Search Documents

By L. O. Howard

L. D. RICKETTS, New York, N. Y.-The advance which has been made in Smelting has been in the line of cheaper cost of handling, due to larger units and decrease in losses. At the International smelter, Mr. McGregor designed everything to handle the ore under cover. But we do find an unaccounted for loss of 0.7 per cent. of our copper, which is serious. Mr. Wallace has made a suggestion that I think metallurgists ought to know of and think about. He made it years ago-and that is that one of the chief losses is undoubtedly in the charging and discharging of the calcine cars. His idea is that possibly the dryers and heaters might be put immediately over the reverberatories So that they could discharge in conveyors. They could feed on both sides, and thereby the dust raised by discharging in the cars from the hoppers could be overcome. E. P. MATHEWSON, Anaconda, Mont.-I might Say a few words on the plants we have visited So far. I was particularly struck with the cleanliness of the plants, which is next to Godliness. I noticed also that the skull-cracker arrangement they have for handling their converter slag is very good. And they have paid considerable attention to ventilation, and are taking steps to take care of the health of the men. "Safety first" has been well looked after in all the plants we have visited so far. The steel structures are right up to date, and the buildings are of the most modern type, and everything is conveniently arranged. I think the designers of the plants in the Southwest are to be congratulated on what they have done.

Jan 12, 1916

By A. W. Kbair, L. D. Gehl

"INTRODUCTION The rock-bit interaction during the cutting process in underground mines has been a matter of great concern to mining operators, researchers and manufacturers, particularly after the passage of strict environmental laws. Coal cutting bears directly on airborne coal dust generation and rock cutting generates frictional sparks which may cause face ignitions, jeopardizing the productivity, safety and economy of the industry. It is imperative to investigate into the factors which have influence on bit we.ar. Hurt and Evans (1981) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits, and also worn bits were more responsible for ignition than the new bits. The results of a study (Khair et al., 1992) suggested that after 7% weight loss, the bit should be replaced. The polycrystalline compact diamond (PDC) tipped bits are reported to be cost effective in a study done by USBM (Twin Cities Research Center), and it was stated that the PDC tipped drill bits had 80 to 100 times longer life than the ordinary tungsten carbide (WC) tipped bits.This paper presents the results of the experiments which were conducted utilizing a coal cutting simulator at the laboratory of the Department of Mining Engineering, West Virginia University, USA. The description of the machine and the experimental set-up have been described elsewhere (Khair et al., 1989; Gehi & Khair, 1994), and therefore, will not be discussed here. The rock types which were used in experimen~ are Tennessee sandstone, Berea sandstone and Indiana limestone. The operating parameters include (1) drum speed, (2) water spray pressure and (3) bit type. Besides studying the wear characteristics influenced by the above mentioned variables, the effect of these parameters on the required cutting force, specific energy consumption, acoustic emissions rate and rise in temperature of the bit were also studied. A preliminary study was also done to compare we.ar characteristics of the WC bits with those of the poly-crystalline compact diamond tipped bits."

Dec 1, 1995

A new $18-million hydrometallurgical ore treatment facility for the recovery of molybdenum oxide was dedicated at Climax, Colo., on November 19 by Climax Molybdenum Co., division of AMAX. The Company has been producing molybdenum from molybdenite (MoS2) ores since 1918. Now oxide values, formerly lost in the sulfide flotation plant tailing are to be processed to yield about 3 million Ib per year of metal. In 1965, Climax produced about 50% of world molybdenum from sulfide ore. This ore is mined at the rate of 42,000 tpd. The annual production of concentrate is 100 million lb containing 90% to 92% MoS2, or about 50 million lb of metal. As only a relatively small portion of the total Climax production is sufficiently enriched in oxide molybdenum to process through the new plant, 5700 tpd of selected ore containing 1.5 lb of Mo per ton is now treated by the new process.

Jan 12, 1966

` LAWRENCE ADDICKS, New York, N. Y.-We have really two competitive processes for the production of electrolytic zinc. In the process used at Great Falls, the ore is roasted and the calcines leached, leaving a residue which has to be smelted; in the other method, the ore is burned, the zinc and lead fumed off, and the condensed fumes are leached. I do not think that we can yet come to any decision as to which is the better way to attack the problem. Of course if we roast first and then leach, various substances remain in the calcines which may consume sulphuric acid; whereas if we do the burning first, we obtain simply the zinc and lead oxides, with considerable sulphate, in the fume, and there is no shortage of acid. It also depends partly on the complexity of the ore. The one that Mr. Hall is treating and the ore they are treating at Great Falls are not quite alike, but I think they are sufficiently similar to make a comparison of the two methods, working in competition, on different parts of the country, very interesting. C. E. SCHWARTZ, Miami, Okla.-Mr. Hall states that the Joplin conditions are not suitable for the manufacture of electrolytic zinc. When we speak of Joplin ore in general, we consider, of course, a 60-per cent: concentrate with comparatively low iron, but if a low-grade concentrate could be made from tailings and so-called chats, then the problem would be quite different. A Joplin ore is comparatively simple to treat electrolytically, and I believe the electrolytic process would open a field for the treatment of such ores as would not be ordinarily smeltable; that is,

