Search Documents

By K. Ohmori, K. Takeya, S. Yoshizawa, A. Kawamoto, T. Ishikawa

"High performance Sm2Fe17N3 magnet powder is developed nitriding Sm2Fe17 alloy that 'is made using a reduction and diffusion method. Typical remanence, coercivity and maximum energy product of the fine powder are 1.40 T, 1.13 T and 323 kJ/m3, respectively. Decreasing samarium content, oxygen content and the amount of a-Fe are found to be the important factors to realize high-energy product.High performance injection molded Sm2Fe17N3 anisotropic magnet is also developed using the powder and an original binder system developed in order to mold at low temperature. Typical remanence, coercivity and maximum energy product obtained are 0.77 T, 0.78 T and 103 kJ/m3, respectively in the density of 4.77 Mg/m3The temperature coefficient of remanence is -0.07 %/K and that of coercivity is -0.54.%/K. The initial irreversible flux loss of the magnet that has a permeance of two is -5 % at 100 °C and the irreversible .flux loss of it is -4.4 % exposing it at 80 °C for 1000h.IntroductionSm2Fe17N3 alloy powder is expected to be very useful for a bonded magnet. The reasons are as follows. The magnetization is as large as the Nd2Fe14B alloy. Curie temperature is even higher than the alloy. The uni-axial anisotropy is comparatively higher than the alloy. Consequently it is possible to obtain high coercivity after just milling the powder and therefore possible to obtain high-energy product in a bonded magnet as it is realized in the SmCo5 bonded magnet. On the other hand, sintering is difficult because it will be decomposed into samarium nitride and a-Fe when heating it up to 500°C:"

Jan 1, 2000

By M. Vallée

"Geological and technical problems are often considered the most important ones affecting new mining projects. Typical problems and likely causes are reviewed based on current Quality Management and Continuous Improvement (QMCI) perspectives, giving particular attention to the work of W.E. Deming. As the “system approach” is an essential part of these policies, its characteristics are described with particular attention given to cultural- behavioural, organizational and systembased constraints described by J. Gharajedaghi. Given that poor communication and interaction among geologists, mineral processors and mining engineers/operators can seriously affect the adequacy of tests, project planning and execution, and mine profitability, these interrelated processes within the mining systems are analyzed and modelled. The impacts on models and simulations of ignoring typical data, information and knowledge uncertainties are addressed. Adapting W.E. Deming’s Fourteen Points, System of Profound Knowledge and insistence on leadership, and the analysis of mining system constraints, will allow the effective QMCI approach required to reduce geological and technical risks. Whenever we achieve this goal, we will be in a better position to overcome environment-, market-, finance- and community-related problems, achieve higher company and industry profitability as well as more sustained development. RÉSUMÉLes problèmes géologiques et techniques sont souvent considérés les plus importants parmi ceux qui affectent les nouveaux projets miniers. Des problèmes typiques et leur causes sont étudiés dans la perspective de gestion de la qualité et d’amélioration continue (GQAC), en relation avec les travaux de W.E. Deming. Comme l’approche système est au centre de ces méthodes, ses caractéristiques sont décrites en donnant une attention particulière aux contraintes de types culturel-comportemental, organisationnel, et systémique décrites par J. Gharajedaghi. Compte-tenu que les lacunes dans les communications et les interactions entre géologues, minéralurgistes, et ingénieurs/opérateurs miniers peuvent affecter sérieusement la validité des essais, de la planification et de l’exécution des projets ainsi que la rentabilité des exploitations, ces processus connexes font l’objet d’analyse et de modélisation. Les impacts sur les modèles et les simulations de l’incertitude des données, informations et connaissances sont soulignés. En adaptant au système minier les Quatorze Obligations et le Système de connaissance approfondie de W.E. Deming ainsi que l’analyse des trois types de contraintes, nous pourrons développer une approche GQAC permettant de réduire les risques géologiques et techniques des projets miniers et des exploitations. Ceci nous pemettra de mieux faire face aux problèmes reliés à l’environnement, aux marchés, au financement et aux conditions sociales, d’améliorer la rentabilité des exploitations minières et de l’industrie, tout en contribuant de façon accrue au développement durable."

