Search Documents

By Warren L. J, Horsley R. R, Meagher L

Mineral concentrators often use process water that is very saline and/or hard. In this paper the effect of increasing concentrations of sodium chloride and calcium chloride on the rheological properties of 70 wt% quartz suspensions (d5o - 10.6 ¦m) is reported. The apparent viscosity at 100 s t in 5 mol dm -3 sodium chloride solutions (approx. 300,000 ppm) was nearly 500 times the viscosity of water without salt or particles present. Part of the increase in viscosity is caused by aggregation (coagulation) of the suspension.

Jan 1, 1989

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

By Carrie Smith

This fall, the Society for Mining, Metallurgy & Exploration (SME) will begin a new chapter by welcoming its new executive director and chief executive officer (CEO). Melissa Russell, a successful nonprofit executive with more than 30 years of experience in global association management, officially stepped into the role on Sept. 29, 2025. She succeeds longtime CEO Dave Kanagy, CAE, who is retiring in March 2026 after more than two decades of transformative leadership. “I am honored to begin this new chapter with SME and inspired by the vital role this community plays in shaping our world,” said Russell. “I look forward to listening, learning and working alongside this remarkable group of professionals to advance innovation, champion sustainability and create a brilliant future together.” Russell brings a deep portfolio of leadership experience in technical and industrial associations to SME. Most recently, she served as executive director of the Institute of Electrical and Electronics Engineers (IEEE) Computer Society, the largest of the IEEE’s 39 societies, with more than 50,000 members across 150 countries. During her tenure, she strengthened global engagement, advanced financial sustainability and launched strategic humanitarian initiatives.

Oct 1, 2025

Planning the primary development of a mineral deposit usually is done only once during the life of a mine. As a consequence, not optimizing the primary development of a mineral deposit can cause disadvantages over the whole life of a mine and can lead to higher costs. As a contribution to an improved primary development design procedure beyond the already existing work a study of the identification and quantification of the influence of parameters on primary development based on operational data from working mining operations has been completed. Based upon such a quantification of the influence of parameters a sequenced decision model was developed, that enables to develop an initial concept for the design of the accesses from the surface based upon a few critical parameters. Such a model will not replace detailed planning work within a feasibility study, but it is intended to reduce the amount of planning efforts at an early project stage through providing information what are most likely economic solutions, based on simple rules.

Jan 1, 1997

By Valentin Garfias

ALTHOUGH Mexico still ranks second in importance as produce for petroleum, the output in 1924 was 7 ½ per cent. less than in 1923 and 30 per cent. less than the peak production of 1921. The decrease may be partly accounted for by labor troubles and revolutionary activities early in the year, although undoubtedly the main factor was the continuous rise of the salt-water level in the South Fields, causing a decline of 24,000,000 bbl. in the production of light oil. Since the middle of 1923, the production of heavy crude has been greater than that of the lighter grade and, in 1924, the output of heavy crude was 2 ½ times that-of the light oil. DEVELOPMENT Drilling operations in the Mexican fields were probably more active in 1924 than in any other year, the greatest activity taking place in the Cacalilao and neighboring fields; toward the end of the year there was an added number of wells drilling in wildcat areas. The number of wells drilled in proved territory was almost twice that of the previous year, the increase taking place in the heavy-oil fields north of Panuco, as only 78 of the 710 wells completed were drilled in the Southern Fields. The percentage of successful completions decreased from 45 per cent., during 1923, to about 38 per cent., during 1924; there was also a noticeable decrease in the average flush production of the new wells. It is interesting to note that notwithstanding the increased drilling activity, the total production declined over 10,000,000 barrels. In the heavy-oil district, 632 wells were completed but only 231, or 36 ½ per cent., were commercially productive. The develop-ment in the Cacalilao area reached its peak in April and May, or about the time the first serious salt-water encroachments took place. Development in the old Panuco and Topila fields was more active than during the previous year, although the salt-water level continued to rise, the high price of crude making such development advisable especially for companies having to protect large-investments.

