Search Documents

By Ellsworth Daggett

THE system of pitwork used with the Cornish pumping engine, and which, for want of a better name, we may call the Cornish system of pitwork, consists essentially of a series of plunger-pumps, situated one below the other, in a shaft or incline, the plungers being operated by a rod called the pitman or pump-rod, which must, therefore, extend from the motor at the surface to the lowest pump. The subject will be best understood by reference to Fig. 1, in which k may be taken as typical of the ordinary plunger-pump, in which S is the suction pipe, u, the lower valve situated in the H piece T; v, the upper valve situated in the valve-box O; I, the mounting-pipe or column through which the water is carried to the surface; L, the plunger-barrel, and P, the plunger working through the stuffing-box, and actuated by the branch rod r, which is attached to the main pump-rod, R. The action of the pump is as follows : On the ascent of the plunger, acting now by suction, the water flows from the reservoir through the valve u, into the barrel, L. On the descent of the plunger, the water is forced up through the valve, v, which acts merely as a check valve, into the pipe, I, through which it is, at each successive down-stroke of the plunger, forced upward until it reaches the next reservoir, from which it is taken by another similar pump, and so on until it reaches the surface or drain-tunnel. The pump is obviously only single-acting, i. e., it acts only during one-half of its entire stroke. The weight of water raised during the up-stroke of the plunger is equal to the weight of a column of water whose base is the area of the plunger and whose height is the mean distance between the plunger-face and the surface of water in the lower reservoir, a distance not usually exceeding 12 or 15 feet, and which obviously cannot under the most favorable circumstances, exceed 25 or 30 feet. The water forced up during the down-stroke is equal to the weight of a column of water whose base equals the area of the plunger and whose height equals the length of the mounting column above the mean position of the plunger-face, say from 150 to 300 feet. Almost all of the useful work, therefore, is done on the de-

Jan 1, 1879

By Diana Méndez, Mario Huapaya, Alejandra Manrique

El proyecto de RIMAY en Cajamarca ha constituido, en el 2022, un espacio de articulación público-privada para la implementación conjunta de iniciativas para el desarrollo en la región. Ello, resultado del compromiso y constancia de un grupo de 18 actores provenientes del sector público, privado, sociedad civil y la academia, el Grupo Impulsor (GI), que bajo el liderazgo de MINEM y GORECAJ, i) Acordaron y suscribieron un objetivo común: el desarrollo de la región; ii) Acompañaron la constitución Aportes Ciudadanos: expectativas de la ciudadanía para Cajamarca al 2030, y su articulación con el PDRC y Acuerdo de Gobernabilidad en construcción; iii) Propusieron acciones estratégicas y proyectos/iniciativas que respondan a los objetivos planteados por la ciudadanía.

Sep 29, 2023

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921

By Robert Linton

Tats paper deals with work that has been carried on for over three years by the management and staff of the North Butte Mining Co. in an effort to standardize mining methods, to eliminate lost motion in the operating organization, and to improve the efficiency of the individual workman. Naturally, much of this work is an adaptation of ideas suggested by other mining operations or by practice in manufacturing and other productive industries. The studies, however, have developed some features that it is believed are new. Both new and adapted features are given in detail. The normal capacity of the North Butte mines is about 2000 tons per. day. Hoisting is done principally through the Granite Mountain shaft, which is 3740 ft. (1140 m.) deep and equipped with an electric hoist capable of hoisting 200 tons per hour from a depth of 4000 ft. (1219 m.). The lowest stoping level is the 3400-ft. The Granite Mountain shaft is connected with the Speculator shaft, about 850 ft. (259 m.) south, and with the Gem, about 1150 ft. (350 m.) east, which are 3000 (914.4 m.) and 2000 ft. (609.6 m.). deep, respectively. These two shafts are equipped with reversible fans for ventilation. The Speculator has a; steam hoist with a capacity of 150 tons per hour from the 3000-ft. level. The Granite Mountain shaft is concrete lined from the 1600-ft. to below the 3000-ft. level and gunited with cement from the 1600-ft. level to the surface. Sections of the Speculator shaft with a total combined length of 500 ft. (152.4 m.) are also concreted. There are approximately 36 miles (58 km.) of drifts and crosscuts in the mine, in which there are 15.2 miles (24.5 km.) of track. At normal capacity, about 75 stoping faces, 20 raises, and 30 sill development faces are working. Stoping is usually by the standard square-set method. Where the size of the oreshoot and character of. the walls permit, the rill (or cut-and-fill) system is employed.

