Search Documents

By Michael J. Marasa

"Geotechnical engineering and construction primarily relies on the subsurface characteristics of the particular site; however, obtaining both accurate and precise information on those features is challenging due to the numerous factors involved in testing procedures used to analyze varying site geology. This includes a detailed and thorough geotechnical investigation to understand the site conditions, allowing the implementation of the most practical and economical solution.This paper presents a case history of the installation of wick drains and construction of aggregate piers on the site of a large facility to be constructed in Memphis, Tennessee. Throughout intensive subsurface investigations, highly variable soils were encountered, requiring settlement control and increased bearing capacity. This paper will discuss the design and installation of the systems constructed, and procedures and execution of the work to ensure design specifications were achieved.BackgroundA 1.4 million square foot expansion directly adjacent to an existing 1.1 million square foot distribution facility in Memphis, Tennessee was planned to serve as a centralized facility for increased production. The first phase of construction included an 858,000 square foot warehouse and parking lot for approximately 400 trucks to the north of the existing structure. The anticipated column load for the warehouse was 125 kips; slab design bearing pressures ranged from 200 to 500 pounds per square foot (psf) and elevations ranged from EL. 264 to 282. Parking lot elevations ranged from EL. 264 to 290, requiring a design life of 10 years with an estimated 100 in- and out-bound trucks daily and maximum weight of 80 kips per truck. The second phase of construction took place east of the existing structure, and included a 794,000 square foot multi-level warehouse, a 100,000 square foot office, and additional employee parking. The anticipated column load for the second warehouse was 225 kips and slab design bearing pressures ranged from 200 to 500 psf. Elevations ranged from EL. 267 to 282. Anticipated column loads from the office were 25 125 kips, with slab design bearing pressures ranging from 100 to 200 psf. Due to the varying elevations within each planned footprint, up to 18 feet of new fill was required to match the existing structure’s finished floor elevation (FFE) at EL. 282."

Jan 1, 2017

By Ralph Arnold

IN OPENING the symposium under the auspices of the Petroleum and Gas Committee of the American Institute of Mining and Metallurgical Engineers, I wish to call to your attention the following, among other subjects, which it is hoped may receive proper attention: 1. The recording of as accurate an appraisal of the oil possibilities of the various countries as is possible, with information as to the immediate availability of their supply. 2. The development of further support for the move-ment to bring about active cooperation among Ameri-can oil companies in their foreign exploration and development work. 3. The furtherance of the efforts of the industry in securing governmental assistance in foreign oil develop-ment: (a) along the lines of a modification of our domestic oil policy, so that we can go to foreign coun-tries and consistently ask fair treatment as to royalties and bonuses; (b) by a closer cooperation between the State and Commerce Departments and the oil industry. 4. The calling of attention to the unjustifiably drastic action of the price-fixing group of the oil industry during the last year or so, with the hope that it will use gentler methods in the future. None of these subjects are new, and some of them have been discussed before various organizations for years. Our justification for again bringing them forward is the hope that by everlastingly harping on them the industry, the Government, and the people who shape the destinies of this country may some time, some how, realize their importance and take effective constructive action.

