Search Documents

HAVING previously shown you how ores are found and mined, and also how they are prepared and disposed for smelting, and then how the blast furnaces and other furnaces are made for purging their earthiness, all this would be as nothing if I did not proceed to show you the method of smelting them. Therefore, in the present chapter I wish to show you how you must proceed in this very important operation, telling you all I have seen and also how much work with this kind of blast furnace I have done or directed. For this reason I tell you first to take by weight or measure the quantity of ore that you wish to smelt and, particularly if it is a kind that contains silver, break it into small pieces about the size of [52v] beans. If the ore had previously needed evaporation by fire or cleaning by washing, you will have had this done well and have had it properly prepared by a master sorter or others. A layer of this is arranged on a bed of planks, bricks, or flat stones in front of the blast furnace and its companion is placed on top, then a quarter part of galena or a third if you can obtain it. Then an equal part of crushed iron slag or slag from the same or different ore is added. These materials are spread in layers one above the other. When the blast furnace has been constructed as taught above, correct in all its parts, and is full of well-kindled burning charcoal, then fill it up with charcoal and admit water to the bellows machine. When you see that it is well kindled again from this wind and that the flames begin to come out forcefully on top, work it down with a little rake and fill it up again. Then the pannier is filled with new charcoal, the blast furnace heaped full, and another basketful of the said composition of ore is also put on top. Proceed in this way, continually adding charcoal and ore as long as you have any, or as long as you wish to keep up the work, maintaining the blast furnace always full, or continuing in this way until the bottom of the blast furnace is filled with melted materials. Decide this by judgment, or by seeing through the mouth of the tuyère where the wind of the bellows enters that they are level with this. Then with an iron tool open the hole that was left as an outlet in front of the blast furnace and allow all the metal with its slag to run out. These two things, flowing through the chan-

Jan 1, 1942

By E. R. Buchanan, R. E. Reed-Hill

Cylindrical magnesium single crystals were deformed in torsion. The axis of torsion was the basal pole. Five crystals were deformed to different strains between 0.08 and 1.03 and then sectioned in order to determine their dislocation densities using the transmission electron microscope. The work hardening rate of all specimens was at least an order of magnitude higher than that normally associated with easy glide in a tension test and comparable to that obserzed in stage B of a tension test. The correspondence between stage B in a tension test and the initial stages of a torsion test is believed to result from the fact that in both cases deformation occurs in a structure containing roughly equivalent densities of the dislocations associated with the three basal slip vectors. THERE are three basic ways of changing the shape of a crystal using slip dislocations. The crystal can be sheared along a slip direction in a slip plane; it can be bent about an axis in the slip plane normal to the slip direction; and, if the slip plane contains multiple slip directions, it can be twisted or rotated about the slip plane normal. Of the three processes, generally known as translational, flexural, and rotational slip, only rotational slip has not been extensively investigated. The object of the present research was to obtain basic information about this phase of crystalline plasticity. This paper is concerned with some aspects of the stress-strain curves obtained by twisting magnesium crystals about their basal poles. Magnesium was selected for four reasons. One, its recovery rate at room temperature is relatively low. Two, single crystals may be easily grown. Three, at room temperature the critical resolved shear stress for basal slip is about two orders of magnitude lower than that for nonbasal slip, so that rotational slip might be expected to occur primarily by basal slip. Finally, relationships between flow stress, shear strain, and dislocation density have been determined for tensile deformation of magnesium crystals,' thereby providing a basis of comparison for the torsional results. EXPERIMENTAL PROCEDURES Crystals were grown from 0.5 in. diam extruded sublimed magnesium rod furnished by the Dow Chemical Co. who reported that it contained in weight percent less than 0.0003 Al, 0.01 Ca, 0.01 Cu, 0.0012 Fe, 0.001 Mn, 0.0005 Ni, 0.003 Pb, 0.001 Si, 0.01 Sn, and 0.02 Zn, with the balance magnesium. All crystals were grown in a dried argon atmosphere using Jill-son's2 modified Bridgman technique. Two different methods were used to obtain crystals with the basal plane normal to the specimen axis. These included direct growth from seeds of the proper orientation, and spark machining (trepanning) of 0.5 in. diam cylinders from larger (1.5 in. diam) randomly grown crystals. The crystals thus produced were polished in a 20 pct HC1 water solution and then etched in a 1 pct HC1 water solution to develop etch pits lying in rows parallel to the basal plane trace. The crystals were then revolved about their axes on the stage of a low-powered microscope. Torsion specimens were prepared only from those crystals whose axes were normal to the rows of etch pits. It is estimated that this simple orientation method was accurate to about 51 deg. 1.625 in. long cylinders were next cut from these selected crystals and then acid machined in a 20 pct HC1 water solution into torsion specimens with a 1 in. long by 0.30 in. diam reduced gage section. Following this, they were annealed in air at 400°C and furnace cooled to room temperature. The specimens were given a final polish in a 10 pct HC1 water solution, rinsed in ethanol, dried, and cemented into brass grips with an epoxy resin. In addition to the torsion specimens, several tensile specimens with their basal planes at 45 deg to the stress axis were also prepared with similar dimensions except that the gage sections were increased to 4 in. in length. The torsion specimens were tested in the apparatus

