Search Documents

By I. C. R. Gilchrist

A principal requirement in the design of a backfill transportation pipeline is the accurate prediction of the values of key slurry flow parameters. Input variables, such as particle size and solids concentration, are usually determined by the load-bearing requirements of the placed fill. It is therefore necessary to identify the optimum conditions of transport for a particular combination of input variables. This paper critically reviews the methods available to predict the values of flow parameters in slurry pipeline systems in the light of experimental data generated at a test facility. Particular reference is made to rod milled waste and deslimed tailings transport systems and, in the case of the former, it is shown that both pumping and load-bearing requirements can be optimized.

Jan 1, 1988

By Jones BH

Discovery of the Vera-Nancy deposit in late-1995 followed 12 years of active exploration in and around the Pajingo Epithermal System, an andesite hosted veinfield covering an area of 150 square kilometres at the northern end of the Devono-Carboniferous Drummond Basin in North Queensland. Early exploration targeted open-pittable resources in the numerous auriferous veins and it was not until 1994 that exploration focus shifted to drilling to depths below about 100 metres from surface, which resulted in the Vera-Nancy discovery. That deeper drilling process is still at a very early stage of coverage of the epithermal system as a whole and substantial potential exists for additional discoveries.Drill-out of Vera-Nancy has to-date established a gold resource in excess of 1.4 million ounces. Mine development is proceeding via a twin decline system with first stoped production scheduled for August 1997.

Jan 1, 1997

By B. Salopek

The greatest part of crushed stone, gravel and sand production is extracted through open pit operations, whereas gravel and sand are also partially extracted from riverbeds. Its obvious that such a mining activity provokes some changes in the configuration and environmental characteristics of the region, in the temporary or permament disapperance of vegetable or animal species and in the creation of noise, dust and waste water. However, the above-mentioned mining operations shouldn not have only negative effects on the landscape and land potential, but they can discover and predetermine the potential of the exploited areas for various communal purposes after exploitation (eg. sports and recreation centers, campsites, resorts, fish-farms, etc.). In this paper, the production of construction aggregates in plants located in the vicinity of Zagreb, the capital of Croatia is presented. The advantages and disadvantages of aggregates? production in urban areas in the spirit of sustainable development are discussed.

Jan 1, 2003

By I. N. Zavarine

AUSTENITE is often defined as a solid solution of carbon or carbide in a nonmagnetic form of iron. Conversely, magnetic measurements are often used by investigators for the purpose of detecting the degree of austenite decomposition after an iron alloy has been subjected to certain thermal or mechanical treatments. Association of the magnetic state with the gamma-phase decomposition is often extended to the alloys of iron with elements other than carbon. Definition of austenite as a nonmagnetic solid solution cannot be accepted in the light of available information without certain reservations. The relation of magnetic transformations with the gamma-phase decomposition in the complex alloys of iron has never been rigorously proved. The present investigation deals primarily with the magnetic trans-formation that occurs in carbon steels during the quenching process. The work was further limited to a study of magnetic transformation in carbon steels quenched at such rates as are necessary to retain the product of austenite decomposition in a martensitic state.

Jan 1, 1934

By A. Goldberg, T. E. Tietz, J. E. Dorn

INTRODUCTION THE concept that the flow stress for plastic deformation of metals in the work hardening range is a function of the instantaneous values of the strain, strain rate and test temperature was promulgated by Ludwick1 many years ago. This thought has been more or less a guiding principle throughout the immediate period of development and growth of mechanical metallurgy. It has been tacitly assumed or knowingly applied to many investigations on the plastic behavior of metals. Spurred by the theoretical interest and practical importance of the plastic behavior of metals, many investigators have attempted to determine empirical, semi-empirical, and theoretical equations2-18 relating the flow stress with the strain, strain rate, and temperature. Although the applications of such equations have been extensive, the experimental verification of the existence of a mechanical equation of state is weak. Furthermore, some of the available evidence on plastic flow appears to suggest that no simple functional relation between stress, strain-rate, strain and temperature can exist. The mechanical equation of state demands that [a = a(e, E, T)[I]] Where o = true stress = load/instantaneous area e = true strain = In Instantaneous gauge lengths initial gauge length e = true strain rate T = temperature] This formulation implies that [da] is an exact differential. Therefore the flow stress (o) is a function of the instantaneous values of the strain (e) the strain rate (e) and the temperature (T), independent of the previous mechanical or thermal history. Having reached a certain strain, strain rate, and temperature, by any path whatsoever, a definite and fixed value of the flow stress should be obtained. One check on the validity of the mechanical equation of state is easily obtained. Consider the following three tests on the stress-strain curve at constant temperature: [A. Strain at rate [ei] B. Strain at rate i2 C. Strain at rate [Ei] to [ei] and continue test at i2] A graphical representation of possible results of such tests are shown in Fig I. If, for strains greater than [el], test (C) data coincide exactly with the data from test (B), as shown in Fig Ia, a limited verification of the mechanical equation of state is obtained for the range of strain rates from [ii] to [e2]. But if the data from test (C) differ from those of (B) beyond strain [el] where the strain rate is changed from [e,] to [€2i] the mechanical equation of state is not

