Search Documents

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

By I. S. Thompson

A program of geochemical till prospecting, carried out by Derry, Michener & Booth in 1974, was instrumental in t~ e discovery of a copper deposit in Currie Township, Ontario, beneath thick lacustrine deposits of the Abitibi Clay Belt. The prospecting system involved the continuous collection of glacial sands and gravels beneath the clays, using a track-mounted, dual-tube rotary drill, and the separation and geochemical analysis of the heavy mineral content for Cu, Zn, Pb, Ag and Au. In one of 22 holes drilled down-ice from nine Canadian Nickel airborne EM conductors, fragments of chalcopyrite-bearing graphitic argillite, assaying 12% Cu, were recovered from a 14-foot gravel section beneath 83 feet of clay. Ultimately, mineralization was identified in 10 of 11 additional holes drilled up to 3,000 feet down-ice from the Currie deposit. The glacial fan, when compared to the 1,200- by 165-ft area of the subcropping mineralization, is at least 20 times the area of the deposit and is the result of glacio-fluvial reworking of the mineralized ground moraine. The Currie deposit is contained within a Keewatin succession of graphitic argillite, dacite tuff and graywacke, which is intruded by dacite and feldspar porphyry sills and dykes and truncated by a Keweenawan diabase dyke. Grade and thickness of the mineralization, which lies chiefly within the argillite, is related to felsic intrusives and hydrothermal alteration, and to fold hinges.

Jan 1, 1979

By Mirian Mamani

El presente texto señala el magmatismo de los Andes peruanos y la influencia de la madurez cortical de los depósitos minerales y su posterior delineación de las fuentes de mineralización.

Nov 1, 2013

Australis Mining N.L. operates a continuous mode carbon-in-pulp (CIP) gold plant, processing sand and slime tailings from previous gold mining operations in the Norseman area. Plant design is that of conventional countercurrent contact between pregnant pulp and activated carbon. Gold desorption is achieved by the Zadra process using near boiling tempera- tures and atmospheric pressure. Process water is drawn from nearby Lake Cowan (saline). The plant operates at, or above, design specification of 400 dry tonnes per day. This paper describes the plant design and operating processes utilised in optimising throughput and gold recovery. TNTDnPTTnmTnM Favourable world gold prices and substantial reserves of sand and slime tailings prompted Australis Mining N.L. to construct a gold extraction plant during 1981. The projected plant throughput was set so as to complete treatment of available tailings over a three year period. Metal- lurgical tests indicated that, with a regrind facility satisfactory gold recovery could be achieved using a countercurrent CIP process. Reflecting the entry of Australis Mining N.L. into its first large scale treatment operation, the plant design emphasised simplicity but effectiveness of Operation.

Jan 1, 1982

This work examined the feasibility of in-mine coal preparation in two phases. Phase I included a survey of previous investigations and a preliminary analysis of the economic and technical feasibility on a selection of representative sites and degrees of cleaning. The contract was terminated at the end of Phase I. The preliminary analysis determined that in-mine preparation systems can be applied using currently available technology. The most likely mines for application will have shaft or slope access and be deeper than 500 feet. The refuse disposal systems technically feasible are (1) pneumatic placement of coarse refuse in room and pillar panels or longwall faces, (2) mechanical placement of coarse and fine fractions in room and pillar panels, and (3) hydraulic placement of fine fractions in room and pillar panels. The economic feasibility is much more dependent on the refuse disposal-system than on the preparation system. It is estimated that the capital cost of an in-mine preparation and disposal system would be $6.00 per clean ton and the operating cost would be $1.24 per clean ton for a 1 million clean ton per year mine.

Jan 1, 1982

By Paul S. Korinko, Simona E. Hunyadi Murph

To address a radiological contamination event, a materials and process project was initiated. During the course of this project, processes and materials were developed that successfully captured zinc vapors physically and chemically, respectively. However, the physical traps were placed in an undesirable area and it was determined that the chemically captured zinc reactions was reversible. Consequently, advanced nanomaterials are being developed to capture zinc vapors. The current state of the art of the science and engineering of these materials and their efficacy for zinc capture and retention is discussed in this paper.

