Search Documents

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method. CONSIDERING the subject alone, this paper would cover only a mechanical treatise of pillar roping. Because the St. Joseph Lead Co. originated the practice, it is proper to give a short introduction to the company. It is also proper to describe pillars and discuss their purpose to justify expending large sums of money to preserve them after the surrounding area has been thoroughly mined. Because the St. Joseph Lead Co. originated the practice of back pinning with wedge bolts, patch plates and channel irons, and the pouring of substitute pillars of concrete, these too, are mentioned. The Southeast Missouri Division of the St. Joseph Lead Co. is the largest lead producer in the United States. About 95 pct of the present producing mines are in St. Francois County, which begins 60 miles south of St. Louis. The entire lead ore production of this county, at the present time, is mined and milled by this company, treatment plant capacity being about 22,000 tons per day. This area is also the oldest, lead having been mined at Mine La Motte, in Madison County, in 1723. Estimated production of all the various companies that have mined here is about 7,000,000 short tons of pig lead. Method of Mining The lead occurs in the ore as galena. Galena is found either in the form of disseminated or solid streaks, of varying thickness. Ore stratum is the Bonne Terre dolomite, which is about 350 ft thick, but almost all the ore is in the lower 100 ft. Ore is mined by room and pillar method in open stopes. These stopes vary in height from 7 ft to 200 ft, depending on the thickness of the pay ore in that spot. Back, or roof, is supported entirely by pillars. In a majority of stopes, after the loose scales are mined down, the back has remained solid for many years (fig. 1). Under ideal conditions pillars are spaced to form an equilateral triangle and are as small and as far apart as the height of the stope and the character of the back will permit. They vary in diameter from 10 ft to 50 ft and are from 18 ft to 50 ft apart, measured from the outer edges. In general, the pillars are approximately 12 ft in diameter, and 25 ft apart. The spacing is very uncertain because of the vagaries of the ore trend, the desire to better support breaks in the back, and the attempt to spot out the thinner ore by not placing one in the core of the ore body. Use of Structural Steel Channels In stopes where the back is bad because the overlying formations are thin with wet, weak and shaly

Jan 1, 1951

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method. CONSIDERING the subject alone, this paper would cover only a mechanical treatise of pillar roping. Because the St. Joseph Lead Co. originated the practice, it is proper to give a short introduction to the company. It is also proper to describe pillars and discuss their purpose to justify expending large sums of money to preserve them after the surrounding area has been thoroughly mined. Because the St. Joseph Lead Co. originated the practice of back pinning with wedge bolts, patch plates and channel irons, and the pouring of substitute pillars of concrete, these too, are mentioned. The Southeast Missouri Division of the St. Joseph Lead Co. is the largest lead producer in the United States. About 95 pct of the present producing mines are in St. Francois County, which begins 60 miles south of St. Louis. The entire lead ore production of this county, at the present time, is mined and milled by this company, treatment plant capacity being about 22,000 tons per day. This area is also the oldest, lead having been mined at Mine La Motte, in Madison County, in 1723. Estimated production of all the various companies that have mined here is about 7,000,000 short tons of pig lead. Method of Mining The lead occurs in the ore as galena. Galena is found either in the form of disseminated or solid streaks, of varying thickness. Ore stratum is the Bonne Terre dolomite, which is about 350 ft thick, but almost all the ore is in the lower 100 ft. Ore is mined by room and pillar method in open stopes. These stopes vary in height from 7 ft to 200 ft, depending on the thickness of the pay ore in that spot. Back, or roof, is supported entirely by pillars. In a majority of stopes, after the loose scales are mined down, the back has remained solid for many years (fig. 1). Under ideal conditions pillars are spaced to form an equilateral triangle and are as small and as far apart as the height of the stope and the character of the back will permit. They vary in diameter from 10 ft to 50 ft and are from 18 ft to 50 ft apart, measured from the outer edges. In general, the pillars are approximately 12 ft in diameter, and 25 ft apart. The spacing is very uncertain because of the vagaries of the ore trend, the desire to better support breaks in the back, and the attempt to spot out the thinner ore by not placing one in the core of the ore body. Use of Structural Steel Channels In stopes where the back is bad because the overlying formations are thin with wet, weak and shaly