Jan 1, 1970

By Randal J. Barnes

Computer based techniques for solving the Ultimate Pit Limit Problem have appeared in mining literature since the early 1960's. The majority of papers pertaining to this subject can be partitioned into one of two categories: discussion of the pros and cons of a particular algorithm, or a case study presenting specific applications of an algorithm. Subsequently, there has a1 so been considerable debate concerning the best techniques between, essentially, two camps: those favoring the moving cones techniques, and those favoring the techniques which yield true optimal pit designs. The purpose of this paper is not to add to this debate, but rather to present a few new ideas (partially a new look at an old idea), which can be easily implemented to noticeably improve any ultimate pit limit approach independent of the particular algorithm used. These ideas fall under the heading of "bounding the optimum" (Barnes and Johnson, 1980).

Jan 1, 1982

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By P. Seppanen

Cemented fill was first introduced at the Keretti mine in 1952, but entailed high cement costs, the need for stope preparation, slimes handling, clean-up and maintenance, increased mine dewatering, segregation of fill and long setting times. In the 1970s research began into the use of iron blast-furnace slag as a binding agent and by 1989 Pyhasalmi, Vihanti, Keretti, Vammala and Enonkoski had saved US $11 000 000 by using slag binders instead of cement. Viscaria in Sweden and Tara in Ireland also use slag as 90-100% of total binder, although their backfilling methods vary. The main area of interest in slag research is determining the activation methods for initiating the binding reactions; it is also important to achieve other characteristics such as resistance to corrosion by sulphuric ion. New backfilling techniques developed during the 1980s included the use of high-density cemented tailings fill at Vammala and porous cemented rockfill at Enonkoski and Viscaria. Future developments focus on concepts such as integration of mining and milling with backfilling and the achievement of total underground disposal of wastes

Dec 1, 1995

By C. T. Twort

As technology and economic conditions allow mines to operate at ever greater depths, increasing demands are placed on the environmental engineer to adjust the capacity of the installed mine . - refrigeration systems. At the same time the engineer must satisfy the changing legislation, which demands that developments are carried out in as an energy efficient and environmentally accept- able manner. Following the trends outlined above, this paper is written to give an overview of the current and potential future refrigeration technology available to the mining industry. The effects that may be produced by the adoption in mining applications of the new generation of 'green' refrigerants are examined both at the design stage and when considering the viability of retrofitting existing systems so that they comply with the Montreal Protocol. An introduction to the concept of Total Energy Warming Impact (TEWI) is provided, with an explanation of its use in optimising system design and performance, and its incorporation as part of an environmental audit strategy. The paper concludes with a discussion of innovative refrigeration techniques and the possible future developments in legislation.

Jan 1, 1997

By B. Howerton, M. M. Matlock, D. A. Atwood

In the Gold-Cyanide Process (GCP) the cyanide anions act to solubilize the gold and silver present in the ore, and mercury as well. The resulting mercury and cyanide rich effluent are serious health and environmental problems. Currently, there is no mercury treatment from the ore leach solution since there are no precipitating agents or other technologies which can be used effectively in the pH ~ 10solutions. Recently, however, we have developed a new chelate ligand that is impervious to this level of pH and it can be used to precipitate Hg from NaCN solutions. On an actual sample taken from an active gold mine the chelate selectively reduced the mercury level from 34.5 ppm to 0.008 ppm within 15 minutes. Importantly, the gold and silver levels remained unchanged throughout this process. Thus, the environmental impact of Hg released in the GCP can be drastically reduced. Moreover, with a mercury treatment technology now available it may be possible to change, or reinvent, the entire GCP process.

