Search Documents

By D. M. Hausen

A computer program has been developed by Newmont Exploration to convert mineralogic data by XRD into rock type and ore type classifications. This method has proven useful in identifying lithology from cuttings samples, where percussion drilling was an alternative to expensive core drilling. Computer printouts of rock type and ore type identifications can be generated simultaneously with mineralogic analyses, resulting in a considerable time savings in manual calculation. XRD-computer logging was first applied to the Carlin mine in north central Nevada, and later to the Maggie Creek and Gold Quarry gold deposits, southeast of the Carlin mine. Impure Paleozoic limestones of the "lower plate" Roberts Mountain Formation and the "upper plate" transitional facies have been decarbonatized to altered siltstones and shaley units along vertical faults and permeable stratiform horizons. Advanced stages of decarbonatization were accompanied by silicification. Quantitative XRD data are initially sorted into principal rock type units (limestones, siltstones, dolostones, shales) based on major mineralogic components (calcite, quartz, dolomite, clays). On the basis of relative amounts of less major constituents, descriptive subclassifications (dolomitic limestones, dolomitic siltstones, argillaceous cherts) are made. XRD lithologic data provide assistance in correlating lithologic units, and delineating favorable replacement horizons associated with gold mineralization.

Jan 1, 1982

By E. P. Williams

"Prince Edward Island, Canada's smallest Maritime Province, is located in the southwestern part of the Gulf of St. Lawrence. The Province is more or less centrally located in the Maritimes Basin, a large intermontane basin within the Appalachian orogenic belt. The Maritimes Basin is subdivided into sub-basins and uplifts which exhibit two dominant structural trends: east and northeast. The Basin is known to be petroliferous because of the seeps, shows, oil shales and albertite found in southern New Brunswick and northern Nova Scotia and the gas and oil produced from the Stony Creek field near Moncton, New Brunswick.Permian beds are exposed on the Island, mostly along sea-cliffs. A maximum thickness of about 5,000 feet of red beds -shales, sandstones and conglomerates -make up the sequence. Over most of the Island, the Permian section is much thinner. Four key wells (Mississippian tests) and several shallower tests have been drilled. The Pennsylvanian-Mississippian section thickens rapidly off the Port Hill Uplift at the northwest, where it is less than 4,600 feet thick, and continues to thicken to about 20,000 feet in the Cumberland Basin at the southeast. Geological and geophysical data combine to give us the structural picture of the deeper beds.Prospective reservoir rocks are primarily in the Missis-sippian Horton and Windsor groups. Prospects are:-1. on or over structural highs in the basement; 2. on anticlines or fault highs; 3. over or peripheral to salt domes or salt-core anticlines; 4. at truncation pinchouts of Mississippian prospective beds; 5. in basal sandstone or granite wash on the pre-Carboni-ferous basement; and 6. in facies traps at changes from sandstone to shale or porous to tight carbonate rocks."

Jan 1, 1967

By Xiao-hui Fan, Xu-ling Chen, Xiao-xian Huang, Gui-ming Yang

Grate-kiln-cooler is a predominant process of producing iron ore pellets in China. Since this process is of multi-variant, strong coupling and large hysteresis characteristics, a reliable performance monitoring is thus essential to ensure product quality and economic benefits. Aiming to efficiently monitor the pellet induration within this process, this study proposed an approach that combines statistical analysis and quality soft-measurement. Soft-measurement of pellet quality was accomplished based on the predicted time-temperature profile, and the soft-measured indices were on-line monitored using statistical control charts. Based on the proposed approach, a monitoring system for grate-kiln-cooler thermal process was developed for a domestic pelletizing plant. Running results demonstrate that our system can assist in the detection or diagnosis of abnormal thermal state and finally helps to stabilize the pellet production.

Jan 1, 2016

For effective backfilling, a system with the 13 features covered under the section: effective backfill systems, is required. Effective backfilling cannot be done with systems that are badly designed, outdated or overextended. But in cases where the requirements for effective backfilling are overlooked, the shortcomings of such systems may wrongly come to be regarded as limitations to the capabilities of backfilling per se. Mining is currently done to depths of 3500 m, and is to go deeper since the gold-bearing reef extends down to 4000 m and 5000 m below surface. Effective backfilling systems will be required at such depths, and with suitable design this can be achieved. Mining the narrow tabular orebody of a typical South African gold mine is described at the start of this paper, then cycloned backfilling is discussed in general, and its effectiveness (most of the fill placed in South Africa is cycloned backfill or ædeslimed tailingsÆ).

