Search Documents

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By C. A. Silva

The kinetics of chlorination of titanium-bearing raw materials has been investigated. For comparison purposes pellets of controlled macro-porosity, made of analytical grade TiO2 and anatase concentrate (Brazil) , have been exposed to different combinations of gas composition - CO, CO2, C12 -, gas flowrate and temperature. A thermogravimetric technique and an adapted grain model have been used in order to assess the influence of the several experimental parameters upon the chlorination behavior.

Jan 1, 1997

By F. R. Morral, E. P. Miller

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By E. P. Miller, F. R. Morral

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By S. A. Bunk, W. P. Wood

In the early 1980's BHP identified several potential gold deposits in West Africa. One of these deposits was located in Mali, near the village of Syama. As a result of extensive explo­ration activities, an oxide ore as well as an underlying sulphide ore was identified. After agreement with the government of Mali was reached the development of the deposit was undertak­en. The plan for the development of the mine included the treat­ment of the oxide ore followed by the treatment of the underly­ing transition and sulphide ore. The development of the deposit was extremely aggressive. Following the approval of the project in early 1989, engineer­ing was started, equipment purchased sitework was started, and the first ore was introduced in December of 1989. This was accomplished in spite of the difficulties of the site. These diffi­culties included: • remote site location without air or road or water access • no existing infrastructure including water, power, or communication • high health risks • limited construction and manufacturing support in West Africa The operation began with a conventional crushing/grind-ing/CIL/elution and electrowinning facility. The facility was designed to treat 2000 metric tonnes of ore per day. After start­up in December of 1989, the operation was improved to the point that plant throughput was averaging nearly 3000 tpd and running at 92 to 93% availability.

Jan 1, 1996

By F. W. Liang

The geology of pearl River estuary belongs in strong weathered rock quaternary geological systen, so the conditions are complication. Since 80's we built the first deepwater wharf of Shenzhen chiwan port which has 3 berths of 10000 dwt, We have built 3 berths for vessels of 40000 dwt both in Shekou Port and Chiwan port. The berths for carriers of 10000 dwt in Yantian Port of Dapeng Bay are constructing now. In the five years, We built more than 20 deepwater berths of 5000 dwt to 40000 dwt. This paper will introduce how to solve the difficulties of the complex geological conditions and how to use the new fashion construction. We will reduce the period of engineering construction and get good quality and make a good beginning of rapid development of port construction in ShenZhen Special Economic Zone.

Jan 1, 1991

By Marston G. Fleming

E. C. Peterson (Anaconda Copper Mining CO., Darwin, Calif.)—A study of this quite comprehensible and interesting paper by Dr. Fleming brings to mind several observations in the practical application of alkalinity and related factors to the actual practice of lead mineral flotation. Soda ash has long been a widely used and a very helpful alkaline conditioning agent in the flotation of galena from the usual run of lead-zinc ores. Soda ash is one of the common "standard" conditioning agents tried in any laboratory investigation of lead-zinc ores because it has so often proved helpful to galena flotation. However, the use of soda ash in the actual flotation of oxidized lead ores is certainly not widespread. In the flotation of certain lead-zinc ores from the Park City district of Utah, it was found in the usual cyanide-zinc sulphate-xanthate circuit that soda ash had an effect of producing a very condensed and flat froth regardless of the many frothers tried and that substitution of lime for soda ash to produce the same pH (8.0 to 8.4) improved the froth condition. However, the flotation of coarse particles of galena became so critical that some would pass through into the tailing, but caustic soda as a substitute for either soda ash or lime produced a very desirable froth condition in the same pH range and greatly improved the metallurgical outcome. Milling was carried out in typically "hard water" from watersheds of limestone and other calcareous rocks and the ore also apparently contributed magnesium and calcium salts to the pulp. Certain lead-zinc ores of Mexico have shown their greatest flotation response in circuits conditioned with sodium bicarbonate, and such actual mill use was also believed to be related to the water necessarily used in milling. On other lead-zinc ores the optimum has been obtained in actual milling treatment by use of caustic soda in both circuits of the operation. In flotation of oxidized lead ores in which sulphidi-zation is employed by addition of sodium sulphide, very high pH's exist in the flotation circuit. With the usual oxide lead ores, demanding 5 to 15 lb of sodium sulphide per ton of ore, pH's in the circuit (closed and open water-circuits) may range from 9.5 to 12, and for ores that contain much anglesite or a high percentage of iron oxide minerals, sodium sulphide consumption may reach as much as 30 lb per ton of ore and the resultant pH will be correspondingly higher. Yet in such flotation treatment employing either xanthate or oil (high-sulphur crude oil or diesel oils) as the collector, satisfactory to excellent grades of concentrate and lead recovery are obtained. Although there have been great studies and accomplishments in the investigations of flotation fundamentals and flotation theory, and although an investigation to determine the effect of all factors entering into the actual plant flotation of sulphide and oxide ores must become very complicated, as Mr. Fleming has mentioned in his caution regarding the drawing of general conclusions for other ores, it seems that it would be of greater interest if the techniques and investigations could, with time, approach the conditions of actual practice and lead the way to improved and more efficient flotation plant performance. Marston G. Fleming (author's reply)—The gulf between fundamental flotation research and plant operation is, perhaps, less wide than Mr. Peterson suggests. For example, the work described in my paper developed from an extensive investigation of a complex lead-vanadium ore from southwest Africa. This investigation started as a standard ore-testing problem but, at almost every stage, results were obtained which could not be interpreted in terms of previous experience. A program of fundamental research was therefore undertaken and was closely interlocked with the ore testing. This coordinated investigation resulted in a flotation process which has now been proved by two years of successful plant operation, and although the grade and mineralogical constitution of ore as well as smelter requirements have altered more than could have been anticipated, our knowledge of the fundamental character of the problem has made it possible to meet each change in conditions with much more confidence than would have been the case had we neglected this aspect of the investigation.