Jan 1, 2003

By David J. Gurtler

In early 1988, Chino Mines Co. began using a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction electrowinning plant feed, and non-ore material, to determine its disposition. Results thus far indicate a significant increase in financial returns on material mined compared with the copper cutoff grade previously in use. Chino Mines is a partnership between Phelps Dodge Corp. (two-thirds ownership) and Mitsubishi Corp. (one-third ownership). The company produces copper and byproduct metals from the historic Santa Rita del Cobre mining district in southwestern New Mexico. The history of copper production in the district began with the use of surface native copper by native Americans before 1800. Spanish soldiers from Mexico later became aware of this district and mining began in 1801. The district was worked intermittently until 1909 when the Chino Copper Co. was formed, with Daniel C. Jackling as vice president and managing director. Concentrator operations were started in 1911. Kennecott purchased the company in 1933 and built a smelter in 1939. Chino Mines Co. was formed in 1980 when Mitsubishi purchased one-third of Kennecott's holding at the property.

Jan 1, 1990

By J. J. Crowhurst

The modem open pit-heap leach operation by Pegasus Gold Ltd. at Zortman and Landusky in Phillips County, Montana, is a new chapter in the mining of gold in these districts. The discovery of bulk tonnage ore bodies and their development and ultimate production was based on a long history of mining and exploration in that part of Montana. Gold was originally discovered in the Little Rocky Mountains as placer deposits by Pike Landusky and Lou Myers. This discovery in the 1880s was not significant, but Pike Landusky continued prospecting for lode deposits, and he eventually located the Gold Bug and Little Ben, two of the larger Au-Ag producers in the district. Eventually two camps, Landusky and Zortman, grew in the LittleRocky Mountains. By the time Landusky was killed in 1894 by Kid Curry, the district was still a discontinuous small producer. Steady production commenced in 1907 with the organization of the August Gold Mining Co. Eventually high grade ores on specific veins were exhausted by selective underground mining and the district was idle by May 1942. After World War II in the early 1950s. E.A. Scholz tried to continue selective underground mining, but he realized the stockworks surrounding the larger veins constituted bulk tonnage targets. Ultimately in the 1976- 1979 period he organized two exploration efforts, one each for the Landusky and Zortman areas, and brought these into production as the Argo and Pegasus gold mines. By the time of his death, Apr. 8, 1980, both operations were producing gold. Later the two companies were merged as Pegasus Gold Ltd. Upon the death of Scholz, V.F. Hollister continued as the geological consultant, Ed Roper was engaged as general manager, and J. J. Crowhurst was given the responsibility of executive vice president. The discovery of open pittable ores and the application of heap leach technology was important in the development of mining. Both contributed to the low cost operation that continues to this day. The attached article by L.M. Rogers, then chief geologist, and M.S. Enders, his assistant, describes the geology of the deposit. It was presented at the Northwest Mining Association meeting in 1982.

Jan 1, 1990

By W. H. Bassett

THE ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst.

Jan 2, 1922

By M. P. Nesterov

The method of predicting the time-dependent surface subsidence for gently-inclined potash deposits where total extraction using various sizes of yielding bamier pillars was discussed.

Jan 1, 1998

By Kenichi Fujino

Severe disasters have struck Japan in recent years. Following these disasters, construction robots have played important roles in investigation and restoration work in the disaster regions. To be applied in this way, construction robots require many functions according to the purpose of their use in each case. There are clear differences in the functions and usage conditions required by investigation robots and those required by execution robots. These differences will be important when designing and operating construction robots in the future. This report introduces a volcano exploration robot and unmanned execution system as examples of construction robots used for investigations and executions respectively. Based on this, the report organizes important characteristics of construction robots and explains differences in the concepts of disaster investigation robots and disaster restoration robots. Because they are used in harsh natural conditions and do not have any execution functions, efforts are made to clarify the fact that investigation robots have to overcome many problems such as mobility. When a construction robot is used, the scenario of the operation of the construction robot (execution plan) is extremely important, and in addition, it is necessary to clearly define the way it will be used according to the purpose of its use and specification conditions. In a plan for an unmanned execution system, it is possible to mitigate several strict prerequisite conditions by proposing a well-constructed execution plan. For example, the execution efficiency of an unmanned execution system can be improved by effectively using a temporary road.

