Search Documents

By M. J. King

The Chino Smelter embarked on a program to reduce smelter emissions. Fugitive sulfur dioxide and particulate emissions were reduced by (i) removing the flash furnace settling chamber and (ii) installing a baghouse, to treat converter secondary emissions. Neutralization plant capacity was increased, to accommodate increased flow from the flash furnace off-gas cleaning system and to reduce costs.

Jan 1, 1998

By Donald W. Mitchell

Studies were made in the Bureau of Mines Experimental coal mine to evaluate the effectiveness of a few extinguishing agents and techniques for controlling a fire on a simulated mining machine. The investigation showed that water containing an alkali-metal salt or a surface-active (wetting) agent was more effective than water alone. For close attack, fog applications was the most effective technique studied; high rates of agent application controlled the fire more quickly than low rates. The ability to control the fire increased as the distance of attack decreased. Dry powders controlled the fire when applied by shovel but not when applied airborne by rock-dust distributor or by hand fire extinguishers. Dry alkali-metal salt powders (potassium and sodium bicarbonates and sodium tetraborate) quenched the fire more readily than limestone dust. In each instance the finer powder, the greater its effectiveness. In an open ventilated entry, smoke and hot gases backed against the air currents. An airspeed of 230 feet per minute was required to permit approach to within 10 feet of the fire. At lower airspeeds, approach could be made by extending the brattice across the bottom two-thirds of the entry, by pushing the smoke ahead with water sprays, or by discharging dust from a rock-dust distributor. In a dead-end entry, the fire was approached to within 30 feet by coursing fresh air along an airtight line brattice; however, it was safer, easier, and less time-consuming to attack the fire from a fresh-air base 100 feet away with a solid stream or by high-expansion foam; the latter method was more effective.

Jan 1, 1961

Simulation has established itself as an accepted tool for the design and optimization of complex minerals processing plants. This paper addresses the use of simulation as a tool for the design and optimization of carbon-in-pulp and carbon-in-leach (CIP/CIL) plants. The complex, interactive nature of CIP/CIL plants makes detailed experimentation an expensive and time consuming approach to CIP/CIL plant design and/or optimization. This paper discusses a simulation-based software tool that can make the process of CIP/CIL plant design and/or optimization much more cost effective. Many of the issues and problems pertaining to the use of simulation for CIP/CIL design and operation are generic. Thus, this paper also attempts to highlight generic issues that must be solved before simulation will become a more widely used design and optimization tool. Requirements for the application of simulation for CIP/CIL plant design and optimization are highlighted. Similar problems and issues can be identified for most mineral processing plants.

Jan 1, 1994

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

By A. Pearson, Auld. F. A., S. O. Colbeck

"To minimise mine shaft maintenance over the long-term, some potash mine shaft sinking projects have required the provision of a continuous fully welded waterproof steel liner over a substantial depth to achieve zero water ingress. This brings many challenges, including the implementation of a bottom-up construction sequence incorporating extensive waterproof welding and how to ensure the integrity of the welded liner when subject to substantial temperature fluctuations that are likely to occur with a composite steel-concrete liner placed within an artificially frozen shaft excavation. This paper highlights the key challenges and discusses multiple mitigation measures including vertical shaft movement joints and a combined structural-thermal analysis approach. INTRODUCTION Whilst the application of combined steel and concrete shaft liners using a fully welded steel liner is not new and has been used in several previous projects, most notably at Lanigan (Storck, 1968 & Roesner, 1980), recently the need to provide a continuously welded steel waterproof liner for over 800 m length of shaft for a potash mine has been considered. The need for a fully continuous welded steel liner arises from the perceived benefits of providing a fully dry shaft environment to; increase the life expectancy of the shaft; reduce routine maintenance particularly combatting salt accretion and minimising wash down practices; and improve long-term ground stability by preventing salt dissolution. Whereas previous projects have employed discontinuous sections of steel liner, when a fully continuous liner is employed longitudinal shaft strains from thermal changes result in significant deformations that must be either explicitly accommodated or resisted. Note, these thermal vertical expansion forces are more than capable of lifting the shaft collar and head frame structures should they be fixed in place. Typically, shafts are designed to resist vertical forces (collar loads and self-weight) by creating mechanical interlock with the adjacent ground. In competent rock this occurs incrementally with the construction of the shaft liner, and occasional hitch/crib structures are constructed as intermediate foundations to guarantee the transfer of vertical forces at distinct horizons. Usually this means cribs are constructed at first rock head, above the station level, and at the sump, although sometimes additional cribs are formed when entering and exiting weak strata or when a change in shaft liner construction is required."