Jan 1, 1998

By John J. Laffin

"IN THE BOOK that has been rated the best seller of all time, it is predicted that man will earn his livelihood by the sweat of his brow. Apparently man has accepted the statement as a challenge and has been attempting to refute it ever since, as he continues to transfer the workload to his inanimate servants - the many types of machines and other labour-saving devices that are available to assist or perform for him in the normal tasks of the day. The history of the evolution of the use of energy takes us back to primitive man, who existed in a very low energy environment, the only energy available being his own muscle power. Although man took a great leap forward when he discovered fire, which was used for lighting, heating and cooking, he still depended upon his own muscles for power. Early man's greatest achievement was probably the invention of the wheel, which permitted him to utilize the muscle power of animals. While still in a very primitive state when viewed from the perspective of the twentieth century, man, with fire and the wheel, had achieved a standard of life far exceeding that of his predecessors. Looking beyond the very basic elements of human energy, fire and the muscle power of animals, we find the next additions of energy coming from man's mastery of other elements of nature. The Phoenicians utilized the power of the wind and the Romans adapted the energy of falling water to the water wheel."

Jan 1, 1972

By G. Molloy

The purpose of this paper is to demonstrate the value of applying continuous improvement, in particular 5S and standard work, in an underground environment. 5S and standard work are two aspects of Lean manufacturing that have been applied in many industries. At Vale Canada Limited, the focus is to first stabilize the process, commonly through the use of 5S, standard work and other continuous improvement techniques. In parallel with building an engaged workforce, these approaches aim to incrementally stabilize and improve a process. 5S is an employee-driven, systematic methodology to reduce waste in all its forms through attaining, maintaining, and improving workplace organization. Identified as a foundational part of any improvement process, 5S aims to remove wastes that impact on the overall efficiency of the area. Standard work is used to formulate a common approach to how tasks are carried out to ensure consistency. Standardization involves identifying, establishing, and following the best method. The aim is to eliminate the variation that can occur when there is not a pre-defined established standard. Demonstrating the value of 5S and standard work in an underground environment will be achieved by first understanding the overall concept of Operational Excellence and continuous improvement as practiced within our operations. The paper will then cover a real application of 5S and standard work within the underground environment at Thompson, Manitoba.

Aug 1, 2013

By N. Edmonson

Apart from its role as an essential input to a wide array of agricultural chemicals and industrial processes, sulfur is interesting in that its supply involves competition between primary product and by-product. This general production structure is found repeatedly among markets for metals and other industrial minerals, and research results from the sulfur market potentially carry over to other markets with similar structures. The purpose of this paper is to present an analysis of the recent and prospective market for sulfur. The analysis will rely heavily on simulation using a comprehensive model of the North American sulfur market developed by the author. A brief description of the model is offered by way of introduction

Jan 1, 1993

By G. A. Shirey

Breakthroughs in software technology and in computer hardware capabilities have opened new opportunities to develop more accurate process simulators and to reduce the operating time to reasonable levels. As a result, there are several new simulation packages being commercialized for modeling coal preparation plants and pulverized coal-fired power plants, and the users of these packages are reporting significant improvements in process efficiency and operating costs by implementing the simulators' results. This paper provides an overview of some of the models currently in use at CQ Inc., including the ASPEN PLUS"" Coal Cleaning Simulator, the Ultramax® process optimization software package, and EPRI's Coal Quality Impact Model?. Case histories of specific applications are also presented.

Jan 1, 1995

By G. L. Alston

Rigid urethane foam can be used effectively for improving mine air conditioning systems by reducing heat and moisture transfer from mine rock to ventilating air and from mine rock to ventilation ducts, for erecting mine ventilation stoppings and overcasts, for sealings around door frames and bulkheads to prevent air leakage, for preventing spalling and sloughing of roof and rib and for erecting fire-resistant powder magazines and transformer or compression stations. Rigid urethane foam is a tough, cellular material, made by nixing diisocyanate and polyether polyol resin in accurate proportions through an applicator system, then the two chemicals react, the mixture expands thirty times its original volume with 85 to 95 percent closed cells. Within seconds, the mixture solidifies and takes a preset which will adhere to overhead or vertical surfaces. It will adhere to brattice cloth, steel, wood, concrete and rock, Excessive wetness will reduce the adherence, but in such cases adherence can be improved by preliminary application of an absorbent dust such as cement.

Jan 1, 1963

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022

By John W. Chandler

The property of the lava Cap Gold: Mining Corporation is in the Nevada City-Grass Valley mining district about 5 miles east of Crass Valley, Calif. At present (July 1940) the plant is mining end milling about 390 tons of gold-silver ore a day; about 310 men are employed. This paper describes the mining methods used and presents mining costs for 1939, when 60,704 tons were mined by cut-and-fill stoping and 55,676 tons by square-setting.

