Search Documents

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Only grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own.CONCLUSION• Overflow versus grate dischargeAn overflow mill has a “pool” of slurry around the toe of the ball charge, which creates a counter lever to the ball charge. This will reduce the absorbed power in the range of 10-15% (depending on the case) and will consequently result in a coarser grind. The tests found a 4% gain in grinding efficiency (Wio) with an overflow mill but this is probably not significant.This lower absorbed power and coarser grind can be counteracted by increasing the ball charge (if below maximum) and/or by increasing the mill volume when removing the grate discharge (a typical grate takes up about 300mm of the mill length).• Open versus closed circuit"

Jan 1, 2003

By G. J. Wolga, W. W. Tyler, A. C. Wilson

THE physical properties of uranium have been reviewed by Katz and Rabinowitch.1 Their review includes thermal conductivity data for ternperatures above 375°K. Recently, Mendelssohn and Rosenberg' have published data on the thermal conductivity of uranium from 2" to 20°K. Our measuremerits indicate the temperature dependence of the thermal conductivity in the temperature interval from 20" to 300°K. Electrical resistivity and thermoelectric power were measured on the same sample. The material studied was normal uranium which had been heated at 700°C in a lead bath for 10 min and then quenched in a water bath held at 50°C. From this material a rod M in. in diameter and 2 1/2 in. long was machined. Two 0.040 in. holes were drilled into the rod 1 3/4 in. apart. Copper-constantan thermocouples for temperature and potential measurements were soldered to copper pins which were pressed tightly into these holes. Details of the equipment and experimental techniques used in making the measurements have been described elsewhere." Fig. 1 shows micrographs of a section of the sample studied. Fig. la was taken with unpolarized light and shows impurity inclusions, probably uranium carbide. Fig. lb, showing the same field, was taken with polarized light and gives some indication of the grain size and twinning within the grains. Experimental Results Thermal conductivity and electrical resistivity data are shown in Fig. 2. Table I shows values of

Jan 1, 1954

By Cleland N. Conwell

Intermittent coal mining has been conducted in Alaska for over a century. The first report of coal in Alaska was by the Veechy expedition of 1826 and 1827. Whaling ships used coal from Corwin Bluff near Cape Beaufort during the early and latter parts of the 19th century. The first coal mine in Alaska-and probably the oldest in the Pacific coast of North America-was opened by the Russians at Port Graham on the southwest tip of the Kenai Peninsula. The mine was operated from 1855 until 1867 when the United States took possession of Alaska. From 1880 to 1915 coal mining was carried on intermittently at several localities including Unga Island, Herendeen Bay, Chignik Bay, Kachemak Bay, and several points along the Yukon River. Small coal mines along the Yukon River provided fuel for the river steamers traveling from St. Michaels to Whitehorse. The area of sustained coal production began with the completion of the Alaskan Railroad from Anchorage to the Matanuska coal field in 1916 and to the Nenana field in 1918. Coal production continued to increase until 1953, at which time the oil and gas fields in Cook Inlet were developed. Oil and gas eventually replaced the Matanuska coal as a means of providing heat and power. The military in the Anchorage area shifted from coal to oil in 1967 causing a decrease in production. The increased demand for electric power in the Fairbanks area offset the decline and coal production started to increase. In 1969-1970 the Golden Valley Electric Assn. (GVEA) constructed a mine-mouth power plant 70 miles southwest of Fairbanks near Healy and a power line to Fairbanks. Location of Coals in Alaska Coals are found in all geographical subdivisions of Alaska. Coal in Alaska ranges in age from Carboniferous to Tertiary, and grade from lignite through anthracite. Fig. 1 shows the locations of Alaskan coal fields. The only fields that have been developed extensively are the Matanuska and Nenana. Fig. 2 illustrates the annual production of coal in Alaska and the ratio of underground to strip mining.

Jan 1, 1973

By Jamal Rostami, Alireza Salimi, Christian Moormann

"Rock mass classification systems are often applied in many empirical design practices in rock engineering, some contrasting with the original intent and applications of these classification systems, for example, estimation of TBM performance in various ground conditions. While accurate estimation of machine performance is significantly impacted by rock mass properties, parameters used in many of the existing classifications are more related to ground support design and not rock mass boreablity. The results of many investigations on this issue have shown a weak correlation between TBM rate of penetration and rock mass classification. This limitation can be overcome by fine tuning the rock mass classification input parameters to represent influence of rock mass properties on TBM performance as has been the objective of RME or QTBM. This paper will offer an overview of the impact of rock mass on TBM performance and introduces an empirical equation for predicting performance of rock TBMs based on rock mass classification. The results of the preliminary analysis of a new model has revealed that the use of the proposed system can offer a reasonable accuracy for estimation of TBM performance in various rock masses. 1. INTRODUCTION Hard rock tunnel boring has become more or less the standard method of tunneling for tunnels of various sizes with lengths over 1.5–2 km. Estimating the performance of TBM is a vital phase in tunnel design, and for the choice of the most appropriate excavation machine. During the past three decades, numerous TBM performance prediction models for evaluation of TBM rate of penetration and advance been proposed. In brief, all the TBM performance prediction models can be divided into two distinguished approaches, namely theoretical and empirical ones (Rostami et al., 1996). The most common and recent works on this topic are summarized in Table 1. Currently, two models including Colorado School of Mines or CSM (Rostami and Ozdemir, 1993; Rostami, 1997) and Norwegian University of Science and Technology or NTNU (Blindheim, 1979; Bruland, 1998) models are the most recognized TBM performance prediction and prognosis models in use around the world."

