Search Documents

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before breakage, which appears as heat An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories the romnnred. THE present status of the theory of comminution is extremely unsatisfactory. The amount of various ores and rock products crushed and ground annually approaches the staggering sum of perhaps one half billion tons. Yet the basic concepts underlying an operation of such magnitude are unknown, and actual knowledge of what takes place in comminution is almost entirely empirical. The responsibility for this situation cannot be charged to apathy or lack of appreciation of the importance of the problem. Many attempts have been made to evolve a workable hypothesis, but none has been completely successful. General Considerations In order to break rock, it must be subjected to a stress which strains the rock beyond its critical breaking point. The stress imparts energy to the rock, most of which is released in the form of heat when the stress and resulting strain are removed. If the strain induced exceeds the critical strain, the energy is released by breaking; if the induced strain does not reach the critical point, the energy is released with removal of the stress as energy of resilience. Rock is a brittle material and it is assumed that it breaks approximately at its yield point, so that no permanent deformation results from strains below the critical. When rock is broken the total energy input is accounted for by the heat liberated, and by the surface energy of the new surface produced. A small and probably negligible amount is released as noise. Rock is commonly broken under compression and the applied stress is ordinarily compressive. However, for breakage to occur, it is only necessary that the induced strain exceed the critical value, and this strain may represent the resultant of compressive, shearing, and tensile forces. The stress-strain diagram of rocks under compression, and the modulus of elasticity as determined therefrom, should be fundamental considerations in the development of any theories of rock breakage. Crushing in jaw or gyratory crushers results primarily from a squeezing action, and reduction in a hammer mill is the result of impact. The action in rod and ball mills is a combination of impacting, squeezing, and wearing away by attrition, or rubbing. In ordinary crushing and grinding, the forces are applied at protruding points and are not distributed evenly throughout the rock. This is one of the features of comminution which theoretical considerations have not covered adequately. Another feature is the effect of impact velocities, which may greatly influence the total energy required for breakage. Impact velocities may vary from 1 or 2 fps in crushers to 10 or 20 fps for ball mills, and as high as 100 or more for hammer mills. However, according to the findings of geophysicists, the velocity of sound and of compression waves in stone is many times greater; the primary longitudinal compression waves travel at perhaps 15,000 fps, and the secondary transverse waves, which may reach the surface and cause cracks to form thereon, travel at perhaps 5000 fps. When a crack tip forms, the total surrounding stresses are concentrated in this tip, which rapidly extends throughout the rock particle.1 It would seem that the energy required to deform the rock beyond its critical strain, resulting in the formation of a crack tip, represents practically all of the energy required. Most of the primary crack tips presumably form on the surface. A simple method of designating feed and product size is necessary for the evaluation of crushing and grinding results. Taggart's suggestion2 that the 80 pet passing size be used has been found very practical. In this paper, the square opening screen size which 80 pct of the feed passes is designated as the feed size F, and the size which 80 pct of the product passes, or the product size, is designated as P. The reduction ratio at the 80 pet passing size, or F/P is designated as n. The feed and prod-

Jan 1, 1951

By N. E. Holden, R. R. Goodrich

TheRe is a small area about Murray where bedded gold quartz veins occur in Prichard slate. The ore taken from the upper levels, during the early days, was free milling and was treated by stamp milling and amalgamation. There was likewise a considerable placer working. The report is current that tungsten (scheelite) was encountered, which interfered with the amalgamation in the stamp mills and which, in placering, collected in the riffles in the sluice boxes and clogged them. Consequently, in the quartz mines, the scheelite, when encountered, was rejected, being thrown into the waste, sometimes inside the mine and at other times outside on the dump. The free surface ores became worked out and as the ore in depth became pyritic and rebellious to amalgamation the mines closed down. Last spring tungsten ore brought a high price, near $80 per unit, 60 per cent. W03 and up. This so stimulated the output of tungsten ore that old dumps were explored and waste stored in the mines was gone over. Tungsten was likewise mined from virgin ground. So the district produced quite heavily for a time. The condition now is different. The price is not so high, about $20 per unit WO3, which makes profits questionable when mining in new ground. The accumulations from early day mining have been exhausted and the output has greatly declined. The Golden Chest mine was the heaviest producer of tungsten. The months of June and July were spent at this mine studying the problem. Since the mine had produced both gold and tungsten, we looked forward to the problem of recovering both from what might be called a gold-tungsten ore. A study of the Golden Chest vein showed this was not to be the case. While gold ore and tungsten ore come from the same vein, the tungsten ore is confined to a more or less disturbed or distorted portion