Aug 1, 2013

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By P. R. ZETTWOOG

HISTORICAL BACKGROUND A program in France to develop personal [a] dosimeters has been initiated 1974. The patent on which is based the present device was obtained in 1972 * . From 1972 to 1974, the possibilities of applying certain ionograph track detectors to the spectrodosimetry of radon daughters was explored. The first prototype were produced in 1974. It took four years (from 1974 to 1978) to produce an autonomous dosimeter whose components has a sufficient life span, especially for the turbine motor unit. Qualification in the laboratory was obtained in 1977. In 1978 it was obtained in the mine for technology (autonomy of 12 hours and a life span of more than one year) and in 1980 for monitoring. 300 dosimeters have been tested in underground mines all together. Indispensable peripheral equipment were also developed from 1976 to 1980 : calibration devices, equipment to prepare and develop the films, read out systems. The concept of an "Integrated System of Individual Dosimetry" (ISID) based on a personal [a] dosimeter measuring exposure to radon daughters, thoron daughters, ore dust and external irradiation doses was proposed at the end of 1980. Since January 1st 1981, ISID is used on a routine basis in some french mines, situated in remote area, and appears to be very competitive with the ambiant dosimetry. The latest version of the dosimeter is produced in mass series since June 1981 and should equip all french mines in 1982. DESCRIPTION OF THE INSTRUMENTATION DEVELOPMENT OF THE DOSIMETER MEASURING HEAD The measuring head is based on the use of ionographic film to detect a tracks. In fact, the measuring head is a spectrodosimeter which measures separately over the period of exposure: - the potential [a] energy inhaled due to the decay of Po 218, Po 214, and Po 212 ; - the number of Rn 222 atoms inhaled ; - the inhaled total [a] activity of the five long-lived emitters present in the ore dust. The contribution to the total inhalable potential [a] energy of these various radionuclidesin a typical underground mine is studied in Appendix I. The measuring head described in detail in Appendix II, is able to satisfy all the implications made in the ICRP recommendations. Appendix III deals with the use of this measuring head in the cases where the equilibrium factor is lower than 0.1. This situation occur in open-pit mines where account must be taken of the Rn 222 contribution, which is no longer negligible in relation to that of its daughters. CURRENT DOSIMETER PERFORMANCES Table I shows the characteristics of the latest dosimeter. Appendix IV should be consulted concerning qualification of the dosimeter in the laboratory and in mines, technological development which finally produced the [a] dosimeter and its peripheral equipment, and technical presentation of the ISID (Integrated System of Individual Dosimetry) based on the concept of a multirisk personal dosimeter. Data on the installation and operating costs of such a dosimeter, which would seem to be competitive, are also given in this Appendix. ADVANTAGES OF PERSONAL DOSIMETRY AS COMPARED TO AREA MONITORING The results of the first eight months of experiments carried out under real conditions in an underground mine site are given in detail in reference 8. Area monitoring : The monthly exposure per worker to inhaled Rn 222 was determined from the knowledge of time spent in various areas of the mine and for the different mining operations, as well as from numerous and systematic sampling of the Rn 222 concentration in all work places. Personal dosimetry : The exposure to potential energy from radon daughters was measured by an [a] dosimeter developed by the CEA and worn by each of the 160 miners during eight months. In this way 160 x 8 pairs of monthly individual exposure values have been obtained which can be statistically studied. This test was decisive for us because it proved that the [a] dosimeter was technically sound (very few defects over one year for 160 dosimeters) and especially that personal monitoring devices were superior to area monitoring devices. The following conclusions can be drawn 1. The exposure distribution obtained by personal dosimetry is log-normal. This is true for the results on the whole as well as for groups of results relating to certain explanatory variables. See fig. la, 1b, 1c. 2. The exposure distribution obtained by area monitoring does not correspond to any type of distribution. If the results of personal monitoring are taken as a reference, area monitoring tends to underestimate the high exposures and overestimate the low exposures.See fig. 2. 3. [a]-energy exposures are underestimated when calculated from radon exposures and the equilibrium factor found in the considered mines. This is due to episodes or to zones of high radon concentrations not registered

