Search Documents

By R. Hammen

Processes are needed to rapidly and cost-effectively produce highly pure lithium salts for the rechargeable battery sector. Lithium purification is a chemical engineering challenge, due to the low concentration of lithium compared to sodium, potassium, magnesium, calcium, and transition metal ions commonly occurring in lithium brine resources. We describe a Solid Phase Extraction (SPE) process that rejects sodium and potassium, while binding lithium and other higher valent ions. Lithium is then harvested by selective displacement from the SPE column. The rapid equilibration kinetics of SPE composites enables these ion separations to occur in a small SPE column and in one column stage. The chemical parameters of the process are described.

By H Pray, H. W. Russell, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By H. W. Russell, H Pray, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

By S E. Box, J L. Mauk

The Middle Proterozoic metasedimentary rocks of the Belt Supergroup contain important metallic mineral deposits like the diagenetic sediment-hosted stratiform copper mineralization, including the Troy (Spar Lake) deposit and the epigenetic hydrothermal veins in the lower Belt and Ravalli Group in the Coeur d'Alene district. Magnetite (Fe3O4) is a common and widespread accessory mineral in these rocks and can have multiple origins including ore stage in deposits, mobilization stage in source rocks, metamorphism of red beds and alteration mineral in thin halos enveloping Ag-rich veins in the Coeur dÆAlene district. As shown in several classic studies, the composition of magnetite from igneous rocks varies significantly in response to controlling factors such as melt composition, temperature, silica activity, and oxygen and sulphur fugacity. Therefore, the distinctively different geologic settings within the Belt Supergroup strongly suggest that there may be differences in the magnetite compositions. However, initial microprobe analyses detected no variation in magnetite composition.   Three possibilities may give an adequate explanation for these initial results: 1.      the magnetite formed primarily as pure Fe3O4, 2.      one or more tectonothermal events led to regional scale re-equilibration that affected all rocks in the field area, and 3.      the variations in the composition are below the detection limit of the microprobe.

Jan 1, 2007

By Henry Howe

THAT the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First; each particle of any composite liquid, whether it be an aqueous solution or a molten metal; in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the, existing temperature, - and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already, solidified; A, Fig. 1. The other part is, fusible at the existing temperature and hence remains molten. In the case of carbon Open steel, the part. of each drop which actually j; Sea solidifies is poorer, in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying,. half-drop enriches . the other, half-drop in carbon, and Layer of Liquid thus. makes it unfreezable at the existing tem- Fig. 1.MECHANISM OF perature. SOLIDIFICATION. By this- mechanism there arises during solidification a " littoral" or shore layer- of liquid, B, Fig. 1, bathing the already solidified. walls, and more fusible than either those walls or the great remaining central mass of liquid or "deep sea," C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile. heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal

Jan 2, 1919

By Scott D. Thomson

The client for this project specializes in the use of state-of-the-art technology to fabricate and assemble composites and metal-bonded structures for commercial and military aircraft programs. One of the key components for this operation at the client's plant is a highly precise computer-numerical-controlled router known as the Shoda Machine. This machine tool was installed at the plant in July 1998 for the manufacture and inspection of aircraft parts, and it is extremely sensitive to deflections. To monitor the occurrence of deflections, an internal laser system continuously checks the machine calibration. Deflections in excess of 5/1000-inch in the foundation on which the machine rests require costly periodic re-leveling and recalibration of this tool. Therefore, a significant problem arose when measured deflections during machine operation were as large as 20/1000-inch. In addition, the foundation was cracked in at least three places as a result of elastic foundation movement caused by dynamic loading as well as shrinkage and loss of base support. Deciding on a remediation procedure to alleviate or eliminate these problems involved the following important considerations: (1) achieving the client's need for reducing deflections to less than 5/1000-inch, (2) minimizing the repair cost as much as possible, and (3) reducing the time required for implementation of the foundation remediation solution. After evaluating the advantages and disadvantages of several alternatives, jet grouting was selected as the most suitable solution. The jet grouting program provided columnar elements of soilcrete to remediate the Shoda Machine foundation.

