Search Documents

By Y Li, B Shen, S Zhang

Jointed rock mass is often encountered in rock engineering and its stability has always been a major concern in underground engineering. To analyze the stress characteristics and their variations in jointed rocks, in this study, a new concept of sub-instability stage before rock failure is defined, and a new experimental method is used to investigate interaction between defects and intact rock of the jointed rock mass during the subinstability stage., Firstly, external characteristics of stress and failure mode of the whole jointed rock are investigated systematically by conducting uniaxial compression tests on red sandstone samples with a set of preexisting open flaws of different sizes, and the interactive damage of intact parts and defects in the subinstability stage was further studied. Secondly, rock-like material samples made of bonded plaster blocks were tested and internal data from stress sensor between the strong and weak segments were collected. The transforming processes from independent activity of the individual segment to overall interactive movement of jointed rock before the unstable failure were analysed. The test results indicated that the subinstability stage marked the beginning of interactive failure between the intact rock and defects. In the early subinstability stage, the relatively intact parts bore most of the load in a jointed rock mass, and the defects were damaged firstly which caused high strain around it. The areas of high strain increase rapidly, extending and migrating, causing damage to the intact parts. In the later sub-instability stage, the interaction effect reached its maximum, and a large number of cracks appeared in the intact rock and they propagated and coalesced. Intact parts experienced rapid failure and then the jointed rock failed. The experimental method used in this paper to identify the sub-instability stage could be used to identify failure precursors of jointed rock masses and to develop technology for disaster prevention in rock engineering. CITATION:Zhang, S, Shen, B and Li, Y, 2018. Experimental studies on interactive failure characteristics of jointed rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 453–461 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

G. SHERBURNE LAGERS (written discussion*).-Mr. Kennedy's discussion1 of Mr. Matteson's paper takes the form of a criticism of my own comments2 on this paper. Mr. Kennedy is a respected authority on matters pertaining to the salt-dome oil fields, and his characterization of my "elaborate figures" as "worthless" is sufficiently candid and comprehensive to warrant a brief reply. My "voluminous figures" consisted simply of a rough estimate of the minimum quantity of salt in the Humble dome, and a calculation of the volume of sea water and of the volume of saturated brine which this salt would represent. Mr. Kennedy apparently interprets my remarks as opposing the idea that so large a volume of salt could have been deposited from sea water, for lie cites the area and thickness of European salt beds; but nothing was further from my intention. Given an arm of the sea, an arid climate, and evaporation under a hot sun, it is easy to conceive the formation: of almost any thickness of bedded salt. I cited the figures in connection with Harris' theory of the origin of salt domes, according to which the plugs were formed by the deposition of salt from ascending brine solutions, owing to the drop in temperature as they neared the surface. I pointed out the well-known fact that the solubility of salt is only slightly affected by temperature, and that a drop of 80° C. would cause the deposition of less than one-tenth of the salt in solution; hence that more than ten times the volume of salt actually forming the plug must have been involved. If ten times the salt actually in sight be computed in terms of brine and multiplied by 50 or 60 to take into account all of the known salt domes, the resulting figure is so enormous that I am not at all as sure as Mr. Kennedy seems to be that the porous stratified rocks of eastern Texas and western Louisiana could contain or furnish so great a volume of migratory brine.

Jan 8, 1918

By Gustavo Coqui Barbosa

Neste trabalho, foi desenvolvido um modelo de elementos finitos para simular o primeiro passe da laminação a quente do trem acabador de tiras de aço C-Mn. O comportamento desse aço é definido por equações constitutivas que descrevem os mecanismos de encruamento e recristalização acoplados aos campos de tensões, deformações e temperatura. Foi implementada uma sub-rotina em linguagem FORTRAN disponível no programa de elementos finitos ABAQUS/Standard. O modelo foi estabelecido no estado plano de deformação por meio de elementos finitos com acoplamento dos campos de temperatura e deformação para o cilindro de trabalho e tira. As dimensões e condições de processo foram obtidas a partir de dados industriais do laminador de tiras a quente da CSN. O modelo prevê as distribuições de temperaturas e valor de carga de laminação em boa concordância com as medidas industriais. Os resultados do modelo evidenciam que há ocorrência de recristalização dinâmica durante o primeiro passe e, apontam que em determinadas regiões da tira a fração recristalizada dinamicamente chega a 100%. A análise de sensibilidade dos parâmetros do modelo foi feita para determinar o seu impacto nos resultados das simulações, notadamente na força de laminação e no tamanho de grão austenítico final.