Jan 1, 1951

By W. N. Lacey, B. H. Sage

In recent years there has been an increase of interest in the flow of gases at relatively high pressures. Hydrodynamic calculation of the energy losses in the flow of gases in conduits, as well as through the porous solid materials constituting natural petroleum reservoirs, requires a knowledge of the viscosity of the fluid at the pressure and temperature involved. Although there are numerous publications concerning the absolute viscosity † of hydrocarbon gases at atmospheric pressure, there appears to be little information available relating to the effect of pressure upon the viscosity of these gases. Voge133 determined the viscosity of methane at 32° F. and atmospheric pressure. His measurements at 32° F. were later substantiated by the measurements of Rankine and Smith20 at 63° and 212° F. Ishida14 also reported values for the viscosity of methane at atmospheric pressure. Trautz and Kurz30 measured the viscosity of propane at atmospheric pressure, from 83° to 530°F., by the use of a short capillary tube. Rap-penecker2' determined the viscosity of gaseous isopentane at elevated temperatures. Day6 made an accurate investigation of the effect of pressure upon the viscosity of n-pentane and isopentane at pressures from 2 lb. per sq. in.‡ to the vapor pressure at 77° F. (approximately 9.8 and 13.3 lb. per sq. in., respectively). Earhart7 reported data upon the viscosity of several natural gases measured by the long capillary-tube method. The viscosity of air, at atmospheric pressure and 73.4° F., was measured by Harrington9 by the rotating-cylinder method. Kellstrom15 has rec,ently made an elaborate investigation of the viscosity of air at atmospheric pressure. The latter work is perhaps the most accurate investigation of the viscosity of a gas that has been made.

Jan 1, 1938

By Freeman Bishop

The tight electric power supply is one of the most dramatic problems facing the mining industry in 1971. This is caused by rising demands for energy. Clean-fuel and air-pollution controls have contributed to the problems of producing energy from sulfur oil and coal. Coking coal has become scarce. One stimulating development is that coal is no longer the cinder in the mining industry's eye. In fact, it may be the favorite candidate as a base for fuel within a few years. Synthetic gas from coal is the watchword. In dedicating a multi-million- dollar project aimed at converting coal into oil and gas, Hollis M. Dole, Assistant Secretary of the Interior, recently made it clear that coal, which has been taking a back seat to nuclear fission research and study grants, is now coming into its own. Conversion pilot plants are being activated in all parts of the nation.

Jan 1, 1970

By Joseph E. Pogue

Price is a complicated concept, for price is both a cause and an effect. This reciprocal aspect is commonly overlooked and the oversight is the source of many economic maladjustments. Price is the resultant of the ratio between supply and demand, but it differs from a mathematical concept of a proportion, by itself constituting an economic force which continuously alters the elements that determine the relationship. Price, therefore, is not merely the outcome of other forces but is in its own right one of the most powerful of economic agents. Price accordingly does not play a passive role; nor can it be sterilized or rendered inactive. In consequence, price cannot be fixed or at least kept fixed, except by the elimination of all freedom of choice on the part of producers and consumers. A primary objective of all economic activity is equilibrium. The same is true of a unit of economic activity, the single industry. The plane upon which equilibrium centers may shift in the course of time, but equilibrium itself is the point of departure and the point of return. If an industry is in equilibrium, that industry is operating effectively. The motivating forces of an industry—profits or the common good—are not to be confused with the prerequisite of equilibrium, but this mistake is often made. The producer is dominated by the profit motive; the consumer, or his collective representative, by the general welfare motive. No one is the advocate for equilibrium; that status is supposed to be arrived at automatically. If the forces of competition are perfectly free, such is the tendency. Equilibrium For the purposes of this analysis, equilibrium needs to be broadly defined and is conceived to involve: (1) balance between supply and demand; (2) internal equipoise amongst the elements within an industry; and (3) symmetry in respect to the whole economy. This definition implies flexibility and case of adjustment; a ready accommodation to change. Equilibrium does not postulate profits or nonprofits, social objectives or the lack of them. A decadent industry may be in equilib-

