Search Documents

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

The total estimated production of coal in the United States during the first century and a quarter of mining is shown in Table 20. This is the total of the production of the various states already shown in the various tables, and is believed to be the first statement of this sort made. No such table prepared from limited data can be accurate, but it is the writer's opinion that the totals shown are less than those actually produced. It was thought that this study would enable a reasonably accurate account of the movement of coal down the Ohio and Mississippi Rivers to be written. The searches made have shown that at this time the data do not exist from which such a study can be made, but some of the facts collected may be useful to future students.

Jan 1, 1942

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

An intensely sheared and mineralized zone occurs in the quartz dolerite greenstone (or younger greenstone) mass on the western limb of the Kalgoorlie syncline. This zone comprises the western part of the Golden Mile and has produced the greater part of the 33,000,000 oz of gold produced to date from the main mining belts. A study of the general geological and structural features suggests that the lode shear system will continue southward on a pitch similar to that of the main syncline. Although payable ore has been found recently further to the south, the expectation of large quantities extending southward from the present mining areas is problematical.INTRODUCTIONUntil the late 1930's the principal mining activities in the western lode system were centred on three major ore-shoots formed on the No. 4, No. 3 and to a lesser extent on the No. 2 lode shears (Fig. 1). With the gradual reduction of grade in depth on these main ore shoots, increasing attention was paid to the "Minor Lode" system of lode shears known to exist in the same area. A large quantity of payable ore was found on these "Minor Lodes" particularly in the central part of the mining area. In recent years more attention has been given to exploration in a southerly direction.ROCK TYPES AND STRUCTURESThe western system occurs on the western flank of a dragfolded, south pitching syncline. The rock succession consists of Black Flag sediments overlying the younger greenstone horizon which overlies the fine grained older greenstone horizon. The axis of the syncline is regarded as a tight infold of the overlying Black Flag sediments. This infold has been faulted and intruded by albite porphyry resulting in the formation of a composite body of slates...

Jan 1, 1964

By M. Yavuz

Multiple Criteria Decision Making (MCDM) is one of the most considerable branches of Operation Research. MCDM refers to making decisions in the presence of multiple, usually conflicting, criteria. The problems in MCDM are classified into two categories: Multiple Attribute Decision Making (MADM) and Multiple Objective Decision Making (MODM). However, very often the terms MADM and MCDM are used to mean the same class of models and mostly confused in practice. Usually, MADM is used when the model cannot state in mathematical equations and otherwise MODM is used (Hwang and Yoon, 1980). Decision-making (DM) is extremely important stage in Mining Engineering like other engineering branches. Every mining engineer makes several decisions in daily mining applications. Most of the decisions made by mining engineers are completely instinctive according to their past experiences and there is not any DM method applied in DM process. Analytic Hierarchy Process (AHP) is one of the well-known techniques solving the decision problems. The AHP is very simple, and understandable method especially non-numerical data considered in DM process. Equipment selection is one of the prominent problems of mining engineering. Mining engineers have to make difficult decisions when equipment selection stage. As the decisions in the equipment selection have radically influenced the economic life of any mining scenario, these are considered as complex MADM problem. So, the decision maker can evaluate the subjective criteria in the problem of equipment selection. The decision maker wants to maximize more than one objective criterion for equipment selection stage. Among the number of alternatives, the most suitable equipment must be selected according to objectives and alternatives. MADM applications can help the decision maker to reach the optimal solution for the equipment selection. In the mining industry, MADM methods can be applied for the equipment selection because it is a process that includes subjective and objective criteria affecting the selection of equipment among the alternatives.

Jan 1, 2007

By E. I. Robinsky

"In light of the recurring spills and failures of conventional tailings disposal pond dams, a brief review of the Thickened Tailings Disposal (TTD) system is presented. It is shown that by the process of thickening the tailings to a heavy slurry prior to disposal, it is possible to create a self-supporting deposit of tailings and to eliminate the typical superimposed settling pond. These features, together with the ability to reclaim the disposal area even as mining continues, preclude an ecological disaster. IntroductionMine tailings spills are really not such rare occurrences. They have been happening on many continents, in many countries. Neither Canada nor the United States have been spared. In Ontario, the most recent spill occurred at a closed-down tailings disposal area in Matachewan, in 1991.Such continuing disasters could be avoided if a different approach were taken to the disposal of tailings wastes. The recent failures at the Los Frailes mine in Spain, the Omai mine in Guyana, and the Marcopper mine in the Philippines, will hopefully shake up the industry to consider other methods of disposal. The reason why the failure of a conventional tailings disposal dam is so environmentally disastrous is not the dam itself, but the fact that the dam retains a mass of very loose unconsolidated tailings and a great deal of water, or process fluid1. If the dam fails, the contents liquefy completely as they flow through the breach. In this liquid state, they can flow many miles downstream. If the dam itself were built of tailings material, as is often the case, it too would liquefy and join the flow.The reason the material is so loose in the first place is that it has been discharged into a pond filled with water. The tailings particles drift down through the water, their weight reduced by 50% due to buoyancy, to form a loose structure, like a “house of cards,” or lakebottom mud. It doesn’t take much of a shock to collapse the material into a liquefied state."

