Search Documents

By G. L. Corrigan, J. R. Coleman

Four factors that largely determine the end product obtained when cement and water are mixed are the chemical compo ition of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the more finely ground a cement, and the greater the surface exposed in proportion to its mass, the more rapid is the hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.1 Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are poorer cementing materials than some of the more finely ground construction cements. On the other hand, often it is necessary to pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concerning the proper fineness range.

Jan 1, 1941

An "international gold conference" was held at Spokane, Wash., on Sept. 5, 1918, under the auspices of the Northwest Mining Association, which was attended by a large number of engineers, mine operators, and bankers, representing the northwestern states, as well as Alaska and British Columbia. The principal subject under consideration was the doleful condition of the gold-mining industry, gripped between the diminished purchasing value of its product, and the increased cost of its operation. Two resolutions were adopted by the meeting. The first approved the resolution adopted Aug. 12 by the American Gold Conference, a permanent organization formed at Reno, Nev., in which it is stated that relief by the United States to the gold producers of this country should he made to correspond with the increased cost of production, the extent of the relief to be fixed from time to time to Meet changing conditions. The second resolution, adopted after serious and long-continued discussion, was introduced by F. A. Ross, mining engineer, of Spokane, and a member of the Institute, and was as follows: WHEREAS, it is now clearly understood and agreed by the allied nations that national gold reserves must be augmented without delay if rapidly expanding credits are to be secured; and WHEREAS, at this time, the production of gold is daily decreasing to an alarming extent because of well known conditions that, render the mining of gold-bearing ores unprofitable; and WHEREAS there is no way by which the mining of gold-bearing ores may be made profitable except by the direct' aid and influence of the government; and WHEREAS the government has appealed to the mining industry for practical information and practicable suggestions upon this subject; therefore, be it

Jan 10, 1918

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because "the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

By José Sancho, Julia Ayala, Purificación García, Begoña Fernández

"Electrofilter dust, a residue generated in the last stage of the Bayer process in the hydroxide aluminum calcination, was characterized to evaluate the alumina that was potentially extractable with sulfuric acid. The process studied aims to produce aluminum sulfate for water coagulant uses, taking advantage of the residues that accumulate in large quantities in the proximity of plants with difficult recycling for storage. Acid leaching is carried out at different concentrations of sulfuric acid, at different temperatures, pulp densities, and times, to dissolve gibbsite and transition aluminas. The result is an aluminum sulfate solution without iron and with commercial specifications.IntroductionElectrofilter dust is a residue generated in the last stage of the Bayer Process [1] in the hydroxide aluminium calcination. The residue is a mixture of alumina and hydrates which have not completed their calcination process.Electrofilter dust, composed by alpha alumina, gibbsite and transition aluminas [2] can be leached in an acid medium by putting most of the aluminium in solution; the remaining residue should be mainly andisolved alpha alumina. In many hydrometallurgical processes, sulphuric acid has been selected as the cheapest and the most effective leachant [3,4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15]The aim of this study is to determine the effect of temperature, acid concentration and pulp density on the sulphuric acid leaching of electrofilter fines for aluminium dissolution, in order to produce aluminium sulphate for water coagulant uses. This will provide a commercial product and at the same time eliminate the environmental problem created as a result of the storage of large quantities of electrofilter fines in the vicinity of the Bayer plant."

Jan 1, 2008

By C. Orf. Chukabarah

Acoustic pollution (noise) is a significant mine environmental system problem. The U.S. Bureau of Mines (USBM), Environmental Protection Agency (EPA), Department of Labor (DOL) and other researchers have all performed contributory research on noise in mining environments. The present study addressed the problem of unavailability of a computerized, practical, routine, user-friendly, and user-editable, prose-styled application program with which one can determine (a) the noise exposure indices among mine workers, (b) mine system noise exposure level on time-weighted average basis, and (c) predictive relationships among mine workers' age, prior exposure to abnormal noise levels, prior auditory pathologies and the risk/degree of mining-induced hearing impairment. Results showed that such a program ("NEIL") is accomplishable. Additional results revealed that most U.S. mines operate within the statutory noise exposure levels. Furthermore, the mine worker's age was statistically confirmed to be the main predictive risk factor for mining-induced occupational hearing impairment.