Jan 1, 2003

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By M. C. Ruiz

This work outlines the results of leaching studies on a copper concentrate containing chalcocite (Cu2S) and digenite (Cu9S5) with an acid saline solution of cupric chloride oxygenated at ambient pressure. The variables studied included the stirring speed, concentration of cupric ions, concentration of HCI, concentration of chloride ions, oxygen flow rate, temperature and time. The leaching system was found to be very effective for the dissolution of the concentrate. Over 95% of the copper was dissolved in 30 minutes with negligible dissolution of iron. The dissolution of copper increased with the stirring speed up to about 400 rpm and depended little on the total chloride concentration. The oxygen flow rate affected the dissolution of copper only below 0.1 1/min. The concentration of HC1 did not influence the dissolution providing its was sufficient to avoid the precipitation of copper oxychloride. The study of the effect of the temperature showed a maximum in copper dissolution around 90 "C

Jan 1, 1997

By Jerome Alexander

IT is an outstanding fact of Nature that many of the practical properties of substances are dependent, not on their ultimate chemical composition, but on the kind and degree of aggregation of their constituent particles. Thus, a granite boulder is unmoved by wind or water, but if reduced to a fine dust it will be blown about by the wind and washed away by the rain. Carbon in one crystalline state of aggregation (diamond) is the hardest known substance, whereas in another crystalline state (graphite) it is so soft that it is used as a lubricant. Laying too much stress on the mere chemical analysis of substances is apt to obscure the fact that the nature of the aggregation of their particles is always a factor of importance, and sometimes the most important factor. Colloid chemistry deals with matter in. a very fine state of subdivision; its sphere begins with particles just a little smaller than a wave length of light-and extends clown until they blend into molecular dimensions. With particles of this size; such phenomena as surface tension and adsorption, which depend on the development of free surface, become enormously magnified. Thus a cube of 1 cm. edge has a surface of only 6 sq. cm.; but if it is reduced to colloidal dimensions by being cut up into cubes each having an edge of 0.01 , (0.00001 mm.), it will yield one million, million, million (1,000,000,000,000,000,000) such cubes, having a combined area of 600 sq. in., or 21,274 sq. ft. The tiny force with which a drop of rain clings to the window pane becomes a. factor to be reckoned with, if the surface involved is increased millions of times. From the colloid-chemical viewpoint, metals and alloys may be regarded as jellies or sponge-like structures, the viscosity or stiffness of which at ordinary temperatures is exceedingly great; and like all jellies their properties are dependent on the composition and degree of dispersion of their constituent phases. These, in turn, depend on chemical composition, mutual solubility, speed of chilling, subsequent mechanical and heat treatment, etc In fact, in preparing metals and

Jan 2, 1919

By Henry T. Mudd

FLUORSPAR is a nonmetallic mineral aggregate or mass containing a sufficient quantity of fluorite (CaF2) to be of commercial interest. It has only moderate value per unit of weight and its cost as a percentage of the cost of finished consumer products is nearly negligible. Nevertheless, it has wide and great industrial importance. In periods of national emergency it is a mineral without which many very necessary manufacturing processes would be greatly handicapped; a few could not exist. Fluorite contains 51.1 pct calcium and 48.9 pct fluorine. Industrial grades of fluorspar prepared for the consumer normally contain from 85 to 98 pct fluorite, depending on the use. The ores may contain as little as 30 pct fluorite, depending on many factors such as accessibility to transportation and markets, character of ore, and prices. Fluorite is a lustrous, glasslike mineral, generally translucent to transparent; it may be clear and colorless or range in color from slightly bluish through various shades of violet, amethyst, purple, green, and yellow. It crystallizes in the isometric system and possesses perfect octahedral cleavage. Commonly it occurs in masses of very pure crystal- line material with aggregates of cubical crystals in open spaces, but - it is also found in fine to coarse granular form. Banded veins and masses with fibrous, radiating structure occur locally. It is usually found associated more or less intimately with other minerals and rocks, from which it must be separated for commercial use. The specific gravity of fluorite is 3.18 and the hardness is 4 in the Mohs scale, compared with 7 for quartz and 3 for calcite. It is distinguished from calcite by its failure to effervesce with dilute hydrochloric acid. Heated with sulphuric acid, it gives off fumes of hydro- fluoric acid, which etch glass.22,25,33.34,35.41