Jan 1, 2003

By James C. Franklin

Companies are constantly searching for more effective methods of controlling and reducing costs. In recent years increased emphasis has been placed on cost reporting to the middle manager and down to the first-line foreman because this is the place where the money is really spent. Traditionally, operations management has been relegated to using cost systems designed by financial management for the use of financial management. They reflect the machinery necessary to produce profit and loss statements, and so-called cost reports emanating from these systems frequently have a heavy orientation toward product costing rather than the cost that an individual manager or foreman actually controls. In addition to direct operating costs by function or product type, they often include overhead allocations from local operations as well as from the home office. This type of full-absorption costing has many worthwhile uses but is of little or no use to operations management for cost control purposes. It is particularly discouraging to many supervisors because it includes so many categories of cost over which they have little or no control. It is for this reason that modern, aggressively managed companies are increasingly moving in the direction of responsibility cost reporting. It is the objective of responsibility cost reporting to report only direct operating costs over which the individual manager or foreman has complete control, thus facilitating cost control by fixing responsibility for cost.

Jan 1, 1979

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By John G. Hall

The pumping operations at the Chief mine have been unique in the respect that for many years the entire flow of water into the mine has been disposed of by pumping into natural underground "caverns" or "sinks." Volumes up to 4000 gpm have been pumped into these caverns with no apparent tendency for the caverns to fill with water, and it has never been proven that any of the water returns to the mine workings. Major pumping operations have been carried on during two periods, the first from 1918 to 1927, and the second from 1942 to the present time. Early Pumping Operations CHIEF MINE The Chief Consolidated Mining Co. was organized in 1909, and for the following nine years ore was developed and mined from the 600 level down to the 1800 level, all above the permanent water table, the 1820 level. The ore occurs as extremely-irregular pipes of replacement ore in limestone, and to date a total of approximately 2 1/2 million tons of ore has been produced. The ore was highly oxidized down to the permanent water level, and some highly-oxidized ore runs occur beneath the permanent water table. In 1916, with extensive mining being done on the 1800 level, 20 ft above the water table, there were indications that a zone of secondary enrichment might exist below the water, and in order to follow the ore runs to greater depth, it was realized that arrangements would have to be Made to pump water to the surface. The original pumping installation was designed to pump 350 gpm in five stages against a 1900-ft head to the surface. By January 1919, the water had been lowered to the 1900 level and an excellent grade of silver-lead ore was being produced from the zone of secondary enrichment. At this point. the flow of water equalled the capacity of the pumps, and pumps of an additional 1000 gpln were installed to supplement the original system. By January 1920, the water had been lowered approximately 100 ft, and the total flow of water was 1000 gpm. The water was being pumped from many different places in the mine where ore was being followed downward, with 27 different pumps operating below the 1800 level, mainly Cameron air-driven sinker pumps. These first sinking pumps were cumbersome and inefficient, and each of the larger pumps weighed approximately three tons and required tremeridous volumes of compressed air. During this period, an exploration drift being extended north and west from the Chief shaft on the 1600 level encountered a large natural cavern some 2000 ft from the shaft. This cavern in places measured 60 ft in diameter. Sometime later the disposing of water into this cavern was suggested, and as an experiment to determine the results of such an operation, an attempt was Made to fill the cavern by pumping in a small volume of water, but the water disappeared as fast as it was discharged into the cavern. It was decided then to try the cavern as a drainage outlet for the entire volume of water being pumped to the surface, and the water apparently did not return to the mine workings. Subsequently water up to 3000 gpm was pumped into this cavern. An attempt was made to determine whether any water was being returned from the cavern to the lower workings, and 100 lb of sodium fluorescein salt was added to the water discharged into the cavern, but no trace of it was found in the drainage water in the mine. Results of another such test will be described later.

Jan 1, 1950

By A. M. Stone

Following the conceptual idea of a Continuous Elution Process early in 1982, the system was successfully pilot plant tested at Western Mining's Kambalda gold plant in December 1982. As a consequence of these tests the Ok Tedi elution ciruit design was changed from batch operation to continuous operation resulting in a reduction in the number of similarly sized elution columns from five operating with one standby to one operating with one standby and halving the process steam requirements. In addition to providing significant capital and operating cost savings the continuous process was simpler to operate than the batch process.