Jan 1, 1948

By Wanderson Endlich, Tarley Rezende Secchin, Ana Clara Bernabe, Jennifer Oliva Coronel, Danielle Duarte Bernardi

A ArcelorMittal Tubarão (AMT) possui desde o início de operação os recursos hídricos como uma das questões centrais na estratégia de sustentabilidade e estabilidade operacional para sua produção. A gestão hídrica na AMT, dentre outras ações, garante que 96,5% de toda a água captada na usina venha do mar. Além disso, possui investimento contínuo em reusos internos, busca de fontes alternativas de água e combate ao desperdício e vazamentos. A condução dessa gestão hídrica, contribuiu de forma significativa para atravessarmos em 2015, a pior seca que o estado do Estado do Espírito Santo atravessou nos últimos 40 anos. Todos esses esforços resultaram na redução expressiva do volume de água doce utilizado na AMT, reduzindo o consumo específico de 4,2 m³/t em 2014, para 2,5 m³/t em 2018. Como resultado de um plano robusto de gestão hídrica, um projeto arrojado e inovador, pioneiro no Brasil e primeiro do grupo no mundo será realizado na empresa, a planta de dessalinização de água do mar. Com investimentos da ordem de R$ 50 milhões, a unidade começará a ser construída em 2019, com prazo de conclusão em dois anos. Produzirá até 500 m³/h de água industrial para o sistema de água da usina, proporcionando uma importante fonte alternativa ao consumo de água doce.

Aug 1, 2019

By R. Hogg

"Agglomeration processes and agglomerate characteristics are largely controlled by the forces of interaction between particles. The nature and typical magnitude of these interaction forces are evaluated relative to the external forces commonly present in agglomeration systems. The specific roles of the interaction forces in the various stages of agglomerate formation and growth and their effects on the integrity and mechanical strength of agglomerates are briefly reviewed. Because the interaction forces affect different aspects of agglomerate development in different ways, conflicting requirements can arise. Examples of such conflicts are given and used to demonstrate the importance of evaluating the effects of interaction forces etc., in the context of the overall agglomeration process and its ultimate objectives.INTRODUCTIONThe term agglomeration is generally used to refer to processes whereby discrete particles are caused, or allowed, to associate into clumps in which the individual particles retain their identity but are held together by relatively weak, usually physical forces. Various other designations are given to these processes, depending on the specific circumstances under which agglomeration occurs. The terms balling and pelletizing are often used to describe agglomeration in dry or semi-dry powders; coagulation and flocculation are used to refer to agglomeration of particles dispersed in fluids. Common to all of these cases is the fact that the formation, growth and integrity of the agglomerates depend primarily on the forces acting on and between particles. The same forces are, of course, responsible for manyaspects of the behavior of colloidal systems and their study and evaluation constitute the,basis for colloid and interface science.FORCES ACTING ON FINE PARTICLES AND AGGLOMERATES It is convenient to classify the forces acting on and between particles into two general types: external forces and interaction forces. It should he recognized, however, that a sharp distinction is not always possible.External Forces Gravity and inertial forces act on all particles and their magnitude is proportional to particle mass, i.e. they vary with the cube of particle size. Such forces are oftensignificant for large agglomerates but may be negligible for individual, fine particles.Hydrodynamic (""drag"") forces are important, for particles suspended in fluids. For very small particles, the drag force is directly proportional to size (Stokes' Law) while for very large particles or agglomerates it varies with approximately the square of size (Newton's Law). A useful procedure for estimating drag forces over a broad range of particle sizes and physical conditions has been given by Concha (1)."