Jan 1, 2016

By Mariana Boger Netto

O fósforo é um elemento crítico para a qualidade dos aços, tornando a redução dos teores desse elemento uma exigência para a indústria siderúrgica. Uma forma de se medir a eficiência da desfosforação é através do coeficiente de partição do fósforo (Lp=%P(escória)/%P(aço)). O objetivo principal deste trabalho é avaliar escórias de um forno elétrico a arco através da comparação entre o Lp real com o Lp calculado por simulação termodinâmica, avaliando, também, o comportamento da partição de fósforo com relação à composição química. A partir de dados de composição química de amostras de escória e aço de uma usina siderúrgica, foram feitas simulações termodinâmicas utilizando o software FactSage. Com base nesses resultados, concluiu-se que o cálculo computacional através do software descreve bem o comportamento termodinâmico, mas tende a superestimar o Lp, provavelmente por questões cinéticas e/ou de transferência de massa e calor.

Aug 17, 2017

By William H. Breeding

The remarks that follow are based substan¬tially on experience covering 45 years, 80% of which have been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more-difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1 ½ . The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present.

Jan 1, 1984

By Donald Bishko

Zoning is the legal means by which land use can be controlled. Although zoning laws have historically been quick to prevent quarrying, one is hard pressed to find zoning ordinances which specifically state that land should be used (or held in reserve) for quarrying and prevent other uses such as recreation, housing, etc. This situation is especially true when the mineral to be quarried has a low intrinsic value such as sand, gravel, and crushed stone. The chance of a gold mine surviving urban sprawl is probably considerably greater than that of a sand and gravel pit, even though it is possible that the dollar value of the sand and gravel' would exceed that of the gold mine. The research reported herein was concerned with two major topics: to delineate the real costs associated with the non-protection of our construction aggregate resources (growth minerals) and to develop a computer simulation model which would aid planners in making economically sound decisions. This paper describes the problems faced by the mineral aggregate industry and discusses the role of computer simulation in planning problems. It briefly describes a simulation model which has been developed and previously reported12 and discusses the results of a pilot study conducted on the Tri-City area (Albany, Schenectady, and Troy, New York). 3

Jan 1, 1970

By C. H. Herty

The elimination of metalloids in the open-hearth process depends on oxidation of the metal by diffusion of FeO from the slag (or absorption of FeO by the metal), with subsequent reaction between dissolved iron oxide and the metalloids carbon, manganese, phosphoms, and silicon. During an investigation on deoxidation with silicon, data on rate of oxidation of the metal were obtained, and these combined with certain other information, are presented here in an attempt to show the fundamental principles governing the diffusion of FeO from slag to metal. Inasmuch as the aim of the investigation was not a study of diffusion, certain data are lacking and it has been necessary to make assumptions on metal viscosity and effect of temperature on diffusion. These factors are known to exert a considerable effect on diffusional processes. Overoxidation, or supersaturation of the metal with iron oxide, is not taken up in this paper. Overoxidation has little effect on diffusion except under a few special conditions, and the discussion has therefore been limited to diffusional processes. Though the results given in this paper should be regarded as preliminary, certain of the conclusions drawn are definitely applicable to any steelmaking process. Previous Study of Absorption An extensive study of absorption has been made by the Department of Chemical Engineering, Massachusetts Institute of Technology. The results are of such direct interest in the problem of slag-metal reactions that it is feIt worth while to summarize them here. The following quotations are from Lewis and hitmman.1 The reader need simply substitute "slag and metal" for "gas and liquid," with proper modifications to take into account the variations in physical properties of

Jan 1, 1929

By J. Y. Kim

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In the present study, the flotation response of silver from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (Ag, CU)2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1990

