Search Documents

By Leslie Gertsch

Outline First progress report ? ?Introduction ?Non-terrestrial mining ?Near-term targets ?Stages of mining ?Study procedure Capabilities needed for non-terrestrial mining ?Mining methods ?Mining unit operations ?Typical surface mine operations sequence ?Results to date General effects of gravity ?On fragmentation ?On excavation ?On transport ?Conclusions / Recommendations

May 1, 2013

By Kathleen Y. Knoebel

This paper describes a graphical mini computer system called MPASS 2 (Mine Performance Analysis/Simulation) which has been designed to conduct analysis of underground room-and-pillar mining operations using both conventional and continuous mining methods. Dynamic, graphic displays of mine face machine activities are presented on the CRT screen to provide extensive visibility into underground mining activities. MPASS 2 consists of: an interactive inputting system that graphically creates a room-and-pillar mine and describes the mine when production is initiated; a time-step simulator that produces statistical summaries of shift activities and uses CRT screen graphics for accelerated-time display of machine activities and delays; a statistical analysis subsystem for analyzing mine performance data; an industrial engineering system that permits users to enter actual machine activity statistics and replay mine operations on the CRT screen; and a data management system to store historical performance information on mine characteristics and operations. MPASS 2 operates on a Hewlett-Packard 9845B mini computer with 450 K bytes of extended memory, and is written in H-P BASIC. It has been installed at Freeman-United Coal Mining Company in West Frankfort, Illinois and at the U. S. Department of Energy Pittsburgh Mining Technology Center. Applications include production system simulation, industrial engineering analysis, production scheduling, new equipment evaluations, and training.

Jan 1, 1982

By Paul W. Jeran, Vladimir Adamek

Characteristics of surface deformations i.e., sub¬sidence, inclination, curvature and horizontal strains, are evaluated, based on information obtained by direct field measurements over three longwall panels in the Northern Appalachian Coalfield. Surface deformations have been precomputed using Bals' and Knothe's theories. The results have been compared with Bureau of Mines field data to evaluate the applicability of the two theories to the U.S. min¬ing conditions. Measured horizontal movements and the resulting horizontal strains differ as much as 300 percent from precomputed values. Topography has no detectable effect on vertical movements but appears to have substantial effect on the development of horizontal strains. The horizontal deformations computed from our field measurements generally exceed the limits used in other countries to protect surface structures.

Jan 1, 1982

By R. T. Jr. Faria, H. Vargas, R. Toledo, S. Cosin, V. P. Souza

"With the purpose of decrease environmental impact, caused by industrial residues (just discarded in the environment) and clay extraction in the ceramic industry, sanitary ware wastes were incorporated into clay. In contrast, it is important to evaluate not only the technological essays but also gases emissions in the ceramic firing process. The pollutant gases emitted in ceramic with residues can be in much larger concentrations than that in a pure clay ceramic firing or, on the other hand, can decrease the pollutant gas concentrations. With the aid of thermal analyses and photo acoustical techniques it was observed that sanitary ware waste can reduce the C02 emission. The gas emissions were shown as in function of firing temperature from 300 DC to 1100 DC. In order to analyze phase transformations during the firing process, clay samples and wastes were both analyzed by x-rays fluorescent chemical analysis and x-rays diffraction.IntroductionResearch works on the structural and physical changes that wastes, mainly industrially produced, cause to the final ceramic product has been rapidly expanding in these last two decades. See, for instance references in [1]. In spite of these examples of a continuous effort to incorporate wastes into clay ceramic motivated by technical and economical advantages, environmental issues are still a matter of concern. However, the gas emission due to the clay firing process and its related atmospheric pollution may be enhanced as a consequence of an incorporated waste [2]. It is known that the firing of clay ceramics in conventional furnaces using fuels such as wood, charcoal, heavy oil and natural gas generates appreciable amounts of gaseous components, mainly carbon dioxide (CO2), carbon monoxide (CO) and methane (CH4). Additionally to the atmospheric pollution, these gas sets could be harmful to the human health and can corrode equipments [3,4]."