Jul 30, 2018

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative ?In-the-Wet? technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully implement this technology.

Jan 1, 2013

By V. K. Banakar, R. P. Rajani, A. R. Chodankar

The Afanasiy-Nikitin Seamounts (ANS) in Eastern Equatorial Indian Ocean (Figure 1) are shown to be the exposed part of the presently buried 85°E Ridge system under the Bengal Fan sediment and were emplacement around 75-80 m.y. ago (Krishna, 2003). The first recovery of ferromanganese crusts from the ANS was made during 1994, and the samples (Figure 2) provided important clues on the evolution of this seamount (Banakar et al., 1997).

Currently all engineering schools face a common problem, an ever expanding technological base which must be presented to students within a fixed time period. Traditionally the programmes of study taken by engineering students destined for employment within the mineral industry include formal instruction in aspects of management to an extent greater than that presented in other engineering disciplines. Providing an adequate coverage of an expanding technological base within a fixed time span can lead to a reduction in the time available for 'non-technical' subjects, such as 'management'. This situation calls for periodic review of course contents and allocations of time. Following consultation with an Advisory Committee representing the mineral industry, mining research establishments, and kindred teaching institutions, the University of Melbourne has revised its mining programme. This programme is offered as an example of how aspects of management such as communications, economics, labor

Jan 1, 1980

By Forster I, Thilo A, Dean AK

A prototype production tool capable of operation in the hole sizes (

Jan 1, 1988

By Letícia Gomes Mathias Netto Lima

Propriedades mecânicas podem ser melhoradas por meio de tratamentos térmicos, isso foi demonstrado por meio de estudos ao longo dos anos. O tratamento criogênico tem demonstrado que pode melhorar as propriedades dos aços temperados e revenidos, ao se reduzir a presença da austenita residual e ao promover a precipitação de microcarbonetos. Nesse contexto o presente trabalho, pretende realizar tratamentos de resfriamento e criogenia, buscando melhorias nas propriedades de aços temperados e posteriormente revenidos. Foram preparados corpos de prova em aços SAE 4140 submetidos a tratamento térmico de têmpera (a 850°C), e após foi realizado o tratamento criogênico (-196°C) ou resfriamento (-82°). E por fim, as amostras passaram pelo processo de revenimento. O tratamento criogênico ou de resfriamento são procedimentos que costumam ser utilizados após o tratamento térmico de têmpera, estes consistem em submeter os materiais a temperaturas muito baixas durante períodos prolongados de tempo. Foi realizado ensaio de tração nas amostras já preparadas, assim foi possível realizar um estudo comparativo sobre as mudanças estruturais, morfológicas e mecânicas de um aço SAE 4140. Para as análises estruturais, morfológicas e mecânicas foram utilizadas técnicas de caracterização como microscopia ótica, difração de raios-X e microdureza.

Aug 16, 2017

By A. Boltax

The effect of cold work on the electrical and magnetic properties of solution-treated and aged Cu-Fe alloys was studied. The electrical resistivity of solution-treated and of aged Cu-1.7 wt pct Fe samples increased by up to 25 and 140 pct, respectively, follozcing a 55 pct reduction of area. The principle contributions to the increase of resistivity of the solution-treated and aged samfiles are examined. Measurements of the .saturation induction, coercive force, and stacking fault Probability are also reported. 1 HIS paper is the second in a series which examine the behavior of the electrical and magnetic prop- erties of Cu-Fe alloys. The first paper1 was primarily concerned with the effects of thermal treatment whereas the present paper examines the effects of cold work on solution-treated and aged Cu-Fe alloys. The effects of cold work on the transformation of the coherent fcc iron precipitate to the ferromagnetic form2 and the coercive force and remanence3 have already been described, but the unusually large increases in resistivity (up to 220 pct) which occlir with cold work have not been reported previously. EXPERIMENTAL METHOD The methods used for alloy preparation, heat treatment, and electrical and magnetic measurements are described elsewhere.1 The specimens, initially 4-in. lengths of 0.0625-in. diam wire, were cold worked by swaging in hardened steel dies. Following each reduction, the samples were etched lightly in hydrochloric acid to remove surface con-