Jan 8, 1920

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Renato P. Cunha

The paper explores a parametric analysis of a four-pile group in contact (hence piled raft) and without contact (hence standard pile group) with the superficial soil layer, under a combined set of loadings (moment M, vertical V and horizontal H forces). The major design parameters of interest, as total and differential settlements, and raft bending moments and shear stresses are assessed under aforementioned distinct conditions. The slenderness ratio of the piles is also varied along the analyses, allowing the establishment of its influence on the derived parameters.

Jan 1, 2006

By C. E. Corson

Discussion of the Paper by C. E. Corson, which was presented at the London Meeting, July, 1906. (See Bi-Monthly Bulletin, No. 11, September, pp. 725 to 742.) ALBERT SAUVEUR, Cambridge, Mass. (communication to the Secretary*) :-On close examination I think it will be found that the evidence by which Mr. Corson claims to have shown the inaccuracy of a statement I made a few years ago, is far from convincing. This statement is:- "Hot work, as such, has no influence upon the structure of the metal. Indirectly, however, by retarding crystallization until a lower temperature is reached, it may influence its structure most decidedly ; but the same results could be accomplished by heat-treatment alone, i.e., by reheating the unworked metal to the temperature from which the unworked piece was allowed to cool undisturbedly." The Metallographist, vol. ii., p. 267 (under the head of "Changes of Structure Brought About by Work"). Of the two pieces of steel tested by Mr. Corson, one was worked and finished at a " cherry red " and ' the other reheated to a cherry red, and the assumption was made that, in both cases the temperature was about 715° C., although no pyrometric device was used to record it. The possibility of considerable difference in temperature alone is so great as to invalidate Mr. Corson's inferences. The apparent temperature, moreover, is so close to the critical point of the steel as to render any conclusion very hazardous. -It is not at all evident that the annealed piece was reheated past its critical point, in which case reheating would have had practically no effect. Nor is it evident that the piece forged and finished at a cherry red was not actually below the critical point, which, by definition, I have called cold worked. Mr. Corson's explanation that " Under proper reheating, on the other hand, the steel becomes a solid solution from which crystals of approximate homogeneity and uniform size may separate" will not be readily understood.

Jan 1, 1907

By H. F. Haller, H. C. Pattison

The research program described in this paper is sponsored by the Advanced Research Projects Agency of the Department of Defense and monitored by the Bureau of Mines, United States Department of the Interior. PROGRAM DEVELOPMENT While Holmes & Narver is better known in other fields, the company has been active in many phases of underground excavation for over twenty years. In the 1950's, H&N participated in design and construction of nearly twenty miles of waste disposal tunnels in Southern California. As Architect-Engineer for the Atomic Energy Commission, we had design and management responsibility for many miles of tunnels and for thousands of feet of exploration and big hole drilling, from coast to coast in the States, and for gas well completions and exploration drilling for the Navy and the National Science Foundation from Pt. Barrow to Byrd Station in Antarctica. In my ten years with the company, we contributed to the development of big hole drilling techniques at a number of sites and analyzed the capability of boring machines for many of the tunnel projects. In a 1965 engineering study of a hundred miles of vehicular tunnels in rock under New York City, we investigated

Jan 1, 1997

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 488.-Mining engineer, member, technical graduate, married, age 38, desires position of superintendent or assistant superintendent. Has had 15 years' practical experience as miner, millman, machinist, surveyor, engineer, foreman, and superintendent in the West, Southwest, and Mexico. Speaks Spanish. Now employed as superintendent of copper property in Southwest. Can give the best of references. Minimum salary $250. Available after Sept. 1. No. 495.-Member, age 36, married, technical, 10 years'. all round

Jan 12, 1918

By Courtney W. Shea, Dennis Clark

Reckless blasting can have tragic consequences: The death of an innocent traveler, the financial demise of a coal company, and even criminal prosecution. In June 1993, a Tennessee coal mining company was blasting to loosen overburden at its surface mine. The mine was located immediately adjacent to the right-of-way of the northbound lane of Interstate 75. The approved permit included special precautions to be taken when blasting in the area closest to the interstate, including monitoring traffic so as to blast when the northbound lane was clear.

Jan 1, 1998

[Participating Scholarship Colleges and Universities 136 Big Sky Coal Company 111 Canyon Fuel Company LLC 97 Coal Age Magazine 109 Commercial Testing & Eng. Co 99 Continental Conveyor & Equip. Co 103 Copper Mountain Resort 128 Dakota Coal Co 100 DBT America Inc 117 Empire Machinery 101 Energy West Mining Co 102]

Jan 1, 2001

By John F. Abel

AIME is closing the books on its first 100 years. In the next year the meetings and many papers will doubtless be filled with statistics on the growth of AIME, and, incidentally, on the mining industry. Let's try to keep our cool and avoid breaking our arms patting ourselves on the back. AIME, nationally and locally, runs on the drive and dynamism of a rather small number of its members. If you look at the annual SME Blue Book of national officers and committee members, you will be struck by the repetition of the same names throughout. Trend for a few men to shoulder the burdens and responsibilities can be seen on the local level, too.