Jan 3, 1925

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By João Henrique de Andrade Lima

Dentre os mecanismos de desgaste existentes o desgaste por abrasão é responsável por cerca de 50% de todo o desgaste gerado. Alinhado à busca do desenvolvimento de novos mercados para o aço inoxidável, foi desenvolvida uma metodologia, para a medição da taxa de desgaste abrasivo de diferentes aços. Uma politriz foi escolhida para o ensaio devido à possibilidade de controlar a força, tipo de abrasivo, vazão de água, tempo e velocidade de rotação do disco. Para o ensaio foram preparados corpos de prova do aço P410D com dimensões de 40x40mm. Os corpos de prova foram fixados em suportes de baquelite e este conjunto foi acoplado junto à politriz. Após a escolha dos parâmetros ideais para o teste foram realizados testes comparando a taxa de desgaste de diferentes tipos de aços permitindo ranqueá-los de acordo com sua resistência ao desgaste abrasivo.

Aug 17, 2017

By Y. C. Kim, S. L. Barua

Underground coal mine planning has traditionally focused on the mine design aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most US underground coal mines. With the enactment of the Clean Air Act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the Btu content of coal are equally important for boiler efficiency. Coal mine planning must incorporate coal quality control aspects as well as traditional safety and efficiency aspects. According to an article in Coal Age (March, 1982), nearly one-half of the US coal exported to Europe does not meet the contract specifications regarding ash, sulfur and Btu contents. Although one of the reasons cited for this problem was "inadequate sampling at the US ports," the more fundamental cause probably lies in the inadequate quality control of run-of-mine (ROM) coal at the source. To perform adequate quality control of ROM coal, mines need predicted short-term in-situ coal quality information. Such predictions are generally based on whatever available sampling information is around the mine workings. Unfortunately, the closest sampling information, in the form of diamond drill hole assays, is often several thousand feet away in most underground coal mines and is inadequate for short-term coal quality prediction purposes. This is because the diamond drill holes (DDH) were traditionally placed in the coal deposit during the mine development phase to determine coal seam continuity and overlying roof conditions. They were not placed for short- term mine planning. A study was undertaken by the University of Arizona for the Homer City Owners in Pennsylvania to show that there is a need for more closely spaced samples, if the short-term coal qualities are to be predicted with any "reasonable" degree of accuracy. Prior to this study, a short-term quality prediction model, STPM, had to be developed. This model uses not only DDH, but also other sample information obtainable during face development work to predict the qualities of in-situ coal that are available in the immediate future.

Jan 1, 1985

By L. C. Lang

INTRODUCTION The introduction of 165-mm (61/z-in.) holes to underground mining operations has made possible the application of Canadian Industries Ltd's (CIL) vertical crater retreat (VCR) mining method, illustrated in the accompanying sketches. This unique and revolutionary new application of spherical charge technology (see the Appendix), when applied to primary stopes and pillar recovery, eliminates raise boring, slot cutting, and dilu¬tion of ore by backfill; greatly improves fragmentation; reduces labor and time requirements; eliminates uphole drilling and blasting; and minimizes or completely elimi¬nates damages by blasts to the walls and retreating backs of the stope or pillar. If vertical large diameter holes are drilled on a designed pattern from a cut over a stope or pillar to bottom in the back of the undercut, and spherical charges of explosives are placed within these holes at the calculated optimum distance from the back of the undercut and detonated, a vertical thickness of ore will be blasted downwards into the previously mined area. Repeating this loading and blasting procedure, min¬ing of the stope or pillar retreats in the form of horizontal slices in a vertical upwards direction until the top sill is blasted and the mining of a stope or pillar is completed. The VCR method is also applicable to drop raises and has the potential to replace all other raising methods under most circumstances. PILLAR RECOVERY Levack Mine Inco Metals Co., Ontario Div., provided the first opportunity for the method in pillar recovery. The Levack mine's high grade ore pillar No. 4800 on the 975-m (3200-ft) level was used for the production¬scale experiment (Figs. 1 to 3). The pillar was about 49 m (160 ft) long, 6 m (20 ft) wide, and 20 to 26 m (65 to 85 ft) high. The mined area on both sides of the pillar was backfilled with a 1:30 cement:sand mixture. The pillar was removed in two phases. In phase 1, the standard uphole method was used to blast down the 18-m (60-ft) long section of waste from the bottom of the ore into the undercut. From the pillar's top sill, 165-mm (61/a-in.) holes were drilled downward into the pillar, and by measuring the depth of the holes, the results of the uphole blast were determined and roof line 1 was established. The bottom of each hole was plugged, then filled with sand to place the center of gravity of each spherical charge (loaded from the top sill) at a predetermined optimum distance from the horizontal free surface. The charges were then detonated. After detonation, both draw drifts were full of extremely well-broken material. The depth of each hole was measured again, and the plot of these depths re¬sulted in roof line 2. The same blasting procedure was repeated and the resultant new back elevation was marked by roof line 3. The poor results of the initial uphole blast at one location (notice the peak in area 1) appeared to influ¬ence the subsequent new backs. A third blast success¬fully evened the back, and resulted in roof line 4. An unblasted slab averaging 6.3 m (20.9 ft) thick remained below the pillar's top elevation as the final sill. In all three spherical charge blasts fragmentation of the blasted material was extremely fine. The backfill was fully exposed on both sides of the now-blasted pillar. The backfill remained undamaged and the ore was not diluted by sand. The remnants of all the 165-mm (61/2 -in.) holes remained clean and undamaged, and the holes had well-defined bottoms that could be easily measured and plugged. Each blast took down a 3.9 to 4.2-m (13 to 14-ft) thick horizontal slab of ore. Productivity was three times greater than that of the previously practiced cut-and-fill method. Since this was the first such experiment, blasting the remaining 6-m (20-ft) thick final slab was the sub¬ject of some deliberation. If the described method was repeated, we could have ended up with a 1.8-m (6-ft) thick sill unsafe to work on. It was therefore decided to blast the whole sill using two spherical charges prop¬erly placed in each hole, but with the application of

