Search Documents

Until recently, nickel laterite projects have been largely ignored, due to their supposedly higher treatment costs compared with sulphides, and to their perceived processing difficulties. A number of laterite projects in the 1970s were abandoned because of high capital and operating costs, while others experienced severe technical difficulties. Conventional wisdom had it that laterites would not be exploited until most of the sulphide orebodies had been depleted. Why then, have Australian mining and exploration companies started a resurgence of interest in the treatment of nickel laterites? It all began with the Bulong project, which has been under study since 1987, while more recently two further projects, Murrin Murrin and Cawse, have been initiated and are being fast-tracked to take advantage of the current high nickel and cobalt prices. A further project in NSW, Syerston, has also been investigated at bench-scale, but no further development has yet been announced. All these projects have the following advantages: 1. Good location near a major mining centre and,reasonably close to power, water, roads, accommodation and a developed service industry. 2. Straightforward, low cost mining. 3. Low cost of acid or sulphur. 4. Good to very good cobalt credits. In addition, there have been significant technological developments in the design and operation of high pressure autoclaves and high rate thickeners, as well as solvent extraction and electrowinning technology. This has helped to decrease capital costs and technical risks, and has allowed the development of alternative flowsheets to the existing laterite operations (Taylor, 1996).

Jan 1, 1996

By Russell G. Hood

Rock bolting or anchoring are methods of stabilization which are not being fully utilized in California and probably in other parts of the world due to lack of understanding of the principles, or due to poor results in actual installation. The problem is greater in California because so much of the rock is either soft or badly fractured and broken. Almost any recognized type of rock bolt or anchor will perform successfully is hard, fresh rock, but the problems become many-fold when working in decomposed granites, shales, soft sandstones or other soft, highly-broken rock. There has been an enormous amount of research by manufacturers, consultants, private organizations, and governmental agencies on rock bolting. It would be impossible to discuss all the methods and philosophies of rock bolting in this paper. Therefore, with the indulgence of the experts, I will give only a very generalized coverage on rock bolting techniques. However, My main purpose is to point out some of the problems of rock bolting in soft rock.

Jan 1, 1967

By G. K. Zaharlev

With a productive output growing at an annual rate of 8%, the Soviet mining industry should emerge as the world's leader in total mineral output during the 1980's. (The Soviet Union's share in the world's total mineral output in 1973 was estimated at 22 to 23%.) According to estimates by Soviet mining experts, the mineral potential of the Soviet Union will sustain the current 8% annual growth rate in the future.

Jan 12, 1974

By Joseph E. Pogue

THAT the domestic consumption of gasoline displays a marked seasonal variation, with a low in the winter and a high in the summer, is well known. It is logical to expect that the nature of the variation has itself been undergoing a change as a result of improvement in roads, general employment of closed cars; and growth of mass haulage; but so far as I am aware the change in seasonal variation has never been investigated and measured. It is the purpose of this paper to present the method and results of such an investigation undertaken as a contribution to the technique of planning operating schedules now so prominent in connection with the functioning of the industry under a Federal quota system. For the method employed I am in-debted to the suggestions and help of Frederick R. Macaulay', who kindly looked over the work sheets; and credit is due Barnabas Bryan, Jr., for assisting in the computations and the graphic work. Ideas for the approach to the problem were also derived from an article by Aryness Joy, and Woodulief Thomas of the Division of Research and Statistics of the Federal Reserve Board*-.

Jan 1, 1934

By Adriane Lopes Mougo

O efeito de escala é um fenômeno que ocorre durante o microfresamento e trata da relação entre o raio da aresta de corte, a espessura de corte e a microestrutura da peça. O aço superduplex UNS S32750 é um importante material usado na indústria petrolífera que pode ser destinado futuramente para a fabricação de microsensores e microatuadores. No entanto, ainda não existem publicações voltadas para a microusinagem deste aço, seja na análise das forças de corte, na vida útil da ferramenta ou na integridade da superfície usinada. O presente artigo trata do estudo da rugosidade de superfície e da formação de rebarbas após o microfresamento do aço superduplex, considerando diferentes níveis de velocidade de corte e de avanço da ferramenta. A análise dos resultados é realizada considerando que este aço possui microestrutura composta por grãos das fases ferrita e austenita com diferentes taxas de recuperação elástica.