Jan 1, 2019

By AIME AIME

COAL occupied a large place in the technical sessions of the Institute at its annual meeting for in addition to three sessions specifically de- voted to coal the two sessions on mine ventilation and the two on ground movement and subsidence, which are reported under their own headings, were primarily concerned with coal. The first session on coal was a joint one with the Iron and Steel Division, on Wednesday afternoon, with F. H. Crockard and J. R. Campbell presiding as joint chairmen and the latter actually officiating. The principal topic of discussion was G. S. Scott's paper "Evaluation of Coal for the Making of Blast- Furnace Coke," which has been published as T. P. 159. The author made a brief statement of its con- tents to start the discussion and the chairman, after briefly reviewing it himself, called on C. A. Meissner to start the discussion. He briefly reviewed the economic factors in the use of coal for coke-making, saying that not only .does the removal of 1 per cent of ash from the coal reduce the cost of pig iron 12 or 13c. per ton, but it also permits coke of satisfactory structures to be made from a coal which otherwise could not be used. He stressed the importance of uniformity in blast-furnace fuel and discussed the benefit of mixing different coals as raw material for the coke oven and cited experience with Illinois coals.

Jan 1, 1929

By Elmer W. Pehrson

Minerals have played a prominent role in the affairs of man and nations since time immemorial but with the advent of the industrial revolution, expanding use of the products of the mineral kingdom became synonymous with the material progress of mankind. Individuals and business groups have recognized this fact so have been aggressive in searching for and utilizing mineral resources, with notable success. Indeed, their achievements are primarily responsible for the present Machine Age. On the other hand, until recently the body politic has failed to grasp fully the essentiality of minerals although, at times, access to mineral supplies has been an important factor in the political maneuvers of nations. This chapter is concerned primarily with the broader political and economic relationships of mineral resources to the world economy, and with the internal and external actions of nations in the field of minerals. Many factors that condition the mineral economy of regions and the world as a whole, influence the internal and external affairs of individual nations. The more important of these are: 1. The nature of man's dependence on minerals. 2. The problems resulting from the unique characteristics of mineral occurrence. 3. Geopolitical concepts. 4. Minerals and world power. Actions of individual nations affecting their mineral economy seek two basic objectives: 1. Attainment and maintenance of prosperity. 2. Military security. Other objectives may be cited but on careful analysis they become integral parts or extreme phases of the two points noted above. For example, the twentieth century aggressions of the USSR, Germany, Italy, and Japan might be considered as direct bids for world power but they also can be interpreted as exaggerated or mistaken efforts toward military security and peacetime prosperity. Similarly, trade barriers, nationalization of industries, foreign exchange manipulations, taxation, monopolistic prac-

Jan 1, 1964

By Kent C. Condie

Precambrian terranes in the Rocky Mountain region decrease progressively in age from the Archean Wyoming Province (> 2.5 b.y.) to the late Proterozoic in West Texas (figs. 1,2). Within the Wyoming Province, most dates fall near 2.7 b.y. although some are recorded at 2 3.8, 2.9, and 2.6 b.y. Although Penokean (- 1.8 b.y.) deformation and plutonism are recorded in southeastern Wyoming, most Precambrian rocks south of the Wyoming shear zone, which separates the Archean and Proterozoic provinces, are < 1.76 b. years in age. Supracrustal rocks in Colorado, western Arizona, and northern New Mexico fall in the range of 1.72-1.76 b.y., those in central New Mexico about 1.65 b.y., those in southeastern Arizona and southwestern New Mexico about 1.70 b.y., and those in West Texas 1.1-1.2 b.y. The Wyoming Province is comprised chiefly of 2.7 or 2.9 b.y. tonalitic gneiss terranes intruded by 2.6 b.y. granites in the central and southern parts of the province. Supracrustal rocks are minor and include greenstone belts comprised chiefly of pillow- ed tholeiites and graywackes and remnants of quartzite-shale successions. Metamorphic grade in greenstone-gneiss terranes ranges from upper greenschist to amphibolite facies and in quartzite-gneiss terranes from upper amphibolite to granulite facies.

