Search Documents

By C. J. Bise, D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard- recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Feb 24, 1997

By T. Maruyama

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. has been operating with one Flash Furnace (FSFE) and three Peirce-Smith Converters since its start-up in 1972. Anode production capacity has increased from 101,000 to 263,000 t/y by the several expansion programs, while converter capacity has increased and stable operation has been established by several improvements as listed below. - Expanding the furnace body (length) - Development of two kinds of automatic scrap charging system for each converter. (Increasing the in-stack time and better control of the melt temperature) - Oxygen enrichment at slag blow and copper blow - Increasing the blowing rate This paper reports the details of these improvements.

Jan 1, 1998

By J. Blodget Britton

During the last three or four years I have had occasion to examine, chemically, various samples of matter commonly called flue-dust or cinder, found deposited in the flues and hot-blast chambers and under the boilers of blast furnaces, and also in the flues and under the boilers of puddling and boiling furnaces. Recently several of these examinations mere made quite in detail, and as the results reveal, I believe, information of no inconsiderable importance, I am induced to communicate them to this Institute. A sample of deposit obtained from the flues of one of the blast furnaces at the works of the Phœix Iron Company, at Phœnixville, Pa., was found to have the composition given in Column I of the following table: I. 11. 111. Composition of Dust from Dust from Dust from Deposits. Blast Furnace. Puddling Furnace. Boiling Furnace. Protoxide of iron,... 1.51 3 08 1.18 Peroxide of iron,... 20.21 33.29 41.00 Alumina,....6.57 12.89 7.54 Lime,.....3.98 .48 .61 Magnesia,.....69 .09 .19 Protoxide of manganese,. . 1.66 .39 .12 Oxide of zinc,....2.84 ........ Oxide of copper,. .. ..06 ........ Silicic acid,....36.00 40.69 38.99 Sulphuric acid,... 7.55 .43 Phosphoric acid,..94 ..94 Arsenious acid,. .. .38 Antimoniousacid,... trace.......... Chlorine,....03 ..03 Cyanogen,.....09 ........ Ammonia,.... trace......... Pottlsh with some sodn,. .. 16.61 ........ Carbonic acid,. .. .. .59 ........ Alkalies, undetermined matter, and loss,.......29 4.49 6.96 100.00 100 00 100.00 Metallic iron,. 16.31 25.70 29.64 Phosphorus,. .. .. .41* 1.55† 1.30†

By Dr. O’Neil Thomas J., Donald W. Gentry

Introduction “A Western mine is a hole in the ground owned by a liar. . ." -Mark Twain THE CAPITAL INVESTMENT DECISION Decisions pertaining to a firm's proposed capital investments can have vital short- and long-term consequences on the organization's ability to compete, and even survive.Capita1 investment decisions, in general, center around two fundamental activities: (1) allocating capital funds to specific investment projects or assets, and (2) obtaining necessary financing in such proportion as to increase the overall value of the firm. In essence these activities or decisions describe the science of finance (as contrasted with economics). Fimnce has been described in general terms as the study of how a present, known amount of cash is converted into a future, perhaps unknown, amount of cash (Archer, Choate, and Racette, 1979). Fundamental to understanding the science of finance and the capital investment decision process in general are the basic concepts relating to cash flow transactions, time, income generation (markets), expected returns, and risk. The functions of finance may be segregated into three fundamental decisions which a firm must address: (1) the dividend decision, (2) the financing decision, and (3) the investment decision. These decisions are interdependent and their joint impact on the objective of the firm must be considered. This book primarily addresses the concepts and components associated with the investment and financing decisions as they affect the practice of mine valuation. Responsibilities of Management A primary assumption incorporated in this book is that the fundamental objective of any firm is to maximize its value, or wealth of its owners (stock- holders). Here, the term wealth refers to the total current market value of the firm's assets. In the case of corporations, the wealth or value is considered to be represented by the market price of the firm's common stock. The price of the firm's common stock obviously will be affected by its investment, financing, and dividend decisions. Consequently, an optimal combination of these three decisions should maximize the value of the firm to its stockholders. It is important to point out that wealth maximization is a more appropriate and inclusive goal for the firm than profit maximization. Indeed, there is a difference between the two objectives in most situations. For instance, a firm can always raise profits by selling stock and investing the proceeds in treasury bills or certificates of deposit. This type of activity, however, would rarely cause net shareholder wealth

