Search Documents

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By Stefano Pirrello

"Sydney’s booming real estate market has pushed property developers to invest in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement Piles (DD) techniques are on the other hand suitable for these ground conditions. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West. The advantages of DD over CFA piles such as reduced overall spoil with substantial cost savings and achievable rock sockets in medium strength bedrock are discussed. Design validation through interpretation of real-time data from the piling rigs’ on-board computer data, and low and high strain pile dynamic testing (PDA) is discussed. Testing data is presented as CAPWAP (Case Pile Wave Analysis Program) analyses for different concrete grades.INTRODUCTIONThe booming real estate market in Sydney has pushed property developers in investing in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement (DD) Pile techniques are on the other hand suitable for these ground conditions and were utilised using concrete injection methods. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West.GEOLOGY & GEOTECHNICAL CHARACTERIZATION OF THE SITEThe Sydney 1:100 000 Geological Series Sheet shows that the site is underlain by man-placed filling and alluvial/estuarine sediment. The sediment comprises silty to peaty sand, silt and clay. Shell layers are also expected to be present within the soil profile. The Prospect/Parramatta River 1:2500 Acid Sulphate Soil Risk Map shows the site as ‘Disturbed Terrain’ in which soil investigations are required to assess acid sulphate soil potential. Several Cone Penetration Tests and Boreholes were carried out during the geotechnical investigation. All boreholes were extended to bedrock and NMLC-sized diamond core drilling was used to obtain 50mm continuous core of the rock, enabling unconfined compression strength testing to be carried out on selected samples. A summary of the ground conditions encountered on this site and inferred from the CPTs can be described as follows:"

Jan 1, 1900

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By McAllister J

Oxygen was in restricted use at Port Kembla until tonnage oxygen became available for steelmaking in the open hearth furnaces. In adopting the new process various modifications to furnace design and operation were necessary and some of these, including increase in roof height and variation in firing and draft control, are discussed.The design of oxygen lances is also discussed and various steelmakingtechniques considered.Steel production increased with oxygen roof lancing-one- furnace producing 8,507 tons in one week-but new problems, such as rate of refractory wear, and disposal of fumes, were created.Design of future open hearth oxygen furnaces is predicted.INTRODUCTIONIn the post-war era, the availability of "tonnage" oxygen caused a major revolution in steelmaking techniques. Various pneumatic processes showed that steel can be madeat a very fast rate and that oxygen steelmaking can be applied to open hearth furnaces. Methods used are surface impingement with roof lances, bath injection with door lances, flame enrichment with fuel firing, mixed gas and oxygen firing, and enrichment of normal combustion air by oxygen injection into the flue systems.Owing to its previous restricted availability and high cost, oxygen was used in rather small quantities in the open hearth furnaces at Australian Iron and Steel Pty. Ltd.(A.I. & S.), Port Kembla, until about the middle of 1960.At that time tonnage oxygen became available and roof lancing commenced on No. 33 furnace at No. 2' open hearth shop.

Jan 1, 1962

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management."

Jan 1, 2003

By Xue Wang, Callie Babbitt, Chelsea Bailey, Matt Ganter, Gabrielle Gaustad, Brian Landi

