Search Documents

By G. B. Pryde, R. M. Magraw

In laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the rise, and rooms turned at right angles to these entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut. in rooms and the back entry of the level above. All entries, rooms, and entry-and-room crosscuts should be driven .on sights and room crosscuts should be driven at, right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire. Where economic conditions permit, it is preferable to follow the retreating panel system of mining. In the case of coal that outcrops, and even in cases where no outcrop is exposed, it is preferable to commence pillar extracting on the high side of the mine. Where the retreating

Jan 1, 1922

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations wi.thin a multiple-seam configuration. At two mine sites where such ground interactions were present, the Bureau performed a complete geological analysis and installed and monitored instrumentation to gather pertinent data on rock mechanics. Overburden depth varied dramatically in the vicinity of the study area and reached a maximum at the study site; innerburden thick-ness was less than a pillar width (40 to 4S ft); heaving was experienced in both mines where sandstone and/or shale floor units were observed; overlays of the mine layouts show pillars were not totally superpositioned; a maximum of S in of roof to floor convergence was measured; and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig over instrument setting pressure.

Jan 1, 1987

By Wagner da Silva Lima

Um Sistema Piloto de alimentação de biomassa foi instalado em paralelo ao sistema de alimentação de coque em uma caldeira leito fluidizado circulante movida a coque de petróleo na Unidade Fabril da Votorantim Metais em Niquelandia, GO. Quatro experimentos foram realizados utilizando os alimentadores de coque (limitados a capacidade de mistura da pá-carregadeira) e o sistema piloto instalado que tem capacidade de 30 m3/h de cavaco de eucalipto. A substituição energética chegou a 19%, bem acima dos 10% determinados pelo fabricante utilizando o sistema atual de alimentação de combustível na caldeira. O potencial de redução de custo do vapor varia de 4 a 7%.

Aug 17, 2017

Mining is a business involving extraction of commodities of value to society from non-renewable resources. Consequently there is only one opportunity to extract ore from the ore body in order to unlock the value potential encompassed in the asset. It is therefore imperative that the maximum value is unlocked during the extraction programme, considering the relative wealth generated for shareholders and society, the sustainability of society, the environment and the operation. The bulk of the value that is unlocked is usually embedded in the initial design process. How do you measure sucess The most common measure of success is the return on investment, which is unlocked during the extraction process. This is usually only determined and locked-in during the study process. Another measure of success is the profitability that is achieved on a monthly basis. A further measure would be the enhancement the asset affords to the share price of the operation. Increasing focus on sustainable development requires that the impact on the society and environment received high priority as well. All these measures are largely encompassed in the cash flow and the discounted cash flows. This paper focuses on the dynamics of the cash flow and the most significant elements influencing return in investment. These include the mine design, production volume, sustainability, risk and valuation techniques. When do you add the most value? There are many different phases and definitions noted by different authors to demonstrate and standardise the study process for new projects. This paper is based on a process with 3 major components namely a conceptual study, a prefeasibility study and a feasibility study.

Jan 1, 2007

By G. H. Rowe, A. N. Stroh, D. P. Gregory

The magnitude and variation with strain of the parameters activation volume, V*; activation energy, H; and frequency factor, A, in the Arrhenius equation for strain rate are determined for colunlbium single crystals and polycrgstals. Comparison of dislocation structures in deformed columbium crystals as determined by transmission electron microscopy with the rate IF deformation of a metal crystal is a thermally activated process, rate theory can be used as a powerful tool in the study of dislocation mechanisms. seeger1 develops the following expression for plastic deformation governed by a single thermally-activated theory results suggests thai formation of lattice vacancies at jogs in screw dislocations is responsible for thermally activated deformation of poly crystalline columbium. Single crystals appear to deform by a different mechanism. Work hardening in fully recrystallized fine grain columbium is found to result from simultaneous decrease in activation volume and in the number of mobile dislocations with increasing strain. Work hardening in recovered polycrystals is found to result from decrease in activation volume with strain only. dislocation mechanism. His equation for strain rate is where N is the number of mobile dislocations per unit volume held up at energy barriers, v is the frequency with which the dislocations "try" the energy barriers, b is the Burgers vector, a is the area a dislocation loop sweeps out after overcoming a barrier, V* is the activation volume which will be defined more completely later, and t* is the thermal component of stress equal to (Ta-Ti), where Ta is applied shear stress and Ti is internal stress of the dislocation network17' given by

