400°C) and accelerates it in the upper part (>400°C). The effect is greater for higher strain and lower deformation temperature. Deformation also diminishes the overall bainite fraction below 400°C and increases the completeness of reaction above 400°C.Thermocycling provides more uniform ultrafine austenite grains with average size of 3 µm -4 µm compared to 12 µm -14 µm after conventional heating. The transformation rate after TC was almost the same as after conventional heating in low-carbon steel but was faster in medium-carbon with no change in the completeness of reaction. The degree of acceleration increased with rise of transformation temperature.There are a number of factors which are responsible for a change in bainite transformation kinetics in austenite deformed at high temperatures or subjected to TC. One of the most important factors is the refinement of structure, another one is structural and chemical inhomogenity of austenite due to deformation or to rapid heating. To estimate the contribution of these factors, ?-transformation was studied after different austenitizing conditions (low-temperature heating at 850°C- 950°C; high-temperature heating at 1100°C; step treatment – austenitizing at 1100°C, then cooling to 950°C-850°C). The results obtained make it possible to conclude that the structural and chemical inhomogeneity of austenite activate the bainite reaction while the grain refinement retards it. Intensity of the effect produced by each factor depends strongly on the steel composition."

Jan 1, 1997

By P A. Collier

The general view of the author is that all the good intentions of manufacturers can fail completely if the variations in circumstances in underground mining are not considered at all times. With a belief that it is the customer that has the experience and know ledge of problems which occur on long installations. Reilloc talk with customers in coal mines around the world, and have done so from their inception. With considerable experience in their home market, their technical approach was received with enthusiasm by coal companies in both Australia and South Africa, and whilst experience was obtained in other countries, it is the particularly close working relationship in these two areas that is covered in this paper. The refinement of manufacturing techniques and the fine tuning of the specification to which the chain is made was developed in conjunction with factual underground experience obtained by customers as they sought to improve their productivity and a reduction in working costs. With a reliable product the mines are able to concentrate on improved operational techniques to extend the useful working life and plan for multi-panel usage of the chain.

Jan 5, 1996

By Karl Berger

Today we are talking about Industry 4.0, as the latest revolution of industrial processes and progress, considering that the steam engine (Industry 1.0), railways and cars, mass production in the 1920th (2.0), Industrial Automation (3.0), and finally integrated manufacturing, integrated communication, and internet (4.0) can be seen as the state-of-the-art situation in industry, nowadays. Similar to the Industry progress, we can approach the rolling process of material, which started about 150 years ago in a very basic way. Steam engine- and belt driven-mills were very operators’ intensive, brutal and risky to operate. Mechanical improvements brought throughput, safety and quantity, as also quality of the products. The rolling of steel, in particular of rails, beams, rebar, strip (focus in this paper) and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. From single stands to continuous rolling trains the production and quality of mills increased significantly. From ingots and blooms to slabs, we have to admit a big jump in which has changed the face of the world significantly. Thin Slab Rolling has revolutionized the output and the throughput of rolling mills (Generation 3.0 to 5.0). Finally, Endless Rolling, has boosted the quality and quantity of rolling mill processes and permitted nowadays to enter in market niches which were not thinkable a decade ago. Mastering the automation and applying reliable systems (mechanical and electronically) of drives, actuators and sensors, as also communication and information interchange to all levels of automation are the success factors of such complex mills, we call herein after “Rolling Mills of Generation 6.0”.