Oct 30, 2017

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

Five years ago, VALE Base Metals (then INCO), approached Pelton's group at McMaster and described a challenging mineral separations problem. The McMaster group has a strong track record in colloids, polymers, and chemical additives for papermaking; however, they had no experience in mineral processing. They proposed employing hydrophobic nanoparticles to replace conventional low molecular weight, water-soluble flotation collectors. Over the last five years, Vale, together with the Ontario Government (OCE) have funded two graduate students at McMaster who have worked closely with flotation experts at Vale. Experiments involving both very clean model mineral suspensions at McMaster and complex ores at Vale, have shown that hydrophobic nanoparticles do indeed function as collectors. Key nanoparticle properties and mechanisms have been identified and the technology has been protected in patent applications. Efforts to commercialize the technology are on-going. We believe that this project is a good case study demonstrating the advantages of industry-university collaboration and the use of outside experts, who may come up with novel solutions to complex problems.

Jan 1, 2011

To secure a sustainable competitive advantage some smelters may need strategies based on flexibility in feed and product ranges depending on immediate future projections of profitability. This paper explores the technical requirements for strategic diversity in smelting, leaving procurement, marketing and contractual considerations aside. The days when a smelting operation is tied specifically to say only processing zinc concentrates are perhaps drawing to a close. While internationally traded mineral concentrates are available, attractive business opportunities must exist for fully diversified custom smelters. Certain new and emerging technologies have inherent characteristics that are evaluated in this context. The paper identifies the basic building blocks that will permit such a scenario and assesses the technical feasibility. The ability to respond flexibly to environmental pressures is highlighted as being of paramount importance.

Jan 1, 1996

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on overall grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: •Different lining profiles in rubber and steel. •Orebed magnetic lining. •Steel-cap rubber lining. Introduction Grinding mill liner life has been a subject of extensive studies. Performance of mill liners in terms of wear life and how it relates to lining material and profile is abundant in the literature. The most economical liner material and design has been selected based on "cents per ton milled". The evaluation of the effect of liner design on power and grinding media consumption which is a far more significant part of grinding costs, has been less comprehensive (Fig. 1). Lining materials Steel. The most commonly used lining material is steel, calculated on a volume basis. Steel linings have a long tradition and a number of alloys is being developed. The main families are: •High chromium white iron. •Cr and Ni white iron (NiHard). •High chromium martensitic steel. •High carbon Cr-Mo perlitic steel. •High carbon Cr-Mor martensitic steel. •Manganese austenitic steel. Steel linings can be successfully used in most applications. Rubber. Rubber linings were introduced 25-30 years ago and are today commonly accepted to be the most economical linings for secondary and regrind applications. Rubber linings offer long service life in these applications and generally [ ] outlast steel in wet applications, where corrosion is a factor on the steel. The cost relation between rubber and steel has changed dramatically over the years. In the past rubber was more expensive than steel, but today, the cost of rubber is close to half the cost of steel, calculated on a volume basis (Fig. 2). The present cost situation has made rubber linings an economical alternative in several primary grinding applications as well. The wear rate of rubber in primary applications is higher than the wear rate of steel, thus giving a shorter wear life. This can be compensated for by making the rubber lining thicker. The cost advantage of the rubber allows for this, but care must be taken not to jeopardize the grinding performance. Rubber, as a lining material, offers some distinct advantages over steel lining, such as: •Ease of installation and removal. •Safer to handle, less risk of injuries. •Faster replacement. •Reduces noise.