Jan 1, 1963

By Charles E. Wait

IT is said by some that the occurrence of a deposit of sulphide of antimony in Southwestern Arkansas has been known for fifteen or twenty years. Whether or not such is the case I am not prepared to say, but I am not able to find any record of such a discovery, or any analysis of antimony ore obtained from that section, published at so early a period. The present discoveries, that seem to be attracting some attention, date back to the winter of 1873-74. At that time a vein of ore was found by Mr. Robert Wolf, in honor of whom the vein was named, and still is called, "the Wolf lode." At the time of the discovery the ore was unknown to the prospector, and its composition was not thoroughly understood in that locality until samples were sent to several analytical chemists, who pronounced it sulphide of antimony-stibnite. Since the discovery of this ore there have been three mines opened, and a number of interesting minerals of the antimonial series have been found. I have had an unusually good opportunity to collect specimens from these mines; and it is owing to the constant inquiry concerning the character of these ores that I have collected for publication the results of quite a number of analyses, sufficient I trust to clearly point out their composition. This is one of the few localities in the United States where antimony ore is found in workable quantities; I say workable quantities, because two different shipments of ore have been made to English reduction works, and in both cases excellent returns were made. The discovery of these deposits will, it is hoped, give rise to a prosperous and remunerative industry at no distant day, and when fully developed they may yield ore in sufficient quantity to supply the regulus for the home demand, thus adding wealth not only to those interested, but also to the State of Arkansas. The three mines are situated in the northern part of Sevier County, and may be reached by the St. Louis, Iron Mountain and Southern Railway to Fulton, thence by wagon-road to Columbus, Nashville, Centre Point, and to the mines. During most seasons of the year the

Jan 1, 1880

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By I. R. Ward

"The need for energy conservation has been of increasing concern since the early 1970's, when the cost of petroleum based energy began to escalate rapidly and security of supply became uncertain. The cost of energy from alternative sources has also increased due to development costs and environmental restrictions.These developments have had a serious impact on the mining industry, which is energy intensive. The impact is magnified as lower grade ores are treated, and more energy is consumed per unit of product. In many cases increased operating cost is not compensated by the rise in product selling price.The magnitude of energy consumption in the mining industry is indicated by recent studies conducted in the U.S.A. and Canada. Based on 1970 figures, it was reported that the production of 1 ton of copper in the U.S.A. required 111. 8 x 106 BTU of energy, of which 60. 7 x 106 BTU (54.3%) was consumed in mining and processing (l)The survey of Canadian mills, conducted by CANMET and reported to the CMP meeting of 1978 (2), showed the following milling energy consumption figures (approximate averages):"

Jan 1, 1981

By Y. C. Liu

IN the study of the rolling recrystallization of face-centered-cubic metals, a most unusual observation is the frequent occurrence of a sharp re-crystallization texture of cube orientation. Although the general conditions under which this texture occurs are known,2,3 its origin is still not well understood. Based on the observed relationship between the {110}<112> deformation texture and the (113}<211> recrystallization texture, regardless of the effect of alloying elements2,4,5 or the symmetry of the deformation texture,&apos; there is a strong indication that a specific component of the deformation texture is related to a specific component of the recrystallization texture. Using the rotational reorien-tation relationship as a means of correlating the deformation and recrystallization textures, it was proposed that the deformation component which related the cube texture has {358)<523> indices."&apos; The investigation reported here was undertaken to seek experimental evidence for the validity of this proposition. Experimental Procedure Two copper single crystals having an initial orientation within 2" of (358) [523] indices were prepared in the manner described in Ref. 5. The purity of the copper was between 99.94 and 99.97 pct. The original dimensions of the crystals were as follows: specimen A, 0.465 in. thickness, 0.844 in. width, and 0.955 in. length; specimen B, 0.535 in. thickness, 1.120 in. width, and 1.36 in. length: Rolling was done on a laboratory rolling mill according to the following schedule: 0.010 in. per pass to 50 pct reduction in thickness, 0.005 in. per pass to 70 pct reduction inthickness, 0.002 in. per pass to 85 pct reduction in

Jan 1, 1958

By R. Drozd

"The Bullmoose Mine is currently under construction in the North East Coal area of British Columbia, and approximately $300 million will be spent to bring this 2.3 million-tonnes-per-year metallurgical and thermal coal mine into production by December 1, 1983.The project is an unincorporated joint venture undertaking, with Teck-Bullmoose Coal Inc., a wholly-owned subsidiary of Teck Corporation, holding 51%, Lornex Mining Corporation holding 39%, and Nissho-Iwai (Canada) Ltd. holding 10%. Bullmoose Operating Corporation will be the manager and operator of the project.This paper will broadly cover the history and exploration work on the property, the geology, open-pit mining plans and equipment, the preparation plant flowsheet from breaker station to clean coal silo, the 35 km highway truck haul, the railroad loadout system, manpower requirements, construction progress, approvals and permits, and general financial arrangements.IntroductionThe Bullmoose Mine Project"" is located about 87 road kilometres south of Chetwynd, B.C. and consists of an open-pit coal mine, a plant facility in the Bullmoose Creek valley below the mine, and a separate rail loadout facility on the British Columbia Railway Branchline near the new town of Tumbler Ridge some 35 road km to the east.The plant will be capable of producing a total of 2.3 million tonnes per year (mty) of washed metallurgical and thermal coal. Long-term metallurgical coal contracts for high quality, medium volatile, bituminous coal have been signed with nine Japanese buyers for 1.7 mty, and the balance of 0.6 mty will be thermal coal production.Plant construction began in the spring of 1982, and in May 1983, preproduction waste and overburden removal in the mine will commence. The plant should be fully operational by December 1983, and first vessel loading at the Ridley Island port is scheduled for January 1984."