Jan 1, 1941

By James T. McCartney, Joseph D. Davis

For more than 10 years coke-oven technologists have been investigating the expanding properties of coal on a scale larger than that afforded by laboratory test tubes. Koppers 4/ was among the first to realize that coals can not be differentiated satisfactorily with respect to expansion in coke ovens by the simpler test-tube methods; in his first method 80 grains of fine coal were coked in a cylinder heated from the bottom, so that the zone of fusion (plastic layer) advanced from the bottom to the top. The scale of test was too small; it has been modified by other investigators, but without significant improvement in practical application of the results. Somewhat later Koppers and Jendne 5/ experimented with a small-scale coke even, one wall of which was movable, in which the layer-coking in a coke oven could be simulated closely. This oven was heated from both sides. Their results with this oven showed a peak in the time-pressure curves near the end of the coking, period when the two plastic layers, advancing from opposite walls, meet. They also found that although the smaller oven was heated from one side only and did not show the Pressure peak characteristic of two-sided heating, it still gave results entirely too high. Russell built an oven similar to the movable-wall oven of Koppers and Jenkner and compared results obtained in it on Beckley expanding coal with these obtained on the some coal in the Altieri 7/ small-scale apparatus. Both tests were conducted at the same constant pressure, but heating was from two sides in Russell's oven and from one side in the Altieri tester. Russell found that the two types of test gave comparable results under constant pressure conditions even though the heating procedures were quite different. He showed later, however, that a "borderline" coal 8/ that contracted in the Altieri tester at constant pressure developed a peak pressure of 4 pounds per square inch in the movable-wall oven heated from both sides at constant volume. He concluded from this that testing at constant volume gave results more accurately indicative of dangerous expansion tendencies than those at constant pressure. He also found that heating from both sides in this oven gave higher pressure than heating from one side only.

May 1, 1942

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

By I. Yochev, A. A. Metelev, A. I. Stepanenko, A. P. Purgin, M. G. Viduetsky, A. M. Panshin, I. F. Garifulin

"Pneumatic flotation cells of the KFM series are intended for the concentration of various ores and technogenic materials. The key operating principle of the flotation cells of the KFM series is the preparation of pulp for flotation in blowers, offering the advantage of an accelerated flotation process. This report summarizes the results of the implementation and operation of the KFM cells at Russian and foreign projects in 2015-2017. Their implementation and operation experience confirms the high efficiency of the KFM cells, especially in the head of lead and zinc, copper and zinc, copper flotation processes:head KFM-600 flotation cell recovers from lead-zinc ore (Rudmetal AD modular concentrator) up to 52% of lead in a single stage (without cleaner flotation) in a salable lead head concentrate (grade of up to 76% lead, 2.3% zinc). The flotation cell proved to be much more efficient than originally expected in the process description in the design phase,flotation of the copper-zinc ore from Novo-Shemur deposit (PJSC Svyatogor concentrator) in two KFM- 1400M cells recovers up to 65% of copper and 70% of zinc in a high-grade bulk copper-zinc concentrate containing 12-13% of copper and 25-28% of zinc. The installation of the two cells with a combined capacity of 26 m3 allowed to decommission 4 chambers of FPM-16 pneumomechanical flotation cells with a combined capacity of 64 m3 with a simultaneous increase in the overall ore concentration performancea single KFM-1400M cell (13 m3) recovers from the copper ore from Volkov deposit (PJSC Svyatogor concentrator) 53% of copper into a high-grade copper head concentrate (33.0% of copper). For comparison, the pneumomechanical cell FPM-16 (capacity 16 m3) has almost half as low copper recovery (29.6%) into the head concentrate at a lower grade (30.5% copper)."

Jan 1, 2018

By Frederick G. Tickell

GEOLOGISTS have been quick to adopt new methods in locating new oil fields and in finding the extensions, laterally or at depth, of the old fields. For most of these new methods he is indebted to the physicist, the engineer, and the chemist, although he has also drawn from such ordinarily unrelated sciences as bacteriology and protozoölogy. These last-named sciences have been of help in problems dealing with the origin of petroleum and, although not of direct application to oil finding, have furnished evidence of value in learning what oil is made from and what are the natural agencies involved in its formation.

Jan 1, 1932

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

################

Aug 12, 2013

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By H. Y. Sohn, M. Pérez-Tello, P. J. Smith, K. M. Riihilahti

A three-dimensional computer model for the Kennecott-Outokumpu flash converting process for copper matte is presented. The model incorporates the transport of momentum, heat and mass, and reaction kinetics between the gas and particles in a particle-laden turbulent gas jet. The k-E model is used to describe gas-phase turbulence in an Eulerian framework. The particlephase is treated from a Lagrangian viewpoint which is coupled to the gas phase through the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu2S·yFeSx. Based on experimental observation, the oxidation products were assumed to be Cu2O, CuO, Fe3O4, and SO2. A reaction mechanism involving the external mass transfer of oxygen to the particle surface and diffusion of the oxygen through the oxide layers of CuzO/Fe304 and CuO/Fe3O4 is proposed. Predictions of the mathematical model were compared with the experimental data collected in a large laboratory furnace. A reasonable agreement between the model predictions and the measurements was obtained in terms of fractional conversion of the oxidation reactions and of sulfur remaining in the reacted particles. The simulation of an industrial flash converting furnace was also performed. Higher oxidation rates, more even distribution of particles, and thus a more efficient use of the reactor volume are predicted with a burner having a distributor cone, than with a single-entry burner.

Jan 1, 1999

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989