Jan 1, 1996

In this work, the crystallization of Carnallite from waste brine of Qaidam Basin in Qinghai province was studied based on NaCl-KCl-MgCl2-H2O phase diagram. According to this study, a new crystallization pathway to recycling waste brine was developed. The carnallite salt was formed by using this technology during the waste brine evaporation. The experiment data shows that 5 tons of waste brine was required to form one ton of the carnallite. The average grade of carnallite prepared by using this procedure was about 19.40% of KCl, 16.92% of NaCl, 28.80% of MgCl2, and 0.82% of CaSO4. This study provides an opportunity to utilization of the waste brine.

Jan 1, 2012

By Karin Batallanos, Antonio Bravo, Ely Loayza, Rafael Carpio

Este documento técnico ha sido desarrollado a partir de una perspectiva empresarial orientada hacia la optimización de los recursos y activos con el objetivo de aumentar la rentabilidad del negocio. Para lograr este propósito fue crucial la apertura y sinergia entre todo el equipo involucrado ya que su interacción conjunta desempeña un papel crucial en la consecución de nuestros objetivos.

Sep 29, 2023

By D S. Clarke, K B. Sporli

The Thames Goldfi.eld has been a major gold resource in the west of the Coromandel Peninsula, New Zealand, with the Waiotahi quartz vein system forming a large part of the field. Mineralisation is hosted by hydrothermally altered Miocene andesitic volcanic rocks. Both massive columnar-jointed and fragmental volcanic rocks are present. The vein system is dominated by the steeply dipping NE striking Waiotahi-Cambria vein, and associated splays. Hydrothermal alteration increases in intensity from isolated blocks of propylitic altered andesitic material, into the intensely clay altered equivalent. Low rank propylitic alteration is typified by chlorite, calcite and pyrite, with local illite or epidote. Clay alteration is characterised by illite, quartz, kaolinite and pyrite. While broadly forming halos around veining, intense clay alteration also occurs in strongly jointed portions of the hostrock.   Vein textures and the intense illitic clay alteration at Thames are similar to those in some of the other epithermal gold deposits of the Coromandel Volcanic zone, and in deposits of the Philippines, all related to andesitic terranes. Possible causes for textures and alteration being different in these deposits from the more classic Quartz-Adularia-Illite type epithermal systems may be that cooling/mixing rather than boiling dominates fluid evolution. Kaolinite may be also be a product of either of these different fluid types, or has resulted from overprinting of an illitic assemblage by downward percolation of acidic fluid.

Jan 1, 1991

By G. T. Vandel

Dado el alza de precios en los metales, y la baja del "mining out", se busca una permanente mejora del método de beneficio aplicados a los minerales, a través del uso de la microscopia, como sistema alternativo y actual. Por tal motivo, el propósito del presente estudio refiere un panorama de los análisis microscópicos usados como rutina, así como de otros métodos empleados para llevar a cabo los estudios especiales. Siendo las investigaciones microscópicas de minerales y de los productos de la concentración, las que se constituyen como uno de los medios más disponibles para llegar a este perfeccionamiento, además de servir en los controles de rutina de algunos procesos usuales. En consecuenca, el uso de la microscopía permite ahorrar tiempo en las investigaciones de los minerales en plantas pilotos y reduce los problemas de dichos beneficios, presentados a las minas y concentradoras de la Cerro de Pasco Corporation.

Jul 20, 1956

By E. Stamboliadis

Gravity separation techniques were used in the early years to extract native metal nuggets and flakes from placer gold deposits. This was relatively easy for visible metal grains. As the size of the grain becomes smaller traditional gravity separation techniques become inadequate to recover native gold. Cyanidation was invented as a solution to the problem. According to it, gold and other precious metals are dissolved in water by sodium cyanide. The result was a drastic increase of world gold production but at the same time environmental issues were raised. In Greece gold mining has become equivalent with the absolute destruction of the environment and is under extinction. In the last years a new type of gravity equipment have been produced which create a gravitational field up to 200 G and can separate gold from gangue minerals at sizes below 50 µm. The strong gravitational field is created by centrifugal forces and the separation occurs in a fluidized bed, formed by water flow. Accumulations of finely disseminated native gold are found in the sedimentary sequence of the Flysch of the Ionian Zone. The main gold minerals are gold and electrum present as free metal flakes and micro nuggets in the size range between 5-250 µm. Test work, using the Falcon SB40 centrifugal concentrator, at the Department of Mineral Resources Engineering at the Technical University of Crete, has shown that this particular type of gold ore can be processed by gravitational methods that require no reagents and are environmentally safe.