Jan 1, 1962

By W. R. Phibbs

The blast furnace of the Columbia Steel Corpn., at Ironton, Utah, was put in blast April 30, 1024, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PeR Cent. Moisture................................................. 3.90 Volatile.................................................. 39.00 Fixed carbon............................................ 51.10 Ash............................................... 6.00 Sulfur................................................. 1.07 The analysis of the coke is: PeR Cent. Volatile.................................................. 0.55 Fixed carbon............................................. 89.70 Ash...................................................... 9.75 Sulfur................................................... 1.05 The coke is light and of a fingery construction, but is very fast burning. A screen test of the coke as loaded into the skip tubs at the furnace shows the following: Per Cent. On 2 in.................................................. 17.90 On 11/2 in................................................ 41.78 On 1 in.................................................. 27.80 Through 1 in............................................. 12.52 The by-product yields are as follows: Gas................................. 11,000 cu. ft. per ton of coal Sulfate............................... 30 Ib. per ton of coal Tar.................................. 12.65 gal. per ton of coal Motor fuel........................... 3.00 gal. per ton of coal Average B. t. u. in gas................. 567

By T. E. Leontis, J. P. Murphy

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By J. P. Murphy, T. E. Leontis

During the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,' in his treatise on magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 20' to 300°C. (68" to 57z°F.) and the results of Vosskiihler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Kei12 have also reported the creep properties of a forged magnesium-cerium-man-ganese alloy at 200' and 250°C. (392' and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554OF.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 per cent Mn have been found on the German BMW-8o1D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at at temperatures' The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The alloys investigated most extensively are

Jan 1, 1946

By Joseph A. Sutton

This study was undertaken by the Bureau of Mines to determine whether the sulfur-oxidizing bacterium Thiobacillus thiooxidans could use sulfur compounds to produce sulfuric acid in sufficient quantities to leach valuable metals from low-grade ores. The results of extended tests indicated that the bacterium is capable of extracting appreciable amounts of copper and cobalt from ore and mineral samples when sulfur is available in a state that can be readily assimilated by the organisms. Under the conditions of these tests, this organism was not able to assimilate and oxidize the sulfur as it occurred in the ores and minerals. Ores containing copper minerals in the silicate, carbonate, and oxide forms, in the presence of elemental sulfur, were more susceptible to bacterial action than ores containing copper minerals in the sulfide form. Thiobacillus thiooxidans remained active on elemental sulfur in the presence of some of the ores which were tested, but could not tolerate others. Therefore, strains of the bacterium were progressively adjusted to increasing concentrations (0.5 to 10 grams) of the individual ores until they could remain active on 10-gram portions of all ores being tested.