Jan 1, 1918

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

By Spark R. F

The copper deposits at Pernatty Lagoon are predominately djurleite-digenite bodies beneath the permanent water table, and chrysocolla-atacamite-malachite above the permanent water table. The minerals havebeen deposited as sheets, lobes, and pods in zones suggestive of permeability channels or permeability basius with respect to groundwater circulation.Pyrite is deposited in the form of framboids, which reflects its biogenic origin. Copper-iron sulphides deposit by replacement of pre-existent pyrite, and rarely by direct deposition. The latter mode of formation results in complex crustification bandings of chalcopyrite, bornite, sulphur rich bornites, digenite, and blue remaining covellites. The copper-iron sulphides appear to reequilibrate under constrained oxidation, resulting in an iron depletion and associated copper enrichment, the final product of which is a djurleite-digenite assemblage and associated with goethite. Where copper mineralization/ host rock relationships have rendered the rocks entirely impermeable to post ore groundwater movement, then the copper-iron sulphides are preserved as the ore assemblages.Minor and trace minerals observed include sphalerite, carrollite, galena, wittichenite, and possibly tetrahedrite in the primary ores. In the oxidized ores cllprite, tenorite, and trace brochantite have been found.

Jan 1, 1976

By Stephen L. Chryssoulis, Daniela Venter, Stamen Dimov

"Comparative surface analysis of floated and rejected free gold grains from a number of full scale benefication plants and from pilot plant testwork, has shown silver (the most common impurity in gold) and sulphur invariably in greater concentration on floated gold grains, implying that they assisted gold flotation (gold activators). Collector loading measurements on individual gold grains from concentrates of staged rougher flotation tests on a cyclone U/F product of a pyritic gold ore, revealed first progressively lower concentrations of the collector monomer on gold from each follow-up concentrate and secondly a direct proportionality between the surface concentration of silver and the collector monomer. These two observations leave no doubt that silver activates gold and that collector monomers play a significant, previously not fully recognized role in gold flotation.INTRODUCTIONGold to some degree is naturally floatable in industrial systems, which means that it can be recovered without collector addition (Marsden and House, 1992). This is due to the adsorption of hydrocarbons and deposition of sulphur, which are dependent on the metallic properties of gold, particularly its high electrical conductivity, which allows surface electrochemical reactions to occur catalytically and selectively. Cyclic voltammetry has shown that gold can be rendered hydrophobic by deposition of a surface layer of sulphur (Sº) from S2- and HS- solutions (Walker et al., 1984). Twenty monolayers of sulphur were required to produce a hydrophobic gold surface.However, no sulphide flotation plant relies solely on the natural floatability of gold for its recovery. Gold hydrophobicity is enhanced by the addition of flotation collectors such as xanthates (X), dithiophosphates (DTP), dithiophosphinates (DTPI), mercaptobenzothiolates (MBC) etc., as used in sulphide mineral flotation (Dekok, 1973: Adams et al., 1986). The mechanism invoked in enhancing the hydrophobicity of pure gold with the aforementioned four groups of collectors is similar to that of pyrite, whereby collector anions are oxidized at the gold surface to form dimers (Groot, 1987; Marsden and House, 1992; Basilio et al., 1992) As an example, xanthate ions are oxidized at the gold surface to form the neutral dimer dixanthogen (X2):"

Jan 1, 2003

By Charlie Wyche

The British Solomon Islands Protectorate continued developmental work on bauxite deposits on the Islands of Rennell and Vaghena. A feasibility study was completed by Mitsui Mining & Smelting Co., Ltd., and Pacific Aluminum Ltd. (a subsidiary of Conzinc Riotinto of Australia Ltd,), and negotiations with the Government were in progress. The Government will receive a 25% share if the project is realized. It was estimated that the Islands contain 60 million tons of bauxite with an alumina content of 45% to 50%.