Jan 1, 1937

By J. E. Smith, P. B. Crawford, B. L. Laudrum

A method is presented by which the displacement efficiency of a steam-injection process may be determined. The method consists of a determination of the position of the steam front at a particular time and the application of the Buckley-Leverett theory to the hot and cold regions of the reservoir with the appropriate hot or cold fluid properties. A uniform, linear flow system is assumed for this study. The method is applied to a number of reservoir conditions. The primary properties which affect the results of a steam-injection process are the oil viscosities at steam and reservoir temperatures, injection rate, pay thickness and oil saturation. The efficiency of steam injection is compared with that of water injection for a 10-acre, linearly flooded reservoir. In reservoirs where the oil viscosity is about 35 times the water viscosity, the steam process yields recoveries about 20 per cent higher than the water flood. Where the oil viscosity is near 500 cp, the steam process may recover from three to four times as much oil as a water flood. INTRODUCTION In a previous paper,' a method was suggested for evaluating a steam-injection process. Emphasis was placed upon the determination of the steam-front position in the reservoir at various times. In the present paper, the displacement process is studied in more detail. The approach is essentially that employed by Jordan, Rayne and Marshall3 in their study of hot-water injection. The steam-injection process is quite complex, and an exact description of the process has not been found; however, a qualitative description can be made. When a quantity of steam is injected into a relatively cold reservoir, the leading edge of the steam front continaally flows into cool sand, and some steam condenses. As more and more steam condenses, a bank of condensed water will form which is augmented by displaced connate water. The reservoir may be divided in three regions—(1) a region containing displaced fluids at reservoir temperatures, (2) a region contain- ing water at reservoir temperature and (3) a region occupied by steam. The reasons for the lack of a region of hot water or oil of any appreciable size have been discussed.' A method has been presented by which the location of the steam front can be determined even when heat losses to the regions surrounding the reservoir are sizable compared with the amount of heat injected. It remains to show the effectiveness of steam injection in increasing the ultimate oil recovery. To illustrate the technique for determining the increase in displacement efficiency and, hence, the increase in ultimate production, two sets of hypothetical reservoir conditions will be studied in detail.

Circuit alterations and adoption of more compact items of equipment have made it possible to increase the capacity of the King Island Scheelite concentrator, both with regard to head grade and feed tonnage, while at the same time increasing total recovery and reducing maintenance costs. The present operation is described, with particular emphasis being placed on alterations made during the last two years to achieve capacity Goals.

Jan 1, 1977

By John A. Church

The operations of the Tombstone Mill and Mining Company, in Arizona, have been extensive and interesting; and I will eudeavor to describe what is novel in their work, without attempting to go over the well-known facts of silver milling, concentration and smelting which are the general branches of their business. Their mines are at Tombstone, and their mills at Charleston, ten miles distant. The ore has been mined only above water-level, and at first was

Jan 1, 1887

By D. J. Dollhopf

The objective of this five year study was to investigate the means of establishing non-polluted ground-water and root zone systems in areas where surface mining intercepts physiochemically unsuitable overburden materials. Overburden may need to be sampled on a 60 m grid in order to delineate materials unsuitable for reclamation and to accurately implement selective handling operations. Unsuitable overburden materials were buried successfully in a dragline operation with a minimum of delays, but costs were increased 12 to 53%. After three years the buried material remains above the reestablished aquifer and below the root zone. Construction of a clay cap over the buried material may not be required in semiarid environments. It was shown that some unsuitable overburden materials do not have to be special handled. When inhibitory material constituted <5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile due to mixing/dilution processes. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. At least a portion of the postmine aquifer had hydraulic conductivity rates lower than the premine system, indicating the reestablished aquifer may, in part, conduct ground water very slowly. Postmine ground-water chemical quality in spoil materials had poorer quality compared to premine ground water.