Jan 1, 2013

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers In their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the first three sites: Bethel, Kivalina (Red Dog), and Omalik Lagoon. The mineral deposits near Bethel are primarily gold and mercury; the nearest deposit being 55 mites away. Because of the expense of constructing and maintaining a road over the poorly drained lowlands, the potential of Bethel as a port site in the near-term is considered to be low. The Kivalina site currently serves the Red Dog mine and has the potential to handle material for similar deposits in the area. Results from a lead-zinc mine model indicate that potential for additional mine development exists in the area. Coal is the major deposit type found near the Omalik Lagoon site. Due to environmental constraints, development of a large-scale mine producing coal for export is considered unlikely. A small-scale coal mine model was used to examine the feasibility of producing coal for regional use. This alternative may be feasible but would require conversion of heating/generating equipment in the area.

Jan 1, 2011

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By Stanislas Mauuary

Price pressure is a real challenge on the stainless steel market. With market globalization, increase production capacity and exorbitant raw material, the margins are squeezing for stainless strip producers. Primetals Technologies offers a wide range of advanced technological solutions to secure the margins of our customers. Our solutions, implemented with professional project management, allow an optimum coil to market time, securing then the return on investment for the investor. Among the possible lever used to optimize the production route, one drastic step can be made to cut rolling time and cost by replacing the common 20-Hi mill stand reversing process by state of art high capacity X-HI® stands in continuous rolling line. Other source of savings can be implemented by integrated several process steps together (rolling, annealing, pickling, skin passing), achieving then savings on stocks and logistics while coil processing is reduced to fraction of hour. Additional solutions can also be implemented on the new, as well as existing line, like maintenance free solid state laser welder, skin-pass and tension levelers, in-line inspection system coupled with process and quality management system.

Aug 17, 2017

By Edward R. Lauer

Energy conservation is an integral part of Canada&apos;s energy strategy. We must pursue conservation and energy management vigorously if we are to remain competitive in domestic and world markets, and minimize our reliance on external energy sources. Energy management in industry is discussed from three viewpoints: (l) as a means of directly improving profitability; (2) as a major factor in the supply picture; and (3) as a significant influence on Canada&apos;s balance of payments and over-all economic well-being. The Federal role in promoting a voluntary industrial energy conservation program is described.

Jan 1, 1977

By V. Rastogi

Acid rock drainage is the result of exposure of sulfidic materials, such as pyrites and sulfidic ores, to air and water. The oxidation of these sulfides is catalyzed by more than a million times by the bacteria Thiobacillus jerrooxidans and close families. Inhibition of these bacteria can mitigate 98% or more of the acid loading generated. This can be achieved by the use of certain surfactants that are selectively bactericidal to the lithotropic acidophilic bacteria. Bactericides are used in two ways. As periodic or continuous treatments for prevention of acidification of material actively handled and moved, and in controlled release form for reclamation where treatment sets up a change in site microbiology to replace Thiobacillus jerrooxidans with heterotrophic bacteria and creates a stable site without need for further treatments. Use of bactericides begins with laboratory testing of the site material to qualify the site for bactericide treatment and dosage determination. Site specific treatments are designed for active sites and reclamation. Once acid production is controlled, solubilization of metals is correspondingly reduced. Results and economics of use from active and reclamation sites are presented.

