Search Documents

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By Ann M. Hagni

The mineralogical, chemical, microtextural, and particle size character of electric arc furnace (EAF) dusts are being studied by reflected light microscopy, scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) and electron probe microanalysis (EPMA). The dusts consist predominantly of metallic iron, iron oxide, and calcium-iron-manganese silicate phases, together with smaller amounts of iron-manganese-zinc-calcium, iron-calcium-zinc-manganese, and calcium-iron-manganese silicates. The samples vary in their zinc contents. Chlorine occurs in phases containing iron, lead, zinc, manganese, and calcium. The dust particles range greatly in size from 1 to more than 300 ~m, but most particles are about 1 to 6 ~m. Larger particles. about 20-50 um across. also are present. They are predominantly spherical in shape, but some are cenospheres, and others are more angular particles, some of which are broken spheres and cenospheres. Their internal microtextures exhibit evidence of liquid immiscibility, exsolution, skeletal crystal growth, and oxidation react i on rims. Because EAF dusts have been classified by EPA as hazardous wastes, there is heightened interest in the treatment of these dusts to render them non-hazardous. The mineralogy of products of pyrometallurgical treatment of EAF dusts by flash furnace and pyrohydrolysis are currently under study.

Jan 1, 1991

By Jamal Rostami, Levent Ozdemir, Amund Bruland, Filip Dahl

Cerchar Abrasivity Index (CAI) is one of the commonly used tests to evaluate rock abrasiveness for cutter life/cost estimations of TBM projects. There are at least 3 style machines, 2 different pin hardness, and the test could be run on fresh rock surface VS a sawn surface. Each of these parameters has a meaningful effect on the results, but its impacts were not fully understood nor its implications well explored. This paper reviews the current practice of Cerchar testing and its implications on geotechnical investigations related to TBM tunnels and provide a set of guidelines on testing and reporting of the test results for future projects.

Jan 1, 2005

By Leszek Blacha

Since several years aog there is noted an increasing importance of the metallurgical vacuum technologies. This refers mainly to the extra furnace steel treatment processes, melting of steel and special alloys in the induction and arc vacuum furnaces, as well as refining processes of nonferrous metals. In the presented work, there is discussed a phenomenon of evaporation of volatile components of metal bath under reduced pressure with description of kinetics of this process. In this article are presented are the evaluation of the mass transfer coefficients in the melt and gaseous phase. Based on results of our own research on removal rate of impurities from liquid copper (bismuth, lead) in vacuum refining process, it is determined the thickness of hypothetical boundary layer in the gas phase. This allowed to formulate a general kinetic equation defining the evaporation rate of gaseous components from metal bath. The values of mass transfer coefficients determined from this equation were compared with experimental results by other authors working on the evaporation effect of melt components of metal alloys.

Jan 1, 2006

By Erik C. Nygaard

ANFO is the most used industrial blasting agent in the world, and is often used as a reference for comparison of other explosives. It is known to work very well under dry conditions in large borehole diameters, whilst in small bore hole diameters the formation of high amounts of toxic fumes (CO, NO and NOz) can result. In underground blasting, problems can also occur with reduced visibility caused by uncombusted ammonium nitrate.

Jan 1, 1999

By John R. Bartels

This U.S. Bureau of Mines report describes the development, system by system evaluation, and preliminary surface testing of a flywheel-powered shuttle car (FPSC). The use of a self-contained flywheel-power source has the potential to eliminate the numerous safety and routing problems associated with tethered mobile equipment. An alternative to conventional power cable systems was developed consisting of the world's fIrst seven-rotor stacked flywheel system capable of storing 6 kW·h of energy at 16,700 rpm. Numerous interdependent systems were necessary for successful interfacing with a conventional shuttle car. Each of these systems was evaluated and tested individually. Finally, the entire shuttle car was surface tested. The tests indicated that the flywheel energy system can function and operate a shuttle car. The economics of the system and the design of required support systems were not addressed in the project.