Jan 1, 2015

By Mirian Mamani

Luego de revisar la data ofrecida por estudios de magmatismo y geoquímica para varios yacimientos epitermales relacionados con grandes complejos volcánicos en el sur y norte de Perú, además de analizar dos grandes complejos volcánicos con varios depósitos epitermales; el presente estudio destaca la importancia de estimar el volumen emitido y los tipos de erupciones de los aparatos volcánicos en tiempo y espacio, así como de conocer la geoquímica y arquitectura de todas las rocas emitidas y de caja. Los resultados de este estudio pueden orientar la toma de decisiones y la exploración por Au-Ag en vetas y diseminados en la región andina.

Feb 28, 2020

By Peter Dowden, Trevor Carter, Allan Moss, Bruce Downing, Richard Beddoes

Traditionally (with a few exceptions) tunnel boring machines (TBMs) have been utilized on tunnel projects where the risks associated with deep tunnels (rock burst, squeeze, etc) are low (or expected to be low). This has generally been due to the extremely adverse consequences of entrapping or damaging a TBM under such conditions; but also due to the relative difficulty of dealing with these ground conditions in the confined working area of a TBM, in comparison to a drill and blast heading. This paper review the constraints of operating a TBM in a deep tunnel and discusses related project experience, particularly recent and current experience with TBMs in the deep Alpine Base Tunnels. Potential future applications of TBMs in the development of large, deep underground mines are also discussed.

Jan 1, 2007

By A. F. Matheson

"Bankfield Consolidated Mines, Limited, and Tombill Gold Mines, Limited, in the Little Long Lac area, Ontario, mined an orebody that was common to both. The discovery' of this orebody was made by surface prospecting in May, 1932, on Bankfield ground, following an original discovery made in the same manner on the same property on a small reef in Magnet lake in October, 1931. The production from the two mines between 1937 and 1942 was approximately 135,000 oz. gold from about 420,000 tons of ore, an average grade of 0.32 oz. a ton. Production was nearly equally divided between the two properties. Both mines are now closed, the ore exhausted.""The ore is mainly sheared and fractured greywacke and porphyry impregnated by silica and small amounts of metallic minerals. To a lesser extent there are definite quartz veins in the ore zone""(l). The metallic minerals present were principally pyrite, arsenopyrite, pyrrhotite, and native gold .As at other mines in the Little Long Lac area, an elongated, broad, deep trough of folded, steeply dipping volcanic and sedimentary rocks, striking roughly east-west and surrounded by younger granite, is host to the orebodies of the Bankfield and Tombill. In the immediate area of the two mines iron formation and conglomerate bands occur nearby both north and south of an intrusion of porphyry-Cliorite, suggesting repetition of beds and folding. Although considerable drag folding is in evidence, folding on the above scale has neither been proved nor disproved."

Jan 1, 1954

By F. Q. P. Leiding

SYNOPSIS A technique is described for measuring the change in volume in a borehole drilled in a rock mass subjected to stress and strain. It is shown that the volumetric strain or change in volume provides a practical estimate of the the stress in the rock.

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By K. U. Kainer, A. Stark, D. Tolnai, M. Hehenberger, C. L. Mendis, N. Schell, N. Hort

Samples of an as extruded Mg-6Zn-0.6Zr-0.4Ag-0.2-Ca (wt.%) alloy was compressed at room temperature and at 250°C. The in situ deformation tests were performed at the P07 (HEMS) beamline of PETRA III, DESY, with a modified DIL 805 A/D dilatometer with to Kapton windows on the sides and the induction coil opened for the beam to transmit the sample. The deformation rate was 10-3 s-1 the samples were deformed to failure. The diffraction patterns were recorded every 3 s with a Perkin Elmer 1621 Flat Panel Detector. The results reveal that different deformation mechanisms are activated during compression at a given strain value. At room temperature twinning is the dominant deformation mechanism, while at elevated temperature dynamic recrystallization occurs while the contribution of twinning to deformation is significantly reduced. The compressed samples were further investigated with conventional metallography and SEM-EBSD to determine the volume fraction, the type of twinning and the strain retained within the grains. The parallel testing of pure Mg samples under the same conditions allows comparison of the compression behaviour of the ZKQX alloy with Mg.

