Search Documents

By J. T. McCartney

Thin sections of coal have been prepared for many years either by cutting on a microtome (1,2)5 or by grinding and polishing (2,1). Specimens of most coals had to be demineralized in hydrofluoric acid and softened in caustic solutions before they could be successfully cut with a conventional microtome. Some lignites could be cut without pretreatment. Jeffrey (1) obtained sections from coals of all ranks, although long and tedious pretreatment was required for anthracite. His sections were less than 1 cm.2 in area (probably much less for high rank coals) and about 5 microns thick. Thiessen (2) also cut sections of softened coals, mostly of low rank. His sections were a few square millimeters in area and about 3 microns thick. However, Thiessen preferred ground and polished sections for detailed studies because they were larger and had not been chemically attacked by softening media. He prepared ground sections as large as 4 cm.2 in area and usually 5 to 10 microns thick. Thousands of such sections, covering complete column samples of many coal beds, were studied for a number of years (4). With the development of the electron microscope and increased interest in quantitative optical studies of coals, a need for much thinner sections arose. However, no suitable technique for preparing such sections was known until Fernández-Morán developed a diamond knife for cutting ultrathin sections of hard materials (5). Workers at the Centre d'Etudes et Recherches de Charbonnages de France applied this new tool to the cutting of coal sections and have recently described their technique to the Burg, of Mines. Using their methods, with some modifications, researchers of the Bureau of Mines have succeeded in cutting ultrathin sections of coals ranging in rank from lignite to

Jan 1, 1961

By K. P. Anderko

INVESTIGATIONS of the constitution of the system Mg-Ba were first made by Grube and Dietrich1 between 0 and 47 atomic pct Ba and then by Klemm and Dincke1acker" ver the whole composition range. Klemm and Dinckelacker corroborated intermediate phases of the approximate formulas Mg9Ba and Mg4Ba, and showed a third compound to have the formula Mg2Ba, rather than Mg5Ba, as suggested by Grube and Dietrich. Mg2Ba had been previously recognized by Hellner and Laves3 s a MgZn2 (C14) type structure. The main discrepancies between the results of Grube and Dietrich and those of Klemm and Dinckelacker exist, however, in the liquidus temperatures and solidification equilibria of alloys containing more than about 10 atomic pct Ba. The liquidus temperatures measured by Grube and Dietrich, and the outline of the liquidus of Klemm and Dinckelacker are plotted in Fig. 1 on an enlarged scale. Although there are strong reasons to prefer the results of Klemm and Dinckelacker, it was considered worthwhile to remeasure liquidus temperatures of some alloys in the controversial composition range. The alloys, made up from sublimed magnesium and 99.5 wt pct pure barium, were melted in an Armco-iron crucible in a dynamic argon atmosphere. Thermal analyses were taken using a Speedomax auto- matic recorder. Careful stirring during the solidification process was required in order to avoid segregation. After thermal analysis some of the cast alloys were chemically analyzed. The intended and analyzed compositions of the ten alloys prepared are listed in Table I. Since standard barium determinations cannot differentiate between barium present as element and as oxide, both the barium and magnesium contents of the alloys were analyzed. The fact that the sum of barium and magnesium was close to 100 pct in each case was taken as evidence that no excessive oxidation had occurred. The liquidus temperatures measured are listed in Table I and plotted in Fig. 1. As can be seen, they are in good agreement with the liquidus found by Klemm and Dinckelacker. This leaves no doubt that the thermal results of Grube and Dietrich above 10 atomic pct Ba are incorrect. This work was performed under the sponsorship of the Pitman-Dunn Laboratories of Frankford Arsenal, Philadelphia, Contract No. DA-11-022-ORD-1975. Sponsorship and permission to publish by this organization are gratefully acknowledged.