Jan 1, 2012

By R. W. Brauchli

The author has made a statistical analysis of the relations between recovery and length of cores, diameters of cores and of drill pipe, and cost of coring under different contractual conditions. The data are presented in tabular form. The length of the core appears to play a minor part in the percentage recovered, with a tendency to lower percentages with increased core length; approximately 50 per cent of the length cored is normally recovered if the cores are more than 2 in. in diameter. The diarneter of the core has a more pronounced influence on the recovery; 1 3/8-in. cores average 29.1 per cent, 2 1/8 -in. core 53.4 per cent and 3 1/8-in. cores with 6 5/8-in. drill pipe 68.5 per cent. Where 31/8-in cores were taken with smaller diameter drill pipe, i. e., 4 1/2 - in. drill pipe in 8 1/4-in. hole, the recovery dropped to 49.8 per cent, indicating that the more rigid drill pipe favors good core recovery, a conclusion also borne out by the results obtained in using large drill pipe for smaller diame-ter cores. Surprisingly good recoveries were obtained from both the Johnson and Simpson sands; shale, limestone and dolomite each gave less then average recoveries. No serious fishing jobs resulted from coring operations. Attention is called to the need of a core drill which will make it possible to drill a full-sized hole while coring, and thus reduce the cost of cores. Data pertaining to core drilling should be consistently recorded, such as, diameter of drill pipe and collar, diameter of core, recovery, size of cutter heads, type of core-barrel, coring time, speeds of rotation and of pumps, weight on core-barrel, etc.

Jan 1, 1933

By H. A. Hamza, N. E. Andersen

Emulsions have long occupied an important position in many industries. In the petroleum industry, where enhanced oil recovery techniques such as steam stimulation, flooding, etc. are being increasingly practiced, emulsions are very frequently produced. Characterization of these emulsions are an important prerequisite for monitoring and evaluation of the recovery processes. Emulsion properties will also determine the type of treatment required to separate and recover the oil phase. A variety of laboratory, pilot-scale and field-generated emulsions were characterized. Coulter technique results for size analysis are compared with microscopy (image analysis) and laser light scattering methods; Coulter determined oil contents are compared with gravimetric and volumetric methods of analysis.

Jan 1, 1980

By Mohamed Hamoud

Relative permeability curves represent an important element of special core analyses, but challenges remain in obtaining valid results and the extrapolation and use of existing permeability results is problematic. This situation is compounded in cases where core properties are altered from changes in effective stress. During the production of oil and gas reservoirs, the effective stress changes as a result of changes in pore pressure or temperature. Therefore, changes in rock properties such as porosity and permeability will occur and will consequently influence reservoir performance calculations. An experimental program was carried out to understand the behavior of dense, reconstituted sand samples at low effective stress states. Drained triaxial compression tests were set up to study the effect of stress alteration on relative permeability data through porous media. Initially, a saturation stage was performed followed by isotropic loading to bring the core sample to reservoir fluid and stress conditions. Then, while axial (deviatoric stress) loading was applied to the sample, a series of absolute and relative permeability tests was performed under steady state flow at different levels of strain during pre and post peak shearing stress. The stress-strain behavior results from the study revealed that the absolute permeability decreased during isotropic loading (compaction) and increased during shearing (dilation). However, the shape of relative permeability curve changed from contraction to dilation and showed higher initial kro and the lower initial kro respectively. The goal of this project was to understand the behavior of both absolute and relative permeability at different stresses. It is expected that geomechanical processes will be adopted for special core analyses to support the current integration of geomechanics into reservoir engineering. This will be required if, during SAGD, conventional and/or unconventional reservoir simulation, reservoir engineers implement a proper set of relative permeability data at each in situ state of stress, instead of constant curves throughout the field?s life.

Jun 1, 2012

By Bryon Bisiaux, Walter Valery, Sonny Mwansa, George Amonoo, Adrian Dance

"Newmont Ghana Gold Limited’s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto-Mill projects, PTI’s methodology is termed Process Integration & Optimisation (PIO).Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit.Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended.A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI’s SmartTag™ system.The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material.This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput."

