Search Documents

Presiding: Herman Van Houten, Senior Marketing Counselor, Joy Mfg. Company, Pittsburgh, Pa., and John A. Reeves, Vice President, Mid-Continent Coal &Coke Co., Carbondale, Colorado. The Keynote Speaker, Senator Jennings Randolph from West Virginia, was unable to come due to pressing business in Washington. A film presentation on Surface Mining and Reclamation, "Energy Bridge," Courtesy of Pittsburgh & Midway Coal Mining Company, Denver, Colorado, was shown and was prefaced by comments from James V. Fisher. "Advantages of Longwall Mining in Western Coal Production" was a paper presented by David W. Wisecarver, Supervisory Mining Engineer, U.S. Bureau of Mines, Denver, Colorado. Mr. Wisecarver graduated from Virginia Polytechnic Institute in 1949. After two years with International Harvester and two years in the U.S. Army, he joined the engineering staff on a Bureau of Mines underground mining operation in Virginia for eight years where he saw duties as mine surveyor, shift boss, and assistant maintenance superintendent.

Jan 1, 1977

By THEODORE DWIGHT

Members of the Institute have already received a special pamphlet descriptive of the United Engineering Society building, and wilt doubtless be interested in the progress that has been made up to date-February 24th-in erecting this home for the engineering profession. The old buildings on lots Nos. 25 to 33 W. 39th St., New York, were,' removed many months ago, but final contracts for the new, building were not let until the summer of 1905. The size of the building is 115 ft. on 39th Street, and 88 ft. in, depth; the height from, the sidewalk to the top of the parapet is 220 feet. The cubic contents of the building from the. bottom of the basement floor, to the top of the roof, including the pent houses, is 2,290,000 cubic feet. The number of light's, in the building will be between 4,000 and 4,500. The air supply for Auditorium and Lecture. Halls will amount to nearly 10.0,000 cu. ft, per minute, and the exhaust. to 90,000 cu. ft. per minute. In excavating for cellar and foundations, the average depth where good rock was. found was 37 ft.-it varied, however,: from 27 to 65 ft., due to an old water-course having run through the center of the lot; this condition, and the presence of soft rock, which rapidly disintegrated when exposed to air and water, made the foundation-work very difficult. As two of the column-footings of the building have to sustain a weight of 3,000,000 11) each, the most substantial foundations are necessary; 13,000 cu. yd. of earth were excavated for the foundation and basement; and 1,600 cu. yd. of concrete were necessary, to build up the footings. In the completed building there will be about 3,500,000 bricks. Owing to the number of auditoriums, and their location, and the placing of the library on the top floor; where allowance will have to be made for the enormous weight of 300,000 books, the structural steel work has been unusually complicated in this building. For instance, over the auditorium there are two 60-ton plate-girders, made up

Mar 1, 1906

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide)are situated in Arkansas. Less concentrated brines(about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in those two states. Its value was $191 million. In 2004, the estimated U.S. bromine production was 222 kt (244,000 st). That compared with 216 kt (238,000st) produced in 2003.

Jan 1, 2005

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. Pat Doyle was born in 1849. At the age of fifteen he entered the Civil Engineering College of Madras, India, and left it at seventeen, having achieved special distinction in mathematics, chemistry,. and geology. Before be was eighteen years old he was in charge of two of the most important Sub-Divisions in the Madras Presidency, where he had ample opportunities for acquiring a preliminary knowledge of his profession, which was his chief object in joining the Public Works Department. In 1867, his energetic measures saved the island of Seringham from disastrous inundation. At this period he began contributing to the press ; and after a varied practical experience he came into public notice again in 1876, with an article in the Colliery Guardian on Indian Mines and Mining. In 1877 he became a Fellow of the Statistical Society of London. He was a founder of the Straits Branch of the Royal Asiatic Society and a life member of the parent Society of Great- Britain and- Ireland, as well as a member of the Independent Asiatic Society of Bengal. In 1878-9 he was Chief Superintendent of the Public Works of Perak; was active in having the Associate Member Class added to the Institution of Civil Engineers; and became a member of the Society of Engineers of London and of the North of England Institute of Mining and Mechanical Engineers. In 1880 he went to the Southern Colonies and held several appointments in Australia, where he became a member of the Johnsonian Club, Brisbane, and the Queensland Philo-