Aug 16, 2017

By J. A. L. Henderson

THE potential oil-and gas-bearing area with "which this paper deals is the large undefined Carboniferous basin, roughly triangular in shape, occupying about 10,000 square miles of southern and eastern New Brunswick. Its base, about 135 miles long, lies on the gulf of St. Lawrence and embraces the whole eastern coast-line of the Province, while its apex lies in the south-west corner of the Province, near the International boundary (see map, Figure 1). The Carboniferous basin may be divided roughly into two areas-the Northern basin and the Southern basin-by a structural feature represented by a ridge of low hills running north-easterly from the Saint John river, near Saint John, on the southwest, to Indian mountain, about eight miles north of Moncton, in the northeast. Within the Northern basin, all evidence regarding the presence or attitude of the older Mississippian Albert Shale series, the only oil-bearing rocks known in New Brunswick, is for the greater part obscured by a thick and practically horizontal blanket of Pennsylvanian strata and, although evidences of oil and gas have been reported, none has been positively identified. Five parallellines of gentle folding, running to the northeast, occur in the Pennsylvanian rocks, within a distance of 100 miles from north to south. This folding is reflected in the courses of the rivers, which lie within the synclines. The relationship of the folding in the younger rocks to structures in the uncomfortably underlying older rocks is unknown, but should now be possible of clarification by means of a geophysical survey accompanied by drilling. Independent geological examinations have yielded no evidence of value in this respect, nor have five exploratory boreholes drilled by per-cussion tools to a maximum depth of 3,645 feet been of assistance, as only one inconclusive hole completely traversed the beds which normally overlie the Albert shales.

Jan 1, 1940

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By AIME AIME

FORMATION of a new company through the union of two familiar names in the mining and metallurgical world has just been announced. J. V. N. Dorr and E. L. Oliver have united the businesses and assets of The Dorr Company and Oliver United Filters, Inc., of which they are the respective heads, by the formation of the Dorr-Oliver Corporation under their joint management, and stockholders have approved the merger.

Jan 1, 1931

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961

By B. K. Shibler, K. C. Vincent, W. W. Agey

"INTRODUCTION As a part of the investigation of domestic manganese deposits, examining engineers of the Bureau of Mines collected samples of ore from three from three properties in the general vicinity of Tracy, Calif.The Buckeye mine is 23 miles of Tracy, just inside the northeast boundary of Stanislaus County. The mine is owned by K.O. Winship estate of San Francisco and is leased by Verner Allen, also of San Francisco.The ore is principally manganese carbonate occurring in interbedded layers in white chert, with the original,carbonate mineral altered in place. Four samples, representing four types of ore, were submitted, as follows: A, black oxide; B, pink carbonate; C, gray carbonate.The Wilfred Murphy property (also known as the Murmac claims) is approximately 30 airline miles south of Tracy. The property can be reached by road from either Livermore or Patterson and is on the divide separating Santa Clara and Stanislaua Counties Calif. The ore occurs in lenses along a white-chert formation. A 2-ton sample of ore for testing was taken from a dump accumulated from assessment and development work. The Ladd mine, 13 miles from Tracy in San Joaquin County is owned by Pat J. Connolly of Tracy and is leased by Mack C. Lake of San Francisco. The ore is essentially a chert impregnated with manganese oxides and the association is therefore exceedingly intimate and complex. Samples from each of the three adit levels of the mine were submitted for ore-dressing study.As the samples differed widely in physical character and response to ore-dressing methods of treatment, beneficiation of ores from each property was considered as a separate problem. Hence results of the investigations will be prescribed in separate sections of this report."

Nov 1, 1947

Safety and health at work is about people. It is about people who plan for work, organise work and perform work. It is about those who come in contact with the workplace and those who are responsible for the workplace. There are wider ranging safety and health obligations that are imposed on the industry stakeholders that span all phases of the production process. In all cases, those responsible for discharging the obligations must ask the questions: Is what we propose safe?, can it be done safer? and are we sure? What we learn from recent legal cases before the courts is that it is essential that all stakeholders work together in a collaborative way when discharging these obligations. Safety and health at work cannot become an issue that is viewed only through the eyes of a single stakeholder group. The reason for this is quite simple. The interrelatedness of the responsibilities that are imposed on each of the stakeholder groups, means that the performance based legislation simply wont work, where an active model of communication and consultation is not in place.

Jan 1, 2005

By R. Bonifaz

The Chagres Smelter, part of the Anglo American plc group situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant application of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studying various options for investment suitable for a profitable business of benefits to both Anglo American and Chile as a whole. The most relevant technical indicators are the figures : Energy consumption less than 6,3 GJ/ton fine copper, Intensity of smelting rate in Flash Smelting unit of 6900 ton of copper concentrate/m2 settler of furnace area and be one of the top five smelter in direct cash cost .

Jan 1, 2007