Jan 1, 1982

By J. M. Hollow, D. E. Walsh, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Carbon fines are collected by a filter press because of their gold value. Samples of the carbon fines show that they consist of 20-30% carbon, 70-80% grit and 0.17-0.68 kg/t (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in a form of recrystallized free gold grains, with the balance being adsorbed gold on the carbon. High recoveries of gold and carbon were obtained in laboratory tests using froth flotation, with a high rejection of the grit.

Jan 1, 2001

By Jairo Romero, Fernando Pajuelo

Este estudio propone un Secuenciamiento de estrategias operacionales con el fin de reducir la dilución, el método de taladros largos en vetas angostas necesita desarrollos de secciones amplias para equipos mecanizados, esto causaría una alta dilución con este tipo de sección para vetas menores al ancho de desarrollo. Los resultados permitieron una disminución del factor de potencia (kg/tn) de un 25%, la dilución pasó del 40% hasta 8% mediante técnicas de cargas desacoplada en el proceso de voladura. Y una reducción del costo operacional de hasta un 31% menos.

Sep 30, 2022

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat, area of northeastern Colorado. Sample 31310 was taken from the Continental Oi1 Co.'s well Briggs No. 1 which came in on September 27,7.931, with a maximum production of 940 barrels per day. Sample 31311 was taken from the Reiter-Foster Oil Co.'s well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day. These two samples of crude oil are typical "intermediate base" crude oils according to the classification defined by Smith and Lane. The characteristics of these two samples, as shown by the Hempel analyses, indicate that they are almost identical. They have a very low sulphur content, and the residuum has a low carbon-residue content which would indicate that they are excellent crude oils for refining. Crude oils yielding a residuum which has a carbon-residue content of 4 per cent or less usually make good material for the manufacture of cylinder stocks. The pour points of the samples and the cloud test of the fractions obtained from the vacuum distillation indicate that the Greasewood Flat oil contains considerable wax. The high wax content would cause some difficulty in transmitting this oil through a pipe fine during extreme cold weather.