Jan 1, 1970

By A. McLean, L. Gao, Z. Shi, Y. D. Yang, K. Chattopadhyay, G. F. Zhang

Levitation melting of metals is one of the emerging applications of magnetic and electric fields in liquid metal refining. The varying magnetic field generates induced current inside the metal droplet and leads to the Joule heating effect and Lorentz force against gravity. This contactless process can avoid contamination from the crucible and can be used to produce high-purity materials. Visualization of the levitation melting process is difficult, and thus generally investigated by mathematical modeling. In the present study, a three-dimensional mathematical model of metal levitation was developed using finite element method for proper understanding of the levitation process. The effects of harmonic magnetic field frequency, coils power input, and sample size on levitation nickel droplet were investigated. Temporal evolution of temperature fields were predicted directly though the model. Levitation and balance condition of the droplet were investigated as well.

Jan 1, 2015

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.

By Brown D. N, Troth D. A

Large blast furnaces demand high standards of preparation of feed materials which must meet tight specifications of chemical and physical quality. Measurement of these factors must be expeditious but the nature of the coke, sinter, ores and fluxes and the large tonnages involved requires substantial mechanical sampling plant. The equipment, its operations, and its problems, associated with the 5000 t.p.d. No.5 blast furnace at Australian Iron and Steel Pty. Ltd., Port Kembla, are described and the efficacy of chemical blending achieved in the ore blending yards and sintering operation, is reported.

Jan 1, 1976

By Zay Jeffries

Each generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwithstanding their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization. It will remain for future generations to determine whether there is now going on a gradual change toward greater importance of the non-ferrous metals, as compared to iron and steel. The world's pig iron production in 1920 was slightly more than twice what it was in 1890, whereas the non-ferrous metals production in 1920 was about two and one-half times that in 1890. Every non-ferrous metal industry has shown marked growth during the last thirty years. During this period, the production of cop-

Jan 1, 1924

By Edward I. Salkovitz

RECENTLY a set of crystallographic angles for bismuth was calculated and a standard (111) projection was constructed. Since these calculations

Jan 1, 1957

ALTHOUGH the committee appointed by the President of the American Iron and Steel Insti-tute, to consider the twelve-hour day work in the steel industry and report conclusions and recommenda-tions, has made a very careful and painstaking study of the facts and figures developed, it is not yet ready to make what it would designate a final report. Apparently the underlying reason for the agitation which resulted in the appointment of this committee was based on a sentiment (not created or endorsed by the workmen themselves) that 'the twelve-hour day was an unreasonable hardship upon the employees who were connected with it; that it was physically injurious to a large percentage of the employes; and that it interfered with family associations essential to the welfare of the children; that for these reasons it was, in a sense, opposed to the public interest. TWELVE-HOUR DAY NOT NECESSARILY INJURIOUS Whatever will be said against the twelve-hour day in the steel industry, investigation has convinced this committee that the same has not of itself been an injury to the employes, physically, mentally or morally. Whether or not, in the large majority of cases, twelve-hour men devote less time to their families than the employes working fewer hours is perhaps questionable. A part of the manufacturing of iron and steel is necessarily continuous. Therefore, practically, there must be two shifts of twelve hours or three shifts of eight hours. The workmen, as a rule, preferr the longer hours because it permits larger compensation per day. It is asserted with confidence that there is less phys-ical work, as a total per day, and less fatigue from the work of the twelve-hour day in the steel industry, than pertains to the large majority of the eight-hour men. This is because in the former case there are more rest periods during the twelve hours on duty.

Jan 6, 1923

By G. Sauer

"More Skill is needed to avoid rather than to handle heavy ground loads." This finding, from a tunneling engineer of the nineteenth century, is still relevant today with all advanced sequential excavation and support methods available whether they are applied in the vertical or horizontal direction. Balanced contractual agreements and documents are important since they provide the spirit and climate at the site. This article aims to describe the means and measures for 'hand mined' shaft and tunnel support as they are available today. Some special construction elements and methods with a perspective in recent developments in order to avoid getting stuck in conservatism are presented as well. If we don't allow new methods, means and measures we may end up with the famous quote "Only women who have already proven they are able to give birth to a healthy baby are allowed to become pregnant!"

Jan 1, 2003