Jan 1, 1999

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By Pradeep K. Rohatgi, Clyde M. Adams

Structures produced upon solidification of the eu-tectic composition (33 wt pct Cu) aluminum copper alloy have been examined as a function of freezing rate dfs /d? , the rate of change of fraction solid (fs) with time (8). Slow (dfs/d? = 0.0016 sec-1), intermediate (dfs/d? = 0.02 sec-1) and rapid (dfs/d? = 0.4 to 7.30 sec-1) freezing rates were used. The lamellar Al-Cual2 eutectic is arranged in the form of rod-shaped colonies at rapid freezing rates. The colonies are aligned parallel to the direction of heat flow, whereas the lamellae within the colonies are aligned at various angles, as high as 90 deg, to the direction of heat flow. The colony spacing (C) is proportional to the square root of inverse freezihg rate. The relationship is C = 15.5(dfs/d?)-1/2 where C is in µ and 8 is in sec. The ratio of colony spacing to lamellar spacing is greater than 20.0 and increases with a decrease in the freezing rate. A duplex dendritic structure is produced at intermediate freezing rates. A fine lamellar eutectic is arranged within the dendrites (exhibiting side branches at an angle close to 60 deg from the main stem) and a coarse irregular eutectic appears in the interdendritic regions. The duplex eutectic structure is also produced at slow freezing rates. However, at slow freezing rates there is a Platelat of CuAl2, along the center of the main stem of each dendrite and the other lamellae are arranged perpendicular to the central platelet. THE eutectic between CuA12 and a! aluminum has been reported to freeze in a lamellar form by several workers.'-3 chadwick4 has measured the interlamel-lar spacing as a function of growth rate. Kraft and Albright2 have reported on irregularities in the lamellar structures, and have proposed growth models which account for the formation of faults during solidification. In certain instances the lamellar eutectic has been found to exist in colonies. The colony formation315 has been attributed to the breakdown of a planar liquid-solid interface due to rejection of impurities. The aim of the present work is to study the structures produced from the eutectic aluminum-copper alloy under relatively fast solidification rates, such as encountered in casting and welding operations. The solid-liquid interface presumably remains planar under conditions of slow unidirectional freezing which produce lamellae aligned parallel to the direction of heat flow. The local growth velocities are the same over the entire interface and are equal to the rate of growth of the all-solid region. The spacing between the eutectic lamellae is inversely proportional to the square root of the growth rate of the all-solid region. Under the freezing conditions used in the present study, the solid-liquid interface is cellular or dendritic and the local growth velocities are different in the different regions of the interface. The relationship between the growth rate of the all solid region and the local growth velocities varies with the location and the shape of the interface. The growth rate of the all-solid region is, therefore, an inadequate parameter to describe the eutectic micro-structures which depend upon the local growth velocities. For this reason the structures have been examined as a function of freezing rate, dfs/d?, where fs is the fraction solidified at time 0. The freezing rate was varied by a factor of 4000. The relationship between the freezing rate, dfs/d?, and the growth velocit of the all solid region depends upon the specimen geometry and the shape of the interface. EXPERIMENTAL PROCEDURES The A1-33 pct Cu alloy used throughout this study was made in an induction furnace, using electrolytic copper and aluminum of commercial purity (99.7 pct), the primary impurities being silicon (0.12 pct), iron (0.14 pct), and zinc (0.02 pct). Three ranges of freezing rates were investigated: 1) A spectrum of rapid freezing rates (ranging from 0.40 to 7.30 sec-1) was obtained in arc deposits made on 2-in. thick cast plates of the eutectic alloy. The arc was operated at constant power and was made to travel at constant velocity on the surface of the plate that was in contact with the chill surface during solidification. The pool of liquid metal formed under the moving tungsten arc solidified rapidly by heat extraction through the unmelted plate. Conditions of unidirectional heat flow were achieved near the fusion zone interface, especially in the center of the arc deposits. The great advantage of the arc technique is that rapid cooling and freezing rates can be varied in a qualitative way. The correlation between the arc parameters and the solidification rate is given by the following relationship:6-8

Jan 1, 1970

By Dalton Fowler

"Pressure vessels used in pressure leaching and pressure oxidation processes in the mining industry are often lined with acid resistant brick and membrane systems. Although the options available when it comes to selecting materials and linings designs for these vessels appear somewhat limited there are, nevertheless? several choices which must be made in order to successfully design, manufacture and construct these linings. These choices require careful evaluation of materials properties which include, among others, thermal conductivity, thermal expansion, chemical swell, and modulus of elasticity, as well as a variety of construction methods.Some of the options available, and some of the means of evaluating them objective of this discussion."