Jan 1, 1983

By Dorricott M. G

Rock bolt installation is generally carried out in two steps. First the hole is drilled and the drill steel is extracted, then the bolt is inserted into the hole and tightened or grouted. With single pass bolting (SPB), however, these two steps can be carried out at the same time. This kind of bolting system has at least three advantages, (1) the time used for the bolt installation could be reduced, (2) the condition of safety for the operators could be improved, and (3) the degree of automation of the rock bolting practice could be increased. The study presented in this paper is concerned with the development of the SPB system. The current state of the system is discussed, and further improvement of the technique is explored.

Jan 1, 1992

By B. P. Faulkner, M. Weinecke

Svedala started a development program in 1997 to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed short-comings in the various approaches either process, mechanical, combination of factors, or trying to emphasis the production of low value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot plant development and commercial plant design.

Jan 1, 2001

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By Byron W. Cheever

Of the elements found in iron and steel, none has attracted more attention than phosphorus. It is considered the great enemy of the steel manufacturer-, and the chief aim has been and is to keep it out by using pure crude material, or when once in, to eliminate it or counteract its effect. Its presence is manifested in various ways, but most of all by producing a condition called cold-shortness. The first question, then, which presents itself is, What per cent. of phosphorus produces this condition ? I have searched very carefully for an answer to this question, but have failed to find one. Authors generally agree that wrought-iron may have a larger per

Jan 1, 1887

By Russell Millar

ACCORDING to the data of Maier and Ralston1 zinc vapor and carbon monoxide under the conditions in which they are present in a zinc condenser should, from a thermodynamic point of view, react to form zinc oxide and carbon, Zn (gas) + CO = ZnO (solid) + C. Calculations based on these results show that the gas mixture which is reducing to zinc oxide at the tempera-ture of the retort is oxidizing to zinc at the tempera-ture of the condenser. A series of experiments at the Pacific Experiment

Jan 9, 1928

By Robert C. Stephenson

In 1954, a year when general industrial production declined, it is significant that industrial mineral products continued in high demand. Phenomenal growth of the cement industry, increase in filler-fibre markets such as for asbestos and diatomite, expansion of the gypsum industry, and the increasing production of agricultural raw materials all illustrate the vitality of industrial minerals fields. Pioneer development of new industrial raw materials-wollastonite as a current example-requires keen foresight, hard work, and tremendous intestinal fortitude. The present-day requirements of industry for rigid quality control and uniformity of raw materials have resulted in highly specialized

Jan 3, 1955

By Quentin Rhoton

To benefit two endangered fish species, waterfowl and other wildlife, and water quality in the lake and downstream, the decision was made to remove levees that had been in place since the 1950s. Because the levee material was mainly dredged up lake bottom peat, it was decided to pare down the sites chosen for breaching with dozers and trackhoes. This material was spread out onsite instead of expensive removal by dumping elsewhere. Because of the instability of the final pared down levees and the lake level being at a ten-year low, it was decided to use explosives to breach four of the sites. After over five months of earthmoving and two weeks of loading holes, the levees were detonated the day before Halloween, 2007. Somehow pumpkins showed up to be part of the explosive activities.

Jan 1, 2009

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By Basil Prescott

Resume.—The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre-mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide type occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore, The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition. Introduction The Santa Eulalia district is situated in the State of Chihuahua, Mexico, and lies about 12 miles southeast of the capital, the city of Chihuahua. (See map, Fig. 1.) The district embraces the Sierra de La

Jan 1, 1915

By T J. Callaghan

The Avebury nickel mine in Western Tasmania is a disseminated nickel sulfide deposit hosted in intensely metasomatised Cambrian ultramafic resulting from later Devonian granite related hydrothermal activity.Variable metasomatism of the ultramafic has formed two distinct gangue mineral assemblages. Less metasomatised ultramafic is comprised of fine grained black antigorite with minor disseminated chromite, magnetite and pentlandite. Intensely metasomatised ultramafic is altered to a pale grey or green, coarsely crystalline tremolite/actinolite and diopside assemblage with minor magnetite, chromite and sulfides. Both gangue mineral assemblages are frequently intermixed in ore grade mineralisation.The bimodal gangue of either serpentinite or metasomatised ultramafic presents challenges to drilling, mining, resource estimation and mineral processing as they possess very different physical properties. Mineralised serpentinite has a mean bulk density of 2.8 g/cc and the ultramafic skarn a mean bulk density of 3.2 g/cc. Physically, the ultramafic skarn is hard to break percussively creating difficulties in the crushing circuit and reducing mine development rates. However, it is non-abrasive and grinds readily, resulting in increased diamond drilling rates and increased mill throughput. Conversely the serpentinite gangue is softer and breaks easily resulting in accelerated development rates and crushing circuit throughput. However, its fibrous nature reduces grinding efficiency, increasing bond work indices and reducing diamond drilling rates.Predicting the ratio of serpentinised to metasomatised ultramafic is possible through use of the resource blockmodel, assisting mine scheduling, predicting mill throughput rates, energy consumption and grade control drilling rates.CITATION:Callaghan, T J, 2017. Challenges of bi-modal gangue mineralogy in mining geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 23–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017