Jan 1, 1954

The phenomena of nature cannot present themselves to any thinking wild without claiming from it some solution. The earth, as it has often been observed, is laid out like a well ordered cabinet, presenting to us, in measure, some means of judging how the laws of nature and the essential properties of matter have worked out all we see before us. "That there have been depositions of strata gradually laid down aud stocked with the remains of the living objects, vegetable and animal, that flourished when they were being imposed, is an universally acknowledged fact. It speaks of a constantly maintained series of operations whereby the globe has been brought to its present condition, and which are ever advancing it to stages that are still before it. That immeasurable ages have been consumed in effecting these developments is also conceded. We witness the very graduated rate of the existing advances and can see that the past action must have been conducted in the same slow deliberate manner. There are many questions, however, upon which inquirers are not agreed, hence they are still within the domains of fair discussion.What has led to those great climatic changes whereby the same portions of the earth have had at various times climates that were glacial, temperate, and tropical? What causes the constant contortions and dislocations of strata and the upheaval and depression of land levels, and that there is a tendency to alternation in the parallel areas undergoing opposite kinds of movement as if the sinking of one area balanced the rIsing of another? What is the reason that the centres of volcanic action are continually shifting, and that the line of greatest activity is always upon the rising areas? That portions of the earth have been subjected to intense alid long continued volcanic action, and again to long periods of repose, and that the periods of activity and repose are·recurrent at long intervals of time? What the mountain chains of the world are in broadly parallel bands? What has caused the stratified rocks to be tilted from their original?