Jan 1, 2014

WHEN the writer resided at Zeehan, qn the West Coast of Tasmania, some years ago, he took a keen interest in the geology of the district and availed himself of the opportunity to investigate occurrences, of the varied minerals in which the field abounds. The following notes were compiled as a result of one of his periodical visits to the outlying mining districts, when an examination was made of the bindsay Reward tin mining property, which has an area of 140 acres. This is most easily reached from Renison Bell, the centre of the North Dundas tin-fields, on the Emu Bay railway, 'about' eight miles north east of Zeehan. Thence a pack track some 14 -miles long connects with the mine, crossing the Piemah River by a fine suspension bridge.The mine itself is situated on the main south leading spot of the Parson's Hood Range, at an altitude of some 1600 ft. above sea level. The Parson's Hood Range is composed of granite and is an extension of the rugged Meredith Range. A remarkable feature is the uniform topography of the surrounding country when viewed from the peaks. Except where dissected by the rivers and creeks, the surface is practically level and, indeed, affords a striking illustration of an ancient uplifted peneplain.The mine has been opened by means of trenches and adits, and the ore-body proved to extend for a length of 30 chains, with an average width of about 100 ft. Its general trend is west-north-west, and its dip, which is steep, corresponds to that of the country-rocks. These latter, which are of sedimentary origin and generally regarded as of pre-Silurian age, have been tilted at high angles, consequent, no doubt, on the crustal movements produced by the intrusion of the huge granitic masses which now form the high ranges in the vicinity.It may be here remarked that it is not Within the scope of this paper to deal with the sequence of events leading to the geological structure...

Jan 1, 1923

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

Jan 1, 1924

Jan 1, 1924

By Luis Ayala, Francisco Solano

Entre Huachón y Corralcancha (Cordillera Oriental) se ha identificado un corredor estructural NO-SE (Chaska-Rumichaca) ubicado a ~30km al este de Cerro de Pasco. Cuyos límites son fallas regionales que determinan un bloque paleozoico del Complejo Metamórfico del Marañón (CMM). El límite occidental (Falla Rumichaca) corresponde a una falla inversa de vergencia SO que aflora dentro del CMM; mientras que el límite oriental (Falla Chaska) es una zona de cizalla compresional de vergencia NE que coloca al CMM sobre los Grupos Mitu (Pérmico superior-Triásico inferior) y Pucará (Triásico superior-Jurásico inferior) replegados. Este límite exhibe un flexionamiento de NO-SE a N-S que está asociado a fallas subordinadas de cinemática compresional, extensional y de desgarre.

May 1, 2008

By Lori Kormos, Jhonny Carrión De la Cruz, Dominic Fragomeni, Elizabeth Whiteman, Jorge Oliveira

"Process diagnosis, flowsheet design and optimisation are most effectively and efficiently achieved through the use of metallurgical testwork combined with more modern quantitative mineralogical techniques. Integration of the mineralogical data in testwork programs provides a resolution that cannot be obtained from assays alone and can direct the flow of work to result in optimized conditions more quickly than would otherwise be possible. At Xstrata Process Support (XPS), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro Analyser) information can be employed to diagnose specific issues in a plant or lab scale test and are routinely combined with other metallurgical data sets to benchmark performance, design and optimise flowsheets. Representative sampling protocols for ore bodies or test products, the use of geometallurgical unit classification and high confidence metallurgical test programs are key components of the strategy. Two case studies from Xstrata Zinc’s Antamina Mine and Concentrator in Perú, and Xstrata Nickel’s Nickel Rim South Mine in Sudbury are described to show how the use of quantitative mineralogy were used to diagnose a plant issue and how the data can be integrated into metallurgical programs to assist mineral processing engineers to design and optimise flowsheets.INTRODUCTIONOver the past decade, there has been a shift away from metallurgical testing that employs only chemical assays to quantify performance; the use of empirical observation in order to optimise a flowsheet; and the extraction of bulk samples for testing or piloting. The integration of geological information into the planning and execution of testwork programs including the use of quantitative mineralogy has improved the overall quality and predictability of metallurgical programs. At the same time, improvements to metallurgical testwork protocols such as rigorous statistical assessment of results, the use of factorially designed experimental strategies (DOE), and replicate flotation with appropriate quality controls, has improved the confidence level in these results.Process diagnosis, which utilizes quantitative mineralogy, can clearly define the root cause of the metallurgical issue. Whether used on its own to diagnose an issue or in combination with other metallurgical testwork, the use of mineralogical data has become the standard in the mining industry."

Jan 1, 2010

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987