"Current trends, motivated by fossil fuel dependence and unprecedented greenhouse gas (GHG) emissions, show lithium-ion batteries (LIBs) emerging as a competitive energy storage technology due to higher power and energy densities compared to Pb-acid and Ni-metal hydride chemistries. These trends may be of concern, however, as environmental impacts are not well understood for either the LIB itself, or for the nanoparticles consumed or released during the battery's production, use, or end-of-life. This study combines economic modeling, dynamic material flow analysis, and fundamental material characterization methods in order to quantify some of the economic and environmental trade-offs for LIBs at their end-of-life. As expected, results show that as chemistries transition from Li-Co based cathodes to Li based Fe, Mn, and S cathodes, LIB recovery value correlates to the value of the raw materials used. These initial results aim to inform collection policies being proposed currently as well as enable future deployment of novel recycling techniques.IntroductionGlobal fossil fuel dependence and unprecedented GHG emissions have led to increasing attention on energy alternatives, for both electricity production and personal transportation. However, development of renewable energy systems is contingent on concurrent technological development of energy storage systems, primarily batteries used for power grid load-leveling, renewable energy storage, and hybrid and battery electric vehicles. In this sector, lithium-ion batteries (LIBs) are emerging as a competitive technology due to higher power and energy densities compared to lead-acid and nickelmetal hydride chemistries[!]. LIBs represent close to 20% of the total rechargeable battery market and 75% of the portable rechargeable battery market, which is the fastest growing segment of the rechargeable battery market, with a 20% global growth in 2008 [2].This surge in production ofLIBs indicates a looming waste problem; total waste from Li-ion batteries has likely grown substantially from the 500 metric tons estimated in 2003 [3]. Figure IA shows the substantial increase in world-wide lithium production that has occurred in the last several decades with batteries making up the largest share of applications (Figure lB). California and New York state legislators have attempted to proactively address this looming waste by issuing diposal bans on rechargeable batteries in their states[4, 5]. However, quantification of the costs involved in collection, transportation, and processing of these materials has not been examined in depth."

Jan 1, 2012

By David Winter

The geotechnical design, construction, and monitoring aspects of a tied back excavation 85 feet deep in Seattle, Washington are presented. The excavation was completed in overconsolidated deposits of sand, silt, and clay. Lateral soil pressures used in shoring wall design were the lowest to date for an excavation of this size in Seattle. Instrumentation data collected from hydraulic load cells and inclinometers were analyzed and are discussed. The data suggest the actual soil pressures felt by the wall were lower than the design values. Recommendations for future study, as well as future design modifications are given.

Jan 1, 1987

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

By James A. McGrath

"The predominant key word associated with all commercial blasting methods is “safety”. Safetyshould take precedent over all other aspects of the entire explosives industry which on a wholehas had an excellent track record as to number of injuries per unit of hours worked at all blastsites throughout our country."

Jan 1, 1999

By S Lukovic, Robert Briton, Calvin J. Konya

Investigators have reported that charges which are decoupled from the borehole wall produce different fragmentation then those which are fully coupled. The difference in effect could be as a result of energy doss during transmission across the air gap or it could be due to the change in detonation characteristics of the explosive as a result of the change in confinement on the charge during detonation. In order to better understand the phenomena of decoupling, a research project was conducted at the United States Bureau of Mines Station, near Pittsburgh, Pennsylvania. It was decided to use shock and bubble energy tests along with simultaneous velocity measurement to determine the mechanics of decoupling and energy transmission. Two explosives were selected for the test, one dynamite and one water gel. Test results indicated that decoupling could both boost the total energy output of the explosive and that further decoupling would drop the energy output.