Jan 1, 1984

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By Sabine Noelte, Mikko Petteri Rantamäki, Christopher Robben, Anssi Takala, Karl-Erik Rånman

"Sensor-based ore sorting is on its way to establish as a standard option for physical separation. The increasing number of installations in coal, iron ore, industrial minerals and hard-rock metal mining segments underlines the technological and financial potential that is beginning to be untapped. The Ma’aden Phosphate installation with 1.650 t/h sensor-based ore sorter feed sets a new benchmark for the possible capacity of stationary installations. Besides stationary installations, including multiple sorters parallel in different size ranges and multiple stages, containerised semi-mobile plants are applied. These offer two advantages, first being the reduction of transport costs when applied close to the mining face. The second is that semi-mobile systems enable processing of tens of thousands of tonnes of ore in a piloting phase with an approximate duration of 0.5 to six months, verifying the results laboratory mini-bulk tests on 5–10 tonnes of sample. This is especially important for low-grade metal ores because of the inherent Fundamental Sampling Error, as well as the Grouping and Segregation Error. The paper elaborates the results achieved within the I2MINE project, treating polymetallic ore at the Boliden Concentrator in Sweden.INTRODUCTIONSensor-based ore sorting (SBS) is becoming a standard option for physical separation, applied in all segments of mineral production. The Umm Wu’al project sets the bar for stationary SBS installations with 1,650 t/h feed (TOMRA, 2015). TOMRA Sorting Solutions has finalised an agreement in cooperation with Outotec to supply Outotec-branded sorting solutions for the mining and metallurgical industry (TOMRA, 2014). Especially for low-grade hard rock metal ores, an interdisciplinary approach is necessary applying experts for all aspects of mineral production. Due to the impact on the whole process stream, it is important on the end user side to have high level managerial support and involve all disciplines to ensure that all stake holders are involved in the analysis."

Jan 1, 2016

By McMahon DW, Schapper MA

Hard rock underground mining has been wedded to the drill-blast method of breaking rock. Current practice and technology have focused on greater efficiencies in the blasting and handling of ore, on the basis that thelower costs that come with larger scale operations compensate for the waste dilution associated with the bulk methods. However, it is suggested that new technology is available or is on the horizon that could completely change the shape of hard rock mining in the 21st century. Hard-rock continuous-mining machines, possibly assisted by high pressure water jets, coupled with automated sorting and materials handling systems, could re-orient the miner&apos;s focus to winning metal rather than mining tonnes of ore. More continuous mining processes could accelerate the penetration by high technology in the hard rock underground mine, with the potential of greater manpower productivities and lower costs per tonne of metal produced. This new technology will be important in maintaining a competitive supply of metals, given the falling headgrades of the orebodies remaining for development and the increasing market threat from manufactured substitutes.

Jan 1, 1985

By Donald Bruce, Mark Harris, Wesley Schmutzler, James Sanders

"This paper evaluates the history, construction and most importantly the performance of two remedial seepage cutoff walls installed in two major dams in the United States. Beaver Dam, on the White River in northwest Arkansas, was completed in 1966 and seepage through the karstic limestone under the embankment was apparent almost immediately upon filling of the reservoir. Several attempts to stop the seepage by grouting were unsuccessful. In 1994 a cutoff wall consisting of secant piles drilled with 32"" diameter down-the-hole hammers to a maximum depth of 185'?was completed and the seepage was reduced to a negligible amount. It has been over 20 years since the completion of the cutoff wall, and all indications are that the cutoff wall is performing as expected. Walter F. George Lock and Dam on the Chattahoochee River near Fort Gaines, Georgia, was completed in 1963 and suffered the same problem as Beaver Dam due to the limestone on which the dam was founded. Cutoff walls were installed in both embankments (1980s) and solved the problem in these areas, but under-seepage at the concrete lock, dam and spillway structures increased to the point that remediation was essential. The cutoff wall had to be installed through 110'?of water and another 100'?into rock upstream of an active dam that continued to generate electricity during the construction of the cutoff wall. A secant pile wall, in combination with a diaphragm wall, was completed in front of these structures in 2004. It has been over 10 years since the completion this cutoff wall and, again, the cutoff wall is performing as expected. The paper describes the construction of these cutoffs, but focuses on the long-term performance in terms of controlling seepage and piezometric levels.BEAVER DAMBeaver Dam is located on the White River, 609 miles above its mouth, in Carroll County, Northwest Arkansas. The construction of the dam and Beaver Reservoir was authorized on September 1954 by the Congressional Flood Control Act for purposes of water supply, flood control and hydroelectric power generation. The dam site was selected in 1957: construction began in November 1960 and was completed in June 1966. (FIG. 1)"