Jan 6, 1922

By C. S. Matthews, G. L. Stegemeier

In one field in South Texas, approximately 72 per cent of the pressure build-up results show a characteris-i.rtic "hump" (i.e., the pressure builds up and then falls off) which makes interpretation by. standard methods impossible Correlation of size and time of hump with formation permeability. well productivitv index, and method of completion led to the tentativc, conclusion that the humps were caused by segregation of gas and oil in the wellbore after closing-in"'. This conclusion was confirmed by performance of simple laboratory bubble-rise experiments, by theoretical bubble-rise time calculations, and by a detailed calculation of PVT behavior in the well of a particular well Oil which accurate Surface and bottom-hole pressure measure-ments were untile. The hump behavior has since been found to occur in many other fields. The cause, however, is not the mine in all cases. In some of these the hump is trace-ahie to leaks in the tnbing which allow influx from the annulus after closing-in. In other cases the hump is traceable to leaks in the device separating pay horizons in dually completed wells. It is concluded that the recording of both surface and bottom-hole pressures is desirable in wells which show an anomalous build-up behavior. A number of field examples is discussed where use of both sets of measurements enables the cause for anomalous behavior to he found, (and a reasonable interpreation of bottom-hole pressure to be made. INTRODUCTION Theoretically the pressure build-up in an infinite reser-voir should be a linear function of In [(t + at)/nere t is the production time and At a the closed-in time. Some of the variations from this behavior arc well known, such as the curved portion immediately after shut-in which results from after-production and skin effect, and the flattened end portion which results from boundary effects in a limited reservoir. The effect of stratified producing zones and irregular geometrical drainage patterns may also contribute unusual characteristics to build-ups. However, the effect of still another phenomenon—that of movement of fluids within the wellbore—has been neglected in most build-up studies to date. Fluid movements within the wellbore after shut-in occur as a result of after-production, packer failures, leaks in the casing or tubing, or buoyancy of the gas phase when both gas and liquid are present in the well. Each of these movements can influence the pressure build-up, sometimes sufficiently to negate use of the data for computing permeability or stabilized build-up pressure. Examples of each of these phenomena are discussed below. FIELD OBSERVATIONS ON HUMP BUILD-UPS In approximately 75 per cent of the wells in a medium-sized field in South Texas the pressure build-up curves rise to 3 maximum and then decline to what appears to be a stabilized reservoir pressure as shown in Fig. I. Similar behavior has also been observed in wells in other fields in Texas and Louisian:,. Because of the possibility of such behavior being a mechanical failure of the pressure bomb. the bombs were run in tanden into one well which had been known to exhibit this behavior. When both bombs recorded identical curves with the characteristic hump, it was inferred that the unusual build-up is a result of well or forma-

By P. S. Haury, Thomas C. Denton

"INTRODUCTION AND RESUMEThe Reward zinc property was one of the first selected for exploration by the Bureau of Mines at time when zinc supplies for war production were very short. Preliminary examination indicated that an appreciable tonnage of zinc that could be developed for early production might be found by diamond drilling. The geology was mapped by the Federal Geological Survey, and 14 holes were diamond drilled by the Bureau of Mines. This work was started in September 1942 and completed in September 1943.The Reward is an old property in southwestern Pinal County, 26 miles from Casa Grande on the Southern Pacific Railroad. Mining was begun in the early 1880's and was continued intermittently by several operators to about 1917. About 400,0oo pounds of copper was produced from the north¬eastern part of the property, mainly from a 600-foot incline in oxidized copper ore that replaced a bed of limestone. This ore was mined out. A 400-foot vertical shaft in the copper area was inaccessible. A 325-foot vertical shaft had been sunk near the southwest end of the zinc-bearing area, and a 600-foot crosscut tunnel had been driven near the northeast end of the zinc area, but little zinc ore was produced. There were several shallow inclines and numerous surface pits between the main workings.The ores were deposited in Paleozaic limestones that strike northeast and dip about 40 degrees northwest. These are capped by Cretaceous clastic and volcanic rocks in the zinc area. The outcrops show mineralization in a segment of the limestone 4,500 feet long, which is limited by large cross faults at each end. Another large fault, which strikes north, separates the northeast third of the mineralized belt from the remainder. Copper predominates northeast of this fault and zinc southwest of it. The ore beds are cut by numerous small cross faults. Ore was deposited for short distances along some of these, but more of it made out from the fissures along certain replaceable limestone beds."

Nov 1, 1946

By Irwan Halim, Bhoshaga Mitrran Ravi Chandran, Kevin Huynh

Tunnel segmental lining design constitutes a significant iterative process where modeling and numerical analysis are factors in deciding the number of segments, their dimensions, gasket placements, as well as the locations of dowels and bolts. Consequently, these modifications lead to revisions in the final drawing details. However, the current tunnel engineering practices lack systematic solutions that effectively bridge the gap between the iterative design process and efficient visualization of completed drawings due to the time- consuming nature of redrawing. This paper presents a pioneering application of AI-driven solutions including using Autodesk's API, for the Northside Interceptor Tunnel (NSIT) Project. It showcases the automation of drawing design and the real-time visualization of modifications, thereby streamlining the drawing process.