Jan 1, 1958

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1989

By P. Chris Pistorius

"Ilmenite smelting involves partial reduction of iron oxide from a slag consisting mainly of T1O2, T12O3 and FeO, yielding as products iron (with approximately 2% carbon) and titanium slag. Slag purity requirements preclude any fluxing additions, and the aggressive nature of the slag necessitates a furnace freeze lining. Large departures from thermal and chemical equilibrium hold in the smelter, with possible implications for process stability. The slag is approximately 150K. hotter than the metal, which means that the metal temperature is below the slag melting point; this difference in temperature has been shown to lead to formation of a solid TisOs-rich layer between the slag and metal. Recent equilibrium measurements have confirmed that the slag and metal are not in chemical equilibrium either, with significantly more reducing conditions in the metal than in the slag. After solidification, the pseudobrookite slag structure is metastable below approximately 1400K, and may transform upon slight oxidation.IntroductionThe natural mineral ilmenite is the main source of titanium, which is mainly used to produce Ti02-based pigments. Ilmenite has the ideal formula FeTiC>3, but natural minerals can be partially oxidized (to contain some Fe3+), and typically contain MnO and MgO as well, together with associated silicate minerals. Smelting is one of the methods to upgrade ilmenite for subsequent T1O2 pigment production; smelting involves partial reduction of FeO to form metallic iron as a byproduct and titanium slag as the main product. Reduction is typically controlled to yield a slag which contains around 10% FeO, 85% (Ti02+Tij03) and 5% impurity oxides (mainly MnO, AI2O3 and S1O2). An example of a typical average slag composition from reduction of South African ilmenite is shown in Table I. As this indicates, a significant side reaction is reduction of some T1O2 to T12O3. The relative extents of reduction of FeO to Fe and of Ti02 to T12O3 are such that the slag stoichiometry is close to that of the pseudobrookite phase [1]. Pseudobrookite has the structure AB2O5 (where ""A"" and ""B"" are different cation sites); the phase which makes up the bulk of solidified titanium slag has the AB2O5 structure and stoichiometry [2], and can be viewed as a solid solution of FeTi20s, T13O5, ÌçÔÀ2è5, MgTi20s, AI2T1O5 and C^TiOs [1]. This solid-solution phase is referred to as ""pseudobrookite"" or ""M3O5"" in this paper."

Jan 1, 2012

By M. G. Ayat, B. C. Scott

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling, and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent on the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1987

By C. L. Schneider, R. P. King

The ability to predict the liberation spectra that will be produced by a closed-continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population-balance-model equation. The latest, and certainly most significant, advance made in this area is the solution proposed by King (1990), which requires one textural parameter measured directly from the ore being studied. The main advantage of King's solution is that, unlike the conventional solutions, it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Mika diagram (Andrews and Mika, 1975), which has never been measured for any ore. The characterization of the internal structure if the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize-monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one- dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1995

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inor-ganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of furnaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the produc-ing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the struc-ture. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate.

Jan 1, 1937

By Fernando de Oliveira Durão

A complete computer package for the steady-state simulation, either in analysis or in design mode, of mineral processing flowsheets is described. The main features of the simulation package are: modular architecture, flexible structure and sequential solution strategy. Different detail levels of mathematical models of several mineral processing unit operations have been developed and implemented as unit modules (FORTRAN routines). Unit operations currently modelled are: coarse/fine crushing, grinding, screening, hydrocyclone classification, gravity separation, heavy media separation, froth flotation, high gradient magnetic separation and solid-liquid separation. In design mode, a simulation study is stated as a general non linear optimization problem. The objective function is a weighted sum of square deviations between the design specification set points and the calculated values, subject to non linear equality and inequality constraints. The optimization problem solution is obtained solving successive Quadratic Programming subproblems followed by inexact line search of an exact penalty function (Powell algorithm). One non trivial example is discussed, illustrating the design capabilities of the simulation package.

Jan 1, 1992

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.'-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

By F. R. Corwin, M. S. King, R. W. Zimmerman

A model has been developed to relate the velocities of seismic waves in unconsolidated permafrost to the porosity and the extent of freezing. The permafrost is idealized as an assemblage of spherical quartz grains imbedded in a matrix which itself is composed of spherical water inclusions in ice. The theory of Kuster and Toksöaz, based on wave-scattering considerations, is used to determine the effective elastic moduli, and hence the wave speeds. The model predicts Vp and Vs to be decreasing functions of both the porosity and the water/ice ratio, and Vp/Vs to be an increasing function of these two parameters. The theory has been applied to laboratory measurements of shear and compressional wave velocities in thirty-three permafrost samples from different sites in the North American Arctic. Although no direct measurements were made of the extents of freezing in these samples, the data are consistent with the predictions of the model. The theory can be used to infer the extent of freezing of the water in the pore spaces, based on knowledge of the porosity and either of the two wave speeds.