Jan 1, 2017

"Technological innovation is an extremely complex activity. The author presents his interpretation of innovation and the innovative process. He reviews the strategy used by participants in coal mining innovation in the past and discusses changes required to meet the challenges of the future.Introduction if an industry is to be successful and viable in today&apos;s world, the companies active within the industry must remain close to the frontiers of knowledge. The coal mining industry is no exception. Technological problems facing the coal mining industry are basically economic and social. Economic problems are those concerned with the long-term growth and profitability and social problems, with the health and safety of the mine worker and the impact of the mining operation on the environment.Technological innovation can be a key factor in meeting these problems successfully. The general belief is that the information base for technological innovation exists within mining companies and governmental agencies but current industrial and governmental strategies and structures impede the transformation of this knowledge into the mining products and processes required for growth.The purpose of this paper is to determine where Canada is in terms of coal mining on the innovative ladder. The paper as presented: defines innovation and innovative process; gives an historical ""broad brush"" review o f innovation in the industry; and suggests the challenges to be faced in the future."

Jan 1, 1985

By G. A. Irona

Solids injection into non-ferrous converters and furnaces is becoming increasingly important for concentrate injection, removal of impurities, and recycling of dusts and other waste materials. The fundamental design aspects of these technologies will be reviewed, including gas and particle trajectories, lance clogging, heat transfer, and mass transfer including reaction rates and mixing. The use of soda ash for removal of impurities such as antimony and selenium will be used as an example of versatility of powder injection processes.

Jan 1, 1993

By Robert McEwen

Conveyor equipment beyond its prime chronically suffers from a lack of understanding in today&apos;s plant environment regularly delivers more material than original designers ever expected. A case in point is a belt conveyor in a major hard rock mine/milling operation asking to bring the unit up to current standards while eliminating spillage and reducing airborne dust. The challenge was to keep the system going by revamping the system while keeping the same footprint and allowing for higher production rate. Thirty years of daily maintenance and dust collection costs have virtually disappeared by the end of this challenging upgrade.

Jan 1, 2008

By George S. Evans

CERTAIN American operators believe that desulphurizing in the ladle offers a means of increasing blast-furnace and open-hearth yields with the possibility of improvements in quality of the steel. In fact, several producers have experimented with practically all of the known desulphurizing agents, including both standard grades of the alkalies and special preparations that have been offered from time to time during the past several years. Some of these are regularly being used today in large-scale commercial operations, with good results. Also, it is the practice to treat off-sulphur casts in the blast-furnace ladle at a number of plants. It is not known, however, that anyone in the steel industry (American) has ever adequately equipped a plant for desulphurizing blast-furnace metal in an efficient manner as regular operating practice. The purpose of this paper is to illustrate the importance of correct equipment and proper handling for obtaining uniform and efficient results. As will be shown, at the temperature of molten iron the alkalies are instantly neutralized by any free slag present, dissipating their desulphurizing value. Entrained silicates are rapidly washed out of the metal bath by the highly basic soda slags and will be satisfied ahead of desulphurizing reactions with FeS. More or less of the reagent will always be used up through reactions with the refractory lining. Desulphurization will be limited to the action of the free alkali then remaining in the slag. Causes for the erratic results generally found with desulphurizing tests in blast-furnace transfer ladles would include, among other things, variations in the quantity of furnace slag coming down with the metal, and differences in the percentage of kish and entrained silicates in the different casts. As the alkalies instantly unite with any free slags or silicates present, these, with any kish coming off, both dilute the reagent and reduce the surface contact between the slag and metal, thereby retarding the desulphurizing reactions.