Jan 1, 1987

By R. F. Mehl, M. L. Swanson, J. P. Hirth, G. M. Pound

The sorption of zinc in a-brass was investigated. By analyzing the elliPtically polarized light reflected from the surfaces of a-brass solid-vapor couples, their optical constants and surface compositions were determined. It was shown that the surface compositions approached an equilibrium value exponentially with time. The bulk diffusion coefficient, surface diffusion coefficient and condensation coefficient for a-brass solid-vapor couples were calculated near 350°C from the experimental results. It has been assumed during various diffusion experiments with bimetallic solid-vapor couples (Dunn,1 Seith and Kraus,2 Jenkins,3 Balluffi and Seigle,4 and others) that the surface composition of such couples reaches its equilibrium value immediately. Although this assumption is probably valid at elevated temperatures, it is certainly not expected to be confirmed at lower temperatures.* consequently, it was decided that a fundamental experiment, designed to solve this problem as well as to examine all aspects of bimetallic sorption, would be the investigation of the rate of approach to equilibrium of the surface composition of solid-vapor couples. The sorption (i.e., adsorption, absorption, and desorption) of metals is obviously dependent on the state of the metallic surface and substrate. Much recent theoretical8"9 and experimental10-12 work on condensation and evaporation of pure metals has shown that the surface contour in atomic dimensions is a critical factor in sorption, so that any deformation or contamination13,14 of the surface exerts a profound influence. It is also known that absorption or diffusion occurs much more rapidly along grain were and in other deformed regions. Thus an effective sorption experiment must utilize a strain-free and clean surface, or at least a clearly defined and reproducible surface state. A mechanically polished surface is in a highly deformed17-l9 state. Because the degree of this deformation is uncertain, it is clear that for most experimental purposes a strain-free (i.e., etched, chemically polished, or electropolished) surface is desirable. Although adsorbed gas molecules on metallic surfaces are unavoidable even in the highest vacuum,20 oxide films can in some cases be removed by suitable vacuum annealing. Electrolytically polished and annealed surfaces, being relatively without strain, smooth and free of bulk oxides, were considered adequate for the present sorption experiments. Measurement of the surface composition of a solid-vapor couple presents a unique problem. Since experiments to determine the approach to equilibrium of the surface composition must be performed at temperatures where diffusion is very slow, solute penetration is so small that conventional analytical methods are unsuitable. An optical reflectivity method utilizing a polarization spectroscope was employed because of the relatively small penetration (~200A) of visible light in metals. By this method, elliptically polarized light reflected from the metal surface was analyzed and compared with that reflected from samples of known composition. The a phase of the copper-zinc system was

Jan 1, 1962

By A. Steiner, E. Miller, K. L. Komarek

Equations have been derived to calculate the chemical potentials of the components of liquid binary alloys from liquidus and enthalpy data. The equations are applicable to systems with intermetal-lic compounds of limited solid solubility. The liquidus curve of the Mg-Sn system was accurately redetermined, and the melting point of the compound Mg2Sn was found to be 770.5° * 0.3°C. The thermo-dynamic properties of the liquid alloys were calcu -lated from the liquidus data. The activity of tin shows both positive and negative deviations from Raoult&apos;s law and the relative integral entropy is positive. THE phase boundaries in an equilibrium phase diagram are functions of the thermodynamic properties of the coexisting phases. Specifically, the shape of the liquidus curve near an intermediate compound is determined by the properties of the compound and the liquid phase. Hauffe and wagnerl have derived an equation for the chemical potential differences (ui) of the liquid alloys near the congruent melting point when the heat of fusion of the compound and the liquidus curve are known. In their derivation the temperature dependence of the ui value was neglected, and liquid of stoichio-metric composition was chosen as the reference state. To obtain chemical potentials over the ntire composition range of the phase diagram with the pure components as the reference state, equations have been derived which incorporate the temperature dependence of the chemical potentials. Such a thermodynamic analysis can be carried out when the liquidus curve and the enthalpy values are known. The equations have been applied to the redetermined liquidus curve of the Mg-Sn system to obtain the thermodynamic properties of liquid Mg-Sn alloys. The Mg-Sn phase diagram has been studied by various investigators and the results have been compiled and critically assessed by Hansen.2 Preliminary thermal analyses showed that the basic features of the diagram were correct. The system has one congruent melting compound, Mg2Sn, two eutectics, and some solid solubility of tin in magnesium. However, the published liquidus temperatures show considerable scatter. In order to perform an accurate thermodynamic analysis, the liquidus curve between the magnesium-rich and tin-rich eutectic compositions was therefore redetermined by careful thermal analysis using highest-purity starting materials. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd, Toronto, Canada) had a purity of 99.99+ pct with the following impurities (in ppm): 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu, <10 Fe; tin (Cominco Products, Spokane, Wash.) contained 99.999+ pct Sn. The graphite crucibles were machined from graphite rods (United Carbon Products Corp., Bay City, Mich.) which had an average total ash content of less than 30 ppm. All the graphite parts were baked out in vacuum at 950" to 1000°C for a minimum of 24 hr to remove volatile organic materials. The graphite crucibles (3 in. long, 1-5/8 in. OD, 1-3/8 in. ID) were tightly closed with a threaded cover (1/2 in. thick) which had a central thermocouple well (2-1/4 in. long, 5/16 in. OD, 3/16 in. ID). Cover and thermocouple well were machined from one piece of graphite. A thin sheath of quartz was inserted in the well to protect the thermocouple