Jan 1, 1991

COLUMBIA SECTION STANLY A. EASTON, Chairman, FREDERIC KEFFER, Vice-Chairman, L. K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON FRANK A. Ross The first meeting of the Columbia Section was held on March 24, as a part of the 1916 Northwest Mining Convention which was held under the -auspices of the Spokane Mining Men's Club assisted by the Spokane Chamber of Commerce, the technical program being in charge of the Spokane Engineering and Technical Association assisted by the local sections of the A. I. E. E., A. S. C. E., and A. I. M. E. The program of the successive sessions was carefully arranged with view to its application to mining, and in addition to the technical program there were exhibits of ores, minerals, devices, etc., of interest to the delegates, who numbered over 500. A portion of the program was also arranged with special reference to the requirements of the prospector and miner. A reception, a banquet, a complimentary luncheon, a regular daily call' of the Stock Exchange, a visit to the High Schools and to one of the substations of the Washington Water Power Company and to the Union Iron Works kept the visitors entertained, the ladies being looked after by a special committee of ladies who held open house during the entire week. Several important resolutions were passed by the Convention and one by the Columbia Section, A. 1. M. E. With Stanly A. Easton, chairman, presiding, the Columbia Section, American Institute of Mining Engineers, occupied the time between 2.00 and 5.30 p.m., March 24th, the Moorish room of the Spokane hotel being filled with members and their guests. "The Apex Law and the Mineral Surveyor" was a paper presented by F. W. Callaway and generally dis-cussed because of its local application in the Coeur d'Alenes, the conclusions being reached after expensive litigation between two of the large mining operators in that district.

Jan 6, 1916

By Sara Jane Boles

In recent years the interest in rare-earth compounds as refractory materials has exceeded the available literature on the subject. While some basic properties, such as density and melting point, of the more readily available rare-earth compounds have been reported in the literature, relatively few papers can be found that deal comprehensively and primarily with high-temperature refractory properties and applications of rare-earth oxides, carbides, sulfides, and nitrides. Therefore, this bibliography has been pre-pared for the use of the ceramic industry as a guide for locating and utilizing the scattered and frequently fragmentary information available. The term "rare earths", as applied in the literature search for this bibliography, is understood to include the following elements: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, terbium, thorium, thulium, uranium, and ytterbium. (On the periodic chart, these elements appear as numbers 57 through 60, 62 through 71, 90, and 92.) It is emphasized that many of the abstracts included are from papers in which the rare-earth compound or compounds are treated along with several other ceramic materials, are mentioned only secondarily, with primary interest placed on a more commonly used refractory material, or are used as part of a mixture of materials formed experimentally and reported on in the paper. As the better known rare-earth materials, such as the oxides of uranium, thorium, and cerium, appear more frequently in the literature, they also appear more frequently in this collection. Articles abstracted include only information on the basic properties that are of interest to the refractories investigator. References to crystal lattices and related topics are generally excluded from this publication. The temperature 1,500° C. has been set arbitrarily as the lower limit for reported data on thermal properties. However, because of the scarcity of information, some reports are included in which data are limited to those obtained at lower temperatures. Many of the articles abstracted include lists of references that will be of additional assistance in pursuing specific lines of investigation.

Jan 1, 1962

By M. J. Kahn

A new Scramble has hit the African continent. This Scramble has many drivers: the 1978 Deng Xiao Ping liberalizations in China; the 1989 collapse of the Soviet empire; the ICT revolution; the ease of global communications. The underlying dynamic is the end of the bipolar world of the Cold War and its replacement with multipolarity. According to HSBC (2011), in 2050 China will be the world?s largest economy, with India number 3 and Brazil number 7. Russia will be 15th (below its old rival, Turkey). South Africa maybe ranked 30th, yet has been invited to join the exclusive (BRIC) club. One has to ask, why? It is sad to note how low South Africa is assessed to be?currently it is around number 24 in the world; the reason for the fall is that the HSBC model includes population growth, and it is in this domain that South Africa is a loser, being constrained by the impact of HIV/AIDS on its life expectancy. The original four BRIC nations include the factory of the world (China), the garden of the world (Brazil), the gas station of the world (Russia), and the back office of the world (India). South Africa comes to the club both as jeweller of the world and as gatekeeper. China, Brazil, and Russia all have considerable expertise in mining exploration, extraction, and processing.