Jan 1, 2012

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Glatthar J. W, Lauder D. W, Manlapig E. V, Mackinnon I. R

The Ok Tedi copper orebody consists of porphyry and skarn orebodies. The skarn orebodies, identified by different mineralogies, are the source of high intermittent fluorine levels in the mill concentrates. This paper discusses the results of t

Jan 1, 1998

By Kim W. Wright

Introduction Mining operations require maps for each phase of project development. Engineering plans, cross-sections, and isometric drawings are also needed. Maps are used for geologic interpretation, reserve estimation, permitting, property acquisition, site studies, development work, and production. Maps and drawings are essential to mining. They provide needed information. Generating these products, however, requires many manhours. The filing and organization of maps and drawings is cumbersome, due to their size. Major map changes can necessitate the production of entirely new documents and, thus, additional manhours. The volume of maps and drawings generated in the life of a single project can be extensive. For example, some utility companies have data bases containing more than a million individual maps (one reported eight million). These problems were considered necessary evils in the past. Now, with the automation of map and drawing production, improvements can be realized. Computer-aided mapping and design offers a new approach for the production, management, and storage of drawings and maps. This approach promises benefits in time management, productivity, efficiency, and flexibility. In all economic projects, the bottom line is cost reduction. And implementing computer-based mapping and design techniques can lower costs and increase project profitability. AM/FM/CAD/CAM Automated Mapping/Facility Management (AM/FM) and Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) are becoming buzz words in the engineering world. Most relevant to mining are the concepts of AM and CAD. These terms relate to the application of computers, specifically computer graphic technology, to mapping and design. CAD refers primarily to the design of components and structures in two and three dimensions. But it can apply to the three dimensional modeling of mine workings, ore bodies, and geologic structures AM refers to the automation of conventional map production. AM/CAD systems use computers to store, manipulate, produce, and update drawings and maps in two and three dimensions. Ideally, the calculating capabilities of computers are also used in conjunction with design and drawing generation, offering capabilities not available with conventional, manual mapping and design processes. To better understand concepts associated with AM and CAD applications, the understanding of a few computer-related terms is necessary. Table 1 explains some of these terms. System Features The capabilities of AM/CAD systems are based on viewing transformations. These are the basic, manipulative tools by which AM/CAD packages generate visual representations of data. Examples include the rotation of a three-dimensional object through space, the expansion or contraction of maps to fit a given scale, enlargements of small areas on maps or drawings for detailed viewing, and the generation of cross-sections from three dimensional data. AM/CAD systems incorporate data base management in their architecture. This allows a user to modify, move, delete, or manipu-

Jan 6, 1985

By J Wu

Swirl Flow Technology (SFT), a novel approach for agitation in large industrial slurry tanks, was jointly developed and patented by CSIRO and Queensland Alumina Ltd (QAL). Currently, SFT is used in 16 alumina precipitation tanks at QAL, with the first installation in January 1997. This paper provides insight to the underlying fluid dynamics, which were investigated through pilot-scale experiments. A key finding was that SFT produces tank wall velocities approximately four times that of conventional draft tube agitator systems for the same power input, whilst for solids suspension, much less power is needed. SFT is energy efficient and practical in scaling suppression as demonstrated by the full-scale experience at QAL.

Aug 8, 2011

By P. E. Price, N. J. Grant

DURING the course of creep studies in iron-chromium-nickel alloys, it became necessary to establish the limits of the two-phase ferrite-austenite field at 1300°C. The shape of this region, predicted from the iron-chromium and chromium-nickel binary

Jan 1, 1960

By Gerhard Derge

The rapidity of oxygen steelmaking has created renewed interesl in the mechanisms and kinetics of the various processes involved. These studies can now be approached with increased confidence because of the more adequate thermodynamics, physical chernislry, and relevant engineering infornzation available. These combine to offer promise of useful control and automation if the details of each specific problem can be sufficiently well-defined. The hot filament microscope provides new insig-hi into many of these problems by direct observation at temperature, allowing the appraisal of the relative importance of thermal gradients, convection, and intermediate phases. All of these have a direct bearing on the overall rates and control of most pyrometallurgical processes. It is one of the special privileges of the Howe Lecturer to become better acquainted with this distinguished man. All of us interested in the metallurgy of iron and steel have developed some sense of his widespread influence by the annual reference to his work in these Memorial Lectures. Each lecturer since 1923 has been able to identify his personal specialty with the broad interests of Professor Howe. This has become even more rewarding with the background information from Professor Gensamer's monograph, "Henry Marion Howe's Contributions to Metallurgy, which brings out his happy combination of intellectual and professional activities. Beyond this, I found my personal bond with Professor Howe in his book on The Metallurgy of Sleel first published in 1891.' After a detailed discussion of the dephosphorizing action of slags, he relates the mineral species identified in the frozen sample to the chemistry of the fused slag with the question, "Is it not most philosophic to hold that these independent entities were wholly integrated in the initial magma; that their presence in it was wholly

Jan 1, 1968

By Hans-Christian Kurzweil, Klaus Mussger

CERN, the European Laboratory for Particle Physics, are upgrading their existing particle accelerator for the next generation of experiments and have three major packages of underground construction work in progress. Each package involves the construction of shafts, cavern, tunnels and surface buildings. This paper gives an overview of CERN, the LHC Project and a more detailed discussion of design process, design review and construction works of Experimental Point 5. The LHC works at Point 5 include two large shafts, two major parallel caverns with a total span of 50 m, which are separated by a 7 m wide and 28 m high concrete pillar, and a system of secondary tunnels and caverns. The overburden ground consists of around 50 m of water bearing moraine (silty, clayey gravels and sands) overlying 20 mof molasse, which consists of horizontally bedded marls and sandstones. The shaft shave been constructed with ground freezing, primary concrete lining, membrane and secondary slip formed concrete lining. The concrete pillar was then excavated and concreted in advance of excavation of the two caverns. Cavern construction includes primary support of shotcrete lining and rock bolts, followed by waterproof membrane and primary support of shotcrete lining and rock bolts, followed by water proof membrane and insitu concrete secondary lining.

Jan 1, 2003

By Richard C. Smith, Steven H. Brown

Commercial scale in-situ leach uranium facilities (i.e., solution mining) have operated since late 1975, and have begun to appear in increasing numbers in the last few years. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents, into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a mill. Milling is by conventional means, involving ion exchange, precipitation, calcining and packaging processes. This paper presents an overview of the solution mining process, and discusses an empirical method that has been used to determine the radon gas release rate in Bq (curies) per year for the overall operation of the facility including wellfields, milling processes and waste storage reservoirs. In addition to radon generation on the surface from radium decay, it has been determined that the major component of radon release is associated with the dynamic generation of radon from solutions returning from underground. Process parameters impacting this evaluation and the mathematical expressions developed are discussed. The preliminary data accrued is presented.

Jan 1, 1981

By Roy Rose, Bruce Bowles, Wesley L. Bender

Numerous large diameter water wells are used to dewater the pit at the Sleeper Mine. Occasionally, a well will be located inside the boundaries of a blast. Although one might expect that wells so located would become inoperable due to blast-induced damage, in most instances this has not proven to be the case.

Jan 1, 1991

By Reilly SY, Green TH, O&apos

Alkali feldspar meggacrysts are commonly found (with aluminous clinopyroxene, kaersutitic amphibole, titanomagnetite, ilmenite and apatite, and more rarely with zircon and corundum) in alkalic basalts and their derivatives as discrete crystals and fragments. They are commonly euhedral or subhedral and may be up to 15 cm in size. Their occurrence has been reported from many localities around the world, e.g., Africa, Antarctica, eastern Australia, eastern China, East Fife (Scotland), Eifel (Germany), Massif Central (France), Mongolia, New Zealand, New Mexico (USA) and Siberia (USSR). These megacrysts are relatively homogeneous and belong to the Na-rich anorthoclase group, although Kutolin and Frolova (1970) called them sanidine due to their monoclinic nature. The majority of megacrysts have a molar orthoclase content (Or%) between 20 and 30 (Fig.1). These anorthoclase megacrysts possess a high degree of disorder, with the structural state belonging to the high albite-high sanidine series (Hoffer and Hoffer, 1973; Chapman, 1976).Published interpretations of the origin of anorthoclase megacrysts fall into the following two categories: either (1) Anorthoclase together with the associated pyroxene and amphibole crystallized from basaltic magmas as phenocrysts (cumulate phases) at high pressure and the present host basaltic rocks are the parent magmas for the anorthoclase megacrysts (Binns,l969; Binns et al. 1970; Kutolin and Frolova, 1970; Hoffer and Hoffer, 1973; Laughlin et al. 1974); or (2) Anorthoclase probably crystallized from a more evolved liquid at relatively lower pressure and was then picked up and carried to the surface by a later

Jan 1, 1990

By Ralph B. Adair

The Bureau of Mines conducted laboratory batch and small-scale continuous tests on samples of silt from the Nolichucky Reservoir near Greeneville, Tenn., to develop a process for the recovery of commercial-grade muscovite concentrates. Using a combination of Humphreys spirals for preconcentration followed by cationic flotation, 94.5 percent of the muscovite was recovered in a product containing 96.5 percent muscovite.

Jan 1, 1971