Jan 1, 1932

Current models for the origin of banded iron-formation (BIF) derived in situ iron ore deposits assume that the typical chert and iron oxide banded BIF is the primary rock from which enriched iron ore deposits arise by the selective leaching of quartz and the residual accumulation of the iron oxides. Weathering extends to the base of all the hematite deposits of the Hamersley Province, which lie within the saprolitic weathering zone, as shown by the preservation of the primary textures, and are overlain by a hydrated goethite zone representing the solum. Since groundwater typically contains dissolved silica, derived from the hydrolysis of silicate minerals, greatly in excess of the saturation solubility of quartz, it is incapable of removing quartz from below the watertable, and quartz is preserved in all saprolites derived from quartz bearing rocks. Quartz may be dissolved in the solum due to the influx of meteoric water having little or no dissolved silica, but soil-forming processes that dissolve quartz likewise alter the oxides by hydration and transposition with consequent destruction of primary textures, and there is no suggestion of soil-forming processes having produced the deposits, which typically extend to considerable depths below the water-table. A characteristic feature of the typical hematite orebodies is the unaltered nature of the iron oxides in the ore compared to those in the adjacent cherty BIF. Although the solubility of ferric iron at >10 ppb is much less than quartz, any process capable of dissolving the huge volume of quartz must also affect the iron oxides, but evidence of this is completely lacking in most ore deposits. Hydrothermal alteration at Koolyanobbing in the Southern Cross Province affects both cherty BIF and ore, and clearly shows equal mobilisation and recrystallisation of hematite within quartz/hematite veins and in the surrounding cherty BIF, which shows no evidence for the selective leaching of quartz. Similarly, any metamorphic process capable of removing all quartz from BIF would leave characteristic evidence in the remaining oxides. However, a hydrothermal process may account for at least portions of certain ore deposits, in which the chert bands have been replaced by carbonates at comparatively low temperatures, to produce a quartz-free magnetite/ carbonate rock that is readily upgraded to high-grade ore by supergene dissolution of the carbonates. This process is interpreted to have formed high grade ore at Mt Gibson, Koolyanobbing æAÆ Deposit and Mt Tom Price North Deposit. In addition to carbonate replaced cherty BIF at Mt Gibson in the Murchison Province, there are extensive sequences of magnetite BIF without chert bands, and this chert-free facies of BIF is interpreted as the precursor to the majority of in situ hematite ore deposits, through oxidation and weathering of magnetite and iron silicate and carbonate minerals. The world-class martite/microplaty-hematite deposits of the Hamersley Province are a special case of BIF-derived iron ore deposits that were initiated during the Proterozoic era. Evidence from overlying Wyloo Group conglomeratic horizons containing clasts of Hamersley Group BIF indicates that microplaty-hematite formed within the clasts before deposition, and that Proterozoic subaerial oxidation and weathering of uplifted Hamersley Group formations produced the microplaty-hematite in both chert-free and cherty BIF.

Jan 1, 2002

By Marcos Meyer

A pelotização é um processo de aglomeração com objetivo de agregar valor aos finos de minérios de ferro (pellet feed). A partir de 2010, a mina de Brucutu situada no Quadrilátero Ferriferro (QF) passa a ser a maior fornecedora de matéria prima para as plantas de Tubarão / Vitória-ES. O estudo avaliou a performance industrial de duas misturas com alta participação de minério de Brucutu, acima do padrão utilizado na usina de pelotização. Os minérios compostos nas misturas foram caracterizados por análise química, física, mineralógica e microestrutural. O desempenho operacional mostrou superior à mistura padrão utilizada para a produção de pelotas para redução direta, permanecendo com os parâmetros de qualidade consoantes com as especificações do produto final. O conhecimento das características geometalúrgicas destas misturas com minério de Brucutu em maior escala foi de suma importância para adequar o processo e custo das principais operações unitárias da planta envolvida (moagem e forno).

Aug 1, 2018

Esso-BHP have installed a production supervisory control system that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control.The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexibility to handle future variations in operating conditions.The system will be extended to the Halibut platform late in 1970 and to the Kirlgfish platforms during 1971.

Jan 1, 1971

Mining at Hudson Bay Mining & Smelting's (H. B. M. & S.) Snow Lake Division is now in the mature stage of the mines lives. These base metal copper-zinc mines have been operating for over 30 years. Stopes had small pillars called "crown pillars", left between them. These pillars range up to 100 meters long by 40 meters wide and 15 meters thick. H. B. M. & S. has been successful in removing these pillars through the use of cable slings, electric scoops, longhole mining and diesel LHD equipment. The different shapes and sizes of these pillars has meant that many innovative techniques have been tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined.

