Search Documents

The Taupo Volcanic Zone in New Zealand and the Philippine Mobile Belt in the Philippines are characterized by active subduction, active volcanism and high seismicity. The main factors affecting characteristics of geothermal systems in both countries are: tectonic setting, source magmas, maturity of the systems, and depth to the degassing magma body. Within New Zealand, geothermal systems are grouped into arc- and rift-type. Fluids in arc-type systems contain high amounts of volatiles (40%) and higher Cl contents (3,000-10,000 mg/kg). Maximum temperatures are also higher, reaching up to >400¦C. Arc-type alteration assemblages in New Zealand and the Philippines are similar. Because Philippine geothermal systems are less mature, have higher temperatures and steeper geochemical gradients than New Zealand ones, advanced argillization is more widespread occurring down to depths of 2000 m. Mineral phases are more varied due to the active input of magmatic waters and the formation of vapor conditions at depth, forming P04-, B-, Li-, Ce-, F-, and Cl-bearing minerals at high temperatures. In the Philippines, high temperature magmatic-hydrothermal to contact metamorphic assemblages containing biotite, amphiboles and pyroxenes are relatively common, but rare in New Zealand.

Jan 1, 1995

By T. Guilford Smith

In presenting the subject of " Armored Turrets for Coast Defense " to this Institute, I am indebted to the Gruson Ironworks, a company incorporated under the laws of the State of New York, for valuable information, model and plans, by which I hope to make clear the construction and peculiar merits of this class of gun-protection. I wish it understood, however, that this is not an undeveloped and untried inventor's ideal, but an advanced and fully perfected system, which has long since passed the experimental stage and has been adopted by most of the foreign governments, after years of extensive experimenting and the expenditure of millions of dollars. The present seems an appropriate time to present the matter to the scientific public, since, for the first time, it is possible to produce these turrets in this country, of American material, and made by American workmen, owing to an agreement entered into between the Gruson Iron-works and the Fried. Krupp Grusonwerk, of Magdeburg-Buckau, Germany, where they have hitherto alone been manufactured. Although its full development and present perfection have been attained at the German works, it may be of historic interest to state that the first idea of using a rotating protected platform for large guns originated with Mr. Theo. Ruggles Timby, a native of the State of New York, who filed a caveat in 1843 for a " metallic revolving fort, to be used on land or water, and to be revolved by propelling engines located within the same and acting upon suitable mechanism." This was followed in 1862 by the issuance to Mr. Timby of two patents (No. 35,846 and No. 36,593) covering the ideas described in his caveat of 1843. The first practical application of this system was made on the " Monitor," of Civil War fame, Mr. Timby receiving $10,000 for two

Jan 1, 1901

By R. W. Salmi

The authors discuss the cooperative efforts by Minnesota Ore. Operations and Research; from the earlier development, testing and installation of fine shear screens in the Minntac Step III concentrator to the most recent testing and operating data that has resulted in the installation of Derrick Multifeed sandwich deck screens in Minntac Steps I and II. Pilot-plant test results that were obtained at the Coleraine, Minnesota Research Laboratory are also reported and demonstrate the effects of feed rate and feed percent solids on sandwich screen performance with two sizes of Minntac fine screen feed.

Jan 1, 1984

By Thomas J. DeMull

Development of the Batu Hijau copper project was completed in the fourth quarter of 1999 with the formal handover and start-up of ore processing facilities. The project began in August 1996 when the owner, PT Newmont Nusa Tenggara (PTNNT), awarded an engineering, procurement and construction (EPC)contract to Fluor Daniel (FD) for the development of the project. This included a copper concentrator, port, power plant, town site and infrastructure. PTNNT managed the development of the mine and the procurement of the mine equipment. In 1996, Batu Hijau was the largest mining project ever undertaken. Developing the Batu Hijau Mine was complex. It involved the work of thousands of people in all parts of the world to plan, engineer, procure, fabricate and manufacture equipment, supply and deliver materials and equipment, and build the plant.

Jan 1, 2002

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By Martin S. Oudenhoven

This report describes the results of a Bureau of Mines investigation in which the stress concentrations and distributions caused by inclusions in a strained elastic plate were determined, Finite element analyses were made for 168 models containing single inclusions of elliptical, ovaloidal, and rectangular shape. The variables studied included: horizontal-to-vertical loading ratios, (Sh/Sv) of 0,0.33,0.5, and 1.0; width-to-height ratios (w/h), of 0.25, 0.5, 2, and 4; and Young's modulus of inclusion to Young?s modulus of plate ratios (K ratios) of 0.33, 0.5, 2.0, and 5.0. The results show that the theory for elliptical inclusions can accurately predict the average stress along the x and y axes of symmetry for circular, ovaloidal, and rectangular inclusions from the width-to-height and K ratios. The actual inclusion shape was insignificant, suggesting that the average stresses in other inclusions of irregular shape (orebodies) can be estimated with the theory for an elliptical inclusion. An application of this technique to mining problems is presented. The stresses in the elliptical inclusions were uniform throughout the inclusion for all the models studied.