Jan 1, 1992

By Steven J. Page, John A. Organiscak, Thomas Mal

Monitoring the miner respirable quartz dust exposure for compliance with U.S. federal regulations is mandatory to protect the health of coal miners. However, there is no technique available for the direct measurement of the respirable quartz dust concentration in the mining environment. The only means to estimate the respirable quartz dust concentration is to perform an analysis of the respirable dust sample collected, which contains both coal and quartz dust as well as other mineral constituents. For samples collected at coal mines, the U.S. Mine Safety and Health Administration (MSHA) utilizes the P7 method for respirable quartz analysis. The objectives of this work are to 1) evaluate the performance of the P7 method on field samples of low quartz mass loadings, 2) evaluate the magnitude of dust mass spatial variability within an enclosed cab environment, and 3) estimate the subsequent propagation of error in calculating the per. centage of quartz over a broad range of mass and quartz filter loadings at a surface coal mine. These objectives were achieved by obtaining surface coal mine dust samples over a 9-month time period in enclosed cabs of three drills and three bulldozers. By measuring weighing precision and using reasonable estimates for sampler variability, the dust mass spatial variability component was calculated by difference. The results show that 1) the P7 method can be precise and linear with quartz mass loadings as low as approximately 5 µmg of quartz, 2) the dust mass spatial variability, even within an enclosed cab environment, is the dominant factor of variability in propagation of error in estimating the quartz content of the obtained dust samples on a percentage basis, and 3) weighing precision is not a significant factor in error propagation. In addition to the enclosed cab samples, samples from eight surface coal mine drills were collected at various locations exterior to the drill cab. Significant data scatter at these outside locations strongly suggests that the ambient dust mass spatial variability has a significant effect on the propagation of error in estimating quartz content of the dust samples on a percentage basis.

By Ron Woolf, Corry Goumans

With increasing traffic volumes experienced thro u g hout North America, a common goal for Highway officials is to keep traffic flowing as much as possible and to keep disruptions to the flow to a minimum. Our experience throughout the US and Canada has shown that all Departments of Transportation are under extreme pressure from the private sector to keep highways open for various reasons, convenience and revenue being the most common. For example, on Highway 99, from Vancouver, BC to the Whistler resort area, local merchants, homeowners and ski hill operators exert extreme pressure on the Ministry of Transportation to keep the highway open, and in Pennsylvania, the Turnpike Commission requires traffic to flow on a continual basis. Loss of revenue in these two cases is the main impetus to keep the traffic moving.

Jan 1, 2003

By P. K. Narasimhargahavan

This paper discusses briefly the major reasons associated with the growth and its impact on the energy requirement and Environmental imbalance. A projection based on the present global Alumina and Al requirement indicate a substantial further growth of at least 30% over the next 10 years. It is indicated that the main factors which are likely to influence investments are the environmental factors such as the Climate Change and global response to the growing energy prices and sustainable development. Each of the developed / developing nations must find response to the GHG emissions which will encourage the Al Industry to make an effective contribution to global warming while preserving the international competitiveness of the industry - a challenging task. The efforts shall concentrate on improving energy efficiency in the industry possibly of the order of 25% over the next 10 to 20 years. The developments in this line are discussed.

Jan 1, 2010

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode amI across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1911