Jan 1, 1938

By Victor F. Hollister

Skam deposits considered as porphyry copper deposits have been classified into three basic prospecting models: (I) the skam deposit associated with a mineralized intrusive (Pima-Mission), (2) the deposit associated with a barren igneous stock (Ertsberg), and (3) mineralized rock that seems to have no clear association with apluton (Phoenix). Pima-Mission, Christmas, and many other copper-bearing skarns developed in carbonate sequences near mineralized intrusives form an important part of the deposit. Historically, copper derived from the mineralized intrusion accounts for less than half of the metal produced by most porphyry mines, as most mineralization occurs in the intruded rocks. Skam mineralization is an important part of wall-rock metal deposition, because carbonate sequences are preferentially replaced by sulfide and skarn minerals. Exploration for skam mineralization is an important phase of porphyry copper exploration. Impure carbonate beds can become better host rocks for skam deposits than pure carbonates, and these in particular should be included in porphyry-exploration programs if the impure strata are cut by the stock. Skam deposits can also form near stocks that are barren of sulfide. In this model, the two best ore guides are strata favorable for mineralization (usually impure carbonate beds) and the intrusive contact. Faults can also act as important ore controls. Some skarn deposits form that have no clear genetic connection with a stock, although intrusive rocks are known in the district. In such cases, the best ore guides are strata and district-wide faulting. Dikes and sills are also common and mineralization can locally prefer their contacts even though the igneous rocks are barren. Skam minerals are influenced by the chemical composition of the carbonate. Forsterite, brucite, tremolite, and talc are common in skams developed in dolomitic beds. Skams derived from calcic beds often contain wollastonite, calcite, stilbite, or idocrase. Diopside, however, is a common accompaniment of copper sulfide in skam regardless of the original composition of the carbonates. Tremolite and possibly other amphiboles and chlorite can occur significantly in the zinc-lead portion of skams. Gamets occur in magnetite, copper, and zinc-lead zones of skams, but are not as diagnostic as diopside for the copper zone or tremolite for the zinc-lead zone. A general desciption of skam-deposit mineralogy can be used to construct prospecting models of porphyry copper skams. An abstract of such a description follows.

Jan 1, 1991

By C Glassock, P Tilyard, T Sandeman

Computer simulation is a well accepted tool for modelling the behaviour of large and complex operating systems. It is a particularly useful technique in complex operations where there are multiple interactions between the inputs and outputs of various unit operations. It can be utilised during the early stages of a project as part of the business case definition phase or the early engineering phases, or alternatively to help understand the various options available in an upgrade or expansion. With the design of a new processing plant to handle a different ore type at Lihir Gold Limited (Lihir), there was concern that the existing conveying system could separately handle the increased tonnages. A simulation model was constructed which allowed Lihir to examine the impact on the conveying system of the new process plant, as well as investigate the effect of different trucking options. As is often the case, once the simulation model was built, further understanding of the downstream bottlenecks was able to be investigated, including the sizing of critical equipment.

Jan 1, 2006

By C. F. Curry

In the early 1940&apos;s Humphreys Mining Company in Florida pioneered heavy mineral mining with a dredge in the United States, In 1948 Du Pont, in conjunction with Humphreys, opened their first of two mining operations recovering a titanium dioxide product in Florida. Later on in 1952 Du Pont opened their second plant, both of which used a cutterhead suction type of operation. This process is also used in heavy mineral mining in Australia and Africa. In 1957 ASARCO started prospecting in New Jersey. Test borings indicated a large deposit of ilmenite bearing heavy mineral sands had been deposited and concentrated in an area near Lakehurst in central New Jersey. Humphreys Mining Company was contacted about the possibility of mining the ASARCO New Jersey property in much the same way as Du Pont and themselves were doing in Florida. An extensive study was made to determine the economic feasibility of mining the ASARCO property. During this study, extensive test drilling and samples for a pilot plant were taken.

Jan 1, 1975

By Fennell B

A process for the recovery of cobalt from a speiss produced at Sulphide Corporation is presented. The speiss is leached in oxygenated sulphuric acid to dissolve the metallic iron at a pH of around 4. The resultant iron (11) is subsequently oxidized in the leaching vessel and precipitates as goethite. Acid is regenerated in the precipitation allowing dissolution of further speiss. Subsequent to the conversion of most of the iron in the speiss to goethite, conditions become sufficiently oxidizing to dissolve cobalt. Cobalt is not co-precipitated under the leaching conditions, yielding a pregnant solution containing the cobalt and some iron (11). The principal advantage of such a process is the significantly lower acid consumption over that obtained by complete dissolution followed by selective precipitation. An impure product of cobalt hydroxide can be obtained from the pregnant solution by neutralization.