Jan 5, 1908

By Larry Southwick

This Peirce-Smith Converting Centennial symposium is celebrating the contributions of two men, William Peirce and E.A.C. Smith, in advancing technology allowing the copper industry to realize its full potential. However, theirs is representative of a larger story: New, simpler technology releasing the stranglehold of older, more complicated technology, new developments in vessel configuration and design finding alternate routes around dead ends in operability, advances in technique and concepts removing roadblocks of cycle time and capacity, and overall innovation opening up vast new reserves around the world to those companies willing to embrace those improvements. Our story is also one of personalities, stubborn smeltermen versus the innovators, those inside the industry versus those from outside. It is a story of an initial borrowing from the steel industry, but also Peirce and Smith, from the refining end of the copper business, taking the ideas of Baggaley from Pittsburgh’s steel and airbrake industry, who built on what Hollway, Manhès and David, Douglas, and others had done in smelter tests, further to compete with the previous primacy and closely held expertise of the copper smeltermen in Wales. These advances have been well recorded in photographs taken over the last 150 years. A number were submitted especially for this symposium. Many others were published in the mining and metallurgy press of the times. Several mining schools also retained copies of photos either taken during field trips, or donated to the school by alumni and operating companies. This presentation will provide a selection and discussion from these sources of “converters in action”, describing the various designs, operations and developments depicted. The focus here will be on the first roughly 60 years of copper converter development, from Bessemer’s days at the dawn of this new idea, up to and slightly past the time of initial adoption of Peirce and Smith’s designs.

Jan 1, 2009

By Ronald J. McGregor, Anton R. Hendriksz

INTRODUCTION The NIMCIX contactor was developed in the late sixties at the National Institute for Metallurgy in South Africa, for the main purpose of extracting uraniuy from relatively low-grade uranium solutions. ' The concept was sufficiently developed by 1974 to permit the operation of a 1500 litre per minute column to treat unclarified urgnium-bearing solution under industrial conditions. The plant operated so successfully that several large-scale units have subsequent18 teen constructed and are operating efficiently. ' Total resin consumption figures as210w as 3 per cent per annum have been reported, and the extraction efficiencies of the installations have been exceptionally good. All the solutions treated have been acidic in nature and in every case have been of such a nature as to significantly depress the maximum uranium loading on the resin beads. The chemical constituents of the leach solution fed to the loading column determines the ease with which the soluble uranium can be absorbed by an ion exchange resin. The concentration of competing ions and various resin foulants define the nature of the continuous ion exchange equipment required for efficient extraction performance. The basic NIMCIX concept is retained in these various alternate designs, but batch or continuous elution methods with fully automated or manual control systems may be selected for the different process solution conditions. BRIEF DESCRIPTION OF THE NIMCIX CONTACTOR The NIMCIX ion exchange column is a multi-stage fluidized bed contactor which is designed to permit a counter-current flow of solution and resin in order to maximize extraction efficiency. The flow o resin is periodic, based on the Cloete and Streat 5 principle of reverse flow. The basic operating cycle can be divided into five periods, as illustrated in Figure 1. For the purposes of describing the cycle, the loading column is considered; how- ever, a similar sequence may be applied to the operation of a NIMCIX continuous elution column. S'I'EP 1: During the forward flow period, Solution flows up through the column and fluidizes the resin contained in each stage. The uranium depleted solution overflows the upper flared-section of the column as the tail solution. Step 2: The flow of solution to the column is temporarily stopped and the resin is allowed to Settle onto the plates in the column. STEP 3: During the reverse flow period, a fixed volume of solution is drained from the column to the transfer vessel. This flow causes resin transfer to occur from stage to stage and also out of the bottom stage. At the end of this period, which expires when the low level switch (LS) is actuated, some of the resin is left in the conical section of the column and the pipe interconnecting the column and the vessel. STEP 4: The cone flush period ensures that all the resin left in the cone of the column and the pipe is transferred to the transfer vessel before forward flow commences. STEP 5: The loaded resin in the transfer vessel, which has been isolated from the column, can either be hydraulically transferred to the top of the elution column or eluted in the vessel before being transferred to the top of the loading column. The major advantages associated with the NIMCIX concept are: (i) Simple method of operation (ii) Contactor can readily be scaled up to large diameters. (iii) Because the resin does not pass through pumps or airlifts, and valves cannot be closed on resin beads at any time, the resin losses are exceptionally low. (iv) Operating costs are low. (v) Relatively few valves in the system. (vi) Stable operation is achieved over a wide range of feed rates and concentrations.

Jan 1, 1980

By Robert B. Hopler

To understand any technology it is necessary that a thorough background of how we got to the present stage is necessary. To do that with the subject of initiation devices we need to begin many hundreds of years ago.