By A. A. Collins

H. R. BIANCO*—I should like to ask Mr. Collins if that statement he made about the addition of drosses to the blast furnace slowing down the blast furnace is a result of his own experience or a result of the experience of some older metallurgists; and perhaps I should ask him to define the type of drosses that he means. A. A. COLLINS (author's reply)— That has been my own personal experience with dross. On various occasions at Chihuahua we attempted to incorporate the dross in our regular blast furnace charge and to shut down the dross re-verberatory to try to save some money. As expected, we had very poor results. I think that Ed Fleming will well remember on one occasion, that was back about 1933, when we attempted the first experiment along this line, and as a result of the sulphur addition to the blast furnace to matte out the copper we ended up with hanging furnaces and mushy slags and abandoned the dross experiment, once again turning to the use of the reverbera-tory for handling dross. H. R. BIANCO—Is that dross you refer to from the drossing kettle ? A. A. COLLINS—Yes, the dross that I am referring to came from drossing kettles. Furthermore, to back up my previous assertion, I had occasion in 1943, while up at Leadville, to once again experience the routing of dross through the blast furnace with its sulphur addition, since they had no dross re-verberatory, and to observe that once thf dross was removed, the furnace was speeded up almost 100 tons a day. All of these are personal experiences and I think that Mr. Feddersen also has had a little experience along this line —in fact, I believe all of us have had some experience. H. R. BIANCO—I know at Trail they recirculate considerable dross through the blast furnaces and we also recirculate dross at Herculaneuin and I am not aware that it has done much towards slowing down the blast furnace. A. A. COLLINS—We have always had very poor results. In the first place you have got to add a sulphur addition to pick up that copper and once you do that, that sulphur is apt to combine with some of the zinc and you are going to form a little mush; before you know it you have furnace hangs and a poor working furnace. Now of course that depends on the amount of zinc you have on charge. But in 1943, Leadville had roughly about 7 pet zinc in their slag and it worked very poorly. Previously when they had 4 or 5 pet zinc in their slag it did not matter. B. L. SACKETT* At Tooele we had a great deal of experience with copper. We have always been able to keep a lead well, however, in spite of the fact we have run as much as 5 pet copper and only 15 pet lead on the charge. But regarding the handling of dross, our dross reverberatory furnace is only 7 or 8 years old. Before that we recirculated the dross through the furnace and thought we were doing a pretty nice job. Of course these things are all more or less relative—in other words you establish a certain condition much better than one of a few years ago and possibly as good as any other of which you know and you think you have pretty good results. When we first took the dross off of the blast furnace and put it through the dross reverberatory furnace we immediately found out that we had gained something very real in furnace speed. Since that time there have been occasions when, because of the dross reverberatory being down, we have had to use dross again through the blast furnace and that has checked our original experience in slowing down the furnace very definitely. So we feel that a dross reverberatory is a very valuable asset at the Tooele Plant. A. A. CENTER*—Mr. Sackett's being here reminds me of trying to run with a minimum of lead concentrates the maximum of dross producing electrolytic zinc plant residue. He came up from International Smelting Co. to help us get started on that. We took an old copper blast furnace at Great Falls, Montana, and made a lead furnace out of it by putting a lead well on the other long side which of course is a very unorthodox lead blast furnace. Our aim was to treat the residue from the electrolytic zinc plant, as I said, with a minimum of lead concentrates. That meant a maximum amount of dross. At that time selective flotation was not general practice, so our zinc concentrates ran relatively high in copper and other dross-producing elements; and of course these were largely in the zinc plant residue. I think we might call it muscle metallurgy, but we had an interesting, successful experience there and we ran for over a year thanks to Mr. Sackett's helping us get started. I have the details, but time does not permit. We did well enough so that the A. S. and R. Co. at East Helena kept boosting up the offer to us for the electrolytic zinc plant residue and there was not enough lead concentrate to supply two lead smelters there in Montana, so the matter finally finished up by the A. S. and R. Co. taking all of the residue under long term contracts.

Jan 1, 1950

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

"In order to achieve a high recovery of particles finer than 10µm, three types of dry Tower Mill (VD-1, KD-1, KD-2 and KD-3) have been developed. These mills differ from each other in the size of the comminuting part, the inside diameter and shape of the classifying part and the system involved in the collecting process. The last version (KD-3) of tower mills in which the comminuting and classifying operations has been separated, can produce particles finer than 10µm from a limestone ore sizing from 420 to 3360µm. In this tower mill, products in comminuting section are blown up and transported into the classifying column, made of an inverted cone on top of a cylinder, before they agglomerate and settle down. Fine particles are deported and recovered in a cyclone with a central spiral ribbon.Previous studies on the grinding efficiency of the tower mill KD-3 have shown how the maximum size of collected products increased with the airflow velocity, disturbing in the same way a smooth regulation of the grinding operation with the tower mill KD-3. A complete knowledge of factors that influence the maximum size of collected products is needed, therefore, to increase the efficiency of the grindingclassifying operation and ensure a better control over the collected products. The present study deals with this issue and, assuming that the structure of the classifying column could be one of these factors, its internal structure was modified (insertion of vertical plates, cone or horizontal nets) before carrying out comminution tests that would establish a relationship between the inward shape of the column and the maximum size of collected products. It was found that the weight of products collected in the cyclone decreases when a cone or some horizontal nets are inserted inside the column. At the same time, the weight of products collected in the column increases. This is due to the fact that coarse particles blown up from the comminution section collide with the base of the cone or the nets and settle down the bottom of the classifying column. Therefore, the cone and some horizontal nets inserted inside a classifying column, have the particularity to stabilize the maximum size of particles (15.1-17.5µm and 8.4-11.3µm) in the cyclone even when the airflow velocity in duct increased. These tools could of great help in the production of particles of definite size to fit for instance the paper industries requirements (production of limestone material sizing - 10µm as paper filler)."