By P B. Hills

This paper discusses the computerisation of the drill hole database, some historical records and the creation of a three-dimensional model of the gold bearing structures for resource estimation and mine design at the Beaconsfield Gold Mine in northern Tasmania. The phase of the work reported here commenced in November 1997 and was completed in March 1998. The historical mining on the Tasmania Reef had reached a depth of 450 m below surface when work ceased in 1914. Production up to this time was 854 000 ounces gold. Recent activity has concentrated on testing depth extensions of the previously mined ore structure, to a depth of 1000 m below surface, and the establishment of an underground mining operation to exploit this resource. The lode structure at Beaconsfield is a typical mesothermal vein style deposit. Gold is contained within narrow quartz, carbonate and minor sulphide reefs or veins. Reef width is variable from a few centimetres to several metres with æsplitsÆ or bifurcations being common. The reef averages 2.7 m true width in the economic zones. The key feature of this style of mineralisation is that reef continuity can be confirmed by drilling to a high level of confidence, but the gold grades are somewhat more erratic in nature. The resource estimates were based entirely on drill data. The drill intercepts on the reef were coded for each split directly into a database and these allocations validated graphically. The distribution of grades and widths show an increasing gold grade with reef width for both the drill hole and historical data. The same histogram patterns, mixed populations and overall arithmetic average grade for the historical mine (at 21.52 g/t > 3 g/t Au) and new drill data (at 21.55 g/t > 3 g/t Au) would indicate that there has been no major change in the overall style or grade of the ore from the historically mined areas to the new resource. The reef, host geology, area of historical workings and resource zones at the Beaconsfield Mine were defined as a series of closed wireframes. The Tasmania Reef was modelled as five mutually exclusive wireframes, one each for the Main Reef, Footwall split, Second footwall split, Third footwall split and Hangingwall split. The data for this exercise was extracted directly from the drill hole database, stored in Microsoft Access format. The formation of the solids was largely automated with manual validation and refinements allowing for multiple runs using different interpolation methods and combinations of drill holes. A rotated 3D-block model in the plane of the Tasmania Reef was created to contain the grade model and allow for tonnage, grade and reef width estimates. An inverse distance squared (ID2) interpolation method was used with ranges of 25 m along strike and 125 m down plunge with blank areas infilled with 50 m by 250 m. Each reef split was filled separately using only drill intercepts from that split. The method was independently validated used MIK methods. Longitudinal sections have been prepared showing gold grade, reef width and width +grade. Estimates were also made for arsenic, sulphur and other minor elements. The long sections show three distinct mining zones. A method is presented for the conversion of the resources to reserves by the addition of mining parameters for minimum mining width, minimum pillar, cut-off grade and internal and external dilution. The selection is done on columns within the block model, and allows for all splits to be considered at once. Multiple runs can be made for varying combinations of parameters to test different mining methods and their impact on reserves, mine life and NPV.

Jan 1, 1999

By Fred P. Dewey

IN preparing material for the exhibit of the National Museum at the New Orleans Exposition in 1881, it was decided to attempt to photograph the interior of a coal-mine, in order to get a strictly truthful representation of a thick coal-seam, and to show incidentally the methods of mining. While we have many drawings, both mechanical and artistic, illustrating the subject, they are not satisfactory for these purposes, simply because they are drawings. Aside from this, much interest attaches to pictures of inaccessible places, and the enlarged copies (30 inches by 40 inches) of the photographs we succeeded in obtaining, have attracted a large amount of attention from the visitors to the Museum. The Kohinoor colliery, Shenandoah City, Pa., was selected as most suitable for the attempt, principally on account of the fine exposure of the Mammoth bed, and the comparatively level character of the workings, in that colliery. This is one of the many anthracite-mines of the Philadelphia and Reading Coal and Iron Company. A detailed section of the fiftyfoot or Mammoth bed in this colliery is as follows: Feet. Inches. 1 0 Clod. 1 7 0 Coal. 1 0 Slate. Top Split. 8 0 Coal. 1 6 Slate divider.* 6 0 Coal. 1 0 6 Slate. 2 6 Coal. 0 5 Slate. 1 8 Coal. 1 2 Charcoal. 5 0 coal. 1 0 Bone and Coal. „ „ Coal. [ Bottom Split. 0 6 Bone and Slate. 3 0 Coal. 0 10 Bone and coal. 1 2 Coal. 0 2 Bone. 4 4 Coal. 0 1 Bone. 0 8 Coal.