Jan 1, 1961

By Nicholas J. Grant, David S. Bloom

An investigation of the Cr-Ni system has revealed that there exists a eutectoid transformation at about 1180°C. 'The transformation in chromium implied by the eutectoid reaction was detected at about 100°C below its melting point. Associated with the eutectoid transformation, a metastable transition structure has been found. THE Cr-Ni phase diagram is shown in current literature to be a simple eutectic system in which the high chromium end of the diagram is incompletely determined, Fig. 1. The last investigation of this system was undertaken in 1936.' Because of limitations in metal purity, especially of chromium, and temperature measuring techniques, the diagram should be accepted with some reservations, as was indicated by Hansen.V or examwle.-, the wresence of the compound Cr²Ni, with a tetragonal structure," remains unverified and incompatible with the simple eutectic diagram. The work reported here began because of discrepancies that appeared in experimental studies in the binary alloys Cr-Ni and in the ternary system Cr-Mo-Ni. The existing binary Cr-Ni diagram failed to provide a complete explanation of observations made by microscope, X-ray, and thermal analyses. Experimental Methods The materials employed were of a higher degree of purity than were available to previous investigators. The Mond nickel used had a nominal purity of 99.87 pct, while the electrolytic chromium analyzed 99.03 pct with the major impurity being 0.5 to 0.7 pct oxygen with some iron. All alloys were melted in a vacuum furnace to remove dissolved gases, sufficient carbon was added to the charge to combine with all the oxygen as CO. Final analysis determined the carbon as about 0.02 pct and the oxygen around 0.06 pct or slightly more. Stabilized zirconia crucibles and thermocouple protection tips were used throughout and contributed no detectable impurity to the melts, as long as the oxygen in the chromium was kept low. Heats averaged about 250 g, which permitted about 2 in. of the thermocouple protection tips to be submerged. The temperature drop across the thermocouple protection tip was determined to be about 3°C, a minor source of error. The alloys, after removal from the vacuum furnace, were placed in a furnace operating in a purified argon atmosphere for the thermal analyses. An- nealed wolfram-molybdenum thermocouples provided the primary means of temperature determination, though a Pt-Pt-10 pct Rh couple was employed for a check when possible. A sensitive, high-speed Leeds and Northrup Speedomax recording potentiometer indicated the thermocouple output. X-ray diffraction patterns were obtained primarily on a Norelco unit, which permitted diffraction angles only up to 45" (28 = 90"). In general, either rotated or stationary solid samples were used, because it later evolved that many samples were susceptible to transformation resulting from the cold working involved in pulverizing. It was also noted that rotating a sample sometimes suppressed weak lines, so, usually, samples were not rotated. Later a high temperature camera was adapted for use at temperatures up to 1400 °C on the Norelco unit utilizing both solid and powdered samples. Unless otherwise noted, all X-ray patterns were made with a chromium tube and a vanadium filter. Further-

Jan 1, 1952

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

By R. W. Smith

A microorganism will function as a mineral flocculant if it is to some degree hydrophobic and can attach itself in some manner, such as through electrostatic interaction, to the fine mineral particles to be flocculated. The present paper concerns the use of a hydrophobic bacterium, Mycobacterium phlei, as flocculating agent for phosphate slimes. Experimental work on the flocculation of phosphate slimes and of dolomite and clay mineral suspensions was performed. It was found that M. phlei functions as an excellent flocculant for a dolomitic slime but does not function as well for mineral suspensions where large quantities of the solids are finer in size than the approximately 1 µm size of the bacterium.

Jan 1, 1992

IN the construction of a set of ordinary mine plans, two axes or coordinates are used; also, two different projections are essential viz., a plan (horizontal projection) and longitudinal section (vertical projection). In isometric projection three axes are employed-one axis vertical and the remaining two inclined to it at angles of 120°, also making an angle of 120° with one another, as shown in Fig. 1. The two inclined axes are used to plot the horizontal projection, while altitudes are plotted on the vertical axis. As an illustration, consider the ease of a simple object, such as a box. To show all the dimensions in the usual manner requires two drawings-a plan and elevation, as in Fig 2.

Jan 1, 1919

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014

South Africa remains the largest global producer of gold, accounting for 11.3 per cent of total world mine production, which amounted to 2520.2 t in 2005. The benefits and disadvantages associated with hedging practices in general, and among South African gold producers is examined. The wide variety and unique nature of risks faced by the mining industries provide a strong case for hedging. Only the principles of hedging, such as selling ounces of gold in the ground at a pre-agreed price for delivery at a future date as a cost-effective mechanism for price risk management, is discussed. Progressive and cumulative increases in the volume of forward sales in the major producing countries are considered by many to be the cause of the declining gold price over the past decade. In spite of negative publicity, forward selling continued as an industry-wide practice until recently (2002) when the global hedge book contracted by 352 t; contraction amounted to 158.6 t in first quarter of 2006. The objectives and benefits of hedging include continuity and stability of cash flows, stability in price achieved, reduction of frictional costs, and creating an effective management tool. The importance of a defined hedging strategy in reducing uncertainty about the hedging objectives is essential to a successful hedging policy. Historical patterns in hedging revenues at an industry level indicate five distinct periods during which the fortunes of hedgers have fluctuated. Finally, since 2001 the rising gold price and reduced price volatility through the consolidation in the global price means that the need to stabilize revenue flows is less urgent. This has meant that hedging is becoming progressively less important for the mining industry at large.

Jan 1, 2007

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984