Jan 1, 1981

By P J. Hawke, M F. Flis

The Hamersley Basin of Western Australia holds significant tonnages of detrital iron deposits. Formed by a cyclic weathering and eroding sequence of nominally barren banded iron formation, they may form rich proximal accumulations of iron cemented gravels distal from any obvious hard-rock iron mineralisation. While generally small, they nonetheless represent excellent economic targets as they are near surface and easy to mine. The relatively high density of iron detritals, when compared with their sedimentary hosts, makes the gravity method the primary method of exploring for these blind deposits. Identification of possible trap sites is used as a precursor to gravity surveying, with magnetics used as an ancillary method prior to drilling. Application of the gravity method in this terrain is not straightforward. Detrital trap sites are best developed next to the spectacular cliffs that form the range fronts to the Hamersley Ranges. Precise terrain corrections and use of first vertical derivatives are routinely applied to gravity data in an effort to map every possible gravity high that may reflect the presence of a detrital accumulation. Extensions to Hamersley Iron Pty LimitedÆs BS2D deposit were discovered by the routine application of gravity. This methodology has been used to create a model by which exploration for detrital deposits continue to the present day.

Jan 1, 2002

By Lawson F

Synthetic calaverite (Au Tez) has been prepared and its physical properties checked.Simple flotation tests indicate that the recovery of calaverite should be possible using n-butyl or sec-butyl xanthate collectors under approximately pi I neutral conditions with a copper sulphate activator.Roasting calaverite in air at moderate temperatures resulted in its decomposition with the formation of elemental gold and tellurium dioxide.In alkaline oxygenated cyanide solutions, both gold and tellurium tend to dissolve. At pHs less than 14, about 50 per cent of the tellurium remains as elemental tellurium; however in very strongly alkaline solutions, essentially all of the tellurium is converted to the soluble tellurite ion (TeOl-).However, even at high pHs, the solubility of gold in the cyanide solution is still low due almost certainly to passivation effects.

Jan 1, 1991

By T. Lindstad, V. Myrvågnes

In the production of high silicon alloys, carbonaceous materials like coal, coke, charcoal and woodchips are utilized as reducing agents. Primarily based on historical prices of charcoal compared to fossil reduction materials, the Norwegian Ferroalloy Industry has mostly been using coal and coke (char) as carbon source. The most important role of the carbonaceous material is to react with the SiO gas to produce SiC. The ability of the reduction materials to bind SiO gas can be measured and the value is recognised as the reactivity of the carbon source. This reactivity is one of the most important parameters in the smelting process in order to obtain a high yield of metal. The reactivity of the carbon materials is directly correlated to the material properties. It is known that the rank of the coal influences the SiO reactivity where low rank is beneficial. Coals of the same rank have however proven to have varying reactivity. In order to investigate how the micro-constituents of coal influence the reactivity towards SiO gas, three single seam unwashed coals of different origin which fulfil the requirements of the Norwegian Ferroalloy producers have been chosen. As the structure in the carbonized product is a function of petrographic constitution and carbonization parameters, the coals have been separated into different density fractions. The various density fractions of the same coals proved to have significantly different petrographic composition. The coals were carbonized according to a procedure simulating the conditions the coals experience when charged to an industrial furnace. Chemical-, physical- and petrographical properties of both the coals and the resultant chars have been thoroughly examined and correlated towards the SiO reactivity.

Jan 1, 2007

"In the mines producing over 500 tons per day, skips have replaced the old method of hoisting ore by cars run onto cages. In the car and cage method, two men (station tenders) trammed the loaded cars onto the one-deck cage, and as the production increased the one-deck cage was increased to two decks and later to four decks. Landing chairs at the underground stations were necessary in this method and were the cause of many serious accidents by being carelessly left in the shaft by the station-tenders when leaving one station for anotherabove. The labor and time occupied in loading the leaving cages were con¬siderable, and, at times of rapid hoisting, four men were necessary in taking off empty and caging loaded cars. This also required at the surface landing, as many as ten men on a shift to remove the loaded cars and replacing them with empties, and tram the loaded ones to the surface ore bins, where the railway cars were loaded.The skips used in Butte are generally of 100 cubic feet capacity and hold five tons of ore, and weigh 7,500 lbs. The cage above, to which the skip is attached, weighs 2,300 lbs. The skips dump automatically into a pocket of 50 tons capacity. Two men are with the skips underground and load them from 125 ton capacity ore-pockets, under each station, the bottoms of the pockets having an inclination of 50 degrees from the horizontal. At the bottom of these pockets a gate is operated by compressed air. The labor of loading the skips amounts only to the opening and closing of a valve in the air-line, the ore running by gravity into the skips.Besides the saving in labor, the use of the skips has removed the necessity of underground landing chairs in the shaft and the accidents which are inevitable where such chairs are used."