Jun 23, 2024

By K. L. Sehgal

Minerals are the basis of modern civilization: their exploitation and effective utilization are a yard- stick for measuring the comparative prosperity of different nations. This is particularly true in India where industrialization is just beginning to pick up speed. Production targets for our Fourth Five Year Plan (1966-71) are far ahead of the figures for, say, 1950 (the year we won independence) and show the extent of the expansion. Many problems remain to be solved, not least of which is the shortage of raw materials. India is no novice at utilizing minerals. Archaeological ruins at Harappa and at other historical places in the country show evidence of the fact that the ancient Indians not only knew the art of winning minerals from the ground over 6000 years ago-they were also well acquainted with metallurgy. Some of the present sites of mineral exploitation are the same as those our ancestors worked for many centuries.

Jan 9, 1965

By Bond. F. C.

Introduction Although autogenous grinding applications date back to the early years of mineral processing when tumbling-type mills were first used, there has been a renewed interest in this type of grinding over the past few decades. A review of the historical aspects of autogenous grinding is provided which follows the development of the various types of mills and processes. Wet and dry grinding operations using either autogenous or semiautogenous mills, including the Aerofall mill, are described. Em¬phasis has been placed on the test work required to evaluate the feasibility of using autogenous or semiautogenous grinding for a spe¬cific application. The factors which must be considered to establish the appropriate design criteria for these types of grinding circuits are discussed in detail. Successful application of these grinding circuits results from a thorough test program, a careful analysis of the test results, and a practical engineering approach to the design of the process flowsheet and milling equipment. Certain pebble milling applications, where the pebbles consist of the ore or rock itself, can be classified as autogenous pebble mill grinding, or better known as ore-pebble mill grinding. In the generic sense, pebble milling includes those grinding operations using a tum¬bling mill in which the grinding media consists of various types of pebbles, either ore or other pebbles, instead of metal balls. Conse¬quently, this subject is covered separately in Chapter 5, Pebble Mills. Operating data from many of the installations located throughout the world are included in this chapter. Our appreciation is extended to those companies who contributed this important information. History of Autogenous Grinding F. C. BOND Autogenous grinding, the grinding of ore by itself rather than by special metallic or nonmetallic grinding bodies distinct from the ore, has an old and honorable place in the art of mineral processing. It antedates the use of the rod mill and is only a few years younger than the development of the continuously fed rotating tumbling mill in which it is accomplished. Its history71, 72 is inextricably bound up with that of gold mining. Every important early development of autogenous grinding took place on ores of gold, except in one case of silver ore. In common with many other features of modern mineral processing, autogenous grinding would have been greatly retarded if the winning of gold had been so small a part of mining in the past as it is today. Gold unlocked the secrets of rock-on-rock grinding. In years past gold ores were crushed in stamp batteries and then flowed over copper plates covered with mercury which amalgamated the gold. The McArthur Forrest cyanide process for the dissolution of gold in a dilute alkaline cyanide solution appeared in 1890. With finer grinding it recovered more gold than could be won by amalgama¬tion alone. The first response was to stamp in cyanide solution and finer mesh screens guarding the stamp discharge. However, the fine screens greatly restricted the tonnage stamped, and they wore out rapidly. Rotating tumbling mills70, 73 were the obvious choice to grind the coarse product from stamps. Many of these were Gates tube mills; more than 1,000 of these were sold between 1907 