Jan 1, 1989

By Joseph B. Story, John T. Clarke

A modification, of the Kelvin bridge using an inductor was used to measure the conductivities of molten sodium chloride, calcium chloride, and mixtures thereof. A capillary-type four-lead fused quartz dipping cell was constructed. The effect of a small amount of potassium chloride on the conductivity of the melt was determined. IN the electrowinning of sodium and chlorine from sodium chloride in Downs cells, calcium chloride is added to the sodium chloride in an approximately equimolar amount to permit cell operation at a lower temperature. This lower temperature improves current efficiency and ease of operation, but decreases voltage efficiency by decreasing the electrical conductivity of the melt. A knowledge of the electrical conductivity of the Downs cell melt is necessary to the understanding of Downs cell operation, for the IR voltage drop across the melt is responsible for a significant part of the electrical power consumed by the cell. The work of previous investigators on fused sodium chloride-calcium chloride mixtures was reviewed from the standpoint of consistency with the results of others on the conductivities of the pure constituents. The electrical conductivity of pure fused sodium chloride has been established with accuracy by Van Artsdalen and Yaffe,1 by Edwards, Taylor, Russell, and Maranville,2 and by Lee and Pearson.3 It has also been studied by a number of other investigators.4-13 The best values for calcium chloride are believed to be those of Lee and Pearson,3 since the sodium chloride and potassium chloride conductivity values given by them check the best literature values. A number of other investigators have also reported values for calcium chloride.'-"."' Electrical conductivity data for fused sodium chloride-calcium chloride mixtures have been reported by Sandonnini,12 Vereshchetina and Luz-hnaya,18 Ryschkewitsch,11 Barzakovskii,5 and Alaby-shev and Kulakovskaya.15 Sandonnini reports no data at temperatures lower than 850°C. The conductivity values reported by Vereshchetina and Luz-hnaya, by Ryschkewitsch, and by Barzakovskii for pure sodium chloride and for pure calcium chlor- ide vary somewhat from the literature values believed to be best and the sodium chloride-calcium mixture data of these authors and of Alabyshev and Kulakovskaya (who give no data for the pure compounds) show significant variations. In view of these facts, it seemed that an investigation of the electrical conductivities of fused sodium chloride-calcium mixtures would be worthwhile. Apparatus Bridge System—The bridge used,in this investigation is diagrammed in Fig. 1. In general, the elaborations of this bridge over the simple Wheatstone bridge were for the purposes of a) eliminating lead resistances or making them accurately measurable, and b) eliminating major capacitative and inductive effects or balancing them against each other. Lead resistances in the lower arms of the bridge were kept as low as possible by making the leads short and of low resistance wire. This could not be done in the cell arm of the bridge because of the remoteness of the cell from the other bridge components and because of the high-resistance nickel or chrome1 wires used in the cell. Since maximum sensitivity is attained when the resistances of the four arms of the bridge are equal, 50-O resistors were used in the lower arms of the bridge when fused salt conductivities were being measured, and 1000-O resistors were used when the cell was being calibrated with normal aqueous KCl solution. The cell resistance was of the order of 50 ohms with fused salts and of the order of 1000 ohms with normal aqueous KC1 solution. The resistors used were non-inductive and accurate to 50.05 pct (General Radio Co. Types 500-C and 500-H). The lead resistance between point A in the cell and point E at the measuring resistor was eliminated by using the kelvin bridge principle; that is, the voltape drop across the lead from point A to point E was divided between the cell arm of the bridge and the measuring arm of the bridge in proporation to the resistaxes in the lower arms of the bridge.

Jan 1, 1958

A test model is presented for the simulation of dewatering by gas injection of a porous aquifer above longwall workings. A finite difference model used in the oil industry was modified to match the underground mining conditions. The model is suitable to cope with the problem of dewatering reservoirs of low transmissivity. After comparing more versions, it has been concluded, that the investigated dewatering method can be proposed under special hydrogeological conditions only.