Jan 1, 2011

By Walter Miller

The broad picture of petroleum refining engineering during 1934 continued to show a tendency in the direction of highly specialized processing improvements, particularly in manufacture of lubricating oil. The slowing up of the trend toward higher octane products in non-premium gasoline noticed in 1933 was definitely established as a fact by 1934 development, with just a slight indication of recession. No outstanding engineering achievements can be credited to 1934 in refinery cracking, unless the completion and successful operation of the 30,000-bbl. crude capacity combination cracking and skimming unit at Texas City, Texas, and a 20,000-bbl. similar unit in the East can be listed as such. Development and improvement was largely a continuation of previous lines of endeavor. Such trend as there is shows a continnation in the direction of very large integrated skimming and cracking units. A lessening of the cost of ethyl lead, coupled with the reaching of the octane number "ceiling," kept the subject of "reforming" low-octane gasoline into high-octane products pretty well in the background. Considerable interest, however, was shown during the year in cracking and polymerizing of refinery gases into high-octane motor fuel. The commercial development and application of this activity was greater in 1934 than during any previous year. Fair yields of gasoline of satisfactory stability and high antiknock value were reported, ranging from 2 to 8 gal. per 1000 cu. ft. of fixed refinery gas, yields varying with both the nature of refinery gas treated and processing methods. Assuming economic feasibility, regarding which there is still difference of opinion, gas polymerization offers the industry a possible outlet for its gases more in keeping with its basic chemical composition and value. The increased interest of railroads and heavy-duty truck and tractor manufacturers served to focus more attention on diesel fuels. The publicity given the Union Pacific diesel train, the Burlington "Zephyr" and others operated on special diesel fuels served to revive the intimations and fears of several years ago as to the ultimate replacement of the gasoline motor by diesel engines in even the passenger car field. How-

Jan 1, 1935

By V. A. Cammarota

In this report, the effects of anode-production variables, such as aggregate coke sizes, pitch binder content, and baking cycle, were investigated. A small alumina reduction cell proved effective in evaluating anodes prepared from commercial materials and from lignite coke and pitch. Compressive strength was found to be the physical property most significantly influenced, but it did not appear to affect anode consumption. Specific carbon consumption, that is, the ratio of carbon in the anodic gas to carbon theoretically oxidized at the anode, was used as an index of anode consumption. It was found that an anode made with lignite coke and commercial pitch was very low in consumption; however, anodes made completely from lignite but by a different fabrication method showed high consumption and anode deterioration. Microscopic examination of anodes after electrolysis showed evidence of higher consumption at low current densities, and was useful in judging overall anode quality. Based on the physical properties of the anodes and their consumption during electrolysis, lignite can be a suitable material for anodes, provided the proper fabrication conditions are used.

Jan 1, 1970

The amount of coal used in the Colonies before the Revolutionary War was very small, and few records of it can be found, these all being in the Public Records Office in London. The exports and imports for the years 1768 to 1772, inclusive, are shown in Table 3, which apparently do not include the early shipments from the Virginia field. For the three years 1769 to 1771, the imports from Great Britain-their only source-totalled 17,943 tons, or an average of 5,981 tons per year. If the shipments from Richmond for the same period were available, this average would probably not exceed 6,800 tons per year. In Table 4 the shipments of coal from the James River ports for the period 1758 to 1769 are shown. A few of them are re-exports of coal brought from England, but the great majority are undoubtedly of coal produced in Virginia, and the movement was partly to West Indian ports but mainly to Atlantic ports from Baltimore to Portsmouth, N. H. (Piscataway). In Table 5 the data in Tables 3 and 4 are combined, the exports being deducted, and this summarizes all the available data on the amount of coal consumed in the Colonies before the separation from England. As has already been stated there has been a tremendous amount of work done in the Richmond field over a long period of time, many mines were opened and in some cases operated for years, and practically no accurate data remain or have been published to show what was done. There are undoubtedly manuscripts still remaining that will contribute to much of the knowledge of this field, and it is well worth the while of the proper state authorities to collect all the information that can be found anywhere, to enable the future development of these coal deposits to benefit by the record of what was done in the past. Table 22 shows all the methods of shipment from this field, and all of the data available about tonnages moved over each of them. The shipments by the Chesterfield and Clover Hill Railroads are largely duplicated in some of the other columns, but allowance has been made for this in the estimated totals. In addition to the difficulties experienced with similar data for the other states, these Virginia records have one peculiarly their own; it was the custom to allow 5 pecks to the bushel of coal at the pit and only 4 pecks at the docks or at vessel side. In most of the figures it is not stated to which point they apply, and a considerable error may exist due to this cause, although certainly it does not apply to all of them. The notes show the sources of the figures used, and while it is probable that the totals are lower than the actual amounts produced, the data given are the most complete that can now be assembled.