Jan 1, 1990

By W. A. Plachner, Schiller E. A., S. P. Santiago

"The Monkman Coal Property is located in the Northeast Coal Block of British Columbia. It is divided into the Duke Mountain Block on the north east and the Dip Slope on the west. Together, these areas cover 39,503 ha of coal licences.The property is underlain by Jurassic and Lower Cretaceous marine and continental sedimentary rocks. Economic coal measures are contained within the Gates Formation. Exploration of the property began in the early I970s, with drilling commencing in 1975. To date, 255 holes have been drilled and nine adits have been driven to recover unoxidized coal samples.The property has a geological resource potential of 2.8 billion tonnes of medium and high-volatile bituminous coal. Medium-volatile bituminous reserves, totalling 68.9 million ROM tonnes at an over-all strip ratio of 6.3:1, have been identified in three pit areas in the Duke Mountain Block.Construction start-up will commence when sales contracts are arranged. The clean coal will be exported via the Ridley Island Terminal at Prince Rupert.IntroductionThe Monkman Coal Property is located in the Northeast Coal Block of British Columbia in the southern port ion of the Peace River Coalfield. The coal field encompasses a strike length of 250 km of Lower Cretaceous coal-bearing strata in which 13 companies have identified several billion tonnes of resources and several hundred million tonnes of reserves. Currently, two companies with contracts are in the construction phase, and are scheduled to produce coal by early 1984. Quintette Coal Ltd. has a contract with Japanese steel mills to supply annually 5.0 million tonnes of metallurgical and 1.5 million tonnes of thermal coal. Teck Corporation (Bullmoose property) has a contract to supply 1.7 million tonnes of metallurgical coal annually."

Jan 1, 1983

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By W. A. D. Edwards

"The Edmonton region accounted for 40% of Alberta's sand and gravel production in 1981 (about 12 million m3). Most of this production was by commercial operations (75%) for use in essential public works projects (64% in road and asphalt production).Although the Alberta Geological Survey delineated 1157 million m3 of gravel, a number of areas are considered to be in short supply. An econometric model was used for forecast demand in the region. Predictions, based on this forecast and estimated supply, are that 15% of the region's gravel and 3% of the sand will be consumed by the year 2010.The City of Edmonton is the largest consumer of aggregate in the region. Approximately 40% of the gravel in Edmonton's current supply area (about 55 km radius) will be used by 2010. These estimates are considered optimistic because the supply figures do not account for sterilization of deposits - some has already taken place in the region. If 25% to 50% of Edmonton's current supplies (one major deposit) were sterilized it would result in $1,000 million of additional cost due to increased haulage alone.Information on the value of aggregate resources, the location of sand and gravel deposit s and forecast demand has been made available to all municipalities in the region to aid planners and regulators in effective future use of this important resource.INTRODUCTIONAlberta is the second largest producer of sand and gravel in Canada at ab out 50 million tonnes annually. Value of provincial production exceeded $120 million in 1985. In Albert a, aggregate is used primarily in road and building construction (about 50% and 15%, respectively) and is important in such activities as petroleum exploration, oil sands development and the forestry industry.The Edmonton region (Fig. I) accounts for about 40% of provincial production and has a per capita consumption rate of about 13.4 m3 of sand and gravel per annum. Although Edmonton dominates, with approximately 50% of regional production going into the city, aggregate is produced in every county and municipal district in the region.Sand and gravel is essential to the current way of life in the Edmonton region. The resource is valuable and dwindling. The Alberta Geological Survey (a department of the Alberta Research Council) has collected information on aggregate in this region for the last decade which ca n aid government planners and regulators in pre venting sterilization and misallocation of this critical resource. This paper is a summary of that information."

Jan 1, 1989

By Andy J. Robinson, Mark D. Claassen

Railroad companies and transit authorities have been slow to acknowledge that for many—utility crossings, a direct pipe installation below live rail can be just as effective as a more intrusive traditional cased crossing. Properly designed and specified pipe jacking work, and specifically pressure-balanced microtunneling, coupled with careful specification and analysis of geotechnical monitoring and, where necessary, ground improvement measures, can produce a low-risk, low ground movement solution to the needs of utility companies and municipalities whose services need to pass below urban and rural rail corridors. This paper discusses the design, geotechnical and ground improvement aspects of microtunnel crossings below active heavy and light rail lines and crossings beneath active subway tunnels.

