Search Documents

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By Fei Chen, Lesley J. Gaydos, Laurence M. Demers, Douglas C. Kuhn

The fibrogenic effects of silica in experimental animals and humans has been extensively studied (I 7, 20). However, the pathogenesis and molecular mechanisms underlying lung injury and fibrosis resulting from silica exposure remain to be elucidated. It is well-documented that silica can stimulate monocyte-macrophage lineage cells to produce cytokines and growth factors, including interleukin-I (IL- I) (20), tumor necrosis factor-ex (TNF-cx) (I 7), insulin-like growth factor-I (IGF-1) (4), and transforming growth factor-P (TGF-P) (24). Consequently, it has been suggested that the fibrogenic effect of silica may be mediated by cytokines in the fater stages of silicosis. During the early phase of interaction between silica and the pulmonary alveolar macrophage, several direct and indirect lines of evidence suggest that reactive oxygen intermediates (ROI) may play a pivotal role in silica- induced tissue damage (2I, 22). One of the most important components of and contributors to ROI is nitric oxide (NO) produced from L-arginine and molecular oxygen under the catalytic influence of NO synthase (NOS) (I 9). At present, at least three NOS genes have been cloned: a constitutive neuron NOS, a constitutive endothelial cell NOS and an inducible NOS (iNOS) (16). A number of factors have been shown to differentially induce iNOS gene expression in different cell lines including bacterial cell products and foreign antigens. During inflammation, NO is a double-edged sword in terms of the host immune defense mechanisms and the physiologic response to an inflammatory insult. The macrophage is one of the major cellular sources of NO. During the early phase of acute inflammation, NO produced from the macrophage appears to facilitate the clearance of pathogens and promotes a local relaxation effect on the microcirculation of vascular smooth muscle. When the production of NO is left unattenuated, especially under oxidative stress, direct cytotoxic effects of NO can emerge through the formation of peroxynitrite as a result of a reaction between NO and superoxide (2).

Jan 1, 1998

By N. Ahmed

This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size could be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were investigated. The drainage rate of the entrained solids increases with an increase in the degree of hydrophobicity of the floatable particles. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allow gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths.

Jan 1, 2003

By Rodrigo Martins, Mauro Trindade

I Reduction of energy consumption in air compressors by the implementation of individualized load control. Reduction of 3,5% from Jun / 18.

Oct 3, 2019

By J. E. Lawver

On the basis of both laboratory and pilot-scale tests, a newly developed high-tension electrostatic process is technically and economically feasible for the production of iron ore superconcentrates containing 0.02 to 0.20% silica at iron recoveries of 85 to 90%. The process can be used to recover both a superconcentrate and a pellet-grade concentrate, from a feed containing middlings, and the system is not unduly upset from changes in feed structure and composition. The adverse affect of excess quantities of material finer than 30 microns, i.e., above 10% in quantity can be avoided by a desliming step. Finally, because of the cost of drying, the best feed for the process appears to be dry-ground ores as well as spiral, flotation, or magnetic concentrates.

Jan 1, 1970

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

When it comes to structuring major mining contracts, the two most widely adopted formats are æmeasure and valueÆ and æcost-plusÆ. A problem with both of these formats is the difficultly of aligning the objectives of the mining company with those of the contractor to achieve mutually beneficial outcomes. An alternative contractual arrangement is for the mining company to enter into an Alliance arrangement with the contractor, linking remuneration to mine performance across a range of targets. These targets can change over time as operational requirements change.   The aims of this paper are to: +        outline alternative types of mining contracts, as well as their strengths and pitfalls; +        describe the philosophy behind the Alliance contract at Newmont Waihi GoldÆs Favona underground mine; and +        identify some of the keys to success and pitfalls to avoid when implementing an Alliance.