Jan 1, 1918

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as pyrope garnet and magnesian ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1984

By Thomas L. Richardson, David R. Chapman, Gary W. Gilbert

The two contracts of the Big Walnut Augmentation/Rickenbacker Interceptor(BWARI) sewer project for the City of Columbus, Ohio total nearly 35,000 feet of 14and 12-foot diameter tunnel. EPB TBMs will install precast concrete segmental lining through difficult glacial soils ranging from clean granular to hard till with high groundwater and boulders, crossing roads, railroads, and a large stream. Construction of 12 shafts and a large Interconnect Structure involving major ground stabilization work is required. The paper will review design of major project elements and present an update on construction progress.

Jan 1, 2005

By F. C. Pittman, D. W. Harriman, J. C. St. John

This paper mentions briefly the history of hydraulic jetting as applied to perforating and fracture initiation. It points out the advantages of hydraulic perforation and undercutting as an aid for creating a fracture at the point desired rather than depending upon the weakest point in the formation for breakdown. It describes early experimental work with jet nozzles in search of better nozzle materials. The effect of splash-back damage and its subsequent influence on jet body and tool design during this work is discussed. A series of cutting-rate curves for jets cutting steel and steel-cement-formation combinations is presented to show the effect of hydrostatic head and the point of diminishing returns with respect to cutting time. There is a series of photographs showing various types of rock formation in which perforation and undercutting tests were made. These stones were drilled and the casing cemented in place as in an actual well. The casing was perforated and circularly cut as if preparing for a fracturing job. The conclusion reached in the paper is that hydraulic jetting with sand-laden fluid can be used for perforating and undercutting casing, cement and formation rock for the intended purpose of inducing the formation to fracture at a desired point. INTRODUCTION Hydraulic jetting as a means of cleaning a formation during acidizing has been used for many years. The acid-jet gun was used to clean formation and for drilling cement from casing with acid. This tool was dropped to a seating ring installed on the tubing and could be retrieved by reverse circulation or wire line. In this process, the fluids were directed against the formation to clean and penetrate beyond the mud-damaged area. After the development of the hydraulic fracturing process, interest in jetting the formation with abrasive-laden fluid was renewed. The cutting action of abrasive fluid on pumping equipment, which is a well known problem, has been utilized to perforate and undercut casing, tubing and formation. In this process, surface areas are provided in the formation on which the frac- turing pressures may work to produce a fracture at the location desired. EQUIPMENT The tools used consist of bodies containing two, three or four jets in a single horizontal plane equally spaced around the circumference. The body is threaded to the end of a string of tubing and run into the well. In addition, an expendable tool is available that may be left in the hole after perforating and produced through until necessary to remove the tubing. The bottom of each tool is equipped with a ball-type back-pressure valve. The ball can be reversed to the surface and recovered. This allows reverse circulation so that loose sand which accumulated below the tool while jetting may be removed before the fracturing job. The present jetting tools are of such length that, when screwed together, the jets fall on 12-in. spacing. ANALYSIS OF THE PROBLEM Early work with nozzles indicated that hardened steel was not a suitable material for jets and that more durable material would be required. Ceramics were tried and found to be superior to steel but still too shortlived for most applications. Tungsten carbide, which was tried and found to be the best material available, is now being used for jet nozzles. Analysis of the problems presented by this process indicated that the following information was needed. 1. The effect of submergence on a jet stream and the effect of submergence on the cutting rate of a jet stream. 2. The cutting rate and depth of a jet stream in steel. 3. The cutting rate in various formations and point of diminishing returns. 4. Size of hole or slot cut in a pipe by a given jet. 5. Fluids and sands used. 6. The flow of various weight fluids through the jet nozzle and the discharge coefficients. 7. The type cut formed in the formation by the jet stream. 8. The stretch and contraction of tubing due to temperature and pressure. The cutting effect of a jet stream on a target in the atmosphere is rapid and spectacular as most of the