Jan 1, 1980

By M. Albertson

At Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 m.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 m.), the width at the lower lobe was about 1000 ft., and the width at the narrows probably 400 to 500 ft. The original depth of water varied from 20 to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the lake. About 1,500,000 tons of mill tailings, composed of sands and slimes, were discharged into the lake's waters previous to 1915. Most of this material

Jan 1, 1921

By Tom Bilson

TO recover the remaining ore tonnages along the south side of the Inspiration orebody, the company began open-pit operations in early 1948 in addition to underground mining. Due to the differences in elevation between the orebody and the existing ore handling and treating plants, the truck haulage operation is up hill. Road grades were established at 7 pct maximum.

Jan 8, 1951

By C. E. Abbott

THE Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production are as follows: Fe2O3 Si02 A12O3 CAC03 MGCO Lump, per cent 0.51 0.22 98.63 0.14 Crushed and washed, percent 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 7 1/2 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1 ¼ to 0.063 in., is calcined at the, lime-burning plant and used for lime charges at the Ensley open hearths.

Jan 1, 1936

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

A philosophy is presented that new graduates in mining and metallurgy should be equipped to use computers during their under- graduate courses, should be aware of the capabilities and costs of a wide range of computing equipment, and should receive sufficient stimulus to become involved in applying computers for the benefit of the mineral industry. A program is presented in which computer applications and "hands on" involvement with computers are integrated into the progressive stages of the undergraduate courses in Mining and Metallurgy. In this respect, the role of the computer is to assist the student by performing time consuming tasks, to demonstrate the industrial applications of computing, to extend the scope and complexity of the tutorial, assignment and project work which can be undertaken by the student, and to provide the essential first stepping stones toward continued useful involvement with computers during the graduate's working life.

Jan 1, 1977

By Yahia M. Al-Smadi

Effect of lateral loading against existing sheet pile wall and distribution of gravity loading due to various number of construction loading scenarios were studied. The objective of this effort was to determine the loading case that permits the contractor to utilize a 400 ton crane at the specified location with the existing limitation imposed on site. Staged analysis was determined as the methodology that will more accurately predict the exiting and additional stress due to the impose crane loading. A reliable and robust analysis (ANSYS) software was used to complete both 2D and 3D finite element model and analysis. Analysis model parameters such as material properties, non-linear behavior of the soil, and meshing are presented and discussed. At the conclusion specific range of crane operation and pick weights operating on existing concrete mat supported on top of an existing tunnel was reviewed and deemed acceptable.

Jan 1, 2010

The purpose of this paper is to outline the current status of financing in the Australian Gold Mining industry and to discuss a number of developments that have occurred during 1983/84.Recognising the importance of equity financing various equity issues, including project valuation, will be discussed against the backdrop of an industry experiencing both rapid growth and a changing structure.Nothwithstanding the current tax exempt status of the industry there is a trend towards more debt financing. A number of financing issues will be covered and it will be shown howvalue can be created through astute financing planning.