Jan 1, 1992

By F. Parada Torres

Xstrata Tintaya S.A. opera el yacimiento a tajo abierto y procesa el mineral en dos plantas: Planta Concentradora de Sulfuros y Planta de Lixiviación de Óxidos, donde anteriormente consideraba al mineral mixto complejo como intratable en la planta concentradora, por lo que se le destinó a ser tratado como óxido marginal en la planta de lixiviación. En este sentido, el presente texto describe el nuevo tratamiento al mineral complejo en la planta concentradora. De forma que se busca definir las variables geometalúrgicas del mineral de Chabuca Norte, optimizar los procesos metalúrgicos del mineral mixto mediante la investigación geometalúrgica, así como correlacionar el entendimiento de la geología y alteraciones del yacimiento con los procesos metalúrgicos y crear valor mediante la optimización de la tasa de tonelaje de tratamiento y el incremento del porcentaje de recuperación de cobre en el proceso.

Sep 12, 2011

Coal bursts are one of the least understood yet the most critical hazards in underground coal mines. The ground motions induced by seismic events can trigger unstable failure of coal and rock mass and degrade the surroundings of an excavation. Therefore, the characteristics of ground motions should be fully investigated for an improved burst risk management. This paper analyzes ground motion features of a longwall panel from a typical underground burst-prone coal mine in China. The results showed that most of the ground motions on roadways were hardly initiate coal bursts due to insignificant energy input to the damage. The intensity of ground motions in near-field zone were nearly 20 times higher than those in far-field zone. The strongest vibration on roadway was induced by a coal burst with energy of 28,600 kJ, which can cause ground motion of 0.77 m/s and equivalent dynamic stress of 14.69 MPa. The findings of this paper can improve the assessment of seismic risks and its management.

Jan 7, 2020

By Dogan Paktunc, Larry J. Hulbert, Robert C. Carne, D. Conrad Grégoire

Abstract -A thin layer of stratiform Ni-Zn-PGE sulfide mineralization of sedimentary-diagenetic origin was deposited during the Middle to Upper Devonian in the euxinic "Nick basin". The mineralized unit (2:3 cm thick), which seems to have been developed over the entire sedimentary basin of >80 km2, consists of pyrite, vaesite (NiSi), and sphalerite. The average grade of the mineralization is about 5.3% Ni, 0.73% Zn, ?770 ppb (PGE+Au), and up to 61 ppm Re. Anomalous Se, As, Mo, P, Ba and U are present. A minimum of 0.90 x 106 tonnes of Ni were deposited in the basin (based on a bed thickness of 3 cm) during the Devonian. The unique metal association, extensive lateral distribution, persistent metal grade, mineralogical makeup, and stratigraphic control demonstrate that this is a new deposit type and a new geological environment for Ni and PGE +Au. The sulfide layer occurs at the base of a Phosphatic Chert Member which is underlain by a distinctive marker unit consisting of concretionary limestone structures. The limestone spheroids may represent a vent-specific carbonate facies developed adjacent to faults that emanated nutrient­ rich hydrothermal discharges just prior to the main mineralizing event. The suite of elements associated with the Nick mineralization suggests that the ore-forming metals were originally bound to organic matter derived from decaying marine organisms. Discharge of hot brines bearing organic­ matter-bound metals took place along numerous conduits within basin faults that are now manifest as bitumen veins. Our syndiagenetic model proposes that these fluids were discharged laterally from the conduits into the unconsolidated bottom sediment (ooze). The introduction of this metalliferous fluid, rich in organic matter, stimulated biological activity and bacterial reduction of its contained S04 to sulfide. Hot, dense, laterally migrating hydrothermal fluid precipitated thin sulfide-rich 1arninae within bottom sediment. Published thermodynamic studies suggest that the diagnostic vaesite­ pyrite assemblage crystallized at approximately 138°C. The ?34:S values range from -14.7 o/oo to-10.0 o/oo and are up to 34 o/00 lighter than locally surrounding sulfides and age-equivalent mineralized strata elsewhere in the Selwyn Basin. The ?13:C values of calcite in the footwall of the mineralized unit ( -12 o/00 to -6 o/00) are isotopically much lighter than regional values. The lighter isotopic character is attributed to the hydrothermal discharge of fluids enriched in organic compounds. Although geochemical profiles of the lower Earn Group sediments that host the Nick mineralization reveal that these black shales are not distinctive, the unusual Ni, Zn, PGE, U, Ba, and P elemental associations and their anomalous concentrations in stream sediments can be used to explore for this deposit type.

Jan 1, 1992

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006