Jan 1, 1981

By V. C. Robinson

INTRODUCTION Most presidential addresses are in the nature of a review of some specific topic and this will be no different. In thinking about the subjects which might be suitable for this address I decided that as next month will see my retirement from the gold mining industry I might review the four decades since I started in the industry in 1929. These four decades have been more than usually in',~resting and exciting. They have covered a period when the price of gold increased from the old figure of 84/- an ounce to the price of $35 an ounce today, taking in on the way at least two periods of premium sales from which the producer benefitted. The industry in these four decades has survived the most totally destructive war in history and has seen fundamental changes in the political, economic and governmental life of South Africa. There have been great technological changes and improvements, some of which I shall refer to later, and in addition there have been profound changes in the relations between employer and employee in the industry which have affected not only the economy of the industry but the traditional thinking of both management and labour. I believe that the address presented to this Institute on the occasion of its 75th Anniversary by Mr Goode covered more than adequately the history of the Institute and the part it has played in the mining industry of South Africa. It would be merely repetitive, therefore, to discuss the affairs of the Institute of Mining and Metallurgy. Having said this, however, it is also necessary to point out that the history of the Institute is, and always will be, an important record of the history of mining in South Africa. There are many facets, however, on which we ought to look back and to re-examine. One of the most rewarding, but at the same time one of the dullest, places to look for historical facts is in the annual reports of the Chamber of Mines. I suppose that some of the dullest of these have been the reports for which paragraphs have been prepared by me personally. The notes which follow do not claim to be anything like a full record of this exciting period. RISE AND FALL OF THE GOLD MINING INDUSTRY In talking about the mining industry of South Africa it is inevitable that one talks, particularly in the historical sense, about the gold mining industry - an industry of fundamental importance which has made South Africa what it is and which has been dying since the early part of this century. In Table I is shown the progress of the gold mining industry measured by its output of ounces of fine gold from the beginning of operations until the end of 1969, and if you are interested in the productivity of the men who work this industry the table, composed entirely from figures set out in the Chamber's annual reports, also shows the production of gold expressed as fine ounces per European and fine ounces per Bantu worker over a long period. If you are still minded to think of this industry as dying then the last column in the table shows how uranium has played such a vital part in the prosperity of the country.

By James Watson Baxter

Fluxes are used to promote pyrometallurgical processes that rely on adhesion (soldering or brazing) or fusion (gas and arc welding) to join metallic surfaces. In the adhesive processes, the metal surfaces to be joined are not melted; the join is formed using a filler metal with lower melting point than the base metal. Fusion welding involves use of heat in excess of the melting point of the base metal. The fused joint may be achieved either by simply fusing together metal surfaces brought in contact with each other or by introducing additional molten metal of similar composition to form a fused joint. ADHESIVE PROCESSES--SOLDERING AND BRAZING In order for molten filler metal, solder or braze, to spread in a manner that creates a successful join; the work surfaces on the base metal must be thoroughly cleansed. Fluxes remove stubborn oxide films and other surface contaminants, promote wetting of the work surfaces, add fluidity to the solder or braze, and enhance workability and ease of spreading. Brazing processes involve higher temperatures than those reached in soldering. Brazing fluxes, which must remain active and effective at the higher temperatures, differ from those employed in soldering. Some common fluxes used in adhesive processes are rosin for soldering tin and electrical connections, hydrochloric acid for use in soldering galvanized iron and other zinc surfaces, and borax for brazing. Soldering and brazing are similar processes, the primary difference being the temperature at which the joining operation is carried out. Soldered joints, produced with low-melting-point fillers (solders) that melt and flow at temperature less that 450°C (Althouse et al., 1988) can sustain loads of 1 to 1.7 MPa for extended periods of time (Anon., 1966). Brazing involves the use of filler materials with melting points commonly above 500°C and generally provides stronger joints than those obtained with solder. Both processes require local application of heat to melt and spread the filler so that the molten filler can wet (adhere to) the base metals by alloying and diffusion. Soldering Soldering is a means of joining metals by adhesion using a metallic bonding alloy as the filler, commonly a mixture of lead and tin. However, the adhesion of solder depends more on its ability to be keyed into minute surface irregularities than on alloying. The most familiar application is to provide and secure electrical connections. Soft solders can range from 1 to 70% tin with the remainder mostly lead. However, for general-purpose, soft-solder work, the alloy is commonly 50% lead-50% tin. Higher lead contents provide a wider range in the melting temperature and, for this reason, a 60% lead-40% tin alloy, which yields a mushy mixture, is used for wiped joints in lead sheet and pipe work. Conversely, 40% lead-60% tin alloys are used in soldering tin and other low- melting-point materials for which a narrower range of melting temperature is required. There are numerous other solder compositions such as tin-silver, 95% tin-5% silver and antimony-tin, 95% tin and 5% antimony (Carlin, Jr., 1992). Heat needed to melt and spread the solders is commonly provided by electrically heated, copper-tipped soldering irons or by means of torches; the solder is applied by hand, usually face-fed by means of wire. For wiped joints in plumbing and lead-cable splicing, the solder is manipulated with cloth pads. The molten solder wets the joint surfaces and is drawn, by surface tension, into minute fissures and capillary openings. Other applications involve use of induction heaters and furnaces with pre-shaped solder appropriately placed prior to fluxing and heating. In some processes, the joints are immersed in molten solder. Constituents and Role of Soldering Fluxes: Soldering fluxes generally fall into one of three categories: highly corrosive fluxes, intermediate fluxes, and noncorrosive fluxes. These same categories are sometimes designated inorganic, organic and rosin-based respectively (Althouse et al., 1988). Common constituents of each group are discussed briefly below. Corrosive Fluxes (Inorganic). Work with aluminum, magnesium, stainless steel, high alloy steel, aluminum bronzes, and silicon bronzes is carried out at temperatures in the upper portion of the range for solder operations. Soldering these materials requires use of highly active, corrosive fluxes to remove and prevent the formation of the especially stubborn, hard, oxide films that form on these materials upon exposure to the atmosphere. The corrosive fluxes consist of inorganic acids and salts that are applied either as pastes or dry. They are active at elevated temperatures and, since they remain active after the soldering is completed, must be completely removed. The main constituent of most corrosive fluxes is zinc chloride with a melting temperature well above the solidus temperature of most commercial tin-lead solders. It is made by the action of hydrochloric acid on zinc. When zinc chloride is used alone, un- melted particles of this corrosive salt get caught up in the joint and weaken it. For this reason, other inorganic salts such as ammonium chloride (NH4Cl) or sodium chloride (NaCl) may be added to lower the melting temperature. A mixture of zinc chloride and ammonium chloride is very effective because the excellent oxide reducing properties of ammonium chloride and the protective action of the molten zinc chloride combine to produce a fluxing action superior to that achieved when either is used alone. In addition to zinc chloride, ammonium chloride, and sodium chloride; common con-