Jan 1, 2003

By Aiyuan Ma, Kun Yang, Weiheng Chen, Jinhui Peng, Shiwei Li, Feng Xie, Libo Zhang

In this thesis, a new process of recovering zinc sulfide ores was developed. The novel synthetic coordination leaching process mainly included two steps: microwave assisted phase reconstruction and compound coordination leaching. By applying various techniques, such as chemical composition analysis, X-ray diffractometry (XRD) and Raman spectroscopy, it could be concluded that sulfide phases would directly oxidized to zinc oxides under the 500 ºC microwave roasting and adding 30% Na2O2. What’s more, zinc leaching rate reached to 61.16% within 2 hours. Compared to the current technologies, this procedure had the advantage of avoiding SO2 emission, high leaching efficiency, simple process, manipulate easily, and low cost, which could be expected tremendous application potentials.

Jan 1, 2016

By W. Petruk, D. R. Morris

"The lead concentrate produced from the volcanogenic base metal ore of Brunswick Mining and Smelting in New Brunswick contains major to trace amounts of iron, zinc, cadmium, arsenic, antimony, copper, silver, selenium, tellurium, bismuth, sulphur, tin, indium, mercury and manganese as impurities. When the concentrate is sintered some of these impurities enter a variety of oxide phases, whereas others precipitate as metals. In the lead blast furnace the oxide phases decompose and the impurities recombine 10 form new phases, most are eventually discharged to the slag. The metals of the sinter remain as metals in the lead blast furnace where even more are produced, and are discharged largely with the lead bullion,IntroductionMany lead concentrates are produced from volcanogenic base metal ores . Such ores contain a wide variety of trace minerals and trace elements , therefore, concentrate s obtained from them will contain the trace elements as impurities . The impurities in the lead concentrate from one such ore, the Brunswick No. 12 deposit of Brunswick Mining and Smelting Corporation (BM S) in the Bathurst area in New Brunswick , were studied as pan of a larger investigation that was conducted to determine the extent of chemical reactions of the sinter within the lead blast furnace(1,2) The lead concentrate was investigated to identify the host mineral s for the impurities, the lead sinter was studied to identify the host phases, and frozen products from different depths within the BMS blast furnace at Belledune, New Brunswick were studied to determine the behaviour of the impurities.T he investigation was performed by pre pa ring polished sections o f the samples and studying them with a reflecting microscope, a scanning electron microscope (SE M) equipped with a Kevex energy dispersive X-ra y analysis system, a microprobe, and a Quantimet 720 image analyzer. The samples were also analyzed by X-ray diffractometer, and individual grains were analyzed by the Debye-Scherrer X-ray powder film method."

Jan 1, 1985

By W. C. Leslie, R. M. Fisher, K. G. Carroll

A nitride, believed to be Si3N, has been separated from three nitrided silicon steels. Germanium nitride, Ge3N4, has been prepared from pure germanium. Comparison of the diffraction patterns indicates that the two nitrides are isomorphous; on orthorhombic structure is suggested in place of the rhombohedral structure previously reported for Ge3N4. THE possibility that a nitride of silicon may, under appropriate conditions, precipitate in silicon steels or in steels killed with silicon makes it desirable to have some positive means of identifying such a compound. One such means is the X-ray or electron diffraction pattern of the nitride. A review of the meager data in the literature indicates that the nitride most likely to form is Si3N4, a conclusion supported by the results of a study of nitrided silicon steels to be published shortly by L. S. Darken and R. P. Smith, of this Laboratory. Unfortunately, there is available no diffraction pattern for this nitride. Data have been reported, however, for Ge3N4 which, judging from the similarity between germanium and silicon, might be expected to be isomorphous with Si3N4. An effort was made, therefore, to form such a silicon nitride, to determine its composition and diffraction pattern and, if possible, its structure. To this end a series of three silicon steels was nitrided under controlled conditions with the resultant formation of nitride particles which yielded an electron diffraction pattern in situ. The particles were then extracted from the steel and an attempt was made to determine their chemical composition. X-ray and electron diffraction patterns were also obtained from the extracted particles, which indicate that the nitride is isomorphous with Ge3N4, although a complete determination of the structure has not been possible. These results show that a silicon nitride with a well-defined diffraction pattern can form in silicon steels, and they suggest that this nitride is Si3N4. Materials and Procedures The sillicon steels investigated were In the form of thin sheet or strip and had the composition shown in Table I. The 0.58 and 1.21 pct Si steels were nitrided by holding them at 1110°F in an H2-NH3 atmosphere containing 3 pct ammonia for 48 hr. The nitride particle size was increased by subsequent heating at 1500°F for 13 1/2 hr in helium. The resulting microstructure is shown in Fig. 1. The steel containing 3.20 pct Si was nitrided at 1200°F for 16 1/2 hr after which it was held in helium at 1500°F for 4 hr. Its structure as seen under the electron microscope is illustrated by Fig. 2. As would be expected from the higher silicon content and the shorter holding time at 1500 °F, the nitride particles are smaller and more numerous than those in the 1.21 pct Si steel. The ammonia-hydrogen treatment reduced the carbon content of the steels to a very low level, so no interference was encountered from carbon or carbides. In the case of the 3.2 pct Si steel, the carbon was reduced to 0.003 pct before nitriding by heating in dry hydrogen. Attempts to obtain an X-ray diffraction pattern from polished and etched surfaces of the 1.21 and the 3.20 pct Si steels were unsuccessful. However, an electron diffraction pattern was obtained from the surface of the steels. The interplanar spacings obtained from these patterns arc shown in Table 11, col. 5. The nitride particles were then extracted from all three steels by dissolving the ferrite matrix in bromine-methyl acetate, the solution used in the Beeghly method for the extraction of aluminum nitride from steel. X-ray diffraction patterns of these residues, obtained by means of a spectrometer and by a 57 mm Debye-Scherrer powder camera using filtered cobalt or chromium radiation, are given in Table II along with the pattern obtained by