Jan 1, 1989

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By Behram H. Wadia

El presente estudio describe el proceso de volitización de plata-plomo y otros valores metálicos como cloruros en la Cerro de Pasco Corporation. La aplicación de este procedimiento busca recuperar metales como la plata y el oro, así como los metales menores: bismuto, cadmio, teluro, etc., los cuales se perciben en los humos, producto de la volatización de los valores metálicos. En este sentido, el proceso de volatilización de plata y plomo como cloruros aplicado en altas temperatura, es metalúrgicamente fac¡tible, ya que logra una eficacia de plata entre 80 y 84% y no menos de 95% de plomo. Asimismo, el uso de la cama fluidizada como reactor usado en la experimentación, es el más conveniente dado que se puede obtener mayor concentración de valores en los productos de condensación de los cloruros volatilizados.

Nov 20, 1967

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By S. H. Castro

The El Teniente molybdenite plant (Chile), with a nominal capacity of 3,200 tpd of bulk Cu-Mo concentrate, produced approximately 3,385 metric tonnes of Mo during 1998 by using the phosphate Nokes process (LR-744 reagent). This is the only Chilean moly plant which traditionally has depressed copper and iron sulfides with LR 744 reagent, which is a hydrolysis product of P2S5 and NaOH. El Teniente's ore Mo grade is 0.02%Mo and is concentrated to 0.45%-0.50% Mo in bulk Cu-Mo flotation. Subsequently, molybdenite is floated by selective flotation to depress Cu and Fe sulfides, such as chalcopyrite, bornite, digenite and pyrite, to produce typically a 49%-50%Mo molybdenite concentrate. An optimisation program during the last two years was undertaken to improve molybdenite recoveries. Current molybdenite plant technology at El Teniente and use of phosphate Nokes in the process process is reported. Use of phosphate Nokes reagent has increased average Mo recovery from 70.5% in 1977 to a mean 74.7% for the first 4 months of 1999. The global Mo recovery, including bulk flotation, incresed from 42.3% in 1997 to 46.8% in 1998, with a projection of 55.5% for 1999. Mo production per year has increased from 3,181 tons in 1997 to 3,385 tons in 1998 and a projected 4,000 tons for 1999.

Jan 1, 1999

By Andrew A. Blair

The increased importance and value of chemical analysis in connection with metallurgical operations is largely, if not entirely, due to the increased accuracy of the analytical methods used for the quantitative determination of the foreign elements always associated with the metal operated upon. This applies especially in the working of iron and steel, and to the determination of the amounts of such elements as phosphorus, carbon, and silicon. The influence of greater or smaller amounts of these elements upon the physical properties of iron and steel will be better understood when the proper experiments shall have been made upon samples whose chemical composition is known with almost absolute certainty. From the present standpoint of analytical chemistry, it is easy to see that at least one reason for the failure of many attempts to solve this problem, is the inaccuracy of the analytical methods used. Even at the present time the frequent want of agreement (over and above the unavoidable error due to manipulation) between chemists working on the same sample, leads one to think that there is still at least a choice in the methods used. It is true that very frequently a faulty method in the hands of a skilful analyst may be made to give corroborative results

The mining of Australia's rich and diverse mineral resources has been central to the development of the continent by "Europeans" over the past two hundred years. Mining has historically been encouraged (to varying degrees) by development-orientated state governments (the. managers of largely Crown-owned resources) and since Federation, by successive Com- monwealth governments (which have seen mineral development as a means of generating export revenue to fund predominantly social-welfare orien- tated budgets). This marriage of convenience between governments and the mining industry has to date served all parties well. However, Australia's entry to a new world economic environment at a time that community percep- tions are changing (owing to an education-inspired challenge to "old" values) is challenging the hitherto held assumption that mining develop- ment is always aligned with the well-being of the State and community. Issues such as the type and extent of State/Commonwealth government taxation, resource ownership and control, the environment, land use con- flict, the extent and desirability of secondary processing and infrastruc- ture funding are being debated in the public arena. Opponents of mining in the community are well-organised and are well funded, articulate and more importantly, they have effective communication channels with most governments, irrespective of political complexion. Apart from some television-orientated corporate image building and recent efforts by AMIC, the industry's response to this challenge has been unco-ordinated, poorly directed and arguably ineffective. Professionals working in the industry are concerned about the community's perception of themselves and their industry. Recognizing that the Australian democratic system ensures that, in the large, government at its various levels, is reflective of and responsive to the views and aspirations of people, the industry's response must be wide- ranging, equally articulate and couched in a form which is politically acceptable. New objectives in providing information to the public and its educators must be formulated. Moreover, professionals are looking for new directions from industry leaders. The Institute is well placed to facilitate this process.