Jan 1, 1888

By Someswar Kesh, Gavin J. Faulkner

Introduction Powered supports in longwall mines essentially operate under two conditions: 1. Static (non-working) 2. Dynamic (working) There is a variety of static conditions which may exist in a mine. These may include a temporary stoppage of work for a few minutes or stoppage of work for days because of strikes or lack of demand for coal. Studies on pressure behavior were made during brief stoppages of work (few hours) as well as a long stoppage of work (two weeks). In dynamic conditions, the pressure variation on supports is expected to follow a certain pattern. However, in many cases that does not happen. Pressure-time characteristics of each leg of the supports were studied. This paper discusses the research findings of the studies made on powered support pressure behavior under both static and dynamic conditions. Studies on Pressure Variation in Static Conditions It has been noted (Brenner et a1.,1975) that the pressure distribution on mechanized longwall faces is random in nature and changes with time and position along the face. Figure 1 and Figure 2 show the distribution of support pressures for the front left leg of supports in two different mines. In both the cases it can be seen that the variation of the support pressures along the face is indeed absolutely random. However, the nature of randomness in both the cases is very different. The data in Figure 1 (Mine 1) is much more random than the data in Figure 2 (Mine 2). This can also be seen from the standard deviation of the data (81 26 Pa versus 4000 pa) . By comparing the results of ten other sets of data the same conclusions can be arrived at. Since it was found that in Mine 1, the pressure on support legs was extremely random, batches of ten supports each were taken and the mean pressure plotted. This mean pressure line is shown in Figure 1. It was expected that this would smooth out the variation due to individual props and reveal a better picture of the support pressure distribution. For the case cited, the standard deviation is lowered to 5043 Pa from 8126 Pa which indicates that, on an average, the supports tend to take loads more uniformly, however for individual support legs the load on the supports is very random. The significance of this is that, if the supports are selected on the basis of theoretical load calculations alone (based on the roof block concept or some other concept), only the mean value of the support load required will be known. In the case of a pressure distribution with a high standard deviation, some supports selected on the basis of mean value will fail, while others will be supporting low loads. Hence, for proper selection of support capacity, it is not only necessary to know the average load but also the expected nature of the distribution. The only reason why the supports are supporting the roof in Mine 1 well is the fact that the yield load is above the highest level of load attained. If Mine 2, which has a much higher average load, had the same sort of standard deviation, the loads on the individual legs could easily exceed the support load. For example, if the pressure distribution followed a normal curve and the mean pressure was 36,700 Pa with a standard deviation of 9000 Pa, it is possible that 67% of the supports will be within the pressure range of 36,700 plus or minus 9,000 Pa, or 22,700 and 45,700 Pa. Many of the supports could then exceed the yield load of 40,000 Pa. It is clear then that the mean load is an inadequate criterion for estimating support resistance. The nature of the problem is statistical and such an analysis should therefore be made as far as pressure data are concerned. Statistical Analysis of Pressure Data. In general, in longwall mining and other geo-mechanics studies, it is extremely difficult to specify the exact nature of the distribution of a variable. Under these circumstances, probability

Jan 1, 1986

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978

By S. K. Singh

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By Zamel GI

The utilisation of fossil fuels, including coal (of which Australia is a large producer and exporter) is a significant contributor to the emission of greenhouse gases. Methane gas, formed during the coalification process, is present in coal seams to varying levels depending on the rank and depth of the deposit. This gas usually escapes to the atmosphere during mining operations without prior conversion to C02 or utilisation as fuel. The quantity of methane released can represent from less than one percent to more than five percent of the carbon content of the coal mined. Per unit of carbon, methane has a greenhouse impact many times that of C02. The emission of uncombusted methane to the atmosphere can therefore represent a greenhouse impact of similar porportions to that of the CO2 formed by combusting the mined coal. However, greenhouse emissions from coal can be minimised by collecting the coal seam methane and converting it to water vapour and the less damaging form, CO2. If such conversion is carried out while performing useful work, the methane can further reduce greenhouse emissions by displacing other fossil fuels. Technology has been developed to allow coal seam methane gas to be economically collected in a pure form, uncontaminated with air. This pure methane can be used to supplement natural gas supplies, to generate power or for the production of chemicals or substitute transport fuels. By collecting and utilising coal seam methane, the greenhouse impact from the mining and use of coal can be minimised, with significant reductions possible in the case of gassy deposits.

Jan 1, 1989

By Charlie Monroe

Savage Company History ?C.A. Savage & Son was founded in American Fork, Utah in 1946 by Kenneth Savage and his father. ?Kenneth?s brothers, Neal and Luke joined the company soon after, and remain involved today. ?Since 1988, the company has focused on its strength, expertise in providing high-quality Operating Services & Logistics Management. ?Today, Savage provides comprehensive services in the following Industries: ?Crude Oil Refining ?Sulphur & Fertilizers ?Coal Production and Mining ?Electric Power Production ?Industrial/Chemical Services ?Lumber and Forest Products ?Railroads

Jan 1, 2005

By Charles R. Graig

El Laboratorio de Espectrografía del Departamento de Investigaciones de la Cerro de Pasco Corporation, elaboró un método de control de los circuitos de flotación por espectrografía de rayos - X. El método se basa en el uso de técnicas especiales de preparación de la muestra, los productos del circuito de flotación, y la fusión con pirosulfato de potasio. En este sentido, el objeto del texto radica en describir el procedimiento de la determinación cuantitativa por espectrografía de rayos-X, de las concentraciones de plomo, zinc, cobre y fierro en las cabezas, los concentrados y las colas de los circuitos de flotación. Es importante considerar el diseño del laboratorio de rayos X para la elaboración de los resultados de planta dentro del tiempo especificado. Así, el control de los procesos de flotación permite la rápida obtención de resultados exactos, lo cual hará posible una mejor regulación de los reactivos de flotación añadidos a los circuitos, mejorando el proceso.