Jan 1, 1942

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

A. L. BLOMFIELD, ? Colorado Springs, Colo. (written discussion?).¬I congratulate the author on bringing out a paper of real service to the profession. His contention of uniform size in balls is borne out by my own experience; in coarse crushing at the Golden Cycle in 6 by 6-ft. (1.8 by 1.8-m.) ball-mills we unquestionably gain by screening out the small balls once or twice a month. The point of gaging the ball size to be used by the uniformity of screen sizing is of particular interest. The necessity of sufficient return feed from classifier to the ball-mill is sound and clearly shown. In connection with this, I wish two further points had been gone into as thoroughly: (1) The effect of the quality of classification. In general, it is true that the smaller the per cent. of undersize in the feed the more effective is the mill's work. This is true on a bucking board, in tube-mills, ball-mills, and grinding pans. Given the possibility of returning. a full-feed load to any mill, it has been my experience that the effective work in the grinder is almost proportional to the quality of the return feed. (2) Again speaking generally, the shorter the tube-mill the greater is the quantity of return feed necessary to keep it loaded. The classification thus keeps the oversize in the mill more free from finished product and thus the crushing more efficient. It is very easy to overload any long mill with too much return

Jan 4, 1919

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health's ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By R. F. Kendall

Only a limited number of mass and infrared reference spectra of high purity unsaturated hydrocarbons and oxygenates are presently available in the literature. To aid Bureau of Mines research programs requiring such references, 64 mass spectra and 70 infrared spectra were obtained and are reported. The individual compounds, acquired from commercial sources, were purified by preparatory gas chromatography. Purity determinations were made using a combination of analytical gas chromatography, microhydrogenation, and catalytic deoxygenation. These spectra will aid spectroscopists in the identification of compounds of the types reported.

Jan 1, 1966

By R. A. Marshall

Much has been written by men connected with the coal mining industry, and mining laws have been enacted for the safety of the men employed in the mines, and for the protection of property connected therewith. It seems almost impossible for anyone to select a subject that has not already been read, discussed and put into effect, especially in the coal mines of Western America. There is, however, a subject of much interest to the mining public, and to which I have given a great deal of study and consideration, and which I believe will be received by this convention, and will be given due consideration in the future in applying it to the safety of the mine,- "Efficiency in Shot Firing." Beginning with 1865, and for a period of 28 years in the state of Colorado, the annual reports of the chief inspectors show that 1159 coal miners were killed in the following manner: Five hundred eighty-two by falls of rock and coal ; 517 by gas and dust explosions; 6o by careless handling of explosives and the shooting of coal by the, individual, miner. It is my firm belief that 75 per cent of these fatal accidents might have been avoided, if a safe and proper shot firing system had been installed, at each and every mine. This may sound unreasonable, but I believe that the blasting of coal by the individual miner, and the use of black powder, squibs and fuse has, in reality, caused the death of many miners, from shock after blasting, the shooting out 'of timbers, and working in powder smoke, which fatal accidents were attributed to falls of rock or coal. These conditions led the people of Colorado, through their representatives of the General Assembly of Colorado, to enact a new coal mining law, and in 1913 this law became effective, containing twelve sections devoted to the subject of Efficiency in the System of Shot Firing. During the period 1913 to 1920, the employment of a shot firer, the use of permissible. powder, and the electric hand battery has resulted in safer mines, safer miners and safer shot firers, and I believe every coal mine in the state should employ first-class, certified shot firers, use permissible powder and fire the shots with an electric hand battery. I believe where gas generates in dangerous quantities, which is generally determined by inspection of the mine, and the daily report, the shooting in. such a mine should be done by electric battery located outside of the mine. Where permissible powder is used, I have seen the shot firer start down the mine with a belt around his waist containing one hundred caps, a safety lamp to test for gas, and an open light to ignite the fuse. Would it not be much safer for the shot firer if he used the electric hand battery? In non-gaseous mines where black powder is used, I have. seen the miners carry fuse into the mine, and shot firers have been known to partly tamp the holes, which was