Jan 1, 1995

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization&apos;s structure that addresses the immediate and long-term impact of a company&apos;s products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By Eugene H. Skinner

The U.S. Bureau of Mines conducted experiments on the use of lightweight concrete in the density range of 100 Ib/ft3 for liners in underground mines. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a second section constructed in a drift using an air-supported formwork. The lightweight concrete in the two underground test sections was placed using piston pumps and a slickline. Fiber reinforcement was added to the concrete in the mine sections without any apparent problems with either pumping or placement of the concrete. In another experiment, the Bureau and Hecla Mining Co., Mullan, rD, used lightweight concrete in the density range of 25 Iblfe to replace timber blocking in a raise preparation structure. Other experiments are described in which low-density, lightweight concrete blocks were produced for mine ventilation doors, stoppings, and barricades. Other mine uses reviewed include pillars and collapsing beams. An advantage of low-density concrete is that it will display up to 50% deformation at a constant yield stress. These hlllovative concepts in deformable concrete lining systems will aid mine operators by decreasing capital and maintenance costs, increasing the available space in underground haulageways, and providing productivity gains and improved resource recovery in the soft, caving, squeezing, or bursting grollnu conditions often found in deep mines.

Jan 1, 1989

By Roger M. Sherman

[Investigation of mine land characteristics, evaluation of irrigation systems, and evaluations by the mining industry, determined that irrigation is a feasible method for aiding revegetation of coal mined lands in western arid and semi-arid regions. The various regions studied displayed a commonality of characteristics which enables, independent of the site or region, the recommendation of solid set irrigation. Irrigation should be supplemental by complimenting natural precipitation and be should implemented on a temporary basis.]

Jan 1, 1980

This paper firstly reviews the requirements for container and hopper design for reliable discharge. Discussion is then directed to the evaluation of the consolidation stresses acting in both in both the cylinder and hopper sections during both initial and flow conditions. Here the vast difference, especially in vicinity of the bin outlet, between the initial or filling and flow conditions is highlighted. This vast difference has major design and operation implications. A further major implication is that all bulk solids must dilate to flow. The opportunity to simultaneously attain reliable discharge and partial moisture removal is also examined.The selection of design parameters to maximise the consolidation stresses in both the cylindrical and hopper sections is detailed. In regard to the latter, it is recommended fine coal bins be discharged using low friction lined transition hoppers with large outlet spans. Such outlets will discharge fine coal in a relatively compacted state. This compaction state should exhibit minimum water retention and short term moisture uptake.

Jan 1, 1998

By Ben Bowman

For certain ferroalloy furnaces, such as ferrochrome or ferromanganese, there is still doubt about the mechanisms operating under the electrode tips. In this paper a model is built that does not call upon an arc. The medium is best described as an electrically conducting slurry, a mixture of liquids, solids and gas. There are two sources of propulsion, the Lorentz force within the conducting part and buoyancy generated by CO bubbles, creating two opposed poloidal circulation loops, downward below the electrode axis and upward further out.

Jan 1, 2014

By Sushanta Majumder

The physico-chemical characteristics of raw materials used for the production of iron ore pellets have a strong influence on the productivity of pelletization operations and on the quality of pellets. Since iron ores from different sources are used for making iron ore pellets and since the quality of the ores varies with time, there is a need to optimize and control pellet plant operations on a regular basis to achieve optimum productivity while maintaining pellet quality within the desirable specifications. In order to achieve this objective, a model-based on-line optimization system was implemented on two industrial scale induration furnaces. The optimization system consists of a rigorous mathematical model of the induration process, a model for the permeability of the bed of pellets, a statistical model for the quality of iron ore pellets and an optimization module based on sequential quadratic programming. The rigorous model is tested on-line using the wind-box temperature available real-time. The process was optimized to enhance induration furnace productivity for the given constraints on pellet quality parameters such as the cold compressive strength (CCS) and Tumble Index (TI), and other equipment design parameters. Process variables such as induration machine speed, cold air flow rate and hood temperature profile were used as the optimization variables. The on-line optimization system was successfully implemented in two industrial induration furnaces and lead to enhanced productivity. Details of the on-line optimization system and results of process optimization will be presented.

Sep 1, 2012

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941