Jan 1, 1988

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994

By Artur Frederico Fonseca da Cruz, Jael Moutinho dos Santos

The problem of iron ore sticking and premature wear on screening rolls on balling systems is recurrent. The importance of the "screening" function of the roller classifier is fundamental, since in perfect conservation state and operation it is possible to ensure the performance improvement of the most expensive phase in the pelletizing production chain, the thermal processing. The present works target is the identification of possible causes of iron ore adhesion in classifier rollers and develop a methodology to evaluate and quantify the iron ore sticking mechanism on the classifier surface. For this purpose, iron ore and additives were collected at four different pelletizing plants in terms of iron ore origins and process flows, three different rollers were chosen for testing around the adhesive energy at the iron ore mixture/rolls surface interface. As results, it was possible to construct methodologies to evaluate the aggregability, it was observed the importance of "specific moisture" definition and knowledge on the adhesive energy increase, besides presenting the better performance of rolls with tungsten carbide coating than other evaluated.

Oct 1, 2019

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By Scott D. Long

"Abstract-Grass roots exploration has an emphasis on good precision at low (sub-economic) concentrations of an element, in order to identify "anomalies" which may lead to drilling targets. Although it is wise to have well-defined quality controls in place during early stage sampling, the control procedures at this stage tend to be rudimentary. When a deposit warrants detailed delineation, the need for accurate geological characterization and assaying of ore-grade rock must be supported by appropriate quality control procedures.As a project returns more promising results, and the likelihood of the project warranting a prefeasibility study increases, it is time to tighten quality assurance requirements and quality control protocols. Delays in instituting adequate quality control and verification procedures may lead to costly remedial actions that can also delay completion of the prefeasibility or feasibility study. Sometimes, as a project matures, the quality control and quality assurance aspects fail to keep pace with the changing nature of the work: an increasing emphasis on precise and accurate assaying of oregrade rock.A resource model is like a house of cards. The foundation of the house is the geological observations, the sampling methods and the geological interpretations performed upon those samples. Upon the sampling, which includes all the sub-sampling steps of sample preparation, rest the assay results. The quality of the assays can be no better than the quality of the sampling. Good assaying technique will preserve all biases and imprecisions introduced during sampling and sample preparation; it cannot remove them. If the sub-samples and/or assays are bad and must be redone, all the succeeding levels of the house of cards must also be rebuilt, or at least patched up.From geological observations, a geological interpretation is built, the quality of which is critical to the construction of an acceptable resource model. Geological elements are difficult to assess, and are not discussed here; they are dependent upon the expertise of the geologists involved. Geological knowledge contributes essential quality control elements to resource/reserve determinations (Sinclair and Postolski, 1999; Postolski and Sinclair, 1999).This paper consists of five sections: (1) overview of quality control protocols, (2) maintaining quality control of databases, (3) quality control of drill sampling, (4) optimizing crushing and grinding requirements, and (5) quality control of assay data acquisition."

Jan 1, 1998

By D. J. Ketkar

It is a frequent experience to find that the Sub-surface Investigation (S.I.) data is either inadequate or misleading. However, such cases are rarely reported. Nonetheless, the projects suffer on-account of delays, cost-over-runs, disputes and/or compromise of the safety norms. Many times S.I. is considered unnecessary or is carried out as a ritual, mainly due to (i) non-availability of good S.I. agencies, or (ii) absence of Geotechnical consultant, or (iii) shortage of time. Importance of S.I. cannot be over emphasised. Yet the profession is in a state of confusion - mainly because of lack of competent professional agencies and of well-defined roles/responsibilities of the concerned parties. In this paper, some suggestions are made to get better returns from the S.I. activity.

Jan 1, 1996