Jan 1, 2007

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By R Shrimali, P Rajmeny, L Shekhawat, A Joshi

Rampura Agucha open pit mine has successfully been excavated to a depth of 320 m, incorporating multistage working. The key to success is the implementation of presplitting as control blast measures at every stage of mining, including intermediate cut backs, in addition to the final wall. The major challenges encountered in establishing presplitting in the hang wall as compared to the footwall of the mine are:reversely dipping foliation, ie dipping into the hang wall itselfstriking obliquely at an angle of 20–30° with regards to the general strike of the pit wallthe presence of numerous geological planes of weaknesses like major faults, slips, etc.Control blast parameters like hole inclination, spacing and stand-off with buffer row were chosen initially from the literature survey and were subsequently fine-tuned by field trials to the mine geo-mining conditions of the hang wall. Electronic initiation used for trim blasts along with double presplitting in fault-affected zones helped in getting better presplit performance and resultant stability of the hang wall.CITATION:Rajmeny, P, Shrimali, R, Shekhawat, L and Joshi, A, 2015. Establishing the design parameters of a control blast for long-term stability of the hang wall at Rampura Agucha Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Syd S. Peng

Coal mine ground control is the science of the application of rock mechanics principles to coal mining operations. More acceptance of ground control techniques by the US coal mining industry has been seen in the 1980s. It has been demonstrated many times that a proper ground control design is key to a successful coal mining operation. However, numerous in-mine applications of various ground control techniques by the author indicate that cur¬rent techniques need improvement. The biggest problem in coal mine ground control is that miners are dealing with materials of rapidly varying properties and occurrence. And only the exposed surface can be identified positively. Thus, in attempting to solve the ground control problems, many unknown factors are assumed. Some of these problems deriving from such assumptions are discussed here. Coal pillars There are two types of coal pillars - barrier and chain pillars - depending on the purpose. Barrier pillars are those located between panels or sections or mines. Their objective is to isolate the mined-out effects of one from the other. Chain pillars are characteristic of room-and-pillar mining. They are designed to support the overburden load and protect the surrounding entries and crosscuts. Pillar design is the most popular and, frequently, the only ground control technique employed by coal operators for mine design. There are many pillar design formulae available (Bieniawski, 1983; Peng, 1986). Nearly all consider both size and width/height effects. Specifically, pillar strength decreases with increases in pillar size and increases with increase in the ratio of width to height. However, the manner of those changes varies with investigators. Consequently, the pillar size determined varies considerably from investigator to investigator. And the variation grows much more pronounced as the seam depth increases (Fig. 1). The question, then, is which one should be used? One may say each formula is developed for a particular coalfield. A particular formula may have been used to design a pillar, which has not failed. Does that mean it was over designed? Not necessarily, because no one can confirm its stated "safety factor." Recent case studies (Peng, 1986; Tang and Peng, 1988) show that all pillar formulae are too conservative for chain pillar design in room-and-pillar mines due to the following two problems: • Uncertainty about in situ pillar strength. All formulae employ uniaxial compressive strength of selected samples tested in the laboratory and scaled to that for underground pillars. The scaling factors are not well proven. In situ testings by Bieniawski (1969) suggested that 1.5 m (5 ft) pillars are representative of in situ pillars that, after being tested in various US coal mines, are not universally applicable. • Uncertainty about the actual loading on the pillar. The most frequently used tributary loading theory defines the loading as total overburden weight tributary to each pillar (from roofline to surface). This is too conservative when it applies to coal measure rocks. The overburden consists of layered strata of different stiffness. Many stiffer strata will self-support over small roof spans. Depending on the location of these strata above the coal seam, it will reduce pillar loading in various proportions. It follows that total structural analysis using, for instance, finite element method is more appropriate. It can take into account the interaction of roof and floor strata with coal. This has been demonstrated by Peng et al. (1986,1988) on several case studies. However, the validity of the finite element structural analysis depends on the accuracy of in

Jan 1, 1989

By D. B. Kibler

Pill Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County this area is approximately 100 miles long and varies from 2 to 30 miles 1n width Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon Marion County, in the year 1888, by Albertus Voight who lived within a few hundred yards of the spring Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County Phosphate was found in many places as "outcrops " Looking for outcrops was the first method used by the early prospectors in searching for deposits Several years passed before any systematic method of prospecting was used EARLY MINING The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from 1/2 to 1-yd capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907 From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers At some places, the overburden was loaded into side-du nip skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine The maximum depth of overburden that could be economically removed by hand labor mules and scrapers was approximately 15 feet About 1905 one of the companies erected a producer-gas powerhouse near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden From the year 1888 through the year 1939, approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for the export trade Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today only three companies are operating These

Jan 1, 1941

By A. F. Deng

A general description of the project, mainly the pier foundation design of the ZHU JIANG FANYING is presented in the paper. The major contents include the foundation scheme, the evaluation of bed-rock characteristics, the allowable bearing pressure, the design and construction of pier foundation.