and 1913. They were made in 6, 51h, and 5 ft diam, with lengths of 20 and 22 ft. The 5 x 22-ft size was the most popular. The term tube mill did not refer to the mill shape, but included all tumbling mills using grinding pebbles. The flint or chert rocks found along the coasts of Denmark and Normandy are probably the most durable and resistant to abrasive and tumbling wear of any on earth. They were much used in the early tube mills. The early linings were all silex or Danish flint blocks, cemented into place with portland cement. Local hard stones or cast iron blocks were also used later. The cast iron liners carried lifters and were not bolted to the shell, but were held in a tight circle against it by steel wedges hammered home between them. The first ribbed metal liners designed to hold grinding pebbles pounded into them by the mill action were developed at El Oro, Mexico, about 1905. These and the Forbes, Komata, and Tonopah types, as well as the Osborne type developed in South Africa within about five years, were very successful in reducing liner wear. They sometimes lasted two years or more, and equalled or exceeded the life of silex lining at a lower cost. Some of the types were patented. The pioneer name recorded in the history of autogenous grinding is that of Kenneth L. Graham. In 1907 at the Geldenhuis Deep Ltd. mine near Johannesburg, he ran a comparative test on two tube mills. One mill used pieces of the common gold ore, or banket, and the other used the customary imported Danish pebbles as grinding media. He published the first account of autogenous grinding.'' In a test lasting 81 days the ore pebbles showed a definite saving over the Danish pebbles. Graham's historic paper also describes the invention of B. Chew of the Crown Deep Mines of the first trammel to be attached to a grinding mill discharge. The first known account of autogenous grind¬ing printed outside of South Africa was the description of the Graham test in Mining and Scientific Press's The use of grate- vs. overflow¬discharge was also described at this time." The news of this successful test appears to have had immediate effect, for by the end of 1908 the number of tube mills on the Rand had increased from 72 to 120.76 Presumably, most of these mills were now using autogenous grinding. The ore was principally a hard conglomerate of quartz peb¬bles cemented by silica, and was eminently suitable for use as a grind¬ing media. It is unfortunate that in South Africa the new autogenous process continued to be called by its old name of pebble milling, since the name does not distinguish between grinding with ore and grinding with extraneous pebbles. For increased clarity the former is called rock pebble milling. The first historical stage in the development was what is now designated as secondary autogenous grinding, or rock pebble milling. It consists of grinding a feed all passing 'A in. or finer with ore pebbles about 2 to 4 in. in diameter. The next stage to develop was that now called intermediate autogenous grinding, where larger amounts of larger pebbles about 5 in. in size were used to grind ore which had been crushed to about rod mill feed size or somewhat finer. It was developed on the Rand and in other places where coarse stamp screens were used to increase mill tonnage. In many cases the early secondary and intermediate autogenous mills have now been replaced by conventional ball mills and rod mill-ball mill circuits, with the object of further increasing grinding capacity. The third stage to develop is designated as wet primary autogenous grinding, in which run-of-mine ore or a primary crusher product is all fed to the autogenous mill together. It developed many years later indepen¬dently in the United States and in South Africa. The fourth and most recent stage is that of dry primary autogenous grinding, which developed in the United States and Canada. All four stages originated in gold mining. The first use of commercial autogenous grinding outside of the Rand apparently took place five years later in 1912 at the Santa Gertrudis gold mine at Pachuca, 55 miles northeast of Mexico City. This was followed closely by an installation at Goldfields, Nevada, in 1914-1915. The first name associated with autogenous grinding