Nov 20, 1967

By F. W. Smith

Within the Northern Pennine Orefield, England, intersections of fluorite veins are generally richest in ore, and their recognition enables investigation of the ore potential of the intersecting bodies. A method, based on routine analysis of fluorite for yttrium, has been used with success in mines of the district to predict the location of intersections in partially developed fluorite-bearing ore bodies. This short note is intended as a brief introduction; the details of United Kingdom applications are to be published at a later date. Geology The Northern Pennine Orefield is the second largest fluorspar-producing region in Britain. The associated minerals galena, sphalerite, chalcopyrite, barite, and witherite have all been extensively worked in the past but, with the exception of a single barytes mine, all of these operations are now abandoned. Galena alone is recovered as a byproduct of fluorspar beneficiation. At the present time two companies are producing about 38,000 tpy of fluorspar from high grade vein ore bodies, and a number of concerns are actively prospecting in old lead workings. The mineralization is localized in veins and replacement flats within favorable lithologies in an alternating limestone, sandstone, shale sequence. Since the thickness of individual beds is not great (generally less than 20 m), vein bodies tend to be ribbon-shaped, with length greatly exceeding width and height (Dunham). They thus present difficult exploration targets for conventional diamond drilling techniques. Ore grade varies greatly along the veins, which can change rapidly in character from mineral stained fault gouge to massive mineral bodies up to 10 m in width. It has been known for a very long time that the richer ore bodies tend to be associated with vein intersections in favorable beds. It is assumed that vein fissure intersections provided vertical channelways through which hot ore-bearing brines were able to ascend from deeper cavities in the sequence. Thus investigation of intersections at other horizons generally yields further ore bodies. Technique The relative concentration of yttrium in fluorite is a good indicator, in the North Pennines, of the direction of flow of mineralizing fluids. In all of the ore bodies so far studied in detail in this region, the concentration of yttrium increases markedly in the direction of vein intersections that are believed to have acted as feeder zones to the remainder of the bodies. The reason for this relationship is probably connected with the degradation of soluble rare earths-fluoride complexes by the changes in various physicochemical parameters of the hydrothermal fluids as they entered the ore body cavities from the feeder zones. The simultaneous release of free fluoride ions also contributed to the increased ore values in these intersection zones. Yttrium values in fluorite taken from a longitudinal traverse of the western ore body, Redburn mine, Rookhope, are plotted in [Fig. 1.] The position of a major vein branch and three cross veins are clearly indicated by yttrium maxima. The cross veins themselves contain up to 2.5 m of low grade fluorspar ore. The exact positions of B and C were unknown previous to the geochemical survey. Similar results have been obtained for several other veins and ore bodies in the area. Clean fluorspar was collected as bulk samples from within 300 mm of the vein wall and, since the vein infilling is simple, with mineral growth from the walls inward, analyses of the samples are considered comparable along the length of the ore body. A number of samples taken from the center of the vein show a

Jan 1, 1975

The use of QemSCAN in providing mineralogical input to detailed ore and product characterization has proved of immense value in recent years. In this paper, a brief review of selected Cu-case studies is presented to demonstrate the versatility of automated, quantitative mineralogy by QemSCAN. This versatility ranges from measurement and analysis strategies through to data processing and presentation. As a rapid diagnostic service, it is common to find that only grain size, the degrees of liberation and/or ore mineral modal mineralogy are of interest. By contrast, the detail afforded by the simultaneous determination of both gangue and ore minerals can alert mineral engineers to fatal flaws and attributes deleterious to processing that are directly a function of silicate and other gangue mineralogy. Examples of the latter effects include the influence of micaceous minerals and acid consuming species, while the former include fluorine minerals, which can provide both processing and environmental challenges.

Jan 1, 2007

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 12, 1979