Jan 1, 1999

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.' Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962

By Leonard Logan

Production control in the petroleum industry may be discussed under three general heads: engineering, legal, and economic. Though the problems that fall under the respective heads of engineering, law, and economics are separate, they are dependent and interrelated. The present study will deal with the economic phases of production control and only incidentally with the legal phases as they affect the economics of the problem. No one of these forms of control is more important than the others. The engineers have performed their service well, and although there are many problems of engineering control yet to be solved, they are not pressing. Legal control is a problem for the legislatures and the courts to solve. The petroleum industry is such a comparatively young industry and the legal problems are of such recent origin that the courts have not yet been called on to settle all the issues and the legislatures still have before them bills concerned with the regulation of the industry. Economic control of production in the petroleum industry is a highly desirable goal but it has not yet been completely achieved. Since the first commercial well was drilled in 1859, there have been recurring periods of overproduction. (Over- production will be used here to describe a condition wherein so much crude oil is available that a satisfactory and reasonable price is not received for the product.) The production of oil in 1859 approximated only 2000 barrels. In the following year production jumped to 500,000 barrels, thus bringing into

Jan 1, 1932

By L. L. Hirst

Liquid fuel oils possess certain advantages over solid fuels. Ease in handling, precision temperature control, and almost complete freedom from ash are among those considered when a liquid fuel is selected for use in industrial processing. In some instances these fuels are desirable because more heating units can e packed in a Given space where space is limited, as on snips. In other cases the' are chosen because of lower actual cost per British thermal unit absorbed, or for control of the flame to increase the capacity of furnaces, as in steel and refining.

Jan 1, 1948

By H. F. Easter

(San Francisco Meeting, September, 1915) THE lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly oil a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been clue partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lead or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted heady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. This matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is clone by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 8, 1915

By K. Johnson, B. Schiffer

Demonstrating aquifer restoration is an essential component of regulatory approval needed to mine uranium, copper, and other minerals by in-situ recovery (ISR). A PHREEQC geochemical model provided a useful means of forecasting the time for restoration and predicting future groundwater quality following low pH mining at Strata Energy’s Ross ISR Project in northeast Wyoming. The model simulated groundwater quality at three phases of the process: at the end of mining; during restoration; and post- restoration. The model utilized the one-dimensional reactive transport and dual porosity features of PHREEQC. Mineral surface ion-exchange, dissolution/precipitation reactions, and adsorption processes were simulated to estimate water quality as the pH was shifted from circumneutral to acidic during mining and back to neutral during restoration. The model results showed that cost-effective management of mine water could meet regulatory requirements. Additionally, the model was used to interpret results from a field trial and inform operational decisions. The predictive approach and geochemical understanding developed have application in assessing aquifer restoration for other ISR projects.

Mar 2, 2022

By Thomas W. Smelser

A full-scale geotechnical model of a 15-foot (4.6 m) wide coal mine entry in correlation with computer finite-element analysis (FEA) is being employed at the Bureau of Mines Spokane Research Center for basic research on roof-bolt support systems. Physical and computer modeling of various coal mine roof-bolt reinforcement systems will increase our basic knowledge of how roof supports function. This information, in correlation with computer FEA and underground verification tests, will provide a basis for establishing safer, more cost- effective roof control plans and help establish guidelines for employing fully grouted and conventional bolting systems. The basic rationale for the research, research approach, methods and equipment employed, results to date, and future research plans are described in this paper.