Jan 1, 1985

By H. F. Broicher

Introduction In April 1998, AIS Sommer GmbH of Germany delivered the first laser-induced fluorescence (LIF) analyzer to the mining industry. LKAB's Kiruna iron ore mine in Sweden shared the costs and the risk of building the prototype. This marks the beginning of LIF analysis as a technique for quality control in mining and mineral processing. Photoluminescence analysis is well established. In most laboratories, fluorescence spectrometers are standard equipment for quality or pollution control. LIF is being used in several applications, including combustion studies and particle image velocimetry. However, it has mostly been used in laboratory environments. The availability of rugged lasers for industrial use brings this powerful tool to the forefront of production, even in the rough conditions found in mining and minerals processing. Laser-induced fluorescence Basics. Fluorescence of naturally occurring minerals has fascinated man since scientific investigation of this phenomenon commenced about 200 years ago. However, importance in industrial application and peripheral activities. Hand sorting of ore under ultraviolet (UV) lamps is seen as an archaic method. Long gone are the days when geologists set out at night with UV hand lamps to find valuable ore deposits, especially those of tungsten. Today, fluorescent minerals are considered collectors' items and museum exhibits. In the late 1960s (Hemphill, 1968) and during the 1970s, attempts to use lasers for excitation of fluorescence in minerals led to the development of an airborne fluorosensor (Seigel and Robbins, 1980). However, this prospecting technology did not gain industry acceptance and vanished from the market. During the past seven years, ongoing research of the LIF of minerals resulted in new findings that give good reason to revive the interest in fluorescence and its use in the mineral industries (Broicher and Zydek, 1995; Broicher, 1998). Fluorescence is defined as the short-lived form of photoluminescence, in which matter emits visible radiation during and after irradiation with light – the fluorescence generally being of a longer wavelength than the irradiation. Fluorescence of matter is described by: • the absorption spectrum, • the emission spectrum, • the decay curve and • the quantum efficiency. The absorption spectrum shows the fluorescence intensity in a fixed spectral band as a function of the excitation wavelength, while the emission spectrum shows the fluorescence intensity at varying emission wave- lengths for a fixed excitation wavelength (Fig. 1). The decay curves describe the exponential decrease of the fluorescence intensity with time. The quantum efficiency is the ratio of irradiating energy to emitted energy. Re- cent research has found that: the quantum efficiency of minerals can be measured and evaluated,

Jan 1, 2000

By Katherine Mather

This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. Results of the properties of these rocks on their performance as concrete aggregates are discussed. CRUSHED stone classified as limestone comprises about 70 pct of the crushed concrete aggregate and roadstone produced in this country, and the product has amounted in the recent past to about 97 million tons per year, valued at more than $123,-000,000.' Therefore an evaluation of the properties of rocks classified in these statistics as limestones and an ability to predict their behavior as aggregate in portland cement concrete are matters of considerable economic consequence to producers and consumers of aggregate. This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. It also points out certain results of the properties of these rocks on their performance as concrete aggregates. The problems encountered in efforts to explain the behavior of limestones, dolomites, and related rocks as concrete aggregate lie on the frontiers between the ignorance of the geologists and the ignorance of the engineers. The mineral composition and textures of the rocks have not been adequately explored and described, and the effects of mineral composition and texture on the performance of aggregates have been worked out in only a few cases. There are instances of unsatisfactory performance and some generalizations of those experiences. There are many more examples of satisfactory performance than of unsatisfactory, but there is practically no published information as to why a particular aggregate was satisfactory in a specific use. There are all too few investigations of undeteriorated concrete; more is known about the pathology of concrete than about its normal structure and aspect. As part of the investigation of aggregates, the classification of rocks is not an end in itself, but is a step toward recognition of properties expected to influence the behavior of aggregates in their intended use. Rock of any type may perform well or poorly as concrete aggregate, depending on the physical condition of the rock, its physical and chemical properties as compared to those of the matrix in which it is placed, and the circumstances under which the concrete is exposed. Some classification and descrip- tion of the limestones is necessary to distinguish subgroups whose members will probably behave in similar ways and to evaluate the group as a whole. The group name, limestone, includes and tends to conceal the identity of rocks that have a very great range in chemical and mineralogical composition, structure and texture, conditions of deposition, subsequent history, and suitability for use as concrete aggregate. All the rocks classified as limestones include one or both of the most abundant rock-form-ing carbonate minerals, calcite and dolomite, as major constituents. Carbonate rocks is a more descriptive and more accurate group name than limestone, which has generally been used to include dol-omitic or magnesian limestones and dolomites as well as calcitic limestones. Classification and Description of the Carbonate Rocks The question of names to be applied to the carbonate rocks may appear academic, but it is of practical importance as long as there are specifications for aggregate that result in acceptance or rejection of rocks by name and as long as failure to make distinctions among the carbonate rocks leads to misunderstandings of their properties and of what may be expected of them in performance. Materials included in production statistics as limestone and tested for concrete aggregate as limestone range in fact from calcareous shale and calcareous or dolomitic sandstone and argillaceous limestone and dolomite to calcitic limestone and pure dolomite and to rocks close to calcitic and dolomitic marble. To take a simple example: consider two manufactured coarse aggregates, both dense and unweathered, one composed principally of crystalline calcite and the other of crystalline dolomite, but both known as limestone. If each is used as coarse aggregate in a standardized concrete mixture with the same fine aggregate used in both cases, made into concrete specimens, and tested in accelerated freezing-and-thaw-ing, the test results will probably be quite different, because of the differences in internal bond and thermal properties between the two aggregates. As long as both aggregates are called limestone, the test results cannot be explained, or used except in a very limited way; if the aggregates are distinguished as limestone and dolomite and the consequent differences in texture and thermal properties are recognized, the results are reasonable. Classification of the carbonate rocks used as aggregate should be based on structure and on composi-