Jan 1, 1953

By R. K. Matheson

THE Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 19o tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65° From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. CHOICE OF RAISE A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. TIME SCHEDULE As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1942

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By B. E. Cornish

Most technical and statistical data published on pyrophyllite relating to production figures, uses, markets and sales, have in the past traditionally linked the mineral with talc and soapstone. This is due to several common superficial physical properties resulting in substitute uses and applications. However, these minerals are not similar in chemical composition and do not generally occur in a similar geological environment. Pyrophyllite now stands on its own in the marketplace-particularly in ceramic applications-due to the combination of excellent heat shock and creep resistance properties of the mineral. The increase in pyrophyllite use in the field of ceramics indicates the continuing realization of these marked unique properties. Several new fields of ceramic applications, previously the preserve of high-alumina materials, have been developed on the intrinsic properties of pyrophyllite. Pyrophyllite is an aluminum silicate with the molecular formula of AI2O34SiO2H2O. It would be more appropriate to group pyrophyllite with such materials as kyanite, diaspore, andalusite, and certain high-alumina clays in relation to its general applications (Stuckey, 1928). These materials all have good beat shock resistance properties at high temperatures and are widely used for the manufacture of refractories. For those reasons they are interchangeable in some applications. Pyrophyllite also has many uses in nonceramic applications, the most important to date being as a substitute for talc in fillers. The major pyrophyllite mining operations are located in the US, Japan, Korea, Canada, and Australia, where the mineral is widely used as a raw material for general ceramic, mineral filler, and dilutant applications. Commercial Applications Pyrophyllite was first used in the last century for lining stoves and fireplaces, and also in the carving and polishing of ornamental objects. The rise in industrial demand for new products and applications resulted in the introduction of pyrophyllite as an alternative, mainly for talc and soapstone. Industrial filler applications followed for paint, paper, cosmetics, rubber, pesticides, crayons and pencils, and bleaching soap. The first use of pyrophyllite in ceramic applications was prior to World War II, in the manufacture of ceramic cladding tiles in the US. This was followed by the production of kiln furniture refractories and whiteware when pyrophyllite was offered by suppliers in North Carolina as an alternative to some local clays. The largest tonnages of pyrophyllite used today are in refractory linings in steel ladles in Japan, as seen in Table 1. The consumption of pyrophyllite in Japan is second only to clay and chamotte among refractory raw materials used. Recently this technology has been adopted in Australia. Japanese and Australian practice has resulted in appreciable technical and economic benefits, particularly when pyrophyllite is used in combination with zircon. The potential growth for this application is substantial if US and European steelmakers follow. Investigation and research into the properties of pyrophyllite determined the following main advantages of pyrophyllite-based ceramics: high corrosion resistance for molten iron, steel, and slags; good heat shock resistance; good indices of deformation under load and hot creep resistance (refractories); and increase in mechanical strength of whiteware products promoted by a better distribution of mullite in finished products (also obtained at lower firing temperatures than normally required in production of triaxial ceramics). White cement

Jan 1, 1983

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988