Jan 1, 2010

By Chris Roper

The Gavia Autonomous Underwater Vehicle is a two-man portable AUV that is capable of performing seafloor surveys in water depths to 2000 meters. The standard survey sensor suite includes a dual frequency side scan sonar and high resolution digital camera. Additional survey sensors are currently being incorporated into the Gavia AUV, include Sub Bottom sonar, Swath Bathymetry sonar and Multi Beam sonar. The modular design of the Gavia AUV allows the end user to quickly incorporate new sensors including client developed propriety sensors.

Jan 1, 2005

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Mousa Mohammadi

Due to operational advantage of dragline in simultaneous excavation and back-filling, the equipment has gained vast importance in open-pit mining. Besides, absence of auxiliary haulage units and a myriad of other benefits are also credited in favor of excavation of muck piles by the draglines. However, the aspects of production, productivity and economics are of utmost significance in dragline operation and planning. In this light, the present paper is an endeavor to analyze availability and utilization of dragline operations. The paper presents a good amount of data for 4-draglines operating in one of the major opencast projects in India. The study reveals the trends of availability and utilization of these draglines during last 11-years. Furthermore, the study also highlights the salient reasons for loss of available hours and for idling of the draglines. Some startling information and facts have been illustrated in form of graphs and pie charts.

Aug 1, 2013

By J. Mastoris

The problem of defining the optimum final limits of an open pit mine has challenged the mining industry for the last three decades, mainly due to the great number of variables involved and the sheer computational effort required in real life applications. An actual lignite deposit is used in this study in order to introduce and apply a methodology to be used as a basis for surface mine design optimization. A geologic reserves model of the deposit is first developed with the use of an integrated geostatistical modeling package. The model is transformed into an economic one through the use of flexible objective function formulation(s). The optimization of the final open pit limits is then enabled with the use of a competent, commercial optimizer, and comparative sensitivity analyses are performed in order to study the effect of some basic mining and economic parameters on the optimal pit design. The conclusions drawn can develop useful guidelines for decision making by the mine operator.

Jan 1, 1995

By Don U. Deere

The tunnel boring machine (TBM) can be a magnificent tunneling device under optimal rock conditions. Such ideal conditions would include good Rock Material Characteristics (compact, uniform; low to medium strength, hardness, and abrasiveness); good Rock Mass Characteristics (few joints and shears; unweathered); and good Geologic Environmental Characteristics (above groundwater level and moderate in-situ stress). Such idealized rock conditions would eliminate support problems, fallout at face and grippers, frequent cutter changes, and water problems. Daily advance rates of 50 m would be commonplace. Unfortunately, nature seldom provides the ideal geologic characteristics. The challenge to the geologist, machine manufacturer, and contractor is to provide equipment and procedures to best handle the adverse geologic features, once identified.

Jan 1, 1981

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

Variety among deserts is nearly as great as among other climatic environments. Common to most deserts, and to areas downwind from them, is the dominance of aeolian transport of surface material, at least during some seasons of the year. The result is dilution of local surface materials with varying proportions of chemically uniform fine sand and silt, often imported by the wind from remote areas. Fortunately, desert pavement,.even though separated from bedrock by a meter or more of nearly pure loess, is simply a diluted reflection of nearby bedrock. Infiltration of loess through the surface debris and the rudimentary soil-forming processes in the desert usually preserve the integrity of the pavement. This pavement, or its "downstream" derivatives, provides a suitable sample for exploration geochemistry if proper care is taken to circumvent the aeolian dilution. The simplest and most commonly used method of circumventing the dilution is to use a coarse fraction of soils or stream sediments, discarding or retaining the finer fraction depending upon the magnitude of the dilution. Where the coarse surface debris is composed of rock chips representative of the bedrock sources, the method is successful. Under most circumstances the coarse fraction of the surface material will give a fair representation of gross lithology and will occasionally give an indication of mineral- ization. The major drawback to this approach is that selective weathering and erosion in the vicinity of mineral deposits often lead to the loss of ore minerals into the finer fraction, leaving a coarse residue enriched in feldspar and particularly in quartz; thus, the geochemical signature from a mineral deposit is effectively reduced or completely masked. The second most commonly used method to overcome aeolian dilution, and probably the most effective at present, is to use a heavy- mineral concentrate. This approach presupposes that the chemical signature sought resides in a heavy mineral. Fortunately, the arid weathering cycle is conducive to the formation of a wide variety of secondary ore

Jan 1, 1988

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014