Jan 1, 1964

By E S. B Santiago, C P. N Moreto, L V. S Monteiro, G H. C Melo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Iron oxide-copper-gold (IOCG) systems of the Carajás mineral province (Amazon craton, Brazil) are structurally controlled by regional-scale shear zones and have formed by multiple episodes of fluid circulation and hydrothermal alteration in the Neoarchean (2.71–2.68 Ga and 2.56 Ga) and Palaeoproterozoic (1.90–1.87 Ga).Collectively, fluid inclusion, boron, oxygen and hydrogen isotope data and Cl/Br–Na/Cl ratios in fluid inclusions reveal that regional circulation of non-magmatic brines (eg evaporative fluids/evolved sea water) and mixing with other fluid sources (eg meteoric or magmatic) is an important attribute in the genesis of the Carajás IOCG systems. The ?33S and d34S compositions of sulfides from the Neoarchean and Palaeoproterozoic IOCG systems suggest that the ore-bearing fluids have assimilated sulfur from crustal reservoirs. Nevertheless, most ?33S measurements have indicated mass independent fractionation (MIF) effect for both systems which points to the possible involvement of surface sulfur sources.CITATION:Xavier, R P, Monteiro, L V S, Moreto, C P N, Melo, G H C and Santiago, E S B, 2015. Non-magmatic versus magmatic fluids in the genesis of Archean and Palaeoproterozoic iron oxide-copper-gold systems of the Carajás Mineral Province (Brazil), in Proceedings PACRIM 2015 Congress, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By H. P. Leighly

WORNER1 briefly studied the embrittlement of titanium by mercury. He found that mercury will wet the titanium surface at 400°C in vacuo, if the specimen had been heated previously to 700°C to dissolve the oxide coating. Subsequent exposure to the atmosphere causes the mercury film to recede rapidly. Bending of the titanium specimen even after the mercury film has receded results in a brittle fracture. For the study of the embrittling effect of mercury on titanium, specimens 2 by 12 by 0.051 in. were cut from RC-130-A sheet, an alloy having a nominal 8 pct Mn content and a mixed a-ß structure. The specimens were stressed horizontally at a predetermined value after which a plastic ring having a cavity 1/2 in. diam by 1/2 in. deep was placed on the specimen. The cavity was filled with mercury and a hole was drilled in the specimen through the pool of mercury. If the stress level was high enough, fracture occurred instantaneously with the drilling. By repeating the test at different stress levels, the threshold stress can be determined. Mercury embrittlement causes a drastic reduction in the ultimate tensile strength of this alloy from 132,000 psi to about 15,700 psi. The drilling of the hole, in the absence of mercury, does not change the tensile properties. Fig. 1 shows the typical fractures observed as a result of the embrittlement of this alloy by mercury. The central portion of the fracture was brittle represented by the jagged region which appears to have occurred on the shear planes at about 45 deg to the stress axis. Ductile fracture, which is perpendicular to the stress axis, occurred near the specimen edges accompanied by a reduction of the specimen thickness. Examination of the fracture reveals that only in the brittle region does mercury wet the

Jan 1, 1962

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By Mohamad Omarei, S. M. Sadrameli