Jan 1, 1988

By Pasi Latva-Pukkila

Underground rock drilling has gone through intense development during the last 25 years. Mechanization and hydraulics have greatly increased the efficiency of drilling and improved the environment of the drill operator. As the total economy has become more and more important, the development has resulted in greater overall economy in drilling. The latest evolution step is computerization of drilling equipment. Computerization has been applied to tunnelling jumbos, long- hole drilling rigs and bolting rigs. With today's technology computerization is the natural way to increase capacity and productivity of the drilling process. However, it is still impractical to implement total "robotic" drilling. In computerized drilling the operator's role continues to be vital in controlling the drilling process and in analyzing the effect of individual parameters on the whole excavation process. Today this is called "CAD" - Computer Aided Drilling.

Jan 1, 1989

By Marco A. Ramírez-Argáez

A 2D mathematical model was developed for the plasma arc welding process. Computational simulations based on mass and momentum conservation equations as well as Maxwell equations were performed by using the commercial software PHOENICS. The model predicts the electric characteristics of the arc column, flow patterns, temperature contours and electrical potential, by varying the composition of the cover gas, in this case, argon and nitrogen. It was found that an arc of nitrogen with respect to one of argon generates more intense jets, greater voltages, and lower temperatures in the arc column for welding arcs current of 150 A and 10 mm arc length.

Oct 30, 2017

By B Mohanty, Y C. Lizotte

Optimization of blast fragmentation in underground hardrock mining requires analysis of its effects on loading and haulage equipment, together with the downstream materials handling system, with the objective of minimizing total mine operating costs. A methodology is reported which has been developed to quantify the actual fragmentation and equipment performance in the field. This is data which has seldom been practicable to capture nor received serious attention in mines. Based upon the experience gained in underground studies, a prototype standard is proposed which aims to summarize the pertinent data, collection and analysis for fragmentation assessment. This relates to parameters of direct measure, such as mean size and distribution, as well as muckpile and work environment. The paper concludes by defining the impact of fragmentation on the loading and downstream handling system.

Jan 1, 1991

By David Baker

A Discussion of the Paper of David Baker, read at the Lake Superior Meeting, September, 1904. (Washington Meeting, May, 1905.) MR. JOHN J. PORTER, Chicago Ill. (communication to the Secretary*) :-Mr. Baker's account of his experiences with stock-distribution has been particularly interesting to me, as it confirms the opinions which I had formed concerning the rapid failure of linings in several furnaces that have recently come to my notice. These furnaces, four -in number, are of modern construction, having been built or remodeled within the past two years, and are equipped with a well-known type of skip-hoist and double-bell charging-apparatus. In every case, a hot spot has developed within a few months after blowing-in, which has already compelled relining in two cases, and the probabilities are strongly against a long campaign in the other two. Since the hot spot in each case appeared in a position approximately opposite to the skip-hoist, and since the sizing, mentioned by Mr. Baker, is very apparent, it would seem as though there could be no doubt concerning the cause of the trouble. Nevertheless, there are some who cannot see it in that light; for the managers of two of these plants, at least, do not admit the existence of bad distribution, and have satisfied themselves by putting in cooling-plates, thickening the lining of the in-wall, and changing the brand of the fire-brick used for the construction of the walls. From observations of the clumping-action of the skip-hoist, and from subsequent inspection of the stock-distribution in the furnace itself, I arrived at the conclusion, some time ago, that no system of filling could be perfectly satisfactory where the stock is dumped into the hopper from one side, also that some

Mar 1, 1905

By A. Lee Barrett

THE Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting with this report the first of a series of cost comparisons which it plans to present to the Institute. The plan is to assemble maintenance cost on all equipment connected with mechanical operations at the face of coal mines, to arrange these costs by districts, to make comparisons between districts, and within districts. This particular report covers data with respect to mobile loading machines, including both "on-track" and "off-track" equipment. It is anticipated- in-fact, considerable data have already been accumulated-that next year complete maintenance costs by districts can be presented for complete loading units, including the various classes and combinations of on-track and off-track equipment. Data have also been collected with respect to some phases of maintenance methods and certain recommendations of the committee are included dealing with maintenance problems. In the assembly of these data more than 120 questionnaires were sent to operating companies through- out the United States. At the time the report was written 33 questionnaires had been returned with completed information and an additional group of companies had written that the information requested was not at present available but that they hoped to have such information available in the not far distant future. The replies as

Jan 1, 1946