Jan 1, 1994

By Fábio Heiji Yamada, Marcelo Koiti Fugihara, Ruano Fonseca Araujo

Conception the simulation and optimization technologies for industrial processes applied in the mining environment: tools and methodologies. Clarifications provided about the differences of these techniques when compared with static analysis (intuition, use of static spreadsheets, etc.). Presentation of practical cases at several big mining companies in Brazil. These projects will be presented and illustrated through dynamic simulation models developed at those companies, each one with its set of objectives, scope and results (for example: sizing the number of equipment, silo, piles related to the mining processing, logistics, ROM transportation, mine operations plan, etc.).

Oct 3, 2019

By D. R. Corson

The Bureau of Mines instrumented two similarly backfilled stopes--one filled in the normal manner and the other with the fill densified using vibratory compactors--to evaluate the effect of fill compaction on subsequent vein-wall closure proposed as a adjunct process for strengthening cemented fill. Hydraulic pressure cells to monitor pressures within the fill and mechanical closure devices to measure vein-wall movement and the procedure for their installation are described. The field compaction work was generally performed manually by utilizing small commercial concrete vibrators. A prototype immersible vibrator using slusher cables to propel the vibrator in the stope was used on several lifts of fill. Although compaction efforts were less effective than anticipated in increasing the final density of fill, analysis of the field data does indicate somewhat improved strain characteristics and an increased pressure buildup for the densified fill. The effects of a prolonged period of inactivity and of rock burst occurrences in the immediate area are also reflected in plots of strain and pressure within the two instrumented stopes.

Jan 1, 1971

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By D. J. Duck

INTRODUCTION Construction of the 3,600,000 kilowatt Third Powerplant at Grand Coulee Dam started in late summer 1967 approximately one year after authorization by Congress. The project was made possible by a treaty with Canada providing for cooperative development of the Columbia River which was signed in 1961 and ratified in 1964. Description of the Work The existing Grand Coulee power complex consisted of a dam and two powerplants with a switchyard serving each plant, one on each bank of the river. See Fig. 1. The switching facilities were connected to transformers at the powerplants by overhead 230-kilovolt and 115-kilovolt tie circuit conductors. [ ]

Jan 1, 1997

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

Maximising margins in today's competitive international commodity markets demands superior productivity. This requires more than selecting the best equipment. It requires continually improving the efficiency of production, commercial, marketing and administrative processes under the control of solid modern management systems.This paper introduces an integrated way of working that includes proven management systems for successfully changing work practices and attitudes, developing managers and increasing accountability. It introduces a proven methodology for systematically involving people in sustained true continuous improvement of processes for maximising productivity, safety and revenue while minimising costs.