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls. Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By G. P. Holmes

"Bell Copper is situated (Latitude 55°0''N, Longitude 126°14W) on Newman Peninsula on the east side of Babine Lake at an altitude of 2,450 feet above sea level. The mine site is approximately 170 miles north west of Prince George and 40 miles east of Smithers. Access to the property is by way of 30 miles of paved road to the Village of Granisle on the west shore of Babine Lake and then a further 9 miles of unpaved road to Bell Copper's west dock. The two mile lake crossing is made using a tug and barge. A compressed air bubbler system maintains an ice free channel for the barge during the winter months.Temperatures range from summer maximums of around 32 °C to winter minimums in the region of minus 40°C. Long periods in winter may be spent with temperatures in the range of minus 15""C to minus 28°C. Freezing temperatures usually start in October and last for six months. The lake normally freezes over in mid December and the ice breaks up in mid May. Snow accounts for approximately two t11irds of the annual precipitation of twenty-one inches."

Jan 1, 1976

By R. R. Unterberger

Three different physical techniques have been used to see through or probe into rocks, so miners might know what is ahead or overhead. These are radar, sonar, and a unique type of sonar called nonlinear sonar. Five radar systems have been developed. The highest frequency used is 4300 MHz for detecting small fractures at close range. This gives the best resolution. For longest range (over 2000 m, or 6560 ft) we use the 30 MHz radar for finding faults ahead of mining or ranging to salt dome flanks. Two types of salt, dome and bedded, are recognized. Radar works well in dry (dome) salt, but not in bedded salt which contains small amounts of water. The dipole moment of water absorbs energy from the radar. Thus was born the 30 MHz radar system and sonar probing systems. These can probe to 100 m (328 ft) even into wet salt. All probing systems measure data in time, which are converted to distance by measuring the time of travel of radar or sonar through salt pillars of known thickness. Ranges of probing in salt are from less than 1 m (3.3 ft) to more than 2000 m (6560 ft). Uses of radar and sonar probing in mines include mapping the top of salt above a mine; mapping salt dome flanks; finding impurities in salt such as anhydrite, sandstone, or potash stringers; locating old boreholes in salt pillars; locating fractures in salt; and finding faults or water zones ahead of mining.

Jan 1, 1985

By Jerome Alexander

It is an outstanding fact of Nature that many of the practical properties of substances are dependent, not on their ultimate chemical composition, but on the kind and degree of aggregation of their constituent particles. Thus, a granite boulder is unmoved by wind or water, but if reduced to a fine dust it will be blown about by the wind and washed away by the rain. Carbon in one crystalline state of aggregation (diamond) is the hardest known substance, whereas in another crystalline state (graphite) it is so soft that it is used as a lubricant. Laying too much stress on the mere chemical analysis of substances is apt to obscure the fact that the nature of the aggregation of their particles is always a factor of importance, and sometimes the most important factor. Colloid chemistry deals with matter in a very fine state of subdivision; its sphere begins with particles just a little smaller than a wave length of light and extends down until they blend into molecular dimensions. With particles of this size, such phenomena as surface tension and adsorption, which depend on the development of free surface, become enormously magnified. Thus a cube of 1 cm. edge has a surface of only 6 sq. cm.; but if it is reduced to colloidal dimensions by being cut up into cubes each having an edge of 0.01 µ (0.00003 mm.), it will yield one million, million, million (1,000,000,000,000,000,O~) such cubes, having a combined area of 600 sq. m., or 21,274 sq. ft. The tiny force with which a drop of rain clings to the window pane becomes a factor to be reckoned with, if the surface involved is increased millions of times. From the colloid-chemical viewpoint, metals and alloys may be regarded as jellies or sponge-like structures,. the viscosity or stiffness of which at ordinary temperatures is exceedingly great; and like all jellies their properties are dependent on the composition and degree of dispersion of their constituent phases. These, in turn, depend on chemical composition, mutual solubility, speed of chilling, subsequent mechanical and heat treatment, etc. In fact, in preparing metals and alloys for practical use, we remove undesirable constituents (as in the conversion of pig iron into steel), add desirable constituents (as in

Jan 1, 1919

By Kenneth J. Edmiston

The objectives of this paper are: to review the current status of chloride leach processes for sulfide concentrates, to make an evaluation as to the applicability of chloride leaching for replacing pyrometallurgical processes and to comment on recent advances in construction materials. The paper does not delve in detail on process chemistry. Sufficient references are presented on each process to allow the interested researcher to obtain process chemistry details. GENERAL The fact that chloride oxidates can solubilize base metals from sulfide concentrates has been known since the 1880's. The work of Hoepfner in 1902 was particularly accurate for its time with regard to the chemistry of chloride solutions. Recent work has dealt with the understanding of chloride extraction thermodynamics by modelling the behavior of metal chloride complexes. In the last several years several excellent review articles and symposiums have been issued covering chloride chemistry (1 thru 6).