Jan 1, 2003

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By S. J. Prison, C. R. Smith

The effect of fluid injection to control water coning in oil and gas wells was investigated. Analytical and model techniques were employed. The factors investigated were the position and length of the completion interval, the point of fluid injection, the viscosity of the injected fluid and the relative thickness of the oil and water sections. The resulting influence of these factors on the net producing water-oil ratio was determined. Several important conclusions can be drawn from the study. In general, it was found that the net producing water-oil ratio can be reduced by fluid injection. The magnitude of this reduction depended on the factors listed above. An important practical consideration is that the injection fluid may be either oil or water. If the injected fluid is less dense than the connate water of the reservoir, the fluid will not be lost. This fact is reassuring when valuable oil is being injected. Efforts to suppress water production were more successful when the injection fluid was more viscous than the reservoir oil, or when a zone of reduced permeability existed in the vicinity of the point of fluid injection. Under test conditions, little benefit was derived through the use of impermeable barriers or cement "pancakes". INTRODUCTION The occurrence of water coning has been known for at least 60 years. In thin oil or gas pay sections, the presence of an oil-water or gas-water contact hinders production and often causes early abandonment of the afflicted well if a completion is even attempted. Even when relatively thick pay sections are found, the encroachment of water when a water drive is present will eventually pose serious water coning problems. This water is often corrosive, expensive to separate from the oil or gas and is costly to dispose of. The theory of water coning has been discussed by a number of authors. 1,2,3,4 Briefly, water coning to the producing interval in a well is due to pressure gradients resulting from the production of fluid from the reservoir. These pressure gradients will cause a water cone to rise toward the bottom of the producing interval if a water-oil or water-gas contact exists. The tendency of the water to cone is offset or partially offset by gravity forces since the water has a higher specific gravity than the oil. A balance then exists between two forces, gravitational forces arising from the difference in specific gravities of the oil and water, and the pressure gradients causing the flow of fluids to the wellbore. If the pressure gradient exceeds the gravitational force, water coning to the wellbore occurs and water production results. Through the years considerable thought has been given to the water coning problem. More than 50 U. S. Patents have been granted to inventors on the subject. A relatively complete literature review of the water coning problem has been made. 5 A number of these patents hold considerable promise for the solution or the partial solution of the water and/or the coning problem. Very little has been written describing field tests of techniques for the suppression of water coning. A notable exception is the paperby West. 6 He reports success in reducing gas coning by a combination of gravel packing and oil injection above the oil-producing interval. He also describes a comparable method to prevent water coning, but provides no field examples. This study experimentally and analytically verifies the benefits of oil injection as a means of partially or completely suppressing the water cone. While the gas coning problem was not treated, it is anticipated that results comparable to those obtained in water suppression could be obtained with reduced oil injection since the viscosity contrast between oil and gas exceeds that between oil and water. For the purpose of this study, the conventional potential flow theory was applied to the water-coning problem. The experimental verification centered on both a radial and a linear model. The model study permitted the investigation of complex flow configurations and the use of fluids of differing densities and viscosities. No analytic expressions are available to permit a solution of the problem as stated (see Fig. 1).

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Giannini LM, Carras S

A fundamental problem in mine planning is that of determining the "optimum pit limit" of a mine. This optimum pit limit yields information which is considered essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long -, intermediate -, and short-range mine plans. Since the mid 1960's a number of mathematical techniques based on the "block model" have been proposed for solving this problem. When applied to large ore-bodies the implementation of these techniques, especially the more elaborate ones, poses considerable computational problems. In this paper we report on our work, done jointly with Systems Research Institute of Australia (SRIA), in devising strategies for overcoming these Problems.