Jan 1, 1921

By W. R. Ingalls

I WAS led some time ago to draft a statement of economic principles immediately affecting our national welfare from the standpoint of the engineer. It was the intention to offer this to the American Engineering Council as a resolution to be adopted, or a declaration to be made, of course after suitable con-sideration and debate. The presentation has not been . formally made, but I have been asked to let it be made to the mining engineers through the medium of MINING AND METALLURGY, the American Institute of Mining and Metallurgical Engineers being a constituent part of the Federated American Engineering Societies. I shall welcome any expressions of opinion that this statement may inspire. The statement follows: The engineers of, the United States, functioning through the American Engineering Council of the, Federated American Engineering Societies, feel it their duty to advise the American people respecting the present state of economic affairs in the nation, just as an individual engineer would his client. The people of the United States constitute a great corpora-tion, whose business affairs are analogous to those of a commercial company -multiplied many times. The engineers feel constrained to offer their opinion owing to the responsibility to do things which rests upon them. Confronted by the steady impoverishment of natural resources and the operation of the economic law of diminishing returns it devolves upon management, functioning through the engineering profession aided by scientists, to make such improvements leading to increased production and such elimination of wastes as to offset the increasing adversities of nature merely to hold our own; and to do more than offset them in order to improve the scale of living of the people. The engineers accept this responsibility, but in so doing they demand attention to their advice respecting fundamental economic matters, lest they be unduly hampered in the performance of the professional duties, which they acknowledge. The American Engineering Council therefore declares the following as the advice of engineers to the American people:

Jan 8, 1923

Book new a Book reviews Economics of the mineral industries. 4th Edition. Society of Mining Engineers (Caler No. D, Litleton, CO 80127, U.S.A.). 660 pp. Reviewer: M.A. Ford Foundry technology, by P.R. Beeley. Durban, Buterworth Scientific, 1982. R124 + GST. Reviewer: A.P. van Wyk Underground Transport Symposium. Johannesburg, The South African Institute of Mining and Metallurgy Special Publication SP 1. 300 pp. R65 (Non-Member), R55 (Member), + GST. Reviewer: C.L. Workman-navies A summary of the Project DevelopmentSymposium as presented by The Australasian Institute of Mining and Metalurgy. $A 25.00. Reviewer: D.J. van Niekerk Geology of uranium deposits. Proceedings of the CIM-SEG Uranium Symposium, September 1981, edited by T. I. I. Sibbald and W. Petruk. Quebec, The Canadian Institute of Mining and Metallurgy, Special Volume 32, 1985.268 pp. Canadian $40 members, $50 non-members (plus $3 for postage and packaging). Reviewer: M.S. Toros Crushing and grinding process handbook. Chichester (England), Wiley, 1986. £49. Reviewer: M.P. Hay O'okiep's 50th birthday The 0'okiep Copper Company Limited, situated at Nababeep s,ome 35 km from Springbok, recently celebrated its fiftieth anniversary.

Jan 1, 1987

By P. Tsang

The mechanisms and functions of yield pillar are analyzed by employing finite element method that takes time dependent and plastic failure of rock into consideration. The design criteria for different geological conditions are discussed. The results provide further evidences that yield pillar design will improve floor or roof condition, especially when the floor and/or roof strata are weaker than the coal. Based on this study, the yield pillar size is determined for one cod1 mine located in southern West Virginia.

Jan 1, 1989