By Francisco Carvalho

Durante o comissionamento o laminador Novelis CM3 apresentou níveis elevados de vibração, que causou instabilidades no processo de laminação, gerando problema de qualidade e desperdício de produto. Devido à vibração, as chapas produzidas pelo CM3 apresentaram marcas de Chatter, e para entender esse fenômeno foram empregadas as seguintes técnicas: Análise de Vibração, Análise da Forma de Deflexão Operacional e simulação numérica pelo Método dos Elementos Finitos-MEF. De acordo com a literatura, um laminador pode apresentar três modos de Chatter: 5-20 Hz (torção); 128- 256 Hz (3a oitava) e 500-700 Hz (5a oitava). O modo de 3a oitava é mais crítico para a estrutura. Na Análise de Vibração, os espectros apresentam níveis elevados na frequência de 153 Hz, sendo que na análise por ODS identificou-se movimentos relativos nos rolos de Backup e na estrutura de apoio em 153 Hz. Os cálculos por MEF destacaram a existência de um modo natural em 153 Hz nos rolos Backup, como observado nos modos operacionais obtidos por ODS, caracterizando ressonância no sistema. Esta ressonância está associada à vibração do modo de 3a oitava, que ocasiona níveis elevados de vibração no sistema. A excitação deste modo natural faz com que haja a flexão dos cilindros, que causa variações na pressão de laminação gerando assim marcas nas chapas. Também, realizou-se uma Análise Modal do rolo Backup identificando-se uma frequência natural na região de 150 Hz, com a forma modal de flexão.

Aug 16, 2017

The leaching characteristics of a number of Australian uranium ores were determined under acid and alkaline conditions. Ores from the Ranger, Nabarlek and Koongarra deposits in the Northern Territory were readily leached in dilute sulphuric acid. Suitable processing conditions were: leaching at 35-40°C, pH 1·52·0 and redox potential -475 mV for periods of 16-24h with ore ground to 50 per cent -200 mesh CB.S.S.). Ore from the Roxby Downs deposit in South Australia required leaching at 55°C and a redox potential of -650 mV to achieve a satisfactory recovery. All ores contained refractory minerals which were not leached under conventional conditions, limiting uranium extraction to 86-96 per cent.Carbonate leaching of carnotite in calcrete ores from Yeelirrie and Lake Way in Western Australia yielded uranium extractions of at least 98 per cent. Leaching rates were considerably faster than those reported for other applications of alkaline leaching as the slow oxidation step was not required.

Jan 1, 1979

By Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the Twin Cities Mining Research Center. This Bureau of Mines paper describes the simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of multiple location systems. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1974

By K. Iwami, K. Abe

"Onahama Smelter and Refinery has been operated-since 1965 arid currently produces 243,000 metric tons per year of cathode copper. The Onahama tankhouse consists of conventional-type No.1 and 2 tankhouses with the capacity of 123,000 metric tons per year and No.3 tankhouse with 120,000 metric tons per year, adopting jumbo tank system, using hazelett anode respectively.In October, 1996, for the purpose of improving the - anode verticality, new anode copper body press machine has been installed in No.1, 2 tankhouses; by increasing Walker type anode copper weight by 35kg to 365kg. Consequently, it is possible to raise current density from 191 to 222 A/m2 and the No.1 and 2 tankhouses capacity was increased by 15,000 metric tons per year to 138,000 metric tons per year.At present, the refining capacity is 258,000 metric tons per year in total including No.3 tankhouse.This figure is the largest one in Japan.IntroductionSince the Onaham tankhouse was put into operation in 1965, the cathode copper production has increase with much labor cost saving.The following two cases to increase Walker type anode copper weight by 35kg to 365kg were studied.a) To increase the cathode copper production by raising current density.b) To save the labor cost by prolonging the anode cycle in order to decrease the exchanging time of electrodes.So the electrolytic tests were carried out to confirm· the effect of current efficiency, cathode copper quality and working conditions for space adjustment.As a result, we concluded that it was indispensable to introduce the anode body press machine to keep usual current efficiency and cathode copper quality with same workers, and to be possible to increase cathode copper production.In addition, the high-speed press machine was needed to maintain same working time and which specifications were decided through various investigations. In October 1996, the new anode body press machine made by Kawazoe Machine Works, Ltd. has been installed in No.1 tankhouse."

Jan 1, 2000

By Scott M. Doehla

A proposed rehabilitation of a 200,000 sf, 75-foot high steel-frame building at the former U.S. Navy Yard in Brooklyn, New York required the review of existing foundation data and an investigation of the foundations with respect to their condition. The building was constructed in stages between 1856 and 1933, including several expansions and interior equipment with isolated foundations. The building has clear spans on the order of 50 feet and at one time supported cranes allowing transport of heavy equipment through the building. The proposed rehabilitation is to include a food manufacturing center and office space having multiple stories. Original construction drawings, available from the Brooklyn Navy Yard Development Corporation?s drawing archive, were reviewed to determine the foundation system supporting the structure. The original drawings provide a window into the methods utilized during late 19th and early 20th century pile foundation construction. The review revealed that the building is supported by pile foundations ranging from timber to concrete-filled steel pipe (depending on the year of construction). Annotations including pile driving records were available on some drawings indicating the design and as-built capacity (using the ENR formula for driving resistance). An investigation consisting of test borings was performed to identify the subsurface conditions underlying the building for evaluating theoretical capacity of the piles. A test pit investigation was performed against existing columns within the structure to expose the piles and pile caps for inspection pertaining to pile condition. The test pit investigation revealed methods utilized during original construction to integrate new columns with existing floor slabs, the use of below-grade brick arches to support a floor slab, and the condition of timber piles which were likely installed up to 120 years ago. The observations made within the test pits were compared with original drawings to evaluate the accuracy of these drawings.