Jan 1, 1949

By Christopher P. White, John R. Wagner

This paper will discuss the complex and difficult soil conditions encountered in the sinking of 15 shafts of 18m to 27m depth and the excavation and lining of 6700m of 2.74m dia. interceptor sewer on Staten Island, New York. The complex soil profile consists of dense glacial till and sand outwash strata overlying the much older cretaceous sand, silt and clay strata. The tunnel varies from 8m to 14m below the nearby sea level. A significant amount of boulders were anticipated in the till. therefore, a decision was made to excavate the tunnel with a digger shield installing bolted, gasketed concrete segments. The bid documents stated the soils were dewaterable. Several conditions occured in this complex soils matrix which required modifying the planned means and methods including the necessity to use compressed air. The conditions encountered and the equipment used will be described.

Jan 1, 1991

By H. W. Russell, Paul D. MILLER

IT is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranular corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels have been ably discussed by Bain and co-workers1-3 and by other investigators.4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a. mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measurements, measurement of the degree of cracking produced on bending over a mandrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A-10 11 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. EXPERIMENTAL METHOD A small area of the steel under test is subjected to an anodic treatment in a cell that can be clamped onto a sample or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8-in. diameter. The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By Seungyeol Lee

Currently, a new construction method using a robotic system is widely spreading in construction sites. This study is related to the design of glazing robot?s teach pendant which can improve convenience of handling and hence improve the productivity through the efficient interaction between an operator and a robot while doing glazing works, e.g., curtain wall installing. The suitability of selection and arrangement of control switches was assessed according to mechanical motions of a glazing robot, and design guidelines for improving convenience and productivity were drawn up through questionnaires carried out by site operators. To verify the proposed design guidelines, working time comparison of the proposed teach pendant and the existing teach pendant was executed.

Aug 1, 2013

By S. W. Parr, T. E. Layng

The low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700" or 800" C. For convenience in this discussion, the single number 750" will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750") there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750") there is substantially no secondary decomposition; above 750") the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750". Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for- example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing . conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement of the evolved gases is lively and reduces, correspondingly, the time for the retention of the gases in the passageways where these milder decomposing conditions exist. It is acknowledged that the maintenance of these temperature conditions at the present time has only an ideal and not a practical status. Actual operations under these conditions, as a? industrial accomplish-

Jan 1, 1920

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By M. W. Grabinsky, M. S. Diederichs, E. Hoek

Provided that they are used correctly, numerical models can be of considerable assistance to mining engineers in designing underground excavations. Guidance is given to the engineer or geologist who is not a specialist in numerical analysis but who is interested in using numerical modelling tools or in employing someone to analyse the stresses, displacements and failure in the rock surrounding underground excavations. A description of the theoretical background to a number of these numerical models and discussion of the advantages and disadvantages of each are followed by guidelines on the selection of appropriate models for each stage in the development of a mine, from exploration to the completion of mining

Jan 1, 1991

By A. M. L. Cushing, S. Kelebek, A. Ghahreman

Iron sulfides are part of many ore deposits affecting flotation separation of non-ferrous base metals from them. Open-circuit potential (OCP), potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) measurements were carried out with pyrite and pyrrhotite electrodes to investigate their reactivity under various flotation conditions, which involved the use of TETA, SMBS, and their combination. TETA was found to adsorb on the electrode surfaces causing a significant increase in charge transfer resistance of the product formed, which was most significant at OCP. This effect is much less with SMBS, indicating its greater surface reactivity compared to TETA. The combined use of these reagents decreases charge transfer resistance to a greater degree than that experienced with their individual uses. Addition of Cu2+ as a potential activator to this system nearly eliminates the action of TETA on the electrode surface, which can be attributed to sequestration/chelate formation in liquid phase. The relative effects of these reagents on pyrrhotite electrode are similar to that of pyrite. The main difference between the pyrite and pyrrhotite electrodes is that the observed charge transfer resistance on the pyrrhotite surface with each reagent case is significantly lower by 3 to 4 fold. This is compatible with its anodic nature and ease of oxidation since the OCP value of pyrrhotite is lower than that of pyrite. Results are discussed in relation to flotation/depression behavior of these iron sulfide minerals in mineral separation processes.

Jan 1, 2017

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004