Jan 1, 1954

By A. C. Galvis-Castro, R. Salgado, M. Prezzi, E. Ganju, R. D. Tovar-Valencia

It is generally accepted that the unit shaft resistance of piles in sands is lower for tensile loading than for compressive loading. So far, very little attention has been paid to the influence of the installation method on the tensile-to-compressive unit shaft resistance ratio. The objective of this paper is to analyze the effect of installation method on the ratio of unit shaft resistance in tension to that in compression for a model pile installed in a dense silica sand. To study installation effects, load tests on model piles were carried out in a half-cylindrical calibration chamber with digital image correlation (DIC) capability. The model piles were either jacked in one stroke using a constant rate of advance, or pre-installed into the dense sand samples. Digital images of the model pile and sand were taken during the load test and processed using DIC to obtain the displacement field in the sand. It was found that unit shaft resistance was essentially the same in tension and compression for the pre-installed pile, however for the jacked pile, the unit shaft resistance in tension was approximately half of that in compression. DIC analysis revealed that: (1) during the load test, more displacement occurs in the soil domain for the pre-installed pile compared to the jacked pile, (2) for the jacked pile, the magnitude of displacement in the soil domain is greater in tension than in compression and (3) for the pre-installed pile, the magnitudes of displacement in tension and compression are similar. INTRODUCTION Pile foundations can be categorized into two main types depending on the method of installation: displacement piles (e.g., jacked or driven piles) and non-displacement piles (e.g., bored piles or drilled shafts) (Basu et al. 2010; Salgado 2008). The response of these piles to loading can be studied in the laboratory by means of calibration chamber experiments on model piles that are either jacked into the samples, representing displacement piles (Jardine et al. 2005; Lee et al. 2011; Tovar-Valencia et al. 2018), or pre-installed in the sand sample, representing non-displacement piles(Galvis-Castro et al. 2019a; Le Kouby et al. 2013; Tehrani et al. 2016)

Jan 1, 2019

The OptiPit® software program is developed based on expertise gained at the Colorado School of Mines (CSM) using Mixed Integer Linear Programming (MILP) techniques. This program has been developed to satisfy the need in the mining industry for a multi-time period schedule and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving many dumps, stockpiles, complex processing options and blending requirements. The current software (or earlier development versions) has been beta tested and used on various large scale projects within Placer Dome Inc., Newmont Mining Corporation, and Phelps Dodge Corporation since 2003. Through the use of this software, these companies experienced additional value creation by optimizing mine sequences, cutoff grades, material process flows and stockpiles under complex operational and processing constraints. This paper will present simple case study results to demonstrate the power of OptiPit® when used as a cutoff grade optimization tool. Furthermore, the paper will show, by example, how significant the difference in the Net Present Value (NPV) of a given project can be, depending on whether results are obtained by way of cutoff grade optimization using OptiPit®, or by using traditional breakeven cutoff grade approach.

Jan 1, 2007

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By S. N. Aliferova, E. I. Afonina, S. N. Titkov, A. Ju. Bondareva, N. N. Panteleeva