Jan 1, 2008

By Fabiano Mendes

Processos industriais de carbonização são tecnologias maduras e operam há mais de 7 décadas. Contudo, o sistema integrado de produção de ferro primário e aços a base de biomassa como fonte de energia e termorredutor, mesmo sendo a alternativa ambiental de menor impacto existente, chega a seus limites tecnológicos, ambiental e econômico, ameaçando a sua sustentabilidade. O grupo Vallourec buscou o processo Lambiotte como base tecnológica para desenvolver seu ambicioso projeto de carbonização contínua, em substituição ao processo artesanal de fornos retangulares de batelada, utilizados atualmente. O esforço experimental de mais de meia década, com a adaptação e profunda reengenharia do processo Lambiotte, que é o que melhor representa esta classe de reatores, para que ele atendesse as condições brasileiras e o uso das espécies de madeira da família dos Eucaliptos culminou no desenvolvimento do processo de carbonização continua Carboval, que demonstrou sua plena capacidade, para atender aspectos econômicos, sustentáveis e de qualidade siderúrgica do carvão vegetal produzido.

Aug 17, 2017

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

It's long been suspected that there has been an increase in the incidence of premature failure of rock bolts in underground coal mines over the past ten years. As far back as 2002 a study found a possible contributor to such premature failure in some Australian coal mines might be linked to stress corrosion cracking (SCC) (Crosky et al, 2002). That study suggested the low impact toughness could be a major influence on the susceptibility to SCC of different steel compositions. A subsequent study involving laboratory corrosion tests however failed to confirm any link with metallurgical factors (Villalba and Atrens, 2007), a finding that is at odds with field experience. Some mine sites today are still reporting prematurely failed rock bolts to the rock bolt manufacturers; the failures are being identified at SCC induced. To this end a research project has recently been commissioned at University of New South Wales (UNSW), which aims to identify the environmental factors causing SCC, through field test sites and simulating the conditions within an accelerated corrosion laboratory. This paper outlines the methodology that will be used in this study.

Nov 25, 2010

TIMBER supports for large underground cavities are temporary expedients until the permanent filling can be put in. Nevertheless, timber supports are very necessary in some form. The general problem is to support the cavity in all directions withthe minimum of timber, disposed in the strongest way. The simplest way of filling an irregular space with timber sets is to form triangles.The right-angled isosceles triangle (Fig. 1) leads to the true square set, in which caps are equal to struts. The right-angled unequal-sided triangle and the scalene isosceles triangle (Fig. 2) lead to the oblong square set, where caps are longer than struts.The scalene triangle (Fig. 4) leads to the rhombic or oblique set. The equilateral triangle leads to the hexagon set (Fig. 3), in which the caps and struts are all equal. These five plane figures, the triangle, square, rectangle, rhomb and hexagon, are the only figures that will completely fill any irregular plane figure, without interstices. Hexagon sets were first suggested by the writer in 1902 to a mine manager at Broken Hill, who did not see his way to use them.

Jan 1, 1912

High flotation of iron sulfide minerals at high pH values in copper ores is mainly due to the activation of these minerals by copper species dissolved from copper sulfide minerals during grinding. Several methods have been tested to reduce this copper activation during grinding and therefore to depress iron sulfide flotation. They include grinding the minerals at high pH values or with a less reactive medium such as high chrome, and addition of a thiol collector or copper complexant during grinding. The efficacy of these methods in the flotation of a copper ore was tested against more common methods of depression of iron sulfide flotation. The mechanism of iron sulfide depression in these methods was also investigated.

Jan 1, 2014

By Robert S. Penczak

Red Lake Gold Deposits ? Descriptive Classification (modified from Pirie, 1982) VHR Au -- Volcanic-hosted (vein & wall-rock) replacement Au deposits ~93% of camp production Q-(T) Au -- Quartz-(tourmaline) vein Au deposits ~7% of camp production Quartz-sulphide Au deposits Porphyry-hosted sulphide Au deposits Current & Significant Past Producers Camp Production 21.6 M oz / 672 tonnes Au Other Deposits / Occurrences (Intermittent Exploration

Apr 1, 2005