Jan 1, 1986

By William Paul Robinson

I would like to first summarize the relevant health information relating to the workers and general populations around uranium mining as a basis for understanding the hazards associated with these operations and their available remedies. This discussion will summarize the literature on Radon and its daughters, among the most toxic uranium decay products. Second, I will discuss waste handling in the uranium industry: past, present and future, discussing exploration, mining, and milling and the volumes of water and solid and gaseous wastes which are associated with these various phases of uranium operations. This paper will also include a discussion of the various past and present materials handling technologies and their responsiveness to the concern for uranium waste isolation. I will then conclude with a summary of recent modifications in the relevant standards as applied to uranium mining and milling. Joseph Wagoner, a research epidemiologist with the U.S. Public Health Service has summarized the literature on uranium mining and its health effects in his written testimony as a commissioned witness in British Columbia Royal Commission of Inquiry into Uranium Mining in January of 1980, entitled Uranium, The U.S. Experience: A Lesson in History.1 Briefly summarizinq his report, as early as 1546, miners of uranium bearing ores in Central Europe were reported to have unusually hiqh frequencies of fatal lung disease2. As early as 1879, the real nature of pulmonary disorders among these miners was first diagnosed to be malignant neoplasia or lung cancers. Of 655 miners dying between 1875 and 1912, 40% or 276 of these Central Europe miners died of lung cancer.4 By 1939, it was reported that lung cancer mortality rate for miners in these Central European mining districts was several times (9.7 per 1000) higher than that for similar populations in Vienna, Austria (0.34 per 1000). Thus, before uranium mining began in the U.S., there was a considerable body of information linking uranium mining to lung cancers. The U.S. experience can be summarized in Table 1 also from Wagoner's B.C. Testimony.1 This table shows that through 1978, 205 respiratory cancer deaths have been observed among white underground uranium miners in the

Jan 1, 1980

By J. Charles Miller

NATURAL carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended, The Farnham anticline is used as an example and cornputationa are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. INTRODUCTION Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1937

Adsorption of Starch on Kaolinite Surfaces

Sep 13, 2010

By Chris D. Veldhoen

If you ask most diamond drillers if they have ever encountered methane gas, the answer would probably be yes. This paper explores a serious methane gas explosion that the author experienced while diamond drilling at a northerly Ontario mine. It is hoped that by documenting this event, people may be alerted to the hidden danger posed by confined methane in underground workings. Methane gas tends to be a problem the deeper you get in any Canadian gold mine. Common procedure when encountering methane is to take readings at the collar of the hole and at different lengths from the source. Monitoring continues until the readings drop below 0.25 ppm. Methane is a tasteless odorless gas that is usually locked up in the seams of the rock or is a product of decaying organic material. Occasionally, the gas is released abruptly over a short period of time. Sometimes the gas can continue to vent for months or even years. In small concentrations, methane is relatively safe. In concentrations under 0.25 ppm methane gas is considered safe to work around. Concentrations over 0.25 ppm can become dangerous. During the summer of 2001, Chris Veldhoen was drilling at a gold mine in Ontario. There were three electric hydraulic diamond drills on the 39 meter level, approximately 5200 feet deep. Two Longyear LM 55 drills were about 40 feet apart and another LM 75 was about 2000 feet away. The two LM 55?s were set up to drill holes no deeper than 350 meters. All three drills had been set up on the same spot for more than a month. None of the three drills had ever encountered methane gas in the entire time they had been drilling on the level. On the day shift of July 13 2001, the driller on Chris? cross shift hit a small pocket of gas. He tested the hole and got a reading above 0.25 ppm. He proceeded to rope off the area with a ?DO NOT ENTER - METHANE GAS? sign and a rope denying access beyond the sign. On Saturday, July 14, Chris was instructed to install a Margo plug in the hole that was emitting methane gas. Methane is usually odorless, but occasionally when encountered underground, is accompanied by a rotten egg smell. As he walked to the drill, he could not smell methane gas. He proceeded to test the hole and got a reading of 0.22 ppm methane. This number was in the acceptable range for drilling, but he plugged the hole anyway.

May 1, 2004

By J Butler, N Patel, S Narendranathan, S Rastogi

The Yallourn Mine (YM) commenced mining of brown coal in the 1920s under operation by the State Electricity Commission of Victoria (SECV), prior to it becoming privatised in 1996. The present owners of the YM, Energy Australia Yallourn (EAY), acquired the site in 2000 and intend to continue operations until scheduled closure in 2028. Brown coal extracted from the YM is fed into the Yallourn Power Station which supplies approximately 22 per cent of Victoria’s electricity. Water within the YM is collected and stored in the Township Field Fire Service Pond. Water levels within the Fire Service Pond (FSP) may fluctuate considerably depending on the requirement for storage at the site. With due consideration to the stability performance of mine batters adjoining the FSP, the authors performed slope stability assessments to evaluate the risk and consequence of batter instability during the potential pond filling as it approaches the ‘critical pool’. The critical pond is defined as the level at which the driving forces (destabilising forces) are at their greatest and the resisting forces (lake forces, friction) are at their lowest. This assessment was undertaken using the Mine Geotechnical Risk Index (MGRI) approach.