Jan 1, 1984

By Hokuichiro Ohmachi

INTRODUCTION Metallic minerals have been formed only through complex geologic processes which took place at certain stages of the earth's histrory. Their concentration, abundance, and distribution are, therefore, restricted geologically, and very small in global scale. Ore is a mineral deposit or mineral concentration from which metals can be economically extracted by the contemporaneous technology. By this definition, several factors should be considered before any mineral deposit is regarded as an ore. The grade of mineral concentration and the scale of the reserve are most important. Demand for the metal and its price are the other factors. Advancement of technology in mining and extraction are also vital. Copper, for example, is now commonly extracted from the ores containing less than 0.3% of the metal. However, in the 1700's the common minerable grade was about 13%, and in the 1900's between 5 to 2.5%. This decrease in minerable grade is a function of not only the demand for copper, but also technological progress in mining and metal extraction in this case. Availability of ores has recently been subject to political factors, which were not the primary concern in the past. The petroleum of the Middle East is the prominent example. The metallic minerals are classified into three categories. The first one is the minerals free from these factors mentioned above. Iron and manganese belong to this category. The second category include aluminum, copper, nickel, cobalt, titanium, lead and zinc. These metals can be provided by the future progress in technology which enables the use of lower grade deposits. The third one represents the metals whose occurrence is geologically limited, and, thus, subject to the political factors. Niobium and tantalium are the example. In this article, I discuss these minerals in detail to give an outline of the factors which brought their concentration, distribution and availability. SELECTED MINERAL CONCENTRATIONS Iron Major iron ore deposits are the features of the relics of ancient continental crusts. They are found in all the continents where the Precambrian rocks expose. They do not occur in the oldest rocks (3,000my old) nor in the youngest ones (600my old). They are sedimentary rocks, normally, exhibiting alternations of bands of iron oxides (magnetite and hematite) or iron silicates (especially greenalite), and bands of silica, variously described as jasper, quartzite and chert. The best known banded iron ore deposits exist in the Lake Superior region of the North America, and their distribution extends at intervals to Labrador of Canada. Other examples occur in the U.S.S.R. Brazil, Venezela, India, the mainland China, and southern and western Africa (Liberia and Guines) (Table 1). Recently large deposits have been discovered in the Hammersley region of the western Australia, and northern and central region of Brazil. These ore deposits were originally formed in shallow seas where simple but abundant life existed. After the deposition, enrichment processes , related to tropical weathering, have brought about wholesale removal of silica to produce the deposits of best quality. Ores with 50-60% iron represent the best products in the Precambrian fields. Since local reserves of this high grade ores approach to exhaustion, benefication processes have been used effectively to upgrade much leaner ores (for example, taconite with 20-25% iron in Minesota, U.S.A.). There are two other types of iron deposits. Ironstone, a sedimentary rock containing goethite, chamosite and siderite, first appeared in early Paleozoic times in the stratigraphic record, and reached its Zenith in the Jurassic. Similar bedded iron deposits are found in the belt from the Cleveland Hills to Oxford in England, and in the "minette" oolitic ores of Alsace-Lorraine in Luxenburg and France. The iron content of these ironstones seldom exceed 30%, but they usually contain calcite and are self-fluxing. They also have phosphorous as undesirable impurity. Because of the grade and impurities, they require more fuel than the Precambrian ores. The third type of iron ore is associated with igneous activity and consists of magnetite and some hematite, and apatite. This deposit is believed to be a product of magmatic differenciation. It occurs in Kiruna of Arctic Sweden. The iron ore, therefore, present no global shortage problem. They extend to considerable depths. Their concentration is largest among the metals. If low grades were treated, the resource can be stepped up much substantially. Manganese Manganese is a ferro--alloy metal, thus, essential to the manufacture of sound steel. Manganese comes from manganese oxide and silicate ores. Many minerals contain manganese, but only a few oxides, silicates, and, in some places, carbonates (rhodecrosite) are mined as ore. Types of manganese deposits are bedded, massive,

Jan 1, 1982

By Hui Wang

With the great increasing use of nickel metal hydride batteries recently, the waste of this kind batteries have been paid for close consideration. For the main reason that the waste of the batteries contained precious metals and lanthanide which cost great lose. This paper introduces the pyrometallurgical process of recovering nickel and cobalt from the waste of the nickel metal hydride batteries. Particularly, the waste for the process was from factory during the producing program. The use of designed solvent to divide nickel and cobalt in melted state from the waste is described. Also, the result of the nickel and cobalt and melted gangue that mainly consist of lanthanide oxide are included in details. The aim of the paper is to find out a simple and feasible way to reuse waste from nickel metal hydride batteries.