Jan 1, 1984

By Robert L. Braun, Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides, chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 100° to 150°C. The rate of dissolution of chalcopyrite exposed to oxygen-saturated solutions becomes so rapid under these conditions that the rate of copper extraction becomes limited by the accessibility of chalcopyrite to the solutions. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, and size of ore particles. It is concluded that the high pressure and high temperature obtainable in a large ore mass broken by nuclear explosives promise the rapid and economic recovery of minerals not considered soluble by conventional in-situ leaching methods. The method should be broadly applicable to the kinds of deep deposits that must be depended on for future production and with minimum disruption of the environment.

Jan 1, 1974

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman' for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man' has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman's model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman' derives the constraint on the linked-central force distortion on the basis of application of Pauling's relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

By J. D. Lubahn

Prior tests by Dorn, where the strain rate in a tensile test was suddenly changed, have shown a small, but definite rate-history effect to exist. If this effect is neglected in the calculation of creep behavior from tensile results, an error should occur. This paper shows that this error is smaller than experimental scattering, and may be neglected. DORN1 has found a small but definite rate-history effect in the aluminum alloy 250 at liquid-nitrogen temperature using tensile tests with an abrupt rate change. Such an effect is to be expected from pre-viously known2-6 temperature-history effects, together with general experience that effects produced by changing the strain rate a large amount are simi-

Jan 1, 1959

By S. G. Malghan, J. P. Van Dillen

Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1984

By Corbett GJ

Magmatic-related low sulphidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar - sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.

Jan 1, 1995

Downtime cannot be tolerated on electric shovels whose cost may approach or exceed $400,000 each. The same may be said for larger-variety off-highway trucks which require an operational expenditure upwards of $50 per hour. One company, for instance, in order to ensure a more continuous operation, has specified centralized lubrication for all of its new equipment. In wet or dry weather, the mining of asbestos can place undue strains on machinery and other equipment. When the mineral is dry, its dusty, loose fibers work their way into crevices, and when wet, the glutinous asbestos may adhere to axles, gears and other wear components. Such conditions are multiplied during the extreme cold winters of eastern Canada. It is more difficult to lubricate and maintain equipment, and erosiveness becomes more punishing to wear parts. Resultant breakdowns rapidly drain off profits.

Jan 1, 1971

By A. U. Seybolt

DURING the course of an investigation of hot corrosion of nickel-base superalloys (combination oxidation-sulfidation attack at high temperature), it was considered possible that sulfur might gain entrance to the alloy in part, at least, by diffusion through the scale. Cr203 is nearly always observed as a prominent component of the oxide scale, and hence some experiments were carried out to examine the tracer diffusion of sulfur through Cr203 at 1000° C in the upper temperature range experienced by jet engine blades and vanes. Some hot-pressed Cr203 discs of quite high density were available from an earlier investigation1 on the rate of crf3 migration through Cr203. The Cr203 was 99.3 pct pure and contained -0.06 pct Fe as the largest metallic impurity. Additional data is given in Ref. 1. In this earlier work it was found that the rate of cation diffusion was independent of the atmosphere of thermal equilibration when using nitrogen, argon, or air, and also that the electrical conductivity of the hot-pressed Cr203 compacts was likewise independent of atmosphere in this range, thus indicating that the de-

Jan 1, 1969

By O. A. Kiehn, C. A. Born, F. N. Bender

Development of the flotation reagent scheme at Climax Molybdenum Company's mine at Climax Colorado is reviewed. Features of the mineralogy, milling practice and background of reagent changes are outlined. Special attention is given to the hitherto unpublished details of the application of depressants for copper and lead impurities. The present rougher flotation reagent scheme utilizes a neutral hydrocarbon oil, low in unsaturates and wax, as collector with a sulfated coconut oil emulsifier and pine oil frother. Lime and sodium silicate are used as rougher conditioning and slime dispersant agents. Chalcopyrite and galena impurities are depressed in both rougher and cleaner plants by stage addition of Nokes reagent and sodium cyanide to yield a metallurgical grade molybdenite concentrate containing greater than 90% molybdenite and less than 0.5%, 0.1% and 0.05% iron, copper and lead impurities, respectively.

Jan 1, 1976