"The aim of this research work was to produce biodiesel (fatty acid methyl esters, FAME) from canola oil using KOH loaded on y-Al203 support as a heterogeneous catalyst. Different parameters such as effects of the molar ratio of methanol to oil, catalyst amount and reaction time on the yield were investigated. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were used for characterization of the catalysts. A biodiesel yield of 86.67% was obtained under catalyst preparation and transesterification conditions of calcinations temperature of 773 K, 4 h of reaction time at 338 K, and using 3.5 wt% catalysts and molar ratio of methanol/oil of 15:1. The leaching of potassium species in the spent catalyst was observed.1. IntroductionBiodiesel is an eco-friendly and alternative energy source for diesel engines that can be synthesized by transesterfication of vegetable oil or animal fat with alcohols [1 ]. There are four principal approaches to the synthesis of biodiesel involving the transesterification of the triglycerides of the plant oils and animal fats: base catalysis [2], acid catalysis [3-5], employing supercritical alcohol conditions [6] and enzyme catalysis [7]. The commonly used homogeneous catalysts are NaOH, KOH and their alkoxides. Homogeneous alkali-catalyzed transesterification is much faster than acidcatalyzed transesterfication [8]. However, a large amount of water is required to transfer the catalysts from the organic phase to a water phase after the reaction. Therefore, it is considerably more costly to separate the catalyst from the produced solution [9]. These disadvantages could be removed by use of a heterogeneous catalyst [10]. The use of heterogeneous catalysts eliminates the neutralization step, hence it results much easier to separate from liquid products. Also, they can be designed to give a higher activity and selectivity and to have longer catalyst lifetimes [11]. A large number of different heterogeneous catalysts have been synthesized for biodiesel production. For example, calcined Mg-Al hydrotalcites [12], zeolite and metal catalysts [13], metal oxides such as calcium oxide (CaO) [14], magnesium oxide (MgO) [15], zirconium oxide (Zr02) [16], and supported catalysts [17] have been investigated as heterogeneous catalysts. CaO and MgO are most frequently used heterogeneous catalysts for biodiesel production [18]. In this present work, we aimed at developing an efficient catalyst for transesterification of canola oil. We have prepared KOH/ Al203 by impregnation and applied to determine the optimum conditions for biodiesel production. Three different variables including reaction time , alcohol to oil molar ratio and catalyst loading with may influence the quality of the produced biodiesel were optimized. Moreover, SEM (scan electron microscope), XRD (X-ray diffraction) and XRF were used for characterization of the catalysts."

Jan 1, 2012

By Henry M. Howe

Henry M. Howe, Bedford Hills, N. Y. (communication to the Secretary.)*—Mr. Johnson&apos;s explanation, that the rounding of the graphite masses in oxygen-bearing cast iron is due to their being in part reprecipitated after re-solution in forming carbonic oxide temporarily with.that oxygen, is certainly most attractive and suggestive. It remains to be shown whether this rounding occurs also when the solidification is too rapid to permit this process to go on. J. E. Johnson might easily test this by casting a single ladleful of his oxygenated iron in masses of varying size. If this present hypothesis is true, then the rounding ought to increase progressively with the size of the casting, and with the distance from the outside, that is to say with the time available for re-solution and reprecipitation. I question whether a like benefit is to be expected even on this hypothesis, from the oxygenation of steel. The spheroidizing of graphite does good because graphite itself is so weak. But the constituent which can be spheroidized in steel is its cementite, which is a source of strength. Lamellar pearlite, in which this cementite in effect forms long den-drites, is far stronger than divorced pearlite, in which these dendrites have been broken up into spheroids. Even the surfaces of contact between ferrite and cementite are probably sources of strength because of the amorphous iron which probably fills them.

Jan 1, 1917

By J M. Gibbs

Craigmont Mines Limited mine 50,000 tons of ore and waste per day from the open pit at Merritt, British Columbia. An electric-powered "down-the-hole" drill, a diesel-powered rotary drill and two electric-powered rotary drills have been used. All primary drilling, as a result of cost and operating experience, is now performed with two electric-powered rotary drills. Trials with various loading techniques have increased the amount of AN-FO and decreased the amount of commercially prepared slurries used for primary blasting. Approximately 95 per cent of the primary blasting is accomplished with AN -FO, mixed at the hole. Introduction THE Craigmont mine is located near the village of Merritt, B.C., 240 miles northeast of Vancouver. The concentrator has been in production since September of 1961. Craigmont is a combined open-pit and underground operation. To date, slightly more than 95 per cent of the mill feed has been mined from the open pit. As underground development proceeds, the ore requirements from the open pit will decrease. The average milling rate from September, 1961, to April, 1964, was approximately 4,900 tons per day.

Jan 1, 1965