"Potash ore is mainly processed using the method of cationic flotation. Potash ore deposits of the CIS, namely: at Upper Kama river, Gremyachinsk (Russia), Starobin (Belarus), Tubegatan (Uzbekistan) are characterized by relatively low KCl impregnation (1.0 – 1.5 mm) and contain up to 10% of waterinsoluble impurities (WII). Water-insoluble impurities are presented by aluminosilicate, silicate, carbonate (calcite, dolomite) minerals and anhydrite. In the process of milling the ore to a flotation size there are released and dispersed the insolubles impurities actively sorbing the cationic collector, i.e. aliphatic amines C16 – C22. In this regard there is carried out a preliminary desliming of the ore.Currently grinding the ore to a flotation size (1.5 mm or less) is carried out in rod mills along with forming of a large number of fine-grained ore fractions having the size under 0.25 mm, which results in the increased KCl losses with halite slime waste and reduction in the quality of finished product. There has been developed the technique for processing of potash ores with a high content of water-insoluble impurities (10 – 12%) containing, in different ratios, silicates, carbonates and anhydrite. The technology involves the use of the ore dry grinding to the flotation size and subsequent reagent activation of the processes for sludge removal and sylvite flotation.INTRODUCTIONCurrently there are being developed the potash ore deposits in the CIS countries, namely: at Upper Kama river and Gremyachinsk deposits (Russian Federation), Starobin deposit (Republic of Belarus) and Tubegatan deposit (Uzbekistan). Potash ores are a mixture of sylvite and halite and contain water-insoluble impurities of silicates, carbonates and anhydrite. The content of water-insoluble impurities (WII) reaches up to 10%, disseminated (impregnated) sylvite does not exceed 1.5 mm and in connection with that the ore is crushed to a particle size under 1.5 mm. Ore grinding is performed by wet process in rod mills with producing a significant amount of fine-grained mineral fractions and sludge, which are actively sorbing a cationic collector, i. e. primary aliphatic amines C16 - C22. The ground ore is deslimed and the slime product is directed to a sludge depot (pits)."

Jan 1, 2016

By AIME AIME

PRESIDENT Edwin Ludlow and Secretary Bradley Stoughton made their first-trip of the year 1921 to visit Local Sections of the Institute, and talk over Institute interests and policies, during the early part of April. The main purpose of the trip, as usual, was to bring back to headquarters suggestions or comments on the Institute's work on the part of, members. The trip was made a brief, one by the necessity of remaining in New Fork until Apr. 1, and of the attendance of President Ludlow at a meeting of American Engineering Council and. the organization of a Philadelphia Section of the Institute in Philadelphia on Apr. 16.

Jan 1, 1921

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By R. Pothina

The objective of this research was to develop a mathematical model for gyratory crushers to help in the prediction of energy consumption and to analyze dominant parameters that affect this energy consumption. The development of a gyratory crusher model was achieved in the following three main stages: mathematical representation and coding of the crushing process; building an amperage constant model to derive an energy-scaling formula; and modifying the amperage constant model to represent a full-scale model. Due to their significant influence on feed-size distributions, two blasting parameters, i.e., burden and spacing, were considered. The crusher parameters that affect energy consumption were also identified. A case study of an operating dolomite mine was performed. The results indicated that by changing the burden, spacing and crusher closed-side setting, the overall (blasting and crushing) costs could be reduced by 4.7% to 7.9% annually. It can also be concluded that burden and spacing values have a linear positive relationship with the crusher energy consumption, while closed-side setting values have an inverse linear relationship with the energy consumption.

Jan 1, 2007

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1893 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management ` 188, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Haward-Canfleld Bldg. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs, and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

By Frank M. Kimmerle

Spent Potlining (SPL) contains recoverable chemical elements (C, F, Na and Al) which are lost in stabilization or immobilization processes primarily aimed at eliminating cyanides and reducing leach rates of soluble fluorides prior to landfiling. They can be recovered in a variety of mineral forms for recycling in the aluminum industry and elsewhere. Alcan has developed a cost-effective hydrometallurgical route, combining a number of proven unit processes to destroy cyanides, recycle the chemical values and provide a zero-discharge process. Pilot plant studies of this Low Caustic Leach and Liming (LCL&L) Process prove that the fluoride scan be converted to acid grade fluorspar, while the sodium and aluminum are recovered as a sodium aluminate and caustic feed to the Bayer Plant operations. The remaining brick and carbon fraction constitutes a high ash solid fuel which meets TCLP leach criteria and whose reduced sodium content enhances its value as a chemical reducing agent.

Jan 1, 1994