Aug 2, 2023

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By B. F. Tillson

HAVING been asked to talk about recent devel-opments in mining equipment, I chose the sub-ject of small units of storage-battery locomo-tives which recently have been developed with the idea of motorizing transportation in the mines as far as possible, replacing the manual labor of hand-tramming. Metal mines are probably less advanced in this field than coal mines, where transportation of large ton-nages on any one level is quite common. Of course, metal mines, where large tonnages are handled on any one level, are as advanced as coal mines, and storage-battery locomotives for main haulages are used quite commonly in such metal mines, but the mines having levels at many intervals in the depth of the orebody, or a number of intermediate levels in which a consider-able amount of hand-tramming has to be done, and small metal mines in which the size of the orebody does not seem to warrant the initial capital expenditure for the driving of main haulage levels and installation of rock and ore chutes and raises for the delivery of the broken ore and rock to the cars have been at consider-able disadvantage in replacing manual labor by some mechanical means of transportation. Several years ago the field was canvassed among the manufacturers of electric-locomotive equipment and the conclusion was reached that the art had not been devel-oped to the advantage of metal miners who desire to replace small units of labor by locomotive equipment. The need for such small locomotives is all the more em-phasized by the development in the past few years of mechanical mucking-machines (loading equipment for filling the cars from muck piles on the level). Any me-chanical loader is a liability instead of an asset unless means are also provided for keeping the material away from the loading-machines. Therefore the transporta-tion system must be equal to the capacity of a loading-machine, otherwise the latter is idle such a large per-centage of its time as to prove an unprofitable invest-ment. So there is a need for portable, small haulage units to handle small mine cars in many metal mines, and, naturally, units are desired which can be so readily shifted from level to level as to facilitate their free use. Of course, in mines in which each level comes to the shaft it is not such a difficult problem, but many mines have a great many intermediate levels which must be approached through raises, timber slides or other small openings required to transfer ore and to get timber and other supplies to those levels.

Jan 5, 1927

Uranium minerals were found in Australia as early as 1869, but it was not until the 1940's that a search specifically for uranium was begun. Instrument types and techniques used in early exploration are still used today, but have been developed into more sophisticated and portable types. Recent improvements in exploration have been the introduction of the gamma ray spectrometer, radon sampling and geochemical surveys. The environments of presently defined uranium deposits are predominantly sedimentary. Known deposits in igneous environments are usually small. The size of targets which are likely to provide economic deposits is of the order of 10,000 tons U308, producible at a cost of less than $10 per pound. Such targets are most likely to be in Precambrian sediments or in granitic masses. Recent exploration in Australia has included investigation of Precambrian sediments, Precambrian and Palaeozoic granites, Mesozoic and Tertiary sediments, Precambrian volcanic rocks and brecciated masses of unknown age. The origin and method of emplacement of uranium in these environments is not well known but there are indications that syngenetic sedimentary processes are important, and volcanic rocks may make a major contribution to the supply of uranium.

Jan 1, 1970

By Lisheng Shao

Soil mixing and jet grouting have been widely used to support heavy structures such as tanks, cement silos, and storage buildings. Although the installation methods vary between soil mixing and jet grouting, the end product of soil-cement columns behaves similarly in supporting structure loads. In many cases, soil-cement mass treatment offers the owner savings over driven/drilled piles. This paper discusses the design methodology, production work, and quality control, with supporting figures, of a recent large complex tank farm project. The project consisted of constructing six above-ground steel storage tanks and an approximately 700-foot-long fill slope. The tank farm site is located in an industrial area of southern California, with highly variable subsurface conditions consisting of compressible soils and buried construction debris. The compressible soils necessitated that the new tanks be supported on deep foundations. A test pile program performed previously at the site showed that conventional driven concrete piles were not feasible because of buried construction debris, therefore a soilcrete system was proposed. Site design included evaluating the total and differential settlement and column group bearing capacity under both static and seismic loads. Extensive field and laboratory testing confirmed the design soil-cement strength and modulus of both the soil mixed and jet grouted soil-cement columns. The project operation and quality control programs are also included in this paper.

Jan 1, 2010