Jan 1, 2003

By C J. McKenzie, D F. S Natusch

The lignite deposits of Southland and Central Otago are a potentially significant energy resource for New Zealand. Current estimates put the technically mineable lignite reserves at 5.3 billion tonnes, which is more than ten times the energy content of the Maui gas field. Thus, the strategic importance of the lignite as a basis for maintaining current levels of self-sufficiency in transport fuels, or as a possible feedstock for electricity generation, deserves full investigation. The full extent of the lignite deposits was only recently established as the result of a scout drilling programme undertaken between 1976 and 1979 by the Mines Division of the Ministry of Energy, and from companion studies conducted by the New Zealand Geological Survey. These discoveries of large quantities of lignite coupled, at the time, with rising oil prices, raised the prospect of their development for production of transport fuels.

Jan 1, 1983

By Evan Thomas

It has been shown before that liquids can slip at a solid boundary, which prompted the idea that parallel-surface bearings can be obtained by the use of alternating slip and non-slip regions in the direction of fluid flow. The amount of slip at the wall depends upon the surface tension at the liquid - solid interface, which in turn depends on the chemical composition of the surface and its roughness. In the present study a heterogeneous surface was created by coating half of a circular glass disc with a coating repellent to glycerol. A rotating glass disc was placed at a known distance above the coated stationary surface and the gap was filled with glycerol. With the top surface moving in the direction of slip to non-slip region, a pressure build up can be theoretically predicted. The pressure gradient in the two regions is constant, similar to that in a Rayleigh step bearing, with the maximum pressure at the boundary. In order to accurately measure the force generated by the pressure increase, a load cell was attached to the heterogeneous disc. Experiments were conducted by varying both sliding speed and distance, and the resultant load carrying capacity was measured and compared with theoretical calculations. This allowed the slip coefficient of the coated surface to be evaluated.

Jul 31, 2018

By J. Pang, S. Chander, A. Briceno

The mechanism of sulfur oxidation in pyrite is a function of the rate and driving force for oxidation. New evidence is presented to show that, at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Pyrite is hydrophilic under these conditions. In the presence of iron-chelating agents or iron sequestering ions, an iron layer might not form. Under these conditions, the sulfur layer is exposed, and the pyrite might become hydrophobic. Stronger oxidizing conditions decompose the sulfur layer, thereby making the surface hydrophilic.

Jan 1, 1994

By P. C. Schutte, J. R. Smith

The objective of ergonomics is to enhance the effectiveness and efficiency with which human tasks are carried out. Furthermore, the objective is to improve desirable human values. This can be achieved by enhancing safety, reducing fatigue and stress, increasing comfort, increasing job satisfaction, having greater user acceptance and thereby improving the quality of life. Mechanization has influenced the prevalence of injury, mainly due to the application of human physical effort as the power source. With mechanization, the operator’s function is now essentially one of control rather than being an energy source, however the risk of injury has not diminished. Mechanization in itself has introduced inefficiencies, health risks and physiological stress. The major objectives of ergonomics are discussed through examples of acceptable and less successful implementation of ergonomics within mechanized mining. The influence of the machine system on the human is addressed and practical solutions to improve and optimize the interaction of the human and the machine are outlined. Furthermore, practical examples of control and display integration, anthropometric and biomechanic influences on design, orientation, posture and stereotypes are used to accentuate the advantages of the application of sound ergonomics principles to the specialised area of mechanized mining.

Sep 1, 2001

The foundation of our industrial welfare lies in the success of our primary industries, and, so far as mining is concerned, it is hoped that for many years it will be a most important primary industry in Western Australia.

Jan 1, 1927