Jan 1, 1986

A GREAT and incomparable speculation is whether the discovery of A compounding the powder used for guns came to its first inventor from the demons or by chance. With this invention he certainly far surpassed all men of every age from the creation of the world up to that day when it was announced by him-men so very learned, indeed like angels and of divine intellect, powerful in every knowledge and power. These had not only revived-arts and sciences and discovered new ones with their intellects, but they had information about all natural

Jan 1, 1942

By H. A. Coy

THE Mascot mines of the American Zinc Co. of Tennessee are situated in the Holston River valley, in Knox County, Tennessee, about 13 miles (20.9 km.) east of the city of Knoxville, and form a property of three operating shafts and one open pit. A second open pit is located at Jefferson City about 16 miles (25.8 km.) east of the Mascot mines. Geology Topography.-The principal topographical features of the region within which the zinc deposits occur is a series of parallel northeast and. southwest ridges which reach altitudes of 200 to 400 ft. (61 to 122 m.) above the valley. These ridges are formed of resistant formation such as sandstone, quartzites, etc., while the valleys are occupied principally by limestone, including Knox dolomite, and by shale and other formations subject to quick erosion. The Holston River valley is wide and open with a rolling surface. Sink holes are common to the limestone portion, the general aspect of the valley being that of well-rounded hills with low intervening valleys superimposed upon which is a characteristic sink-hole topography. General Geology.-According to Keith, the rock formation of the area extends from the lower Cambrian into the Silurian. The region has undergone severe deformation with heavy faulting, the underlying Cambrian having been brought to the surface by a series of low angle thrust faults, the strike of the faults and formations paralleling the general northeast and southwest direction of the topography and clipping at varying angles to the southeast. In general the Cambrian quartzites, sandstone, etc., occupy the ridges while the Cambro-Silurian dolomites, limestone and shales occur principally in the valleys. Of the latter, the Knox dolomite is of particular interest to this paper in that it is the ore carrier in the Mascot area. The ore is associated with more or less irregular breccia zones, the degree of brecciation varying from-a fine crushing to a breaking that involves blocks of large size. The breccia zones

Jan 9, 1917

By H. W. Johnson

DURING part of the year 1932, conditions at the plant of the Inland Steel Co. made possible the collection of data on two of the variables of blast-furnace operation, between which we observed an interesting correlation. The variation in percentage of coke ash in the coke seemed to be reflected in the variations in percentage of silicon and sulfur present in the iron. This subject is of particular interest during this period of low production because of its effect on quality and cost of pig iron. The consumers of pig iron are now more exacting in their requirements. Formerly 0.050 per cent sulfur was considered satisfactory; now many foundries and steel plants insist on iron under 0.030 per cent sulfur and expect it to average 0.025 per cent sulfur. To attempt to produce iron so low in sulfur and still have reasonably good furnace operation means that everything possible must be done to minimize all variations. This subject is also directly connected with the cost of producing iron. A blast furnace operates most economically and efficiently in rather narrow limits and so any variable that has range enough to disturb regular operation must be moderated. The importance of regularity is accepted and the methods followed to eliminate variations in materials such as coke and iron ore are recognized as indispensable. Uniformity of Ore and Variations in Coke Ash The delivering of uniform cargoes of well mixed ore to the blast furnace involves much handling and expense, but it is accepted that the trouble and expenditure are justified. After the ore reaches the dock, further mixing is assured by spreading ore in thin layers, preventing segregation by keeping piles level, variations in digging, and the use of several bins for one ore. And finally, the fact that the furnace burden generally contains three or more ores, together with several miscellaneous materials, eliminates the possibility of ill effects due to variations in any one. Thus, much effort is made to insure a uniform ore. But a variation in the percentage of silicon in ore is less detrimental than a variation in the percentage of ash in coke. The former affects

Jan 1, 1933

By Isaac A. Zlochower

A number of ignition incidents involving mining and farm equipment have illustrated the surprising danger of drilling, cutting, or otherwise penetrating sealed compartments or frames that are filled with metal scrap for ballast. The presence of chemically-reactive metals (or electrochemically-active pairs), such as zinc in galvanized steel, can produce hydrogen from moisture in the steel scrap, and the resulting pressure, due to the internally-generated hydrogen, can produce an easily-ignited gas jet when the sealed component is penetrated.

By E. V. Daveler

THE milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. CHARACTER OF ORE The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver 0.10 oz. Magnesia 0.4 per cent. Silica 59.7 per cent. Sulfur 1.2 per cent. Iron 5.2 per cent. Lead 0.1 per cent. Alumina 21.4 per cent. Zinc 0.2 per cent. Lime 5.0 per cent.

Jan 1, 1920