Jan 1, 1983

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By C. H. Fulton

Page Introduction........................... 280 Distillation Products from Reduction of Zinc Ore........... 281 Preliminary Investigations..................... 290 Equilibrium of Reaction Zn + CO2 + ZnO + CO in Temperature Range of Condensation........................ 293 Requisites for Successful Condensation................ 299 Discussion............................ 300 Introduction The study of the condensation of zinc from its vapor was undertaken to shed light on certain problems encountered in large-scale electric zine-furnace work. recently conducted. It is a matter of common knowledge that one of the disadvantages of the arc type, electric zinc furnace, is the production of a large amount of blue powder and proportionately little liquid spelter, for, as stated by Stansfield,l "A notable defect in the electric smelting of zinc ores is the difficulty experienced in obtaining the distilled zinc in the liquid state; ...... when zinc ores are smelted electrically, very little liquid metal is commonly obtained, nearly all of the zinc being in the state of powder." This difficulty was not encountered in the electric furnace used12 the main difficulty being the destruction of the fire-brick lining of the large condenser, in certain parts, and the formation of .some oxide and dross coatings on the condensing surfaces. The reason for these difficulties could readily be explained by the infiltration of air whenever the condenser was changed from one retort base to the other, the zinc absorbed in the fire-brick forming oxide and causing rupture by its expending volume. Two facts, however, tended to disprove this theory for the rupture of the fire-brick lining: first, the large distilling retort, lined with fire-brick, which was shifted from charge to charge on alternate bases at temperatures between 1200 and 1300 C., fully exposed to the air, showed no signs of disintegration whatever; second, marked disintegration in the condenser occurred .only in places that were at tempera-

Jan 1, 1919

By M. D. Riegel, Brian T. Felber

"Construction of foundation elements in an urban environment is often complicated by multiple constraints such as existing foundations, utility conflicts, maintenance and protection of traffic on high volume roadways, low overhead clearances, and vibration and displacement monitoring to reduce risks of impact to existing facilities. Micropiles are commonly a preferred foundation alternative in an urban setting to mitigate some of these risks. This paper presents examples in which micropiles helped reduce risk in an urban setting on the two subject infrastructure improvement projects. The case studies presented include the Verrazano Narrows Bridge HOV and Bus Ramp Improvements in Brooklyn, NY and the Kosciuszko Bridge Replacement in Queens and Brooklyn, NY. The paper details the micropile design, how risks were mitigated, and the complications to each of these projects associated with the urban setting.INTRODUCTIONThe paper begins with background information about the Verrazano Narrows Bridge HOV and Bus Ramp Improvements Project, followed by background information for the Kosciuszko Bridge Replacement Project. This introductory background information is followed by discussion of the urban site constraints, which controlled the foundation type selection for both projects. In closing, the paper discusses the micropile design process, load testing, and construction.VERRAZANO NARROWS BRIDGE HOV & BUS RAMP IMPROVEMENTS BACKGROUNDProject ScopeThe project consists of two new ramps; one designated for HOV / Bus traffic between Staten Island and the Gowanus Expressway, and one to be utilized for storing the barrier transfer vehicle. Also included is the complete reconstruction of Ramps B and F to accommodate horizontal and vertical alignment clearances from the new ramps, removal of the median of the upper level to add one lane, utilities improvements, stormwater improvements, and miscellaneous structural repairs. The new HOV / Bus Ramp was designed for reversible traffic flow to accommodate the demand of the peak traffic direction by movable barrier.Geotechnical / Foundation Engineering ScopeThe geotechnical work included a desk study review of existing plans, geotechnical reports, and geologic maps. This data was subsequently supplemented with a subsurface exploration program. Once completed, foundation design was performed for 25 proposed bridge substructures. Four existing battered pilesupported foundations and two shallow foundations were evaluated for increased loading. Upon completion of the foundation design, foundation plans, specifications, and an engineer’s estimate were prepared. Foundation installation was observed on a part-time as needed basis."

Jan 1, 2016

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972