Jan 1, 1982

By Bart Bartholomew, Randall J. Essex

INTRODUCTION In June of 2004, at the North American Tunneling Conference in Atlanta, an all-day workshop was conducted to review the application of Geotechnical Baseline Reports (GBRs) for underground construction. The moderator for the program was Bart Bartholomew, former President of Fruin Colnon Construction Company. The program involved commentary by a panel of engineers, owners, contractors, and legal representatives within the North American tunneling industry, as well as an extended audience discussion. The panelists were: Peter Douglass, President, Peter Douglass, Inc. Randall Essex, Executive Vice President, Hatch Mott MacDonald Joseph Gildner, Deputy Director for Technical Services, Sound Transit Randall Hafer, Esq., Kilpatrick Stockton Robert Fitzgerald Esq., Watt, Tieder, Hoffer, & Fitzgerald Kirk Samuelson, Senior Vice President, Kiewit Construction Group DEVELOPMENT OF PROGRAM FORMAT The focus of the program was to assess the state of the practice in the preparation of GBRs, and to discuss improvements that could and should be made with regard to their preparation, interpretation, and application. The approach used to achieve this focus in the broadest possible way was unique, in that it involved the panelists’ preparation of the workshop format and materials months before the presentation of the workshop. First, each of the six panelists was selected by the moderator based on their reputation and involvement in their respective fields of expertise, taking care to maintain balance and contrast within the collective pool of talent assembled. Following selection and agreement to serve on the panel, each panelist was asked to independently submit to the moderator a list of the six most pressing issues involving GBRs that they each frequently encountered in their individual professional experience. Each was asked to rank their issues in descending order of perceived importance. This process resulting in a pool of thirty-six potential or “candidate” issues for use in the workshop program. Contrary to the moderator’s expectations, there was surprisingly little duplication among the thirty-six issues submitted.

Jan 1, 2005

Over half of the molten aluminium produced at the 52,000 tons/ year eapacity plant operated by Comalco Aluminium (Bell Bay) Limited in Tasmania is cast into saleable produets by the direct chill process. Considering the importance of direct chill casting to the aluminium industry it is surprising that so little published literature on the subject is available, although Easton (1947), Smart (1954), and Uppert (1940, 1944, 1945) have contributed much toward lifting the veil of secrecy surrounding the process.The direct chill, or D.C. process as it is commonly called when related to aluminium, consists basically of feeding molten aluminium or its alloys into; water-cooled mould from the bottom of which solid aluminium is continuously extracted. Although the casting procedure is continuous in principle, the equipment is normally operated in an intermittent manner. Castings up to 20 ft long are formed during a cycle. At the end of the cycle casting is stopped and the pit into which thc castings are dropped is cleared before a new cycle commences. Depending on the size of the casting in relation to the cross sectional area of the pit and the support mechanism (commonly a hydraulic ram), 'drops' of up to 15 tons are not uncommon. This method of D.C. casting IS termed vertical D.C. casting and is the one most commonly employed in the aluminium industry.Horizontal casting has come more to the fore in recent years with the casting being extracted from the mould in the horizontal plane and is a truly continuous casting method since flying saws can be simply used to cut the continuously cast shape into required lengths as it emerges from the mould...

Jan 1, 1967

By P. van Meurs, C. van der Poel

From observations of the linear displacement of oil by water from a porous medium as visualized in transparent models, new insight into the mechanism of vircous fingering, as occurring in the case of unfavorable oil-water viscosity ratios, has been obtained. A mathematical description of the observed phenomena leads to formulas. expressing both oil production and pressure drop across the formation as a func-tion of cumulative water injection with the oil-water viscosity ratio as a parameter. Theoretical results are compared with those obtained from scaled laboratory experiments in sand-filled rubes in which water was injected at the one end and production was obtained from the other end. In the second part of the paper the same principles are used to calculate a more realistic production scheme in which production of oil and water is obtained from wells regularly distributed over the field. Results show satisfactory agreement with production data of an actual oil field. Application of the theory is extremely simple as only a limited number of readily available parameters have to be known and results are presented in an analytical form. INTRODUCTION When oil is displaced from a porous medium by water having a viscosity lower than the oil. the oil-water interface is essentially unstable and has the tendency to break up into what are called "fingers" or "streamers". This Viscous fingering has been noted before by Engelberts and Klinkenberg' and has recently been demonstrated in transparent models by van Meurs-. It is highly questionable whether it is at all possible to perform relative permeability measurements In the laboratory reproducing the same distribution of water and oil in the cores as Present in practice. Therefore, we based our descriptive theory on an idealized model which was "tailored" to the fingering mechanism as observed in transparent models under scaled conditions. This approach was the more attractive, as a highly simplified model had already yielded an adequate description of the process. Though we are aware our theoretical approach can be extended in several ways, it is given here in its simplest form to explain the fundamental principles and to avoid complicated formulas. SIMPLEST CASE OF A LINEAR DRIVE Observations and Theoretical Model In Fig. 1 a series of photographs shows how water penetrates into a formation saturated with an oil which is considerably more viscous than the water. The technique for obtaining these photographs, using transparent models, has already been described?. The fingers can be clearly observed and are seen to be mainly parallel to the flow direction. Note that the contours of these fingers are not smooth but show protrusions of water enclosing oil pockets.