Jan 1, 2009

Discussion of the paper of, RICHARD H. RICE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 89, May, 1914, pp. 721 to 743. S. G. VALENTINE, Oxford, N. J.-In a paper read at the New York meeting of the Institute last February I presented some notes taken from our experience with the turbo blower operating on a blast furnace. In connection with Mr. Rice's very interesting paper there are a few items that might be of further practical interest. The question of the reliability of this type of blower will naturally be presented. In this connection we would say that our turbo blower has been in practically continuous use during the present blast, which was begun June 7, 1912, with only three interruptions for repairs of any consequence. Soon after blowing in there was developed a tendency of the blower to surge or pulsate. This occurred on operating at a point considerably below the normal capacity of the machine, and was checked with comparatively little trouble by throttling the intake slightly and taking up a small lost motion on the governor connections, a legacy of the previous blast that had not been attended to. All this required only a few hours' time. In. March, 1914, the furnace being banked on account of a blizzard that cut off our freight deliveries for five days, the opportunity was used to replace the carbon packing on the steam-turbine shaft and to repack the steam inlet valves. In June, 1914, the blower was off 8 hr. to replace an oil ring and scrape a bearing. With these exceptions we have made continuous use of the machine and find we can depend upon it with entire safety as a piece of machinery.

Jan 4, 1915

By Lix Tafur, Julio Gómez, Vidal Aramburú

Las operaciones de la pequeña minería artesanal de oro se caracterizan por tener bajas recuperaciones, bajo condiciones inseguras de trabajo y consecuencias negativas en el ecosistema por el uso indiscriminado del mercurio y/o cianuro, Con la finalidad de mejorar dicha práctica se desarrollaron pruebas de lixiviación con reactivos alternativos al cianuro para recuperar oro y plata a partir de los relaves de amalgama. El análisis mineralógico determinó la presencia de especies como: oro, pirita, magnetita, hematita, Ilmenita, rutilo y gangas, así mismo los ensayos químicos determinaron una ley de 20.16 g-Au/TM, 147.12 g-Ag/TM y 10.53 ppm de Hg

Sep 29, 2023

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970

By P. Au, R. Kearsey, D. Y. Seo, Patnaik. P. C.

Three nickel based superalloys (7.5%Cr+5%Co+2%Mo+1%Ti+5%Al and Ni balance (wt%)) containing different amounts of W and Re were produced in the single crystal (SX) condition utilizing the Bridgman casting process. First, the effect of different levels of Re, and W on chemical microsegregation were investigated by EPMA quantitative analysis, and eutectic phase fraction analysis. Second, in order to investigate the effect of these refractory elements addition on oxidation behaviour, isothermal oxidation testing of the SX nickel based superalloys was conducted at 1000°C for 277 hours under 3 ppm moisture content of air in a thermogravimetric analyzer (TGA). All three SX nickel based superalloys revealed an excellent SX solidification structure with a common primary dendrite arm spacing of -250 µm and a large fraction of ?/?' eutectic located between the secondary dendrite arms. From the average EPMA compositional results, with the exception of Ni, elements such as Cr, Co, Re, Mo, and W all tended to segregate towards the dendrite core during solidification, while Al, Ti, and Ta were present in greater quantity in the last liquid phase to solidify, which resulted in large eutectic ?/? ' phases to form within the interdendritic regions. As the nominal level of Re increased, microsegreagation of Re, W, Cr and Mo increased, indicating that Re had a much greater influence on partitioning behavior compared to W. Figure la shows the specific mass gain as a function of exposure time for each alloy. An alloy with 2wt% of W and Re (Alloy B) exhibited less weight gain compared to two other alloys with either higher content of W or Re (Alloy A and C). Microstructural and compositional analyses of oxidized samples were conducted using SEM and EDS. Figure lb shows the typical surface morphologies of the oxidized Alloys A and B. It is evident that more oxide nodules (indicated by arrows in the figure) were presented in Alloy A. It is speculated that the amount of these nodules was responsible for more mass gain in Alloy A compared to the two other alloys. From the examination of the longitudinal section of the oxidized samples as shown in Figure 2, for Alloy A, nodules actually penetrated deep into the material. For Alloy B, however, a relatively uniform and continuous oxide layer was developed and deeply attacked areas were not observed. It was also found that preferential oxidized regions were located at the area between the ?/?' eutectic phase and the dendrite arms where the concentration of refractory elements was relatively high. Therefore, it is plausible that the oxidation kinetics of these alloys is related to the extent of microsegregation.

Jan 1, 2004