Jan 1, 1913

By Wygralk A, Hallenstein CP

On a world scale, many Mid-Proterozoic fluvial sediments are prospective for low grade, large-tonnage gold deposits. A significant area of the Northern Territory is covered by such Mid-Proterozoic sediments, the gold potential of which has been barely tested. The geological knowledge of these sediments is summarised. The Westmoreland Conglomerate, the basal Mid-Proterozoic formation of the McArthur Basin, has been subjected to detailed sedimentological studies in order to determine the paleoenvironments and to assess the possibility of paleoplacer occurrences. The results indicate that the sandstones and conglomerates of the formation were deposited by braided rivers and debris flows as an alluvial fan which originated in source areas to the north east. The formation contains several upward-fining cycles of sedimentation, which are related to repeated periods of uplift in the source areas. The formation of placer-type gold occurrences is possible in such depositional environments. Very limited heavy mineral sampling has indicated a cassiterite- wolframite-gold suite in the sediments of the Westmoreland Conglomerate. Disconformities at the base of sedimentation cycles are deemed to be the most likely sites for large-tonnage paleoplacer concentrations.

Jan 1, 1984

By Ronald D. Hill

Acid mine drainage is the result of the oxidation of pyrite and similar iron sulfide material and the release of iron and sulfuric acid into the environment. In addition to the acid water flowing from underground and surface mines, spoil materials in surface mines are acidic and will not support good vegetative growth; thus erosion is a major problem. Lime and limestone are the major neutralizing agents used to treat these acidic conditions. Lime is the reagent preferred by industry for treating acid discharges, although a few companies use limestone. Agricultural lime- stone is used to "sweeten" acid spoils.

Jan 1, 1974

By M. Keevy, K. Hackney

Centrifugal slurry pump station and deposition sites are a common feature of many mines and mineral processing plants. Yanacocha Mine has completed the design of a pump station consisting of two trains of four pumps each. A number of trade-off studies was conducted to optimize the pump station design. The most significant of these was determining the drive types for the slurry pumps. The pump station duty can vary considerably due to the number of deposition points round the disposal site. The standard solution to this problem on a multi-stage pump train is to install one pump with a variable speed drive to control the pump station output by varying the speed of this pump and stopping and starting other stages. However, there are a number of negative impacts associated with this approach. These include head losses through pumps that are stationary or ?wind-milling?, different wear life on pumps that are running and pumps that are stationary, and slower response to the control system with the possibility of hunting. The use of variable speed drives on all the pumps was considered as an alternative to the standard solution. The factors considered in comparing these options were the control and operational differences, the pump efficiencies and absorbed power, the expected pump wear life, the impact on pump maintenance and the cost of the drive options. For this project the option of using all variable speed drives was selected. The paper presents the following aspects of the study: ?Description of the various options investigated. This includes a discussion on the required duty and the drive options. ?Technical comparison between the options. ?Description of the factors influencing pump performance and life.

Jan 1, 2007

By Peter White

Mine Planning Shaft Collar Shaft Sinking Raises Ramp Underground Water Storage

May 1, 2009

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal&apos;s investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid&apos;s principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner&apos;s equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

By A. Haldar

This study focuses on the flow characteristics of hypereutectic Al-Si alloys in thin sections. The pattern assembly consisted of spiral horizontal patterns, 6.25 mm (0.25 inch) and 12.50 mm (0.50 inch) in thickness with a common sprue. Al-Si alloys with silicon levels of 14%, 18% and 22% were poured with superheats of 60°C, 115°C and 170°C. It was observed that metal fluidity (in terms of flow length and metal velocity) increased with increase in silicon levels and superheat for both section thicknesses. It was also observed that, for a section thickness of 6.25 mm (0.25 inch), silicon level had more pronounced effect on the metal fluidity. For 12.50 mm (0.50 inch) thickness, both silicon level and superheat affected the metal fluidity. The surface hardness of the castings increased with an increase in silicon level of the alloys at the gate and the flow tip. Detailed study of the flow tip was also carried out with a view to understanding the effect of silicon level and superheat on undulated flow length, surface hardness and microstructure.

Jan 1, 2007