Jan 1, 1998

By John S. Berber

Bureau of Mines research on the production of phthalic anhydride by vapor phase oxidation of hydrocarbons began at Morgantown, W. Va., in October 1960. For these preliminary studies, a known solution containing naphthalene and 1-methylnaphthalene was used. In another series of tests, pure naphthalene was dissolved in different solvents. A series of investigations was conducted with the neutral oil fraction (210° to 270° C) of a low-temperature tar obtained from the Texas Power and Light Company's low-temperature carbonization unit. The neutral oil fraction was first dealkylated, and then the product was distilled into 210° to 250° C and 250° to 270° C fractions. These two fractions were then subjected to catalytic vapor phase oxidation. Although a number of catalysts was tested, most of the experiments were made using 9 percent vanadium pentoxide on inert alumina. The activity of this catalyst did not decrease after 162 hours at 1,030° F. Studies were conducted over a temperature range from 610° to 1,180° F. An operating temperature of 1,030° F yielded 47.50 percent of phthalic anhydride from a synthetic mixture of naphthalene and 1-methylnaphthalene. The highest yield (84.40 percent phthalic anhydride) was obtained with naphthalene dissolved in toluene and also with naphthalene dissolved in methyl ethyl ketone. With a 210° to 250° C fraction the highest yield of phthalic anhydride obtained was 12.32 percent at a temperature of 900° F, and, with a 250° to 270° C fraction, it was 15.80 percent at a temperature of 875° F.

Jan 1, 1963

By M. Uszko

Methane drainage and ventilation methods of methane hazard mitigation are used in the coal mines of Kompania Weglowa S.A. Over 22% of methane released during mining activities is captured by methane drainage systems and transported to the surface. In this article we present development plans for utilization of methane captured and transported to the surface by methane drainage systems. The results of research on the possibility of economic utilization of methane concentrated in ventilation air that leaves the mine through fan diffusers are also described.

Aug 1, 2013

By J. Gallegos, R. Faber, T. Cox

"An innovative method to reduce acid rock drainage (ARD) and sediment loading of a recreational lake was used in the Red River watershed in northern New Mexico. The Red River drains a mining district that contains multiple naturally occurring hydrothermal alteration zones that release ARD and sediment to the river during episodic summer rain storms. A lake is near the mouth of the watershed and is filled with water from the river through a sluice gate and diversion. An automated actuator was installed on the sluice gate to close when the river is impacted by high-suspended sediment. Water quality probes were installed at the sluice gate to monitor the river water for turbidity, specific conductivity and water depth. If high turbidity is measured, the sluice gate closes automatically. Remote access is setup with a computer view screen to review the real-time system status. Once the turbidity drops below a threshold, the sluice gate is reopened remotely. The automated sluice gate has successfully reduced the amount of ARD and suspended sediment entering the lake. This reduction has resulted in an improved aquatic habitat for the fishery and benthic macroinvertebrate community. BACKGROUND The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. The river drains an area of approximately 190 square miles and spans elevations from 6,600 feet at its confluence with the Rio Grande to its headwaters near 12,000 feet (Figure 1). The river generally flows to the west along most if its length.The Red River watershed includes several hydrothermal alteration zones. The alteration zones were created by intrusion of high-silica granites and subvolcanic porphyries, with associated hydrothermal fluids, into the volcanic rocks of the Questa Caldera. The hydrothermal alteration is also responsible for the molybdenum deposits in the area. Rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks has resulted in the formation of alteration scars. The alteration scars are characterized by steep, erodible slopes with little vegetation and incised gullies. Debris fans from the drainages containing active alteration scars have formed and typically consist of poorly sorted sand and gravel that is distinctly pale yellow in color. Some of the more prominent scars are located in the Hansen, Straight and Hottentot Creek drainages downstream of the town of Red River."

Jan 1, 2018