Jan 1, 1972

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By J L. Mauk

The Martha epithermal Au-Ag deposit contains multiple generations of quartz veins with a range of textures. We examined: +        vein textures, +        crosscutting vein relationships, and +        the paragenetic sequence within the pit walls as well as a wide range of hand specimens. Samples include host rock, breccia, and veins, but these groups are not distinct; instead, they form a continuum.   Veins at Martha mine show a wide range of textures on a local scale; these textures also change significantly over both the lateral and vertical extent of the pit. Common textures include crustiform bands, comb quartz, colloform bands, platy quartz, massive quartz, drusy quartz, sedimentary textures and brecciation.   Vein grades relate to textures. Many textures, including crustiform, platy, cherty, and sedimentary textures display predominantly low grades, but some textures are linked with high grades, such as ginguro, massive and comb quartz where they are associated with visible base metal sulphides and/or electrum. Host rocks and most breccias are low grade, as most samples contain <2 ppm Au.

Jan 1, 2006

By Omer F. Usluogullari, C. Vipulanandan

"It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength.In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.IntroductionIn-situ tests are increasingly used to determine the soil properties for geotechnical analysis and design of deep foundations (Ampadu and Arthur 2006; Hsu and Huang 1999). Static and dynamic penetration resistances have been used to classify and characterize subsoil (Ahmadi et al. 2005). The penetrometers evolved from the need of acquiring data on subsurface soils that could not be easily sampled by any other method. Laboratory testing undisturbed samples requires great care to avoid disturbance during handling, or systematical disturbance during testing, and it may be difficult to relate the laboratory test results to the in-situ properties of the soil (Sanglerat 1972). There is always a certain degree of disturbance to the samples because the confining pressures, which exist in the ground, are forcibly changed when the sample is collected."

Jan 1, 2017

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By Fred C. Bond

COMPRESSION TESTS THE standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of crossectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a high-speed steel disk with diamond dust embedded in the edges, and running under a water spray. Such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding planes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing Co., and are listed alphabetically in Table 1. These tests were made on one inch cubes or on diamond-drill cores approximately one inch in diameter and one inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. Compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test No. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TVA quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1946

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

During the latter part of 1937 consideration was given to the construction of a; local smelting plant for producing blister copper. Previously copper concentrates had been shipped to the United States of America. The proposition had the advantages of a saving in cost of realization, quicker financial return and reduced dependence on overseas shipping.The smelter was designed by the existing staff, who had difficulty in obtaining data on small plants, particularly on the reverberatory furnace. Construction was started in March, 1938, and the reverberatory was blown in on January 16th, 1939. One roaster had been operating for several weeks prior to this date.While results and operating technique on this new departure in small-scale smelting are barely beyond the experimental stage, it is felt that the experience gained to this time should be recorded to help fill the obvious gap in published information covering plants of this type.At present there are three copper smelters operating in Australia; the other two plants are equipped with blast furnaces.LOCATIONThe new smelter is situated in a position convenient to the concentrator and to the power plant. The site is traversed on two sides by a brick flue, from an old smelter plant, which connects with a 250-ft. stack. This stack and portion of the old flue are used in connection with the...

Jan 1, 1939

By Jr. Herty

Ferromanganese continues to be an indispensable requirement in steel manufacture. Approximately 470,000 of the 80 per cent ferro-alloy was consumed in 1929 and increasing amounts will be required annually by the steel industry unless some satisfactory substitute is found. An average of 14 pounds of metallic manganese is used for each ton of steel produced, The principal use of manganese is for de-oxidation of the metal in the steel refining processes, although a considerable amount is also used for the production of special manganese steels. Unfortunately, domestic production of manganese ore is inadequate to meet normal peace-time requirements, not to mention increased abnormal war-time demands. The rather large quantities of low-grade manganiferous iron ores which occur in the Coruna Range in Minnesota have for a number of years greatly appealed to those interested in the development of a domestic source of the supply. The North Central Experiment station of the Bureau of Mines has made an elaborate study of the possibilities of the pyrometallurgical treatment of ores from these deposits and much of the valuable information secured by them has already been published.

Jan 1, 1930

By White L. R, Boger D. V

The paper describes the surface chemistry and particle physics that control the fundamental flow properties (Theology) of mineral particle slurries. We further address, through a series of case studies, the design data that emerges from experimental studies of the flow properties of complex, high volume fraction mineral slurries. The case studies are drawn from mineral oxide concentrate processes, tailings dewatering operations and from filter cake production and management. The paper emphasises the essential links between design of process slurry handling systems and the control of the flow of such slurries by control of the pulp chemistry.

Jan 1, 1992

By Yucheng H, Baogui Y, Wenyong L

High-water rapid-solidifying material, called 'high-water material', is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of hackfill body. environmental contamination and so on, have been solved.

Jan 1, 1998

Jan 1, 1963

The Telfer Gold Mine, owned and operated by Newcrest Mining and located in Western Australia, is currently being expanded. A new underground sublevel cave development is proposed along with an appreciable expansion of the open pit. The Telfer area is generally subject to low rainfall, however, during the wet season cyclonic events can result in sizable rain events, which have the potential to cause substantial inflow. In addition to this, during the first five years (nominal) of the mineÆs life, there is the potential for drainage paths between the pit and the underground mine via decommissioned underground workings which lie directly under the pit. After this initial five year period the pit floor will be mined out below the old workings and will therefore no longer connect to the underground, however cave breakthrough to the surface may start to occur thus providing another water path into the underground mine. To arrive at an optimum, safe solution for dewatering the mine that successfully addressed the above items, a rigorous risk analysis was included as an integral part of the design process. This involved the determination of the probability of events occurring and the consequences of these occurrences. This was compared against the cost of mitigation for the various events. This paper outlines the process by which a safe concept addressing all the issues relating to dewatering the proposed mine has been arrived at. This process included: Establishing the pit catchment areas. These were based on historical run-off data and took into account practical mitigation works. Establishing an Average Recurrence Interval (ARI) based on reference material and historical rainfall data. Utilising a standard approach based on Australian Rainfall and Run-off (ARR) to calculate pumping and storage requirements for the various catchments. Analysing the 20 years of recorded rainfall in the Telfer area to establish the duration, magnitude and sequence of events. This analysis assisted in determining the surface run-off coefficient. Establishing potential water storage areas and determining the risks associated with using particular storage options. Establishing the percolation rate through the cave zone. A degree of uncertainty regarding the percolation rate in the cave zone required that the consequences of using various percolation rates were considered to aid in establishing the rate which was adopted. Establishing preliminary concepts and determining the most economically viable concept. Conducting a risk assessment based on the principles outlined by Australian Rainfall and Run-off (ARR) to confirm that the appropriate Average Recurrence Interval (ARI) had been selected. A risk assessment was also conducted in accordance with client requirements. Establishing the optimum pump station sizes and storage capacities. Establishing the appropriate numbers of duty and standby equipment. By using the foregoing process, which included a number of stages of risk analyses, an optimum dewatering system concept was produced.

Jan 1, 2003

By N. D. L. Burger

An effective prototype face support system to minimize rockfalls in rockfall-prone mines was developed and patented during a project sponsored by the Mine Health and Safety Council (MHSC). An experimental development model (XDM) roof support unit was developed and evaluated. Mines with rockfall problems in the face areas can use the roof support system to reduce fatalities and injuries in the face area of stopes. The roof support system consists of two similar support units connected to each other via two crank mechanisms. Each unit consists of a headboard supported by a ?wishbone? structure (top and bottom leg). In the first design a threaded bar with struts similar to a scissors jack keeps the legs apart. (In the final version that was field trialed, the threaded bar mechanism was replaced with a hydraulic cylinder). All the components are manufactured from steel. To move the system forward the first support unit is collapsed, the second remaining in the loaded position. The first unit then hangs from the second unit to which it is connected. The first collapsed unit is then manually cranked forward and prestressed. If the required position is still not achieved, the other unit is released and moved forward. The specification for the system was determined and presented at a workshop with industry participants. Different concepts were developed and evaluated against the system specifications. A technology demonstrator was then developed and tested on surface. The technology demonstrator development process included detail design, building and testing of components and subsystems, design reviews and the building and commissioning of the technology demonstrator. The testing of the technology demonstrator was done in a 500-ton hydraulic press, in a mock-up stope and underground. A risk analysis, in which technical, logistical and economic aspects were assessed, was done to determine the critical areas of the system. During the next phase of the project working prototypes were developed for underground tests and evaluation. This process indicated that it was necessary to adjust the system specifications and a redesign was called for. In an iterative process test units were built for purposes of evaluation, specification verification and field trialing. After the successful conclusion of the trials the equipping of a complete production stope started for purposes of integrating the system into the current mining process.

Jan 1, 2008

By Haizea Arratibel, Diana Méndez, Jhuliana Macas, Michelle Peñaherrera

La forma en la que las empresas ingresan a un territorio sienta las bases para las dinámicas de relacionamiento a futuro. El diálogo multiactor es una herramienta que permite, desde un inicio, formar relaciones de confianza y acción colectiva, pasando así de una dinámica transaccional a una transformacional. Esto alcanza resultados que van mucho más allá de la gestión de conflictos, enfocados a crear un territorio sostenible bajo un modelo de gobernanza sólido. Se presenta el caso del proceso de diálogo multiactor en Los Encuentros, Ecuador, bajo el marco del